409 lines
14 KiB
C
409 lines
14 KiB
C
/****************************************************************************
|
||
* boards/arm/stm32/stm32f401rc-rs485/include/board.h
|
||
*
|
||
* Licensed to the Apache Software Foundation (ASF) under one or more
|
||
* contributor license agreements. See the NOTICE file distributed with
|
||
* this work for additional information regarding copyright ownership. The
|
||
* ASF licenses this file to you under the Apache License, Version 2.0 (the
|
||
* "License"); you may not use this file except in compliance with the
|
||
* License. You may obtain a copy of the License at
|
||
*
|
||
* http://www.apache.org/licenses/LICENSE-2.0
|
||
*
|
||
* Unless required by applicable law or agreed to in writing, software
|
||
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
|
||
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
|
||
* License for the specific language governing permissions and limitations
|
||
* under the License.
|
||
*
|
||
****************************************************************************/
|
||
|
||
#ifndef __BOARDS_ARM_STM32F401RC_RS485_INCLUDE_BOARD_H
|
||
#define __BOARDS_ARM_STM32F401RC_RS485_INCLUDE_BOARD_H
|
||
|
||
/****************************************************************************
|
||
* Included Files
|
||
****************************************************************************/
|
||
|
||
#include <nuttx/config.h>
|
||
#ifndef __ASSEMBLY__
|
||
# include <stdint.h>
|
||
#endif
|
||
|
||
/****************************************************************************
|
||
* Pre-processor Definitions
|
||
****************************************************************************/
|
||
|
||
/* Clocking *****************************************************************/
|
||
|
||
/* The STM32F401RC-RS485 uses an external 32kHz cristal (X2) to enable HSE
|
||
* clock.
|
||
*
|
||
* System Clock source : PLL (HSI)
|
||
* SYSCLK(Hz) : 84000000 Determined by PLL
|
||
* configuration
|
||
* HCLK(Hz) : 84000000 (STM32_RCC_CFGR_HPRE)
|
||
* AHB Prescaler : 1 (STM32_RCC_CFGR_HPRE)
|
||
* APB1 Prescaler : 2 (STM32_RCC_CFGR_PPRE1)
|
||
* APB2 Prescaler : 1 (STM32_RCC_CFGR_PPRE2)
|
||
* HSI Frequency(Hz) : 16000000 (nominal)
|
||
* PLLM : 16 (STM32_PLLCFG_PLLM)
|
||
* PLLN : 336 (STM32_PLLCFG_PLLN)
|
||
* PLLP : 4 (STM32_PLLCFG_PLLP)
|
||
* PLLQ : 7 (STM32_PLLCFG_PPQ)
|
||
* Flash Latency(WS) : 5
|
||
* Prefetch Buffer : OFF
|
||
* Instruction cache : ON
|
||
* Data cache : ON
|
||
* Require 48MHz for USB OTG FS, : Enabled
|
||
* SDIO and RNG clock
|
||
*/
|
||
|
||
/* HSI - 16 MHz RC factory-trimmed
|
||
* LSI - 32 KHz RC
|
||
* HSE - not installed
|
||
* LSE - not installed
|
||
*/
|
||
|
||
#define STM32_HSI_FREQUENCY 16000000ul
|
||
#define STM32_LSI_FREQUENCY 32000
|
||
#define STM32_BOARD_USEHSI 1
|
||
|
||
/* Main PLL Configuration.
|
||
*
|
||
* Formulae:
|
||
*
|
||
* VCO input frequency = PLL input clock frequency / PLLM,
|
||
* 2 <= PLLM <= 63
|
||
* VCO output frequency = VCO input frequency × PLLN,
|
||
* 192 <= PLLN <= 432
|
||
* PLL output clock frequency = VCO frequency / PLLP,
|
||
* PLLP = 2, 4, 6, or 8
|
||
* USB OTG FS clock frequency = VCO frequency / PLLQ,
|
||
* 2 <= PLLQ <= 15
|
||
*
|
||
* We would like to have SYSYCLK=84MHz and we must have the USB clock= 48MHz.
