sergiotarxz/nuttx
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
7d8f6625e3
nuttx/configs/freedom-k28f/include/board.h

463 lines
19 KiB
C
Raw Blame History

This file contains ambiguous Unicode characters

This file contains Unicode characters that might be confused with other characters. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.

/************************************************************************************
* configs/freedom-k28f/include/board.h
*
* Copyright (C) 2018 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
************************************************************************************/
#ifndef __CONFIGS_FREEDOM_K28F_INCLUDE_BOARD_H
#define __CONFIGS_FREEDOM_K28F_INCLUDE_BOARD_H
/************************************************************************************
* Included Files
************************************************************************************/
#include <nuttx/config.h>
#ifndef __ASSEMBLY__
# include <stdint.h>
# include <stdbool.h>
# include <arch/chip/kinetis_mcg.h>
#endif
/************************************************************************************
* Pre-processor Definitions
************************************************************************************/
/* Clocking *************************************************************************/
/* The Freedom K28F uses a 12MHz external Oscillator. The Kinetis MCU startup from an
* internal digitally-controlled oscillator (DCO). Nuttx will enable the main external
* oscillator (EXTAL0/XTAL0). The external oscillator/resonator can range from
* 32.768 KHz up to 50 MHz. The default external source for the MCG oscillator inputs
* is 12 MHz oscillator
*
* X501 a High-frequency, low-power Xtal
*/
#define BOARD_EXTAL_LP 1
#define BOARD_EXTAL_FREQ 12000000 /* 12MHz Oscillator */
#define BOARD_XTAL32_FREQ 32768 /* 32KHz RTC Oscillator */
/* PLL Configuration. Either the external clock or crystal frequency is used to
* select the PRDIV value. Only reference clock frequencies are supported that will
* produce a KINETIS_MCG_PLL_REF_MIN >= PLLIN <=KINETIS_MCG_PLL_REF_MAX reference
* clock to the PLL.
*
* PLL Input frequency: PLLIN = REFCLK / PRDIV = 12 MHz / 1 = 12 MHz
* PLL Output frequency: PLLOUT = PLLIN * VDIV = 12 MHz * 25 = 300 MHz
* MCG Frequency: PLLOUT = 150 MHz = 300 MHz / KINETIS_MCG_PLL_INTERNAL_DIVBY
*
* PRDIV register value is the divider minus KINETIS_MCG_C5_PRDIV_BASE.
* VDIV register value is offset by KINETIS_MCG_C6_VDIV_BASE.
*/
#define BOARD_PRDIV 1 /* PLL External Reference Divider */
#define BOARD_VDIV 25 /* PLL VCO Divider (frequency multiplier) */
/* Define additional MCG_C2 Setting */
