a0ce81d659
to save the preserved space(1KB) and also avoid the heap overhead Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com> Change-Id: I694073f68e1bd63960cedeea1ddec441437be025 |
||
---|---|---|
.. | ||
configs/nsh | ||
include | ||
scripts | ||
src | ||
Kconfig | ||
README.txt |
Nucleo-F072RB README ==================== This README file discusses the port of NuttX to the STMicro Nucleo-F072RB board. That board features the STM32F072RBT6 MCU with 128KiB of FLASH and 16KiB of SRAM. Contents ======== - Status - Nucleo-64 Boards - LEDs - Buttons - Serial Console - Configurations Status ====== 2017-04-28: After struggling with some clock configuration and FLASH wait state issues, the board now boots and the basic NSH configurations works without problem. A USB device driver was added along with support for clocking from the HSI48. That driver remains untested. 2017-04-30: I tried using the I2C driver with the I2C tool (apps/system/i2c). I may have something wrong, but at present the driver is just timing out on all transfers. Nucleo-64 Boards ================ The Nucleo-F072RB is a member of the Nucleo-64 board family. The Nucleo-64 is a standard board for use with several STM32 parts in the LQFP64 package. Variants including: Order code Targeted STM32 ------------- -------------- NUCLEO-F030R8 STM32F030R8T6 NUCLEO-F070RB STM32F070RBT6 NUCLEO-F072RB STM32F072RBT6 NUCLEO-F091RC STM32F091RCT6 NUCLEO-F103RB STM32F103RBT6 NUCLEO-F302R8 STM32F302R8T6 NUCLEO-F303RE STM32F303RET6 NUCLEO-F334R8 STM32F334R8T6 NUCLEO-F401RE STM32F401RET6 NUCLEO-F410RB STM32F410RBT6 NUCLEO-F411RE STM32F411RET6 NUCLEO-F446RE STM32F446RET6 NUCLEO-L053R8 STM32L053R8T6 NUCLEO-L073RZ STM32L073RZT6 NUCLEO-L152RE STM32L152RET6 NUCLEO-L452RE STM32L452RET6 NUCLEO-L476RG STM32L476RGT6 LEDs ==== The Nucleo-64 board has one user controllable LED, User LD2. This green LED is a user LED connected to Arduino signal D13 corresponding to STM32 I/O PA5 (PB13 on other some other Nucleo-64 boards). - When the I/O is HIGH value, the LED is on - When the I/O is LOW, the LED is off These LEDs are not used by the board port unless CONFIG_ARCH_LEDS is defined. In that case, the usage by the board port is defined in include/board.h and src/stm32_autoleds.c. The LEDs are used to encode OS-related events as follows when the red LED (PE24) is available: SYMBOL Meaning LD2 ------------------- ----------------------- ----------- LED_STARTED NuttX has been started OFF LED_HEAPALLOCATE Heap has been allocated OFF LED_IRQSENABLED Interrupts enabled OFF LED_STACKCREATED Idle stack created ON LED_INIRQ In an interrupt No change LED_SIGNAL In a signal handler No change LED_ASSERTION An assertion failed No change LED_PANIC The system has crashed Blinking LED_IDLE MCU is is sleep mode Not used Thus if LD2, NuttX has successfully booted and is, apparently, running normally. If LD2 is flashing at approximately 2Hz, then a fatal error has been detected and the system has halted. Buttons ======= B1 USER: the user button is connected to the I/O PC13 (pin 2) of the STM32 microcontroller. Serial Console ============== USART1 ------ Pins and Connectors: RXD: PA10 D3 CN9 pin 3, CN10 pin 33 PB7 CN7 pin 21 TXD: PA9 D8 CN5 pin 1, CN10 pin 21 PB6 D10 CN5 pin 3, CN10 pin 17 NOTE: You may need to edit the include/board.h to select different USART1 pin selections. TTL to RS-232 converter connection: Nucleo CN10 STM32F072RB ----------- ------------ Pin 21 PA9 USART1_TX *Warning you make need to reverse RX/TX on Pin 33 PA10 USART1_RX some RS-232 converters Pin 20 GND Pin 8 U5V To configure USART1 as the console: CONFIG_STM32_USART1=y CONFIG_USART1_SERIALDRIVER=y CONFIG_USART1_SERIAL_CONSOLE=y CONFIG_USART1_RXBUFSIZE=256 CONFIG_USART1_TXBUFSIZE=256 CONFIG_USART1_BAUD=115200 CONFIG_USART1_BITS=8 CONFIG_USART1_PARITY=0 CONFIG_USART1_2STOP=0 USART2 ------ Pins and Connectors: RXD: PA3 To be provided PA15 PD6 TXD: PA2 PA14 PD5 See "Virtual COM Port" and "RS-232 Shield" below. USART3 ------ Pins and Connectors: RXD: PB11 To be provided PC5 PC11 D9 TXD: PB10 PC4 PC10 D8 USART3 ------ Pins and Connectors: RXD: PA1 To be provided PC11 TXD: PA0 PC10 Virtual COM Port ---------------- Yet another option is to use UART2 and the USB virtual COM port. This option may be more convenient for long term development, but is painful to use during board bring-up. Solder Bridges. This configuration requires: - SB62 and SB63 Open: PA2 and PA3 on STM32 MCU are disconnected to D1 and D0 (pin 7 and pin 8) on Arduino connector CN9 and ST Morpho connector CN10. - SB13 and SB14 Closed: PA2 and PA3 on STM32F103C8T6 (ST-LINK MCU) are connected to PA3 and PA2 on STM32 MCU to have USART communication between them. Thus SB61, SB62 and SB63 should be OFF. Configuring USART2 is the same as given above. 