|
||
* Some possible solutions include:
|
||
*
|
||
* PLLN=210 PLLM=5 PLLP=8 PLLQ=14 SYSCLK=84000000 OTGFS=48000000
|
||
* PLLN=210 PLLM=10 PLLP=4 PLLQ=7 SYSCLK=84000000 OTGFS=48000000
|
||
* PLLN=336 PLLM=8 PLLP=8 PLLQ=14 SYSCLK=84000000 OTGFS=48000000
|
||
* PLLN=336 PLLM=16 PLLP=4 PLLQ=7 SYSCLK=84000000 OTGFS=48000000
|
||
* PLLN=420 PLLM=10 PLLP=8 PLLQ=14 SYSCLK=84000000 OTGFS=48000000
|
||
* PLLN=420 PLLM=20 PLLP=4 PLLQ=7 SYSCLK=84000000 OTGFS=48000000
|
||
*
|
||
* We will configure like this
|
||
*
|
||
* PLL source is HSI
|
||
* PLL_VCO = (STM32_HSI_FREQUENCY / PLLM) * PLLN
|
||
* = (16,000,000 / 16) * 336
|
||
* = 336,000,000
|
||
* SYSCLK = PLL_VCO / PLLP
|
||
* = 336,000,000 / 4 = 84,000,000
|
||
* USB OTG FS and SDIO Clock
|
||
* = PLL_VCO / PLLQ
|
||
* = 336,000,000 / 7 = 48,000,000
|
||
*
|
||
* REVISIT: Trimming of the HSI is not yet supported.
|
||
*/
|
||
|
||
#define STM32_PLLCFG_PLLM RCC_PLLCFG_PLLM(16)
|
||
#define STM32_PLLCFG_PLLN RCC_PLLCFG_PLLN(336)
|
||
#define STM32_PLLCFG_PLLP RCC_PLLCFG_PLLP_4
|
||
#define STM32_PLLCFG_PLLQ RCC_PLLCFG_PLLQ(7)
|
||
|
||
#define STM32_SYSCLK_FREQUENCY 84000000ul
|
||
|
||
/* AHB clock (HCLK) is SYSCLK (84MHz) */
|
||
|
||
#define STM32_RCC_CFGR_HPRE RCC_CFGR_HPRE_SYSCLK /* HCLK = SYSCLK / 1 */
|
||
#define STM32_HCLK_FREQUENCY STM32_SYSCLK_FREQUENCY
|
||
|
||
/* APB1 clock (PCLK1) is HCLK/2 (42MHz) */
|
||
|
||
#define STM32_RCC_CFGR_PPRE1 RCC_CFGR_PPRE1_HCLKd2 /* PCLK1 = HCLK / 2 */
|
||
#define STM32_PCLK1_FREQUENCY (STM32_HCLK_FREQUENCY/2)
|
||
|
||
/* Timers driven from APB1 will be twice PCLK1 */
|
||
|
||
/* REVISIT */
|
||
|
||
#define STM32_APB1_TIM2_CLKIN (2*STM32_PCLK1_FREQUENCY)
|
||
#define STM32_APB1_TIM3_CLKIN (2*STM32_PCLK1_FREQUENCY)
|
||
#define STM32_APB1_TIM4_CLKIN (2*STM32_PCLK1_FREQUENCY)
|
||
#define STM32_APB1_TIM5_CLKIN (2*STM32_PCLK1_FREQUENCY)
|
||
#define STM32_APB1_TIM6_CLKIN (2*STM32_PCLK1_FREQUENCY)
|
||
#define STM32_APB1_TIM7_CLKIN (2*STM32_PCLK1_FREQUENCY)
|
||
#define STM32_APB1_TIM12_CLKIN (2*STM32_PCLK1_FREQUENCY)
|
||
#define STM32_APB1_TIM13_CLKIN (2*STM32_PCLK1_FREQUENCY)
|
||
#define STM32_APB1_TIM14_CLKIN (2*STM32_PCLK1_FREQUENCY)
|
||
|
||
/* APB2 clock (PCLK2) is HCLK (84MHz) */
|
||
|
||
#define STM32_RCC_CFGR_PPRE2 RCC_CFGR_PPRE2_HCLK /* PCLK2 = HCLK / 1 */
|
||
#define STM32_PCLK2_FREQUENCY (STM32_HCLK_FREQUENCY/1)
|
||
|
||
/* Timers driven from APB2 will be twice PCLK2 */
|
||
|
||
/* REVISIT */
|
||
|
||
#define STM32_APB2_TIM1_CLKIN (2*STM32_PCLK2_FREQUENCY)
|
||
#define STM32_APB2_TIM8_CLKIN (2*STM32_PCLK2_FREQUENCY)
|
||
#define STM32_APB2_TIM9_CLKIN (2*STM32_PCLK1_FREQUENCY)
|
||
#define STM32_APB2_TIM10_CLKIN (2*STM32_PCLK1_FREQUENCY)
|
||
#define STM32_APB2_TIM11_CLKIN (2*STM32_PCLK1_FREQUENCY)
|
||
|
||
/* Timer Frequencies, if APBx is set to 1, frequency is same to APBx
|
||
* otherwise frequency is 2xAPBx.