#define BOARD_MCG_C2_FCFTRIM 0 /* Do not enable FCFTRIM */
#define BOARD_MCG_C2_LOCRE0 MCG_C2_LOCRE0 /* Enable reset on loss of clock */
#define BOARD_PLLIN_FREQ (BOARD_EXTAL_FREQ / BOARD_PRDIV)
#define BOARD_PLLOUT_FREQ (BOARD_PLLIN_FREQ * BOARD_VDIV)
#define BOARD_MCG_FREQ (BOARD_PLLOUT_FREQ / KINETIS_MCG_PLL_INTERNAL_DIVBY)
/* SIM CLKDIV1 dividers */
#define BOARD_OUTDIV1 1 /* Core = MCG, 180 MHz */
#define BOARD_OUTDIV2 3 /* Bus = MCG / 3, 60 MHz */
#define BOARD_OUTDIV3 3 /* FlexBus = MCG / 3, 60 MHz */
#define BOARD_OUTDIV4 7 /* Flash clock = MCG / 7, 25.7 MHz */
#define BOARD_CORECLK_FREQ (BOARD_MCG_FREQ / BOARD_OUTDIV1)
#define BOARD_BUS_FREQ (BOARD_MCG_FREQ / BOARD_OUTDIV2)
#define BOARD_FLEXBUS_FREQ (BOARD_MCG_FREQ / BOARD_OUTDIV3)
#define BOARD_FLASHCLK_FREQ (BOARD_MCG_FREQ / BOARD_OUTDIV4)
/* Use BOARD_MCG_FREQ as the output SIM_SOPT2 MUX selected by
* SIM_SOPT2[PLLFLLSEL]
*/
#define BOARD_SOPT2_PLLFLLSEL SIM_SOPT2_PLLFLLSEL_MCGPLLCLK
#define BOARD_SOPT2_FREQ BOARD_MCG_FREQ
/* N.B. The above BOARD_SOPT2_FREQ precludes use of USB with a 12 MHz Xtal
* Divider output clock = Divider input clock × [ (USBFRAC+1) / (USBDIV+1) ]
* SIM_CLKDIV2_FREQ = BOARD_SOPT2_FREQ × [ (USBFRAC+1) / (USBDIV+1) ]
* 48MHz = 168MHz X [(1 + 1) / (6 + 1)]
* 48MHz = 168MHz / (6 + 1) * (1 + 1)
*/
#if (BOARD_MCG_FREQ == 168000000L)
# define BOARD_SIM_CLKDIV2_USBFRAC 2
# define BOARD_SIM_CLKDIV2_USBDIV 7
# define BOARD_SIM_CLKDIV2_FREQ (BOARD_SOPT2_FREQ / \
BOARD_SIM_CLKDIV2_USBDIV * \
BOARD_SIM_CLKDIV2_USBFRAC)
#endif
/* Divider output clock = Divider input clock * ((PLLFLLFRAC+1)/(PLLFLLDIV+1))
* SIM_CLKDIV3_FREQ = BOARD_SOPT2_FREQ × [ (PLLFLLFRAC+1) / (PLLFLLDIV+1)]
* 90 MHz = 180 MHz X [(0 + 1) / (1 + 1)]
* 90 MHz = 180 MHz / (1 + 1) * (0 + 1)
*/
#define BOARD_SIM_CLKDIV3_PLLFLLFRAC 1
#define BOARD_SIM_CLKDIV3_PLLFLLDIV 2
#define BOARD_SIM_CLKDIV3_FREQ (BOARD_SOPT2_FREQ / \
BOARD_SIM_CLKDIV3_PLLFLLDIV * \
BOARD_SIM_CLKDIV3_PLLFLLFRAC)
#define BOARD_LPUART0_CLKSRC SIM_SOPT2_LPUARTSRC_MCGCLK
#define BOARD_LPUART0_FREQ BOARD_SIM_CLKDIV3_FREQ
#define BOARD_TPM_CLKSRC SIM_SOPT2_TPMSRC_MCGCLK
#define BOARD_TPM_FREQ BOARD_SIM_CLKDIV3_FREQ
/* SDHC clocking ********************************************************************/
/* SDCLK configurations corresponding to various modes of operation. Formula is:
*
* SDCLK frequency = (base clock) / (prescaler * divisor)
*
* The SDHC module is always configure configured so that the core clock is the base
* clock. Possible values for prescaler and divisor are:
*
* SDCLKFS: {2, 4, 8, 16, 32, 63, 128, 256}
* DVS: {1..16}
*/
/* Identification mode: Optimal 400KHz, Actual 180MHz / (32 * 15) = 375 Khz */
