302 lines
8.4 KiB
Plaintext
302 lines
8.4 KiB
Plaintext
#
|
|
# For a description of the syntax of this configuration file,
|
|
# see the file kconfig-language.txt in the NuttX tools repository.
|
|
#
|
|
|
|
config ARCH_HAVE_NET
|
|
bool
|
|
default n
|
|
|
|
config ARCH_HAVE_PHY
|
|
bool
|
|
default n
|
|
|
|
config NET
|
|
bool "Networking support"
|
|
default n
|
|
select ARCH_HAVE_NET
|
|
---help---
|
|
Enable or disable all network features
|
|
|
|
if NET
|
|
|
|
config NET_NOINTS
|
|
bool "Not interrupt driven"
|
|
default n
|
|
---help---
|
|
NET_NOINT indicates that network layer is not called from the
|
|
interrupt level. If NET_NOINTS is defined, critical sections
|
|
will be managed with semaphores; Otherwise, it assumed that
|
|
network layer will be called from interrupt level handling
|
|
and critical sections will be managed by enabling and disabling
|
|
interrupts.
|
|
|
|
config NET_PROMISCUOUS
|
|
bool "Promiscuous mode"
|
|
default n
|
|
---help---
|
|
Force the Ethernet driver to operate in promiscuous mode (if supported
|
|
by the Ethernet driver).
|
|
|
|
menu "Driver buffer configuration"
|
|
|
|
config NET_MULTIBUFFER
|
|
bool "Use multiple device-side I/O buffers"
|
|
default n
|
|
---help---
|
|
Traditionally, the uIP stacl has used a single buffer for all
|
|
incoming and outgoing traffic. If this configuration is selected,
|
|
then the driver can manage multiple I/O buffers and can, for
|
|
example, be filling one input buffer while sending another output
|
|
buffer. Or, as another example, the driver may support queuing of
|
|
concurrent input/ouput and output transfers for better performance.
|
|
|
|
config NET_ETH_MTU
|
|
int "Ethernet packet buffer size (MTU)"
|
|
default 1294 if NET_IPv6
|
|
default 590 if !NET_IPv6
|
|
depends on NET_ETHERNET
|
|
range 590 1518
|
|
---help---
|
|
Packet buffer size. This size includes the TCP/UDP payload plus the
|
|
size of TCP/UDP header, the IP header, and the Ethernet header.
|
|
This value is normally referred to as the MTU (Maximum Transmission
|
|
Unit); the payload is the MSS (Maximum Segment Size).
|
|
|
|
IPv4 hosts are required to be able to handle an MSS of at least
|
|
536 octets, resulting in a minimum buffer size of 536+20+20+14 =
|
|
590.
|
|
|
|
IPv6 hosts are required to be able to handle an MSS of 1220 octets,
|
|
resulting in a minimum buffer size of of 1220+20+40+14 = 1294
|
|
|
|
config NET_ETH_TCP_RECVWNDO
|
|
int "Ethernet TCP receive window size"
|
|
default 1220 if NET_IPv6
|
|
default 536 if !NET_IPv6
|
|
depends on NET_ETHERNET && NET_TCP
|
|
---help---
|
|
The size of the advertised receiver's window. Should be set low
|
|
(i.e., to the size of the MSS) if the application is slow to process
|
|
incoming data, or high (32768 bytes) if the application processes
|
|
data quickly.
|
|
|
|
config NET_SLIP_MTU
|
|
int # "SLIP packet buffer size (MTU)"
|
|
default 296
|
|
depends on NET_SLIP
|
|
range 296 1518
|
|
---help---
|
|
Provides the size of the SLIP packet buffers. This size includes
|
|
the TCP/UDP payload plus the size of TCP/UDP header and the IP header.
|
|
This value is normally referred to as the MTU (Maximum Transmission Unit);
|
|
the payload payload is the MSS (Maximum Segment Size).
|
|
|
|
SLIP is required to support at lest 256+20+20 = 296. Values other than
|
|
296 are not recommended.