115200 8N1 BAUD should be configure to interface with the Virtual COM port. Default ------- As shipped, SB62 and SB63 are open and SB13 and SB14 closed, so the virtual COM port is enabled. RS-232 Shield ------------- Supports a single RS-232 connected via Nucleo STM32F4x1RE Shield --------- --------------- -------- CN9 Pin 1 PA3 USART2_RXD RXD CN9 Pin 2 PA2 USART2_TXD TXD Support for this shield is enabled by selecting USART2 and configuring SB13, 14, 62, and 63 as described above under "Virtual COM Port" Configurations ============== Information Common to All Configurations ---------------------------------------- Each configuration is maintained in a sub-directory and can be selected as follow: tools/configure.sh nucleo-f072rb:<subdir> Before building, make sure the PATH environment variable includes the correct path to the directory than holds your toolchain binaries. And then build NuttX by simply typing the following. At the conclusion of the make, the nuttx binary will reside in an ELF file called, simply, nuttx. make oldconfig make The <subdir> that is provided above as an argument to the tools/configure.sh must be is one of the following. NOTES: 1. These configurations use the mconf-based configuration tool. To change any of these configurations using that tool, you should: a. Build and install the kconfig-mconf tool. See nuttx/README.txt see additional README.txt files in the NuttX tools repository. b. Execute 'make menuconfig' in nuttx/ in order to start the reconfiguration process. 2. Unless stated otherwise, all configurations generate console output on USART2, as described above under "Serial Console". The elevant configuration settings are listed below: CONFIG_STM32_USART2=y CONFIG_STM32_USART2_SERIALDRIVER=y CONFIG_STM32_USART=y CONFIG_USART2_SERIALDRIVER=y CONFIG_USART2_SERIAL_CONSOLE=y CONFIG_USART2_RXBUFSIZE=256 CONFIG_USART2_TXBUFSIZE=256 CONFIG_USART2_BAUD=115200 CONFIG_USART2_BITS=8 CONFIG_USART2_PARITY=0 CONFIG_USART2_2STOP=0 3. All of these configurations are set up to build under Linux using the "GNU Tools for ARM Embedded Processors" that is maintained by ARM (unless stated otherwise in the description of the configuration). https://developer.arm.com/open-source/gnu-toolchain/gnu-rm That toolchain selection can easily be reconfigured using 'make menuconfig'. Here are the relevant current settings: Build Setup: CONFIG_HOST_LINUX=y : Linux environment System Type -> Toolchain: CONFIG_ARMV7M_TOOLCHAIN_GNU_EABIL=y : GNU ARM EABI toolchain Configuration sub-directories ----------------------------- nsh: Configures the NuttShell (nsh) located at examples/nsh. This configuration is focused on low level, command-line driver testing. NOTES: 1. This initial release of this configuration was very minimal, but also very small: $ size nuttx text data bss dec hex filename 32000 92 1172 33264 81f0 nuttx The current version, additional features have been enabled: board bring-up initialization, button support, the procfs file system, and NSH built-in application support. The size increased as follows: $ size nuttx text data bss dec hex filename 40231 92 1208 41531 a23b nuttx Those additional features cost about 8KiB FLASH. I believe that is a good use of the STM32F072RB's FLASH, but if you interested in the more minimal configuration, here is what was changed: Removed CONFIG_BINFMT_DISABLE=y CONFIG_DISABLE_MOUNTPOINT=y CONFIG_NSH_DISABLE_CD=y Added: CONFIG_ARCH_BUTTONS=y CONFIG_ARCH_IRQBUTTONS=y CONFIG_BUILTIN=y CONFIG_FS_PROCFS=y CONFIG_NSH_PROC_MOUNTPOINT="/proc" CONFIG_LIB_BOARDCTL=y CONFIG_NSH_ARCHINIT=y CONFIG_NSH_BUILTIN_APPS=y Support for NSH built-in applications is enabled for future use. However, no built applications are enabled in this base configuration. 2. C++ support for applications is NOT enabled. That could be enabled with the following configuration changes: CONFIG_HAVE_CXX=y CONFIG_HAVE_CXXINITIALIZE=y And also support for C++ constructors under apps/platform.