sergiotarxz/nuttx
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
78a2465af4
nuttx/arch/arm/src/sam34/sam3u_gpio.h

203 lines
8.5 KiB
C
Raw Blame History

/************************************************************************************
* arch/arm/src/sam34/sam3u_gpio.h
* General Purpose Input/Output (GPIO) definitions for the SAM3U
*
* Copyright (C) 2009-2011, 2013 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
************************************************************************************/
#ifndef __ARCH_ARM_SRC_SAM34_SAM3U_GPIO_H
#define __ARCH_ARM_SRC_SAM34_SAM3U_GPIO_H
/************************************************************************************
* Included Files
************************************************************************************/
#include <nuttx/config.h>
/************************************************************************************
* Pre-processor Definitions
************************************************************************************/
/* Configuration ********************************************************************/
#undef GPIO_HAVE_PULLDOWN
#undef GPIO_HAVE_PERIPHCD
#undef GPIO_HAVE_SCHMITT
#undef GPIO_HAVE_DELAYR
/* Bit-encoded input to sam_configgpio() ********************************************/
/* 16-bit Encoding:
*
* MMCC CIII VPPB BBBB
*/
/* Input/Output mode:
*
* MM.. .... .... ....
*/
#define GPIO_MODE_SHIFT (14) /* Bits 14-15: GPIO mode */
#define GPIO_MODE_MASK (3 << GPIO_MODE_SHIFT)
# define GPIO_INPUT (0 << GPIO_MODE_SHIFT) /* Input */
# define GPIO_OUTPUT (1 << GPIO_MODE_SHIFT) /* Output */
# define GPIO_PERIPHA (2 << GPIO_MODE_SHIFT) /* Controlled by periph A signal */
# define GPIO_PERIPHB (3 << GPIO_MODE_SHIFT) /* Controlled by periph B signal */
/* These bits set the configuration of the pin:
*
* ..CC C... .... ....
*/
#define GPIO_CFG_SHIFT (11) /* Bits 11-13: GPIO configuration bits */
#define GPIO_CFG_MASK (7 << GPIO_CFG_SHIFT)
# define GPIO_CFG_DEFAULT (0 << GPIO_CFG_SHIFT) /* Default, no attribute */
# define GPIO_CFG_PULLUP (1 << GPIO_CFG_SHIFT) /* Bit 11: Internal pull-up */
# define GPIO_CFG_DEGLITCH (2 << GPIO_CFG_SHIFT) /* Bit 12: Internal glitch filter */
# define GPIO_CFG_OPENDRAIN (4 << GPIO_CFG_SHIFT) /* Bit 13: Open drain */
/* Additional interrupt modes:
*
* .... .III .... ....
*/
#define GPIO_INT_SHIFT (8) /* Bits 8-10: GPIO interrupt bits */
#define GPIO_INT_MASK (7 << GPIO_INT_SHIFT)
# define _GIO_INT_AIM (1 << 10) /* Bit 10: Additional Interrupt modes */
# define _GPIO_INT_LEVEL (1 << 9) /* Bit 9: Level detection interrupt */
# define _GPIO_INT_EDGE (0) /* (vs. Edge detection interrupt) */
# define _GPIO_INT_RH (1 << 8) /* Bit 9: Rising edge/High level detection interrupt */
# define _GPIO_INT_FL (0) /* (vs. Falling edge/Low level detection interrupt) */
# define GPIO_INT_HIGHLEVEL (_GIO_INT_AIM | _GPIO_INT_LEVEL | _GPIO_INT_RH)
# define GPIO_INT_LOWLEVEL (_GIO_INT_AIM | _GPIO_INT_LEVEL | _GPIO_INT_FL)
# define GPIO_INT_RISING (_GIO_INT_AIM | _GPIO_INT_EDGE | _GPIO_INT_RH)
# define GPIO_INT_FALLING (_GIO_INT_AIM | _GPIO_INT_EDGE | _GPIO_INT_FL)
# define GPIO_INT_BOTHEDGES (0)
/* If the pin is an GPIO output, then this identifies the initial output value:
*
* .... .... V... ....
*/
#define GPIO_OUTPUT_SET (1 << 7) /* Bit 7: Inital value of output */
#define GPIO_OUTPUT_CLEAR (0)
/* This identifies the GPIO port:
*
* .... .... .PP. ....
