210 lines
7.7 KiB
Plaintext
210 lines
7.7 KiB
Plaintext
README
|
||
^^^^^^
|
||
|
||
README for NuttX port to the Stellaris RDK-S2E Reference Design Kit and
|
||
the MDL-S2E Ethernet to Serial module.
|
||
|
||
Contents
|
||
^^^^^^^^
|
||
|
||
Stellaris RDK-S2E Reference Design Kit
|
||
Stellaris MDL-S2E Reference Design Configuration Options
|
||
Configurations
|
||
|
||
Stellaris RDK-S2E Reference Design Kit
|
||
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
||
|
||
The Stellaris RDK-S2E Reference Design Kit includes the following features:
|
||
|
||
o MDL-S2E Ethernet to serial module
|
||
o LM3S6432 in a 10 x 10 mm BGA package for reduced board size
|
||
o 10/100 Mbit Ethernet port
|
||
o Auto MDI/MDIX cross-over correction
|
||
o Traffic and link indicators Serial ports
|
||
o UART ports include RTS/CTS for flow control
|
||
o UART0 has RS232 levels, transceiver runs at up to 230.4 Kbaud
|
||
o UART1 has CMOS/TTL levels, can run at 1.0 Mbaud
|
||
|
||
Features of the LM3S6432 Microcontroller
|
||
|
||
o 32-bit RISC performance using ARM® Cortex™-M3 v7M architecture
|
||
- 50-MHz operation
|
||
- Hardware-division and single-cycle-multiplication
|
||
- Integrated Nested Vectored Interrupt Controller (NVIC)
|
||
- 42 interrupt channels with eight priority levels
|
||
o 96 KB single-cycle flash
|
||
o 32 KB single-cycle SRAM
|
||
o Three general-purpose 32-bit timers
|
||
o Integrated Ethernet MAC and PHY
|
||
o Two fully programmable 16C550-type UARTs
|
||
o Three 10-bit channels (inputs) when used as single-ended inputs
|
||
o Two independent integrated analog comparators
|
||
o One I2C module
|
||
o One PWM generator block
|
||
– One 16-bit counter
|
||
– Two comparators
|
||
– Produces two independent PWM signals
|
||
– One dead-band generator
|
||
o 0 to 43 GPIOs, depending on user configuration
|
||
o On-chip low drop-out (LDO) voltage regulator
|
||
|
||
GPIO Usage
|
||
|
||
PIN SIGNAL Function
|
||
--- ----------------- ---------------------------------------
|
||
L3 PA0/U0RX UART0 receive
|
||
M3 PA1/U0TX UART0 transmit
|
||
E12 PB0/U0CTS UART0 CTS
|
||
D12 PB1/U0RTS UART0 RTS
|
||
L5 PA4/SPIRX SPI receive (pin hardwired to U1RX)
|
||
M5 PA5/SPITX SPI transmit (pin hardwired to U1TX)
|
||
H2 PD2/U1RX UART1 receive
|
||
H1 PD3/U1TX UART1 transmit
|
||
L4 PA3/U1CTS/SPICLK UART1 CTS or SPI clock
|
||
M4 PA2/U1RTS/SPISEL UART1 RTS or SPI slave select
|
||
J11 PF0/LED1 Ethernet LED1 (green)
|
||
J12 PF1/LED0 Ethernet LED0 (yellow)
|
||
C11 PB2 Transciever #INVALID
|
||
C12 PB3 Transciever #ENABLE
|
||
A6 PB4 Transciever ON
|
||
B7 PB5 Transciever #OFF
|
||
|
||
Stellaris MDL-S2E Reference Design Configuration Options
|
||
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
||
|
||
CONFIG_ARCH - Identifies the arch/ subdirectory. This should
|
||
be set to:
|
||
|
||
CONFIG_ARCH=arm
|
||
|
||
CONFIG_ARCH_family - For use in C code:
|
||
|
||
CONFIG_ARCH_ARM=y
|
||
|
||
CONFIG_ARCH_architecture - For use in C code:
|
||
|
||
CONFIG_ARCH_CORTEXM3=y
|
||
|
||
CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
|
||
|
||
CONFIG_ARCH_CHIP=lm
|
||
|
||
CONFIG_ARCH_CHIP_name - For use in C code to identify the exact
|
||
chip:
|
||
|
||
CONFIG_ARCH_CHIP_LM3S6432
|
||
|
||
CONFIG_ARCH_BOARD - Identifies the configs subdirectory and
|
||
hence, the board that supports the particular chip or SoC.
|
||
|
||
CONFIG_ARCH_BOARD=lm3s6432-s2e (for the Stellaris MDL-S2E Reference Design)
|
||
|
||
CONFIG_ARCH_BOARD_name - For use in C code
|
||
|
||
CONFIG_ARCH_BOARD_LM3S6432S2E
|
||
|
||
CONFIG_ARCH_LOOPSPERMSEC - As supplied, calibrated for correct operation
|
||
of delay loops assuming 50MHz CPU frequency.
|
||
|
||
CONFIG_ENDIAN_BIG - define if big endian (default is little
|
||
endian)
|
||
|
||
CONFIG_RAM_SIZE - Describes the installed DRAM (SRAM in this case):
|
||
|
||
CONFIG_RAM_SIZE=0x00010000 (64Kb)
|
||
|
||
CONFIG_RAM_START - The start address of installed DRAM
|
||
|
||
CONFIG_RAM_START=0x20000000
|
||
|
||
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to boards that
|
||
have LEDs
|
||
|
||
CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
|
||
stack. If defined, this symbol is the size of the interrupt
|
||
stack in bytes. If not defined, the user task stacks will be
|
||
used during interrupt handling.
|
||
|
||
CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
|
||
|
||
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.
|
||
|
||
There are configurations for disabling support for interrupts GPIO ports.
|
||
GPIOH and GPIOJ must be disabled because they do not exist on the LM3S6432.
|
||
Additional interrupt support can be disabled if desired to reduce memory
|
||
footprint - GPIOs C-G are not pinned out on the MDL-S2E board.
|
||
|
||
CONFIG_TIVA_GPIOA_IRQS=y
|
||
CONFIG_TIVA_GPIOB_IRQS=y
|
||
CONFIG_TIVA_GPIOC_IRQS=n << Always
|
||
CONFIG_TIVA_GPIOD_IRQS=n << Always
|
||
CONFIG_TIVA_GPIOE_IRQS=n << Always
|
||
CONFIG_TIVA_GPIOF_IRQS=n << Always
|
||
CONFIG_TIVA_GPIOG_IRQS=n << Always
|
||
CONFIG_TIVA_GPIOH_IRQS=n << Always
|
||
CONFIG_TIVA_GPIOJ_IRQS=n << Always
|
||
|
||
LM3S6432 specific device driver settings
|
||
|
||
CONFIG_UARTn_DISABLE
|
||
The TX and RX pins for UART1 share I/O pins with the TX and RX pins
|
||
for SSI0. To avoid conflicts, only one of SSI0 and UART1 should
|
||
be enabled in a configuration.
|
||
CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the
|
||
console and ttys0 (default is UART1).
|
||
CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received.
|
||
This specific the size of the receive buffer
|
||
CONFIG_UARTn_TXBUFSIZE - Characters are buffered before
|
||
being sent. This specific the size of the transmit buffer
|
||
CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be
|
||
CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8.
|
||
CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
|
||
CONFIG_UARTn_2STOP - Two stop bits
|
||
|
||
CONFIG_TIVA_SSI0 - Select to enable support for SSI0
|
||
The TX and RX pins for SSI0 share I/O pins with the TX and RX pins
|
||
for UART1. To avoid conflicts, only one of SSI0 and UART1 should
|
||
be enabled in a configuration.
|
||
CONFIG_TIVA_SSI1 - Select to enable support for SSI1
|
||
Note that the LM3S6432 only has one SSI, so SSI1 should always be
|
||
disabled.
|
||
CONFIG_SSI_POLLWAIT - Select to disable interrupt driven SSI support.
|
||
Poll-waiting is recommended if the interrupt rate would be to
|
||
high in the interrupt driven case.
|
||
CONFIG_SSI_TXLIMIT - Write this many words to the Tx FIFO before
|
||
emptying the Rx FIFO. If the SPI frequency is high and this
|
||
value is large, then larger values of this setting may cause
|
||
Rx FIFO overrun errors. Default: half of the Tx FIFO size (4).
|
||
|
||
CONFIG_TIVA_ETHERNET - This must be set (along with CONFIG_NET)
|
||
to build the Stellaris Ethernet driver
|
||
CONFIG_TIVA_ETHLEDS - Enable to use Ethernet LEDs on the board.
|
||
CONFIG_TIVA_BOARDMAC - This should be set in order to use the
|
||
MAC address configured in the flash USER registers.
|
||
CONFIG_TIVA_ETHHDUPLEX - Set to force half duplex operation
|
||
CONFIG_TIVA_ETHNOAUTOCRC - Set to suppress auto-CRC generation
|
||
CONFIG_TIVA_ETHNOPAD - Set to suppress Tx padding
|
||
CONFIG_TIVA_MULTICAST - Set to enable multicast frames
|
||
CONFIG_TIVA_PROMISCUOUS - Set to enable promiscuous mode
|
||
CONFIG_TIVA_BADCRC - Set to enable bad CRC rejection.
|
||
CONFIG_TIVA_DUMPPACKET - Dump each packet received/sent to the console.
|
||
|
||
Configurations
|
||
^^^^^^^^^^^^^^
|
||
|
||
Each Stellaris MDL-S2E Reference Design configuration is maintained in a
|
||
sub-directory and can be selected as follow:
|
||
|
||
tools/configure.sh lm3s6432-s2e/<subdir>
|
||
|
||
Where <subdir> is one of the following:
|
||
|
||
nsh:
|
||
Configures the NuttShell (nsh) located at examples/nsh. The
|
||
Configuration enables both the serial and telnetd NSH interfaces.
|
||
|
||
NOTE: As it is configured now, you MUST have a network connected.
|
||
Otherwise, the NSH prompt will not come up because the Ethernet
|
||
driver is waiting for the network to come up. That is probably
|
||
a bug in the Ethernet driver behavior!
|