|
|
|
|
The Linux slip module hard-codes its MTU size to 296 (40 bytes for
|
|
the IP+TPC headers plus 256 bytes of data). So you might as well
|
|
set CONFIG_NET_SLIP_MTU to 296 as well.
|
|
|
|
There may be an issue with this setting, however. I see that Linux
|
|
uses a MTU of 296 and window of 256, but actually only sends 168
|
|
bytes of data: 40 + 128. I believe that is to allow for the 2x
|
|
worst cast packet expansion. Ideally we would like to advertise the
|
|
256 MSS, but restrict transfers to 128 bytes (possibly by modifying
|
|
the MSS value in the TCP connection structure).
|
|
|
|
|
|
config NET_SLIP_TCP_RECVWNDO
|
|
int "SLIP TCP receive window size"
|
|
default 256
|
|
depends on NET_SLIP && NET_TCP
|
|
---help---
|
|
The size of the advertised receiver's window. Should be set low
|
|
(i.e., to the size of the MSS) if the application is slow to process
|
|
incoming data, or high (32768 bytes) if the application processes
|
|
data quickly.
|
|
|
|
config NET_TUN_MTU
|
|
int "TUN packet buffer size (MTU)"
|
|
default 296
|
|
depends on NET_TUN
|
|
range 296 1518
|
|
|
|
config NET_TUN_TCP_RECVWNDO
|
|
int "TUN TCP receive window size"
|
|
default 256
|
|
depends on NET_TUN && NET_TCP
|
|
|
|
config NET_GUARDSIZE
|
|
int "Driver I/O guard size"
|
|
default 2
|
|
---help---
|
|
Network drivers often receive packets with garbage at the end and
|
|
are longer than the size of packet in the TCP header. The following
|
|
"fudge" factor increases the size of the I/O buffering by a small
|
|
amount to allocate slightly oversize packets. After receipt, the
|
|
packet size will be chopped down to the size indicated in the TCP
|
|
header.
|
|
|
|
endmenu # Driver buffer configuration
|
|
|
|
menu "Data link support"
|
|
|
|
config NET_MULTILINK
|
|
bool
|
|
default n
|
|
|
|
config NET_USER_DEVFMT
|
|
bool "User provided devfmt"
|
|
default n
|
|
depends on EXPERIMENTAL
|
|
---help---
|
|
netdev_register will get devfmt form d_ifname if it is initialized.
|
|
|
|
config NET_ETHERNET
|
|
bool "Ethernet support"
|
|
default y if !NET_SLIP
|
|
default n if NET_SLIP
|
|
select NETDEV_MULTINIC if NET_LOOPBACK || NET_SLIP || NET_TUN
|
|
select NET_MULTILINK if NET_LOOPBACK || NET_SLIP || NET_TUN
|
|
---help---
|
|
If NET_SLIP is not selected, then Ethernet will be used (there is
|
|
no need to define anything special in the configuration file to use
|
|
Ethernet -- it is the default).
|
|
|
|
config NET_LOOPBACK
|
|
bool "Local loopback"
|
|
default n
|
|
select NETDEV_MULTINIC if NET_ETHERNET || NET_SLIP || NET_TUN
|
|
select NET_MULTILINK if NET_ETHERNET || NET_SLIP || NET_TUN
|
|
---help---
|
|
Add support for the local network loopback device, lo. Any additional
|
|
networking devices that are enabled must be compatible with
|
|
CONFIG_NET_NOINTS.
|
|
|
|
config NET_SLIP
|
|
bool "SLIP support"
|
|
default n
|
|
select NETDEV_MULTINIC if NET_ETHERNET || NET_LOOPBACK || NET_TUN
|
|
select NET_MULTILINK if NET_ETHERNET || NET_LOOPBACK || NET_TUN
|
|
---help---
|
|
Enables building of the SLIP driver. SLIP requires
|
|
at least one IP protocol selected and the following additional
|
|
network settings: NET_NOINTS and NET_MULTIBUFFER.
