README
======
This directory contains the port to the NXP LPCXpress-LPC54628 board
(OMI1309UL). This board features:
- LPC54628 Cortex-M4 microcontroller running at up to 220MHz
- 272x480 color LCD with capacitive touch screen
- On-board, high-speed USB, Link2 debug probe with CMSIS-DAP and SEGGER
J-Link protocol options
- UART and SPI port bridging from LPC546xx target to USB via the on-
board debug probe
- Support for external debug probe
- 3 x user LEDs, plus Reset, ISP (3) and user buttons
- Multiple Expansion options, including Arduino UNO and PMod
- Built-in power consumption measurement for target LPC546xx MCU
- 128Mb Micron MT25QL128 Quad-SPI flash
- 16MB Micron MT48LC8M16A2B4 SDRAM
- Knowles SPH0641LM4H digital microphone
- Full size SD/MMC card slot
- NXP MMA8652FCR1 accelerometer
- Stereo audio codec with line in/out
- High and full speed USB ports with micro A/B connector for host or
device functionality
- 10/100Mbps Ethernet (RJ45 connector)
CONTENTS
========
- STATUS
- Configurations
STATUS
======
2017-12-10: The basic NSH configuration is functional at 220MHz with a
Serial console, timer and LED support. Added support for the external
SDRAM and for the RAM test utility.
2017-12-11: Fixed an error in board LEDs. Added framework for future
I2C and SPI flexcomm drivers.
2017-12-12: The SDRAM is now functional and passes the complete RAM
test. Added configuration options and logic to add none, portions, or
all of the external SDRAM to the system heap. Brought in the LPC1788
LCD driver. The LPC1788 LCD registers are identical to the LPC54xx
(other than a minor clock source setting).
2017-12-13: Created the fb configuration for testing the LCD.
2017-12-14: Corrected a misconception about how the video data lines
were configured. The LCD now appears to be fully functional.
2017-12-15: Added an I2C driver.
2017-12-16: Added support for LPC54xx GPIO interrupts; added button
support (with interrupts) to the NSH configuration. The button
test appears to functional functional. There are noticeable delays
in receiving the button events, especially when the button is
released. But if you do not press the buttons too quickly all events
are processed. This, I suspect, is a consequence of the strong glitch
filtering that is enabled in the pin configuration. Snappier
response my be obtainable with filtering off.
2017-12-17: Added a driver for the FT5x06 capacitive, multi-touch
controller. Add support logic for the LPCXpresso-LPC54528 to
initialize and the register the FT5x06 driver. Unfortunately, the
FT5x06 interrupt is on pin P4.0 but pin interrupts are only supported
on P0.m and P1.m, m=0..31.
2017-12-18: Added an option to the FT5x06 driver to support a timer-
based poll instead of interrupts. This is very inefficient in that it
will introduce delays in touchscreen response and will consume more CPU
bandwidth. The driver appears to be functional. Added the NxWM
configuration to do some integrated testing. NxWM seems to be fully
functional. However, the action of the touchscreen could use some
human factors improvements. I imagine that this is a consequence of
the polled solution.
2017-12-19: Brought in Alan Carvalho de Assis' LPC43xx SD/MMC driver from
https://github.com/Smoothieware/smoothie-nuttx/tree/master/nuttx/arch/arm/src/lpc43xx
and adapted it for use by the LPC54xx. Unverified as of this writing.
2017-12-21: Some things are working with he SDMMC drivers but read DMAs
are non-functional and, hence not usable.
2017-12-23: SDMMC is still non-functional. The first DMA read of 512 bytes
fails with a CRC error. Similar result if clock is reduced, if 1-bit bus
is used, if DMA is disabled., if DEBUG output is disabled.
2017-12-24: Added basic DMA support; brought in the WWDT driver from the
LPC43 which has the same peripheral. Neither tested; almost certainly
non-functional without some additional investment.
2017-12-25: Added an RTC driver. It appears to be functional but has not
been well tested.
2017-12-26: Added an RNG driver. The RNG is actually controlled by a ROM
function. This driver seems to work fine when single stepping. However,
if I collect samples indefinitely, I get a reserved interrupt. The symptom
before the crash is that local variables are getting corrupted after the
call into ROM. Increasing the stack size does not seem to help. Perhaps
to use the ROM at high frequencies it may be necessary to modify the ROM
access timing in some way???
2017-12-30: Completed implementation of an Ethernet driver. Untested as
of this writing. Also added the netnsh configuration will, eventually,
be used to test the Ethernet driver.
2018-01-01: There Ethernet driver appears to be fully functional although
more testing is certainly needed.
2018-01-14: The basic SPI driver is code complete but still untested. It
is "basic" in the sense that it supports only polled mode (no DMA).
