85 lines
3.0 KiB
C
85 lines
3.0 KiB
C
/****************************************************************************
|
|
* boards/arm/nrf52/arduino-nano-33ble-rev2/src/nrf52_boot.c
|
|
*
|
|
* Licensed to the Apache Software Foundation (ASF) under one or more
|
|
* contributor license agreements. See the NOTICE file distributed with
|
|
* this work for additional information regarding copyright ownership. The
|
|
* ASF licenses this file to you under the Apache License, Version 2.0 (the
|
|
* "License"); you may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at
|
|
*
|
|
* http://www.apache.org/licenses/LICENSE-2.0
|
|
*
|
|
* Unless required by applicable law or agreed to in writing, software
|
|
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
|
|
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
|
|
* License for the specific language governing permissions and limitations
|
|
* under the License.
|
|
*
|
|
****************************************************************************/
|
|
|
|
/****************************************************************************
|
|
* Included Files
|
|
****************************************************************************/
|
|
|
|
#include <nuttx/config.h>
|
|
|
|
#include <debug.h>
|
|
|
|
#include <nuttx/board.h>
|
|
#include <arch/board/board.h>
|
|
|
|
#include "arm_internal.h"
|
|
#include "arduino-nano-33ble.h"
|
|
|
|
/****************************************************************************
|
|
* Public Functions
|
|
****************************************************************************/
|
|
|
|
/****************************************************************************
|
|
* Name: nrf52_board_initialize
|
|
*
|
|
* Description:
|
|
* All NRF52xxx architectures must provide the following entry point.
|
|
* This entry point is called early in the initialization -- after all
|
|
* memory has been configured and mapped but before any devices have been
|
|
* initialized.
|
|
*
|
|
****************************************************************************/
|
|
|
|
void nrf52_board_initialize(void)
|
|
{
|
|
/* Configure on-board LEDs if LED support has been selected. */
|
|
|
|
#ifdef CONFIG_ARCH_LEDS
|
|
board_autoled_initialize();
|
|
#endif
|
|
|
|
/* If I2C 0 is enabled and we are master, engage pullup resistor. */
|
|
#ifdef CONFIG_NRF52_I2C0_MASTER
|
|
nrf52_gpio_config(BOARD_I2C0_PULLUP_PIN);
|
|
#endif
|
|
}
|
|
|
|
/****************************************************************************
|
|
* Name: board_late_initialize
|
|
*
|
|
* Description:
|
|
* If CONFIG_BOARD_LATE_INITIALIZE is selected, then an additional
|
|
* initialization call will be performed in the boot-up sequence to a
|
|
* function called board_late_initialize(). board_late_initialize() will be
|
|
* called immediately after up_initialize() is called and just before the
|
|
* initial application is started. This additional initialization phase
|
|
* may be used, for example, to initialize board-specific device drivers.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#ifdef CONFIG_BOARD_LATE_INITIALIZE
|
|
void board_late_initialize(void)
|
|
{
|
|
/* Perform board-specific initialization */
|
|
|
|
nrf52_bringup();
|
|
}
|
|
#endif
|