|
||
* Note: TIM1,8 are on APB2, others on APB1
|
||
*/
|
||
|
||
/* REVISIT */
|
||
|
||
#define BOARD_TIM1_FREQUENCY (2*STM32_PCLK2_FREQUENCY)
|
||
#define BOARD_TIM2_FREQUENCY (2*STM32_PCLK1_FREQUENCY)
|
||
#define BOARD_TIM3_FREQUENCY (2*STM32_PCLK1_FREQUENCY)
|
||
#define BOARD_TIM4_FREQUENCY (2*STM32_PCLK1_FREQUENCY)
|
||
#define BOARD_TIM5_FREQUENCY (2*STM32_PCLK1_FREQUENCY)
|
||
#define BOARD_TIM6_FREQUENCY (2*STM32_PCLK1_FREQUENCY)
|
||
#define BOARD_TIM7_FREQUENCY (2*STM32_PCLK1_FREQUENCY)
|
||
#define BOARD_TIM8_FREQUENCY (2*STM32_PCLK2_FREQUENCY)
|
||
|
||
/* SDIO dividers. Note that slower clocking is required when DMA is disabled
|
||
* in order to avoid RX overrun/TX underrun errors due to delayed responses
|
||
* to service FIFOs in interrupt driven mode. These values have not been
|
||
* tuned!!!
|
||
*
|
||
* HCLK=72MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(178+2)=400 KHz
|
||
*/
|
||
|
||
/* REVISIT */
|
||
|
||
#define SDIO_INIT_CLKDIV (178 << SDIO_CLKCR_CLKDIV_SHIFT)
|
||
|
||
/* DMA ON: HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(2+2)=18 MHz
|
||
* DMA OFF: HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(3+2)=14.4 MHz
|
||
*/
|
||
|
||
/* REVISIT */
|
||
|
||
#ifdef CONFIG_SDIO_DMA
|
||
# define SDIO_MMCXFR_CLKDIV (2 << SDIO_CLKCR_CLKDIV_SHIFT)
|
||
#else
|
||
# define SDIO_MMCXFR_CLKDIV (3 << SDIO_CLKCR_CLKDIV_SHIFT)
|
||
#endif
|
||
|
||
/* DMA ON: HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(1+2)=24 MHz
|
||
* DMA OFF: HCLK=72 MHz, SDIOCLK=72MHz, SDIO_CK=HCLK/(3+2)=14.4 MHz
|
||
*/
|
||
|
||
/* REVISIT */
|
||
|
||
#ifdef CONFIG_SDIO_DMA
|
||
# define SDIO_SDXFR_CLKDIV (1 << SDIO_CLKCR_CLKDIV_SHIFT)
|
||
#else
|
||
# define SDIO_SDXFR_CLKDIV (3 << SDIO_CLKCR_CLKDIV_SHIFT)
|
||
#endif
|
||
|
||
/****************************************************************************
|
||
* Public Data
|
||
****************************************************************************/
|
||
|
||
#ifndef __ASSEMBLY__
|
||
|
||
#undef EXTERN
|
||
#if defined(__cplusplus)
|
||
#define EXTERN extern "C"
|
||
extern "C"
|
||
{
|
||
#else
|
||
#define EXTERN extern
|
||
#endif
|
||
|
||
/****************************************************************************
|
||
* Public Function Prototypes
|
||
****************************************************************************/
|
||
|
||
#undef EXTERN
|
||
#if defined(__cplusplus)
|
||
}
|
||
#endif
|
||
|
||
#endif /* __ASSEMBLY__ */
|
||
|
||
/****************************************************************************
|
||
* Pre-processor Definitions
|
||
****************************************************************************/
|
||
|
||
/* DMA Channel/Stream Selections ********************************************/
|
||
|
||
/* Stream selections are arbitrary for now but might become important in
|
||
* the future is we set aside more DMA channels/streams.