*/
#define GPIO_PORT_SHIFT (5) /* Bit 5-6: Port number */
#define GPIO_PORT_MASK (3 << GPIO_PORT_SHIFT)
# define GPIO_PORT_PIOA (0 << GPIO_PORT_SHIFT)
# define GPIO_PORT_PIOB (1 << GPIO_PORT_SHIFT)
# define GPIO_PORT_PIOC (2 << GPIO_PORT_SHIFT)
/* This identifies the bit in the port:
*
* .... .... ...B BBBB
*/
#define GPIO_PIN_SHIFT 0 /* Bits 0-4: GPIO number: 0-31 */
#define GPIO_PIN_MASK (31 << GPIO_PIN_SHIFT)
#define GPIO_PIN0 (0 << GPIO_PIN_SHIFT)
#define GPIO_PIN1 (1 << GPIO_PIN_SHIFT)
#define GPIO_PIN2 (2 << GPIO_PIN_SHIFT)
#define GPIO_PIN3 (3 << GPIO_PIN_SHIFT)
#define GPIO_PIN4 (4 << GPIO_PIN_SHIFT)
#define GPIO_PIN5 (5 << GPIO_PIN_SHIFT)
#define GPIO_PIN6 (6 << GPIO_PIN_SHIFT)
#define GPIO_PIN7 (7 << GPIO_PIN_SHIFT)
#define GPIO_PIN8 (8 << GPIO_PIN_SHIFT)
#define GPIO_PIN9 (9 << GPIO_PIN_SHIFT)
#define GPIO_PIN10 (10 << GPIO_PIN_SHIFT)
#define GPIO_PIN11 (11 << GPIO_PIN_SHIFT)
#define GPIO_PIN12 (12 << GPIO_PIN_SHIFT)
#define GPIO_PIN13 (13 << GPIO_PIN_SHIFT)
#define GPIO_PIN14 (14 << GPIO_PIN_SHIFT)
#define GPIO_PIN15 (15 << GPIO_PIN_SHIFT)
#define GPIO_PIN16 (16 << GPIO_PIN_SHIFT)
#define GPIO_PIN17 (17 << GPIO_PIN_SHIFT)
#define GPIO_PIN18 (18 << GPIO_PIN_SHIFT)
#define GPIO_PIN19 (19 << GPIO_PIN_SHIFT)
#define GPIO_PIN20 (20 << GPIO_PIN_SHIFT)
#define GPIO_PIN21 (21 << GPIO_PIN_SHIFT)
#define GPIO_PIN22 (22 << GPIO_PIN_SHIFT)
#define GPIO_PIN23 (23 << GPIO_PIN_SHIFT)
#define GPIO_PIN24 (24 << GPIO_PIN_SHIFT)
#define GPIO_PIN25 (25 << GPIO_PIN_SHIFT)
#define GPIO_PIN26 (26 << GPIO_PIN_SHIFT)
#define GPIO_PIN27 (27 << GPIO_PIN_SHIFT)
#define GPIO_PIN28 (28 << GPIO_PIN_SHIFT)
#define GPIO_PIN29 (29 << GPIO_PIN_SHIFT)
#define GPIO_PIN30 (30 << GPIO_PIN_SHIFT)
#define GPIO_PIN31 (31 << GPIO_PIN_SHIFT)
/************************************************************************************
* Public Types
************************************************************************************/
/* Must be big enough to hold the 16-bit encoding */
typedef uint16_t gpio_pinset_t;
/************************************************************************************
* Inline Functions
************************************************************************************/
#ifndef __ASSEMBLY__
/************************************************************************************
* Public Data
************************************************************************************/
#undef EXTERN
#if defined(__cplusplus)
#define EXTERN extern "C"
extern "C"
{
#else
#define EXTERN extern
#endif
/************************************************************************************
* Public Function Prototypes
************************************************************************************/
#undef EXTERN
#if defined(__cplusplus)
}
#endif
#endif /* __ASSEMBLY__ */
#endif /* __ARCH_ARM_SRC_SAM34_SAM3U_GPIO_H */
Reference in New Issue View Git Blame Copy Permalink