|
|
|
|
SLIP supports point-to-point IP communications over a serial port.
|
|
The default data link layer for network layer is Ethernet. If
|
|
NET_SLIP is defined in the NuttX configuration file, then SLIP will
|
|
be supported. The basic differences between the SLIP and Ethernet
|
|
configurations is that when SLIP is selected:
|
|
|
|
* The link level header (that comes before the IP header) is omitted.
|
|
* All MAC address processing is suppressed.
|
|
* ARP is disabled.
|
|
|
|
If NET_SLIP is not selected, then Ethernet will be used (there is
|
|
no need to define anything special in the configuration file to use
|
|
Ethernet -- it is the default).
|
|
|
|
if NET_SLIP
|
|
|
|
config SLIP_NINTERFACES
|
|
int "Number of SLIP interfaces"
|
|
default 1
|
|
---help---
|
|
Selects the number of physical SLIP
|
|
interfaces to support.
|
|
Default: 1
|
|
|
|
config SLIP_STACKSIZE
|
|
int "SLIP stack size"
|
|
default 2048
|
|
---help---
|
|
Select the stack size of the SLIP RX and TX tasks. Default: 2048
|
|
|
|
config SLIP_DEFPRIO
|
|
int "SLIP priority"
|
|
default 128
|
|
---help---
|
|
The priority of the SLIP RX and TX tasks. Default: 128
|
|
|
|
endif # NET_SLIP
|
|
|
|
config NET_TUN
|
|
bool "TUN Virtual Network Device support"
|
|
default n
|
|
select NETDEV_MULTINIC if NET_ETHERNET || NET_LOOPBACK || NET_SLIP
|
|
select NET_MULTILINK if NET_ETHERNET || NET_LOOPBACK || NET_SLIP
|
|
select ARCH_HAVE_NETDEV_STATISTICS
|
|
|
|
if NET_TUN
|
|
|
|
config TUN_NINTERFACES
|
|
int "Number of TUN interfaces"
|
|
default 1
|
|
range 1 8
|
|
---help---
|
|
Selects the number of TUN
|
|
interfaces to support.
|
|
Default: 1
|
|
|
|
endif # NET_TUN
|
|
|
|
endmenu # Data link support
|
|
|
|
source "net/netdev/Kconfig"
|
|
|
|
menu "Internet Protocol Selection"
|
|
|
|
config NET_IPv4
|
|
bool "IPv4"
|
|
default y
|
|
---help---
|
|
Build in support for IPv4.
|
|
|
|
config NET_IPv6
|
|
bool "IPv6"
|
|
default n
|
|
---help---
|
|
Build in support for IPv6.
|
|
|
|
source "net/neighbor/Kconfig"
|
|
endmenu # Internet Protocol Selection
|
|
|
|
source "net/socket/Kconfig"
|
|
source "net/pkt/Kconfig"
|
|
source "net/local/Kconfig"
|
|
source "net/tcp/Kconfig"
|
|
source "net/udp/Kconfig"
|
|
source "net/icmp/Kconfig"
|
|
source "net/icmpv6/Kconfig"
|
|
source "net/igmp/Kconfig"
|
|
source "net/arp/Kconfig"
|
|
source "net/loopback/Kconfig"
|
|
source "net/iob/Kconfig"
|
|
source "net/procfs/Kconfig"
|
|
source "net/utils/Kconfig"
|
|
|
|
config NET_STATISTICS
|
|
bool "Collect network statistics"
|
|
default n
|
|
---help---
|
|
Network layer statistics on or off
|
|
|
|
source "net/route/Kconfig"
|
|
|
|
config NET_MULTICAST
|
|
bool "Multi-cast Tx support"
|
|
default n
|
|
---help---
|
|
Outgoing multi-cast address support
|
|
|
|
config NET_HOSTNAME
|
|
string "Host name for current machine"
|
|
default ""
|
|
---help---
|
|
A unique name to identify device on the network
|
|
|
|
endif # NET
|