#define BOARD_SDHC_IDMODE_PRESCALER SDHC_SYSCTL_SDCLKFS_DIV32
#define BOARD_SDHC_IDMODE_DIVISOR SDHC_SYSCTL_DVS_DIV(15)
/* MMC normal mode: Optimal 20MHz, Actual 180MHz / (2 * 5) = 18 MHz */
#define BOARD_SDHC_MMCMODE_PRESCALER SDHC_SYSCTL_SDCLKFS_DIV2
#define BOARD_SDHC_MMCMODE_DIVISOR SDHC_SYSCTL_DVS_DIV(5)
/* SD normal mode (1-bit): Optimal 20MHz, Actual 180MHz / (2 * 5) = 18 MHz */
#define BOARD_SDHC_SD1MODE_PRESCALER SDHC_SYSCTL_SDCLKFS_DIV2
#define BOARD_SDHC_SD1MODE_DIVISOR SDHC_SYSCTL_DVS_DIV(5)
/* SD normal mode (4-bit): Optimal 25MHz, Actual 180MHz / (2 * 4) = 22.5 MHz (with DMA)
* SD normal mode (4-bit): Optimal 20MHz, Actual 180MHz / (2 * 4) = 22.5 MHz (no DMA)
*/
#ifdef CONFIG_SDIO_DMA
# define BOARD_SDHC_SD4MODE_PRESCALER SDHC_SYSCTL_SDCLKFS_DIV2
# define BOARD_SDHC_SD4MODE_DIVISOR SDHC_SYSCTL_DVS_DIV(4)
#else
# define BOARD_SDHC_SD4MODE_PRESCALER SDHC_SYSCTL_SDCLKFS_DIV2
# define BOARD_SDHC_SD4MODE_DIVISOR SDHC_SYSCTL_DVS_DIV(4)
#endif
/* Use the output of SIM_SOPT2[PLLFLLSEL] as the USB clock source */
#define BOARD_USB_CLKSRC SIM_SOPT2_USBSRC
#define BOARD_USB_FREQ BOARD_SIM_CLKDIV2_FREQ
/* Allow USBOTG-FS Controller to Read from FLASH */
#define BOARD_USB_FLASHACCESS
/* PWM Configuration */
/* FTM0 Channels */
#define GPIO_FTM0_CH0OUT PIN_FTM0_CH0_2 /* Pin 22: PTC1 */
#define GPIO_FTM0_CH1OUT PIN_FTM0_CH1_2 /* Pin 23: PTC2 */
#define GPIO_FTM0_CH2OUT PIN_FTM0_CH2_2 /* Pin 9: PTC3 */
#define GPIO_FTM0_CH3OUT PIN_FTM0_CH3 /* Pin 10: PTC4 */
#define GPIO_FTM0_CH4OUT PIN_FTM0_CH4 /* Pin 6: PTD4 */
#define GPIO_FTM0_CH5OUT PIN_FTM0_CH5_2 /* Pin 20: PTD5 */
#define GPIO_FTM0_CH6OUT PIN_FTM0_CH6_2 /* Pin 21: PTD6 */
#define GPIO_FTM0_CH7OUT PIN_FTM0_CH7_2 /* Pin 5: PTD7 */
/* FTM1 Channels */
#define GPIO_FTM1_CH0OUT PIN_FTM1_CH0_1 /* Pin 3: PTA12 */
#define GPIO_FTM1_CH1OUT PIN_FTM1_CH1_1 /* Pin 4: PTA13 */
/* FTM2 Channels */
#define GPIO_FTM2_CH0OUT PIN_FTM2_CH0 /* Pin 25: PTB18 */
#define GPIO_FTM2_CH1OUT PIN_FTM2_CH1 /* Pin 32: PTB19 */
/* LED definitions ******************************************************************/
/* A single LED is available driven by PTC5. The LED is grounded so bringing PTC5
* high will illuminate the LED.
*/
/* LED index values for use with board_userled() */
#define BOARD_LED 0
#define BOARD_NLEDS 1
/* LED bits for use with board_userled_all() */
#define BOARD_LED_BIT (1 << BOARD_LED)
/* When CONFIG_ARCH_LEDS is defined in the NuttX configuration, NuttX will
* control the LED as defined below. Thus if the LED is statically on, NuttX has
* successfully booted and is, apparently, running normally. If the LED is
* flashing at approximately 2Hz, then a fatal error has been detected and the
* system has halted.
