README
======
This directory contains the port of NuttX to the Adafruit Metro M4. The
Metro M4 uses a Arduino form factor and and pinout. It's powered with an
ATSAMD51J19:
o Cortex M4 core running at 120 MHz
o Hardware DSP and floating point support
o 512 KB flash, 192 KB RAM
o 32-bit, 3.3V logic and power
o Dual 1 MSPS DAC (A0 and A1)
o Dual 1 MSPS ADC (8 analog pins)
o 6 x hardware SERCOM (I2C, SPI or UART)
o 16 x PWM outputs
o Stereo I2S input/output with MCK pin
o 10-bit Parallel capture controller (for camera/video in)
o Built in crypto engines with AES (256 bit), true RNG, Pubkey controller
o 64 QFN
STATUS
======
2018-07-26: The basic port was merged into master. It is still
incomplete and untested. It is missing the clock configuration logic.
There is a placeholder from the SAML21, but it is currently stubbed out
in the Make.defs file. Configuration options in the board.h header
file are bogus and also just cloned from the SAML21.
2018-07-29: Clock configuration logic now complete. board.h
configuration options still need to be verified. Unverified SERCOM
USART, SPI, I2C, Port configuration, and DMA support have been added.
I still have no hardware in hand to test.
2018-07-20: Brought in the USB driver from the SAML21. It is the same
USB IP with only small differences. There a a few, small open issues
still to be resolved.
2018-08-01: Hardware in hand. Initial attempts to program the board
using a Segger J-Link connected via SWD were unsuccessful. I believe
that the FLASH is locked. See "Unlocking FLASH with J-Link Commander"
below. Unfortunately, this seems to have rendered by board unusable.
Sigh.
Unlocking FLASH
===============
Options
-------
The Adafruit Metro M4 comes with a very nice bootloader resident in FLASH.
so we have two options:
1. Learn to play well with others. Make NuttX coexist and work in the
memory partition available to it. Or,
2. Be greedy, unlock the FLASH and overwrite the bootloader.
I chose to do the last one. I used a Segger J-Link and here are the steps
that I took. You can probably do these things in Atmel Studio (?) but for
other debug environments, you would have to come up with the solution.
Unlocking FLASH with J-Link Commander
-------------------------------------
1. Start J-Link Commander:
SEGGER J-Link Commander V6.32i (Compiled Jul 24 2018 15:20:49)
DLL version V6.32i, compiled Jul 24 2018 15:19:55
Connecting to J-Link via USB...O.K.
Firmware: J-Link V9 compiled Apr 20 2018 16:47:26
Hardware version: V9.30
S/N: 269303123
License(s): FlashBP, GDB
OEM: SEGGER-EDU
VTref=3.296V
Type "connect" to establish a target connection, '?' for help
J-Link>con
Please specify device / core. <Default>: ATSAMD51P19
Type '?' for selection dialog
Device>ATSAMD51P19
Please specify target interface:
J) JTAG (Default)
S) SWD
TIF>S
Specify target interface speed [kHz]. <Default>: 4000 kHz
Speed>
Device "ATSAMD51P19" selected.
Connecting to target via SWD
Found SW-DP with ID 0x2BA01477
Scanning AP map to find all available APs
...etc. ...
2. Look at The NVM "user page" memory at address 0x00804000:
J-Link>mem8 804000, 10
00804000 = 39 92 9A F6 80 FF EC AE FF FF FF FF FF FF FF FF
The field NVM BOOT (also called BOOTPROT) is the field that locks the
lower part of FLASH to support the boot loader. This is bits 26-29
of the NVM user page:
J-Link>mem32 804000, 1
00804000 = F69A9239
In binary 11|11 01|10 1001 1010 1001 0010 0011 1001, so NVM Boot 1101.
To unlock the FLASH memory reserved for the bootloader, we need to
change this field to 111 so that:
1111 01|11 11|01 1010 1001 0010 0011 1001 = F7da9239, or
00804000 = 39 92 DA F7 80 FF EC AE FF FF FF FF FF FF FF FF
is read.
3. Modify the NVM "user page"
I did this using the instructions for the SAMD21 found at
https://roamingthings.de/use-j-link-to-change-the-boot-loader-protection-of-a-sam-d21/
We will need to create a small Motorola S-REC file to write new values
into NVM. See https://en.m.wikipedia.org/wiki/SREC_(file_format) for a
description of the Motorola SREC format.
I wrote a small program at configs/metro-m4-scripts/nvm.c that will
generate this Motorola SREC file with the correct checksum. The file at
configs/metro-m4-scripts/nvm.c is the output of that program.
J-Link>mem8 804000,10
00804000 = 39 92 9A F6 80 FF EC AE FF FF FF FF FF FF FF FF
J-Link>loadfile D:\Spuda\Documents\projects\nuttx\master\nuttx\configs\metro-m4\scripts\nvm.srec
Downloading file [D:\Spuda\Documents\projects\nuttx\master\nuttx\configs\metro-m4\scripts\nvm.srec]...
J-Link: Flash download: Bank 1 @ 0x00804000: 1 range affected (16 bytes)
J-Link: Flash download: Total time needed: 0.089s (Prepare: 0.035s, Compare: 0.011s, Erase: 0.000s, Program: 0.019s, Verify: 0.011s, Restore: 0.011s)
O.K.
J-Link>mem8 804000,10
00804000 = 39 92 9A FE 80 FF EC AE FF FF FF FF FF FF FF FF
You will, of course, have to change the path as appropriate for your system.
Serial Console
==============
An Arduino compatible serial Shield is assumed (or equivalently, and
external RS-232 or serial-to-USB adapter connected on Arduino pins D0 and
D1):
------ ----------------- -----------
SHIELD SAMD5E5 FUNCTION
------ ----------------- -----------
D0 PA23 SERCOM3 PAD2 RXD
D1 PA22 SERCOM3 PAD0 TXD
LEDs
====
The Adafruit Metro M4 has four LEDs, but only two are controllable by software:
1. The red LED on the Arduino D13 pin, and
2. A NeoPixel RGB LED.
Currently, only the red LED is supported.
------ ----------------- -----------
SHIELD SAMD5E5 FUNCTION
------ ----------------- -----------
D13 PA16 GPIO output
Configurations
==============
Each Adafruit Metro M4 configuration is maintained in a sub-directory and
can be selected as follow:
tools/configure.sh [OPTIONS] metro-m4/<subdir>
Do 'tools/configure.sh -h' for the list of options. If you are building
under Windows with Cygwin, you would need the -c option, for example.
Before building, make sure that the PATH environmental variable includes the
correct path to the directory than holds your toolchain binaries.
And then build NuttX by simply typing the following. At the conclusion of
the make, the nuttx binary will reside in an ELF file called, simply, nuttx.
make
The <subdir> that is provided above as an argument to the tools/configure.sh
must be is one of configurations listed in the following paragraph.
NOTES:
1. These configurations use the mconf-based configuration tool. To
change any of these configurations using that tool, you should:
a. Build and install the kconfig-mconf tool. See nuttx/README.txt
see additional README.txt files in the NuttX tools repository.
b. Execute 'make menuconfig' in nuttx/ in order to start the
reconfiguration process.
2. Unless stated otherwise, all configurations generate console
output of on SERCOM3 which is available on a Arduino Serial
Shield (see the section "Serial Console" above).
3. Unless otherwise stated, the configurations are setup build under
Linux with a generic ARM EABI toolchain:
Configuration sub-directories
-----------------------------
nsh:
This configuration directory will built the NuttShell. See NOTES above.