|
||
*
|
||
* SDIO DMA
|
||
* DMAMAP_SDIO_1 = Channel 4, Stream 3 <- may later be used by SPI DMA
|
||
* DMAMAP_SDIO_2 = Channel 4, Stream 6
|
||
*/
|
||
|
||
#define DMAMAP_SDIO DMAMAP_SDIO_1
|
||
|
||
/* Need to VERIFY fwb */
|
||
|
||
#define DMACHAN_SPI1_RX DMAMAP_SPI1_RX_1
|
||
#define DMACHAN_SPI1_TX DMAMAP_SPI1_TX_1
|
||
#define DMACHAN_SPI2_RX DMAMAP_SPI2_RX
|
||
#define DMACHAN_SPI2_TX DMAMAP_SPI2_TX
|
||
|
||
/* Alternate function pin selections ****************************************/
|
||
|
||
/* USART1:
|
||
* RXD: PA10 CN9 pin 3, CN10 pin 33
|
||
* PB7 CN7 pin 21
|
||
* TXD: PA9 CN5 pin 1, CN10 pin 21
|
||
* PB6 CN5 pin 3, CN10 pin 17
|
||
*/
|
||
|
||
#if 1
|
||
# define GPIO_USART1_RX GPIO_USART1_RX_1 /* PA10 */
|
||
# define GPIO_USART1_TX GPIO_USART1_TX_1 /* PA9 */
|
||
#else
|
||
# define GPIO_USART1_RX GPIO_USART1_RX_2 /* PB7 */
|
||
# define GPIO_USART1_TX GPIO_USART1_TX_2 /* PB6 */
|
||
#endif
|
||
|
||
/* USART2:
|
||
* RXD: PA3 CN9 pin 1 (See SB13, 14, 62, 63). CN10 pin 37
|
||
* PD6
|
||
* TXD: PA2 CN9 pin 2(See SB13, 14, 62, 63). CN10 pin 35
|
||
* PD5
|
||
*/
|
||
|
||
#define GPIO_USART2_RX GPIO_USART2_RX_1 /* PA3 */
|
||
#define GPIO_USART2_TX GPIO_USART2_TX_1 /* PA2 */
|
||
#define GPIO_USART2_RTS GPIO_USART2_RTS_2
|
||
#define GPIO_USART2_CTS GPIO_USART2_CTS_2
|
||
|
||
/* USART6:
|
||
* RXD: PC7 CN5 pin2, CN10 pin 19
|
||
* PA12 CN10, pin 12
|
||
* TXD: PC6 CN10, pin 4
|
||
* PA11 CN10, pin 14
|
||
*/
|
||
|
||
#define GPIO_USART6_RX GPIO_USART6_RX_1 /* PC7 */
|
||
#define GPIO_USART6_TX GPIO_USART6_TX_1 /* PC6 */
|
||
|
||
/* UART RX DMA configurations */
|
||
|
||
#define DMAMAP_USART1_RX DMAMAP_USART1_RX_2
|
||
#define DMAMAP_USART6_RX DMAMAP_USART6_RX_2
|
||
|
||
/* I2C
|
||
*
|
||
* The optional _GPIO configurations allow the I2C driver to manually
|
||
* reset the bus to clear stuck slaves. They match the pin configuration,
|
||
* but are normally-high GPIOs.
|
||
*/
|
||
|
||
#define GPIO_I2C1_SCL GPIO_I2C1_SCL_2
|
||
#define GPIO_I2C1_SDA GPIO_I2C1_SDA_2
|
||
#define GPIO_I2C1_SCL_GPIO \
|
||
(GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN8)
|
||
#define GPIO_I2C1_SDA_GPIO \
|
||
(GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN9)
|
||
|
||
#define GPIO_I2C2_SCL GPIO_I2C2_SCL_1
|
||
#define GPIO_I2C2_SDA GPIO_I2C2_SDA_1
|
||
#define GPIO_I2C2_SCL_GPIO \
|
||
(GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN10)
|
||
#define GPIO_I2C2_SDA_GPIO \
|
||
(GPIO_OUTPUT|GPIO_OPENDRAIN|GPIO_SPEED_50MHz|GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN11)
|
||
|
||
/* SPI
|
||
*
|
||
* There are sensors on SPI1, and SPI2 is connected to the FRAM.