*/
#define LED_STARTED 0 /* STATUS LED=OFF */
#define LED_HEAPALLOCATE 0 /* STATUS LED=OFF */
#define LED_IRQSENABLED 0 /* STATUS LED=OFF */
#define LED_STACKCREATED 1 /* STATUS LED=ON */
#define LED_INIRQ 2 /* STATUS LED=no change */
#define LED_SIGNAL 2 /* STATUS LED=no change */
#define LED_ASSERTION 3 /* STATUS LED=no change */
#define LED_PANIC 3 /* STATUS LED=flashing */
/* Button definitions ***************************************************************/
/* The freedom-k28f board has no standard GPIO contact buttons */
/* Alternative pin resolution *******************************************************/
/* The Freedom K28F has five LPUARTs with pin availability as follows:
*
* ----- --------------- -------------------------------
* GPIO LPUART FUNCTION BOARD CONFIGURATION
* ----- --------------- -------------------------------
* PTA1 LPUART0_RX PTA1 GPIO0
* PTA15 LPUART0_RX PTA15 FXIO0_D21
* PTB14 LPUART0_RX PTB14
* PTB16 LPUART0_RX PTB16 SDRAM_D17
* PTC25 LPUART0_RX PTC25 LPUART0_RX_TGTMCU
* PTD6 LPUART0_RX PTD6 Arduino_D17_ADC0_SE7b
* PTA2 LPUART0_TX PTA2 INT
* PTA14 LPUART0_TX PTA14 FXIO0_D20
* PTB15 LPUART0_TX N/C
* PTB17 LPUART0_TX PTB17 SDRAM_D16
* PTC24 LPUART0_TX PTC24 LPUART0_TX_TGTMCU
* PTD7 LPUART0_TX PTD7 SDRAM_CKE
* PTA3 LPUART0_RTS PTA3
* PTA17 LPUART0_RTS PTA17 FXIO0_D23
* PTB2 LPUART0_RTS PTB2 Arduino_D19_ADC0_SE12/I2C0_SCL/SDRAM_WE
* PTB12 LPUART0_RTS PTB12 Arduino_D5_FTM1_CH0/FTM0_CH4
* PTC27 LPUART0_RTS PTC27 FXOS8700CQ_RESET
* PTD4 LPUART0_RTS PTD4 SDRAM_A10
* PTA0 LPUART0_CTS PTA0 K28F_SWD_CLK
* PTA16 LPUART0_CTS PTA16 FXIO0_D22
* PTB3 LPUART0_CTS PTB3 Arduino_D18_ADC0_SE13/I2C0_SDA/SDRAM_CS0
* PTB13 LPUART0_CTS PTB13 Arduino_D6_FTM1_CH1/FTM0_CH5
* PTC26 LPUART0_CTS PTC26 FXOS8700CQ_INT
* PTD5 LPUART0_CTS PTD5 SDRAM_A9
* ----- --------------- -------------------------------
* PTD8 LPUART1_RX PTD8 FXIO0_D24
* PTC3 LPUART1_RX PTC3 CLKOUT
* PTE1 LPUART1_RX PTE1 QSPIA0_SCLK
* PTC4 LPUART1_TX PTC4 SDRAM_A19
* PTD9 LPUART1_TX PTD9 FXIO0_D25
* PTE0 LPUART1_TX PTE0 QSPIA0_DATA3
* PTD10 LPUART1_RTS PTD10 FXIO0_D26
* PTC1 LPUART1_RTS PTC1 SDRAM_A21
* PTE3 LPUART1_RTS PTE3 QSPIA0_DATA2
* PTC2 LPUART1_CTS PTC1 SDRAM_A21
* PTD11 LPUART1_CTS PTD11 FXIO0_D27
* PTE2 LPUART1_CTS PTE2 QSPIA0_DATA0
* ----- --------------- -------------------------------
* PTA25 LPUART2_RX PTA25 SDHC0_D0/Arduino_D0_LPUART2_RX
* PTD2 LPUART2_RX PTD2 SDRAM_A12
* PTE13 LPUART2_RX N/C
* PTE17 LPUART2_RX N/C
* PTA24 LPUART2_TX PTA24 SDHC0_D1/Arduino_D1_LPUART2_TX
* PTD3 LPUART2_TX PTD3 SDRAM_A11
