217 lines
5.3 KiB
ReStructuredText
217 lines
5.3 KiB
ReStructuredText
=======================
|
||
Adafruit Feather RP2040
|
||
=======================
|
||
|
||
The Feather RP2040 is a general purpose RP2040 board supplied by
|
||
Adafruit.
|
||
|
||
.. figure:: Feather.png
|
||
:align: center
|
||
|
||
Features
|
||
========
|
||
|
||
* RP2040 microcontroller chip
|
||
* Dual-core ARM Cortex M0+ processor, flexible clock running up to 133 MHz
|
||
* 264kB of SRAM, and 8MB of on-board Flash memory
|
||
* Castellated module allows soldering direct to carrier boards
|
||
* USB Host and Device support via type C connector.
|
||
* Low-power sleep and dormant modes
|
||
* Drag & drop programming using mass storage over USB
|
||
* 26 multi-function GPIO pins
|
||
* 2× SPI, 2× I2C, 2× UART, 3× 12-bit ADC, 16× controllable PWM channels
|
||
* Accurate clock and timer on-chip
|
||
* Temperature sensor
|
||
* Accelerated floating point libraries on-chip
|
||
* 8 × Programmable IO (PIO) state machines for custom peripheral support
|
||
* LiPoly Battery connector
|
||
|
||
Serial Console
|
||
==============
|
||
|
||
By default a serial console appears on pins 14 (RX GPIO0) and pin 15
|
||
(TX GPIO1). This console runs a 115200-8N1.
|
||
|
||
The board can be configured to use the USB connection as the serial console.
|
||
|
||
Buttons and LEDs
|
||
================
|
||
|
||
User LED controlled by GPIO13.
|
||
|
||
A ws2812 (NeoPixel) smart RGB LED controlled by GPIO16.
|
||
|
||
An LED (CHG LED) that indicates the charging status of
|
||
connected LiPo cell.
|
||
|
||
There is a BOOT button which if held down when power is first
|
||
applied or the RESET button is pressed will cause the RP2040 to
|
||
boot into program mode and appear as a storage device to
|
||
a USB connecte . Saving a .UF2 file to this device will
|
||
replace the Flash ROM contents on the RP2040.
|
||
|
||
A RESET button that allows rebooting the board without disconnecting
|
||
the power.
|
||
|
||
Pin Mapping
|
||
===========
|
||
Pads numbered anticlockwise from USB connector.
|
||
|
||
===== ========== ==========
|
||
Pad Signal Notes
|
||
===== ========== ==========
|
||
1 Reset Pull to ground to reset the RP2040 processor.
|
||
2 3.3V Power out to peripherals.
|
||
3 3.3V Power out to peripherals.
|
||
4 Ground
|
||
5 GPIO26 ADC0
|
||
6 GPIO27 ADC1
|
||
7 GPIO28 ADC2
|
||
8 GPIO29 ADC3
|
||
9 GPIO24
|
||
10 GPIO25
|
||
11 GPIO18
|
||
12 GPIO19
|
||
13 GPIO20
|
||
14 GPIO1 Default RX for UART1 serial console
|
||
15 GPIO0 Default TX for UART0 serial console
|
||
16 GPIO6
|
||
17 GPIO2
|
||
18 GPIO3
|
||
19 GPIO7
|
||
20 GPIO8
|
||
21 GPIO9
|
||
22 GPIO10
|
||
23 GPIO11
|
||
24 GPIO12
|
||
25 GPIO13
|
||
26 VBUS Connected to USB +5V
|
||
27 EN Pull to ground to turn off 3.3V regulator.
|
||
28 VBAT Connected to LiPo battery 3.3V.
|
||
===== ========== ==========
|
||
|
||
The board has a STEMMA QT connector that is also connected to
|
||
pins GPIO2 (I2C1 SDA) and GPIO3 (I2C1 SDA).
