| .. |
|
chip
|
Fix a copy and paste error concerning the CAN driver. In the file sam_matrix.h the define SAM_MATRIX_CAN0_OFFSET is set to the wrong value.
|
2016-05-06 04:02:28 -06:00 |
|
chip.h
|
SAMV7 EMAC: Fix alignment issue: RX buffers need to be invalidated. This means the alignment of buffers must be at least to the data cache line size at both ends of the buffer
|
2015-03-28 13:09:01 -06:00 |
|
Kconfig
|
This is a fix to a problem in the handling of the oneshot timer. Due to a wrong assumption concerning the behavior directly after the start of the timer/counter the function sam_oneshot_cancel(…) calculates the wrong remaining time. The code assumes that the counter register is zero directly after the start of the timer, but this is not true. To start the time/counter a software trigger is invoked, this trigger starts the timer/count and sets the counter register to zero, but the reset of the counter register is not performed instantly. According to the datasheet: “The counter can be reset by a trigger. In this case, the counter value passes to zero on the next valid edge of the selected clock.” Thus the counter is set to zero between 0 and USEC_PER_TICK microseconds after the clock was started.
|
2016-05-27 07:51:50 -06:00 |
|
Make.defs
|
Add the up_systemreset interface to the samv7 arch. The approach is slightly different in that: 1) It enables ARCH_HAVE_RESET and allows the user to set if, and for how long, to drive External nRST signal. It also does not contain a default board_reset, as that really should be done in the config's src if CONFIG_BOARDCTL_RESET is defined.
|
2016-05-23 17:05:02 -06:00 |
|
sam_allocateheap.c
|
Rename board_led_on to board_autoled_on
|
2015-11-01 09:07:06 -06:00 |
|
sam_clockconfig.c
|
SAMV71 and SAME70: Place the Main Oscillator Enable in the board.h
|
2016-03-04 12:31:54 -06:00 |
|
sam_clockconfig.h
|
SAMV7 USB: USB must be enabled before PMC 480MHz clock is enabled
|
2015-08-11 15:48:26 -06:00 |
|
sam_config.h
|
Remove CONFIG_USARTn_ISUART
|
2016-05-25 11:21:48 -06:00 |
|
sam_emac.c
|
Replace irqsave() with enter_critical_section(); replace irqrestore() with leave_critical_section()
|
2016-02-13 19:11:09 -06:00 |
|
sam_ethernet.c
|
SAMV7: Quick'n'dirty port of the SAMA5D4 Ethernet MAC driver to the SAMV7. Still some unresovled issues with DCache handling
|
2015-03-16 13:51:37 -06:00 |
|
sam_ethernet.h
|
SAMV7: Add a sneak internal interface that will allow us to set the MAC address before NSH even starts
|
2015-03-18 17:23:40 -06:00 |
|
sam_freerun.c
|
Replace irqsave() with enter_critical_section(); replace irqrestore() with leave_critical_section()
|
2016-02-13 19:11:09 -06:00 |
|
sam_freerun.h
|
SAM3/4, SAMA5, SAMv7 Tickless: Refuse to call lower-level timer logic if not yet initialized
|
2016-02-05 10:22:11 -06:00 |
|
sam_gpio.c
|
Fix build if the config is not updated
|
2016-05-19 12:44:58 -10:00 |
|
sam_gpio.h
|
Adds a JTAG config and ERASE config to Kconfig to set the CCFG_SYSIO SYSIO Pins
|
2016-05-19 14:33:54 -06:00 |
|
sam_gpioirq.c
|
Correct some spacing issues
|
2015-10-07 11:39:06 -06:00 |
|
sam_hsmci_clkdiv.c
|
Remove executable flag from more .c and .h files
|
2015-04-09 08:20:57 -06:00 |
|
sam_hsmci.c
|
Cosmetic: Remove some harmless kruft left in last commit
|
2016-02-22 16:58:42 -06:00 |
|
sam_hsmci.h
|
Make some file section headers more consistent with standard
|
2015-04-08 08:04:12 -06:00 |
|
sam_irq.c
|
ARM: Fix missing header file. Update comments in all *_irq.c files.
|
2016-03-09 15:08:58 -06:00 |
|
sam_lowputc.c
|
Backing out part of last commit
|
2016-05-19 15:46:07 -06:00 |
|
sam_lowputc.h
|
Make some file section headers more consistent with standard
|
2015-04-08 08:04:12 -06:00 |
|
sam_mcan.c
|
SAMV7: MCAN: fix missing unlock of device in mcan_txempty
|
2016-06-01 10:38:19 -06:00 