* PTE12 LPUART2_TX PTE12 I2S0_TX_BCLK
* PTE16 LPUART2_TX N/C
* PTD0 LPUART2_RTS PTD0 Button_LLWU_P12
* PTA27 LPUART2_RTS PTA27 SDHC0_CMD
* PTE19 LPUART2_RTS N/C
* PTA26 LPUART2_CTS PTA26 SDHC0_DCLK
* PTD1 LPUART2_CTS PTD1 Arduino_D16_ADC0_SE5b
* PTE18 LPUART2_CTS N/C
* ----- --------------- -------------------------------
* PTA29 LPUART3_RX PTA29 SDHC0_D2
* PTB10 LPUART3_RX PTB10 SDRAM_D19
* PTC16 LPUART3_RX PTC16 SDRAM_DQM2
* PTE5 LPUART3_RX PTE5 QSPIA0_SS0/USB0_SOF_OUT
* PTA28 LPUART3_TX PTA28 SDHC0_D3
* PTB11 LPUART3_TX PTB11 SDRAM_D18
* PTC17 LPUART3_TX PTC17 SDRAM_DQM3
* PTE4 LPUART3_TX PTE4 QSPIA0_DATA1
* PTB8 LPUART3_RTS PTB8 SDRAM_D21
* PTA31 LPUART3_RTS PTA31
* PTC18 LPUART3_RTS PTC18 Arduino_D7
* PTE7 LPUART3_RTS PTE7 I2S0_RXD0/LEDRGB_GREEN
* PTA30 LPUART3_CTS PTA30
* PTB9 LPUART3_CTS PTB9 SDRAM_D20
* PTC19 LPUART3_CTS PTC19 Arduino_D8
* PTE6 LPUART3_CTS PTE6 I2S0_MCK/LEDRGB_RED
* ----- --------------- -------------------------------
* PTA21 LPUART4_RX PTA21 TE/FXIO0_D9
* PTC14 LPUART4_RX PTC14 SDRAM_D25
* PTE21 LPUART4_RX N/C
* PTA20 LPUART4_TX PTA20 RD/FXIO0_D8
* PTC15 LPUART4_TX PTC15 SDRAM_D24
* PTE20 LPUART4_TX N/C
* PTA23 LPUART4_RTS PTA23 WR/FXIO0_D7
* PTC12 LPUART4_RTS PTC12 SDRAM_D27
* PTE23 LPUART4_RTS N/C
* PTA22 LPUART4_CTS PTA22 CS/FXIO0_D6
* PTC13 LPUART4_CTS PTC13 SDRAM_D26
* PTE22 LPUART4_CTS N/C
* ----- --------------- -------------------------------
*
* Virtual serial port
* -------------------
*
* A serial port connection is available between the OpenSDA v2.2 MCU and
* pins PTC24 and PTC25 of the K28 MCU:
*
* ----- --------------- -------------------------------
* GPIO LPUART FUNCTION BOARD CONFIGURATION
* ----- --------------- -------------------------------
* PTC25 LPUART0_RX PTC25 LPUART0_RX_TGTMCU
* PTC24 LPUART0_TX PTC24 LPUART0_TX_TGTMCU
* ----- --------------- -------------------------------
*/
#define PIN_LPUART0_RX PIN_LPUART0_RX_5 /* PTC25 */
#define PIN_LPUART0_TX PIN_LPUART0_TX_5 /* PTC24
/* Arduino RS-232 Shield
* ---------------------
*
* ----- --------------- -------------------------------
* GPIO LPUART FUNCTION BOARD CONFIGURATION
* ----- --------------- -------------------------------
* PTA25 LPUART2_RX PTA25 SDHC0_D0/Arduino_D0_LPUART2_RX
* PTA24 LPUART2_TX PTA24 SDHC0_D1/Arduino_D1_LPUART2_TX
* ----- --------------- -------------------------------
*
* Note: PTA24 and PTA25 are shared between Micro SD Card circuit and
* Arduino connectors. Remove R106 and R107 or R94 and R11 as necessary to
* prevent contention.
*/
#define PIN_LPUART2_RX PIN_LPUART2_RX_1 /* PTA25 */
#define PIN_LPUART2_TX PIN_LPUART2_TX_1 /* PTA24 */
/* I2C */
#ifdef CONFIG_KINETIS_I2C0
#ifdef CONFIG_FREEDOM_K28F_I2C_ALT_PINS
# define PIN_I2C0_SCL (PIN_I2C0_SCL_1 | PIN_ALT2_OPENDRAIN | PIN_ALT2_SLOW)
# define PIN_I2C0_SDA (PIN_I2C0_SDA_1 | PIN_ALT2_OPENDRAIN | PIN_ALT2_SLOW)
#else
# define PIN_I2C0_SCL (PIN_I2C0_SCL_2 | PIN_ALT2_OPENDRAIN | PIN_ALT2_SLOW)
# define PIN_I2C0_SDA (PIN_I2C0_SDA_2 | PIN_ALT2_OPENDRAIN | PIN_ALT2_SLOW)
#endif
#endif
/* REVISIT: Added only for clean compilation with I2C1 enabled. */
#ifdef CONFIG_KINETIS_I2C1
#ifdef CONFIG_FREEDOM_K28F_I2C_ALT_PINS
# define PIN_I2C1_SCL (PIN_I2C1_SCL_1 | PIN_ALT2_OPENDRAIN | PIN_ALT2_SLOW)
# define PIN_I2C1_SDA (PIN_I2C1_SDA_1 | PIN_ALT2_OPENDRAIN | PIN_ALT2_SLOW)
#else
# define PIN_I2C1_SCL (PIN_I2C1_SCL_2 | PIN_ALT2_OPENDRAIN | PIN_ALT2_SLOW)
# define PIN_I2C1_SDA (PIN_I2C1_SDA_2 | PIN_ALT2_OPENDRAIN | PIN_ALT2_SLOW)
#endif
#endif
/* LED definitions ******************************************************************/
/* The Freedom K28F has a single RGB LED driven by the K28F as follows:
*
* LED K28
* ------ -------------------------------------------------------
* RED PTE6
* BLUE PTE7
* GREEN PTE8
*
* If CONFIG_ARCH_LEDS is not defined, then the user can control the LEDs in any
* way. The following definitions are used to access individual LEDs.
*/
/* LED index values for use with board_userled() */
#define BOARD_LED_R 0
#define BOARD_LED_G 1
#define BOARD_LED_B 2
#define BOARD_NLEDS 3
/* LED bits for use with board_userled_all() */
#define BOARD_LED_R_BIT (1 << BOARD_LED_R)
#define BOARD_LED_G_BIT (1 << BOARD_LED_G)
#define BOARD_LED_B_BIT (1 << BOARD_LED_B)
/* If CONFIG_ARCH_LEDs is defined, then NuttX will control the LED on board
* the Freedom K28F. The following definitions describe how NuttX controls
* the LEDs:
*
* SYMBOL Meaning LED state
* RED GREEN BLUE
* ------------------- ---------------------------- ----------------- */
#define LED_STARTED 1 /* NuttX has been started OFF OFF OFF */
#define LED_HEAPALLOCATE 2 /* Heap has been allocated OFF OFF ON */
#define LED_IRQSENABLED 0 /* Interrupts enabled OFF OFF ON */
#define LED_STACKCREATED 3 /* Idle stack created OFF ON OFF */
#define LED_INIRQ 0 /* In an interrupt (no change) */
#define LED_SIGNAL 0 /* In a signal handler (no change) */
#define LED_ASSERTION 0 /* An assertion failed (no change) */
#define LED_PANIC 4 /* The system has crashed FLASH OFF OFF */
#undef LED_IDLE /* K28 is in sleep mode (Not used) */
/* Button definitions ***************************************************************/
/* Two push buttons, SW2 and SW3, are available on FRDM-K28F board, where SW2 is
* connected to PTA4 and SW3 is connected to PTD0. Besides the general purpose
* input/output functions, SW2 and SW3 can be low-power wake up signal. Also, only
* SW3 can be a non-maskable interrupt.
*
* Switch GPIO Function
* --------- ---------------------------------------------------------------
* SW2 PTA4/NMI_B
* SW3 PTA4/NMI_B
*/
#define BUTTON_SW2 0
#define BUTTON_SW3 1
#define NUM_BUTTONS 2
#define BUTTON_SW2_BIT (1 << BUTTON_SW2)
#define BUTTON_SW3_BIT (1 << BUTTON_SW3)
#endif /* __CONFIGS_FREEDOM_K28F_INCLUDE_BOARD_H */
Reference in New Issue View Git Blame Copy Permalink