|
||
*/
|
||
|
||
#define GPIO_SPI1_MISO GPIO_SPI1_MISO_1
|
||
#define GPIO_SPI1_MOSI GPIO_SPI1_MOSI_1
|
||
#define GPIO_SPI1_SCK GPIO_SPI1_SCK_1
|
||
|
||
#define GPIO_SPI2_MISO GPIO_SPI2_MISO_1
|
||
#define GPIO_SPI2_MOSI GPIO_SPI2_MOSI_1
|
||
#define GPIO_SPI2_SCK GPIO_SPI2_SCK_2
|
||
|
||
/* LEDs
|
||
*
|
||
* The STM32F401RC-RS485 boards provide 4 blue user LEDs. LD1, LD2, LD3
|
||
* and LD4 that are connected to MCU I/O pins PC0, PC1, PC2 and PC3.
|
||
* - When the I/O is HIGH value, the LED is on.
|
||
* - When the I/O is LOW, the LED is off.
|
||
*/
|
||
|
||
/* LED index values for use with board_userled() */
|
||
|
||
#define BOARD_LD1 0
|
||
#define BOARD_LD2 1
|
||
#define BOARD_LD3 2
|
||
#define BOARD_LD4 3
|
||
#define BOARD_NLEDS 4
|
||
|
||
/* LED bits for use with board_userled_all() */
|
||
|
||
#define BOARD_LED1_BIT (1 << BOARD_LD1)
|
||
#define BOARD_LED2_BIT (1 << BOARD_LD2)
|
||
#define BOARD_LED3_BIT (1 << BOARD_LD3)
|
||
#define BOARD_LED4_BIT (1 << BOARD_LD4)
|
||
|
||
/* These LEDs are not used by the board port unless CONFIG_ARCH_LEDS is
|
||
* defined. In that case, the usage by the board port is defined in
|
||
* include/board.h and src/sam_leds.c. The LEDs are used to encode OS-related
|
||
* events as follows when the red LED (PE24) is available:
|
||
*
|
||
* SYMBOL Meaning LD2
|
||
* ------------------- ----------------------- -----------
|
||
* LED_STARTED NuttX has been started OFF
|
||
* LED_HEAPALLOCATE Heap has been allocated OFF
|
||
* LED_IRQSENABLED Interrupts enabled OFF
|
||
* LED_STACKCREATED Idle stack created ON
|
||
* LED_INIRQ In an interrupt No change
|
||
* LED_SIGNAL In a signal handler No change
|
||
* LED_ASSERTION An assertion failed No change
|
||
* LED_PANIC The system has crashed Blinking
|
||
* LED_IDLE MCU is is sleep mode Not used
|
||
*
|
||
* Thus if LD2, NuttX has successfully booted and is, apparently, running
|
||
* normally. If LD2 is flashing at approximately 2Hz, then a fatal error
|
||
* has been detected and the system has halted.
|
||
*/
|
||
|
||
#define LED_STARTED 0
|
||
#define LED_HEAPALLOCATE 0
|
||
#define LED_IRQSENABLED 0
|
||
#define LED_STACKCREATED 1
|
||
#define LED_INIRQ 2
|
||
#define LED_SIGNAL 2
|
||
#define LED_ASSERTION 2
|
||
#define LED_PANIC 1
|
||
|
||
/* Buttons
|
||
* The STM32F401RC-RS485 has 4 user buttons: SW3, SW4, SW5 and
|
||
* SW6. They are connected to PB13, PB14, PB15 and PC6 respectively.
|
||
*/
|
||
|
||
#define BUTTON_SW3 0
|
||
#define BUTTON_SW4 1
|
||
#define BUTTON_SW5 2
|
||
#define BUTTON_SW6 3
|
||
#define NUM_BUTTONS 4
|
||
|
||
#define BUTTON_SW3_BIT (1 << BUTTON_SW3)
|
||
#define BUTTON_SW4_BIT (1 << BUTTON_SW4)
|
||
#define BUTTON_SW5_BIT (1 << BUTTON_SW5)
|
||
#define BUTTON_SW6_BIT (1 << BUTTON_SW6)
|
||
|
||
#define GPIO_TIM2_CH1IN (GPIO_TIM2_CH1IN_1 | GPIO_PULLUP)
|
||
#define GPIO_TIM2_CH2IN (GPIO_TIM2_CH2IN_1 | GPIO_PULLUP)
|
||
|
||
#endif /* __BOARDS_ARM_STM32F401RC_RS485_INCLUDE_BOARD_H */
|