2018-01-18: Added the lvgl configuration. See notes under "Configuration
Sub-directories" for additional status.
2018-10-22: Dave Marples recently fixed the LPC43 version of the USB
device controller driver. That driver is a clone from the LPC54 USB
DCD. I have backported Dave's changes to the LPC54 DCD. Unfortunately,
it did not fixe the problem. Then I discovered this errata for the LPC54:
For the 4-bit mode to work successfully, four otherwise unused upper
data bits (SD_D[4] to SD_D[7]) must be functionally assigned to GPIO
pins with pull-up resistor. These pins do not need to be physically
connected on the hardware.
With that change (and a lot of other fidgeting), there is some
improvement. I am able to mount and read the SD card .. at least most
of the time. I still get CRC errors when writing and I have not
successfully written to the SD card. It is closer but more TLC is
needed.
2018-10-24: Dave Marples now has the LPC43 SD/MMC working reliably. I
have ported all of Dave's change to the LPC54 but have done no further
testing as of this writing. The feature is still marked EXPERIMENTAL.
There is still no support for the Accelerometer, SPIFI, or USB. There is
a complete but not entirely functional SD card driver and and tested SPI
driver. There are no on-board devices to support SPI testing.
Configurations
==============
Information Common to All Configurations
----------------------------------------
Each LPCXpresso-LPC54628 configuration is maintained in a sub-directory
and can be selected as follow:
.tools/configure.sh [OPTIONS] lpcxpresso-lpc54628/<subdir>
See '.tools/configure.sh -h' for a list of all options. The most typical
are -l to select the Linux host or -c to select the Windows Cygwin host.
Before starting the build, make sure that your PATH environment variable
includes the correct path to your toolchain.
And then build NuttX by simply typing the following. At the conclusion of
the make, the nuttx binary will reside in an ELF file called, simply, nuttx.
make
The <subdir> that is provided above as an argument to the tools/configure.sh
must be is one of the following.
NOTES:
1. These configurations use the mconf-based configuration tool. To
change any of these configurations using that tool, you should:
a. Build and install the kconfig-mconf tool. See nuttx/README.txt
see additional README.txt files in the NuttX tools repository.
b. Execute 'make menuconfig' in nuttx/ in order to start the
reconfiguration process.
2. Unless stated otherwise, all configurations generate console
output on USART0 (aka Flexcomm0). USART0 connects to the serial
bridge on LPC4322JET100 and should be available as a USB serial
device on your host PC.
3. All of these configurations are set up to build under Windows using
the "GNU Tools for ARM Embedded Processors" that is maintained by
ARM (unless stated otherwise in the description of the configuration).
https://developer.arm.com/open-source/gnu-toolchain/gnu-rm
That toolchain selection can easily be reconfigured using
'make menuconfig'. Here are the relevant current settings:
Build Setup:
CONFIG_HOST_WINDOWS=y : Window environment
CONFIG_WINDOWS_CYGWIN=y : Cywin under Windows
System Type -> Toolchain:
CONFIG_ARMV7M_TOOLCHAIN_GNU_EABIW=y : GNU ARM EABI toolchain
Configuration Sub-directories
-----------------------------
fb:
A simple NSH configuration used for some basic debug of LCD using the
framebuffer character drivers. This configuration provides the test
programs:
- apps/examples/pdcurses, and
- apps/examples/fb
as NSH built-in applications.
NOTES:
1. This configuration enables SDRAM to hold the LCD framebuffer and
enables the LPC54xx LCD driver in order to support the LPCXpresso's
TFT panel. In this configuration, the framebuffer resides in the
the lower half megabyte of SDRAM beginning at address 0xa0000000
The remainder of the SDRAM from 0xa0080000 up to 0xa1000000 is added
to the heap.
The is wasteful of SDRAM: Only 261,120 bytes actually used for the
framebuffer. This memory could be reclaimed by changing the DRAM
CS0 offset value in the .config file.
2. Some of the pdcurses test rely on some positional input device and so
is not yet usable. Others work fine with no user include: charset,
xmas, firework, worms, rain, for examples.
3. I2C2 is enabled (will be used with the capacitive touchscreen). In
order to verify I2C functionality, the I2C tool at apps/system/i2ctool
is enabled in this configuration.
nsh> i2c dev -b 2 3 77
0 1 2 3 4 5 6 7 8 9 a b c d e f
00: -- -- -- -- -- -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- 1a -- -- 1d -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: -- -- -- -- -- -- -- -- 38 -- -- -- -- -- -- --
40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --
Codec I2C address: 0x1a
Accel I2C address: 0x1d
Touch panel I2C address: 0x38
4. The touchscreen test program at apps/examples/touchscreen is also
included in this configuration.
nsh> tc 5
tc_main: nsamples: 2
tc_main: Initializing external touchscreen device
tc_main: Opening /dev/input0
Sample :
npoints : 1
Point 1 :
id : 0
flags : 1a
x : 230
y : 84
h : 0
w : 0
pressure : 0
etc.