|
||
|
||
The board has a two pin JST PH socket that accepts a single 3.3V
|
||
LiPo cell. The cell connected to this port can be charged by
|
||
connecting the board to a USB power supply.
|
||
|
||
There are solder pads on the board that allow the addition of
|
||
a 10-pin serial debug (SWD) connector.
|
||
|
||
Power Supply
|
||
============
|
||
|
||
The Raspberry Pi Pico can be powered via the USB connector,
|
||
or by supplying +5V to pin 39. The board had a diode that prevents
|
||
power from pin 39 from flowing back to the USB socket, although
|
||
the socket can be power via pin 30.
|
||
|
||
The Raspberry Pi Pico chip run on 3.3 volts. This is supplied
|
||
by an onboard voltage regulator. This regulator can be disabled
|
||
by pulling pin 37 to ground.
|
||
|
||
The regulator can run in two modes. By default the regulator runs
|
||
in PFM mode which provides the best efficiency, but may be
|
||
switched to PWM mode for improved ripple by outputting a one
|
||
on GPIO23.
|
||
|
||
|
||
Configurations
|
||
==============
|
||
|
||
audiopack
|
||
---------
|
||
|
||
NuttShell configuration (console enabled in UART0, at 115200 bps) with
|
||
support for NSPlayer audio player.
|
||
|
||
composite
|
||
---------
|
||
|
||
NuttShell configuration (console enabled in UART0, at 115200 bps) with support for
|
||
CDC/ACM with MSC USB composite driver.
|
||
|
||
displaypack
|
||
-----------
|
||
|
||
NuttShell configuration (console enabled in USB Port, at 115200 bps) supporting
|
||
ST7789 video display.
|
||
|
||
enc28j60
|
||
--------
|
||
|
||
NuttShell configuration (console enabled in UART0, at 115200 bps) with support for
|
||
NC28J60.
|
||
|
||
lcd1602
|
||
-------
|
||
|
||
NuttShell configuration (console enabled in UART0, at 115200 bps) with support for
|
||
LCD1602.
|
||
|
||
nsh
|
||
---
|
||
|
||
Basic NuttShell configuration (console enabled in UART0, at 115200 bps).
|
||
|
||
nsh-flash
|
||
---------
|
||
|
||
Basic NuttShell configuration (console enabled in UART0, at 115200 bps
|
||
with SMART flash filesystem.
|
||
|
||
nshsram
|
||
-------
|
||
|
||
NuttShell configuration (console enabled in UART0, at 115200 bps) with interrupt
|
||
vectors in RAM.
|
||
|
||
smp
|
||
---
|
||
|
||
Basic NuttShell configuration (console enabled in UART0, at 115200 bps) with
|
||
both ARM cores enabled.
|
||
|
||
spisd
|
||
-----
|
||
|
||
NuttShell configuration (console enabled in UART0, at 115200 bps) with SPI configured.
|
||
|
||
ssd1306
|
||
-------
|
||
|
||
NuttShell configuration (console enabled in UART0, at 115200 bps) with support for
|
||
ssd1306.
|
||
|
||
st7735
|
||
------
|
||
|
||
NuttShell configuration (console enabled in UART0, at 115200 bps) with support for
|
||
st7735.
|
||
|
||
usbmsc
|
||
------
|
||
|
||
NuttShell configuration (console enabled in UART0, at 115200 bps) with support for
|
||
usbmsc.
|
||
|
||
usbnsh
|
||
------
|
||
|
||
Basic NuttShell configuration (console enabled in USB Port, at 115200 bps).
|
||
|
||
waveshare-lcd-1.14
|
||
------------------
|
||
|
||
NuttShell configuration (console enabled in UART0, at 115200 bps) with support for
|
||
st7789.
|
||
|
||
waveshare-lcd-1.3
|
||
-----------------
|
||
|
||
NuttShell configuration (console enabled in UART0, at 115200 bps) with support for
|
||
usbmsc.
|
||
|