NOTE that the touchscreen controlled must run in a polled mode! The
FT5x06 interrupt GPIO is on P4.0 and, as far as I know, GPIO
interrupts are not supported on P4. So polled mode only for this
puppy.
lvgl
----
This is a demonstration of the LittlevGL graphics library running on
the NuttX frame buffer driver (as in the fb configuration). You can
find LittlevGL here:
https://littlevgl.com/
https://github.com/littlevgl
This configuration uses the LittlevGL demonstration at apps/examples/lvgldemo.
NOTES:
1. The LittlevGL demonstration is quit large, due mostly to some large
graphic images. So memory is tight in the LPC54628's 512Kb FLASH. In
fact, if you disable optimization, the demo will not fit into FLASH
memory (at least not with debug output also enabled).
A longer term solution might load the large images into the abundant
SDRAM at runtime instead of linking it statically in FLASH.
STATUS:
2018-01-18: The demo is basically function but has some issues:
a) The font is too big on the "Write" screen. They don't fit in on
the keyboard.
b) The "List" display is filled with a big box that says "Click a
button to copy its text to Text area." There are no buttons and
nothing to click on (maybe they are behind the big box?). This
may also be a font size issue.
c) The "Chart" display looks okay.
netnsh:
------
This is a special version of the NuttShell (nsh) configuration that is
tailored for network testing. This version derives from nsh
configuration so many of the notes there apply here except as noted
below.
NOTES:
1. Networking is enabled. The LPCXpressio-LPC54628 has an SMC _LAN8720 PHY
and RJ45 network connector. Support is enabled for IPv4, IPv6, TCP/IP,
UDP, ICMP, ICMPv6, and ARP.
The default IP addresses are 10.0.0.2 (IPv4) and fc00::2 (IPv6). You
should reconfigure these as appropriate for your test network.
2. SD card and I2C support are not enabled. The I2C tool application is
not enabled
3. SDRAM support is enabled and the SDRAM is added to the system heap.
The ramtest application is not enabled.
4. This configuration does not include support for asynchronous network
initialization. As a consequence, NSH must bring up the network
before you get the NSH prompt. If the network cable is unplugged,
this can mean a significant delay before you see the prompt.
5. In this configuration, the network the network and the Telnet
daemon are available by the time that the NSH prompt is presented.
Telnet defaults to IPv6 so to use it from the host PS, you would have
to do:
$ telnet fc00::42
nsh:
Configures the NuttShell (nsh) application located at examples/nsh.
This configuration was used to bring up the board support and, hence,
is focused on low level, command-line driver testing. It has no
network and no graphics capability.
NOTES:
1. NSH built-in applications are supported.
Binary Formats:
CONFIG_BUILTIN=y : Enable support for built-in programs
Application Configuration:
CONFIG_NSH_BUILTIN_APPS=y : Enable starting apps from NSH command line
2. SDRAM support is enabled, but the SDRAM is *not* added to the system
heap. The apps/system/ramtest utility is include in the build as an
NSH builtin function that can be used to verify the SDRAM.
nsh> ramtest -h
RAMTest: Missing required arguments
Usage: <noname> [-w|h|b] <hex-address> <decimal-size>
Where:
<hex-address> starting address of the test.
<decimal-size> number of memory locations (in bytes).
-w Sets the width of a memory location to 32-bits.
-h Sets the width of a memory location to 16-bits (default).
-b Sets the width of a memory location to 8-bits.
The MTL48LC8M16A2B4-6A SDRAM is on CS0 which corresponds to address
0xa0000000, the size of the memory is 128Mbits or 16Mb. So the DRAM
may be tested with this command:
NuttShell (NSH) NuttX-7.23
nsh> ramtest a0000000 16777216
RAMTest: Marching ones: a0000000 16777216
RAMTest: Marching zeroes: a0000000 16777216
RAMTest: Pattern test: a0000000 16777216 55555555 aaaaaaaa
RAMTest: Pattern test: a0000000 16777216 66666666 99999999
RAMTest: Pattern test: a0000000 16777216 33333333 cccccccc
RAMTest: Address-in-address test: a0000000 16777216
nsh>
3. I2C2 is enabled (will be used with the capacitive touchscreen). In
order to verify I2C functionality, the I2C tool at apps/system/i2ctool
is enabled in this configuration.
nsh> i2c bus
BUS EXISTS?
Bus 0: NO
Bus 1: NO
Bus 2: YES
Bus 3: NO
Bus 4: NO
Bus 5: NO
Bus 6: NO
Bus 7: NO
Bus 8: NO
Bus 9: NO
nsh> i2c dev -b 2 3 77
0 1 2 3 4 5 6 7 8 9 a b c d e f
00: -- -- -- -- -- -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- 1a -- -- 1d -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --
I believe that the on-board Accelerometer, Audio Codec, and touch
panel controller should have been detected (but perhaps the touch
panel is not powered in this configuration since the LCD is not
configured?)
Codec I2C address: 0x1a
Accel I2C address: 0x1d
Touch panel I2C address: 0x38
4. Support for the on-board USER button is included as well as the
button test program at apps/examples/buttons. This test is useful
for verifying the functionality of GPIO interrupts.
NuttShell (NSH) NuttX-7.23
nsh> buttons
buttons_main: Starting the button_daemon
buttons_main: button_daemon started
button_daemon: Running
button_daemon: Opening /dev/buttons
button_daemon: Supported BUTTONs 0x01
nsh> Sample = 1
Sample = 0
Sample = 1
Sample = 0
Sample = 1
Sample = 0
Sample = 1
etc.
There are noticeable delays in receiving the button events,
especially when the button is released. But if you do not press the
buttons too quickly all events are processed. This, I suspect, is a
consequence of the strong glitch filtering that is enabled in the pin
configuration. Snappier response my be obtainable with filtering off
if desired.
5. This configuration has been used for testing the SDMMC driver with
these configuration additions:
CONFIG_EXPERIMENTAL=y
CONFIG_LPC54_SDMMC=y
CONFIG_LPC54_SDMMC_PWRCTRL=y
CONFIG_LPC54_SDMMC_DMA=y
CONFIG_SIG_SIGWORK=17
CONFIG_SCHED_WORKQUEUE=y
CONFIG_SCHED_HPWORK=y
CONFIG_SCHED_HPWORKPRIORITY=224
CONFIG_SCHED_HPWORKSTACKSIZE=2048
CONFIG_MMCSD=y
CONFIG_MMCSD_NSLOTS=1
CONFIG_MMCSD_MULTIBLOCK_DISABLE=y
CONFIG_MMCSD_HAVE_CARDDETECT=y
CONFIG_MMCSD_HAVE_WRITEPROTECT=y
CONFIG_ARCH_HAVE_SDIO=y
CONFIG_SDIO_DMA=y
CONFIG_MMCSD_SDIO=y
CONFIG_NSH_MMCSDSLOTNO=0
6. The RTC is enabled in this configuration.
NuttShell (NSH) NuttX-7.23
nsh> date
Jan 01 00:00:06 1970
nsh> date -s "DEC 25 08:00:00 2017"
nsh> date
Dec 25 08:00:01 2017
After reset:
NuttShell (NSH) NuttX-7.23
nsh> date
Dec 25 08:00:05 2017
nxwm:
This is a special configuration setup for the NxWM window manager
UnitTest. This builds on top of the features that were unit tested in
by the fb configuration.
The NxWM window manager can be found here:
apps/graphics/NxWidgets/nxwm
The NxWM unit test can be found at:
apps/graphics/NxWidgets/UnitTests/nxwm
pwfb:
This configuration uses the test at apps/examples/pwfb to verify the
operation of the per-window framebuffers. That example shows three
windows containing text moving around, crossing each other from
"above" and from "below". The example application is NOT updating the
windows any anyway! The application is only changing the window
position. The windows are being updated from the per-winidow
framebuffers automatically.
This example is reminescent of Pong: Each window travels in straight
line until it hits an edge, then it bounces off. The window is also
raised when it hits the edge (gets "focus"). This tests all
combinations of overap.
2019-03-19: Everything works fine!
pwlines:
This configuration uses the test at apps/examples/pwline. It is another
verification of the operation of the per-window framebuffers. This
examples is very similar to the pwfb example used in pwfb configuration
except that instead of text, each window has an (trivial) animated
graphic (based on the rotating line of apps/examples/nslines).
2019-03-20: Everything works fine!
twm4nx:
This configuration exercises the port of TWM to NuttX. A description of
that port is available at apps/graphics/twm4nx/README.txt.
NOTES:
1. This version uses the on-board display with the touchscreen for
positional input (instead of a mouse). Keyboard input is currently
disabled only because (1) there is no Twm4Nx application that needs
it, and (2) I will first need to create a USB host driver to support
a USB keyboard.
STATUS:
2019-05-04: Initial display is clean but touchscren input is not yet
functional. Left-click main menu functionality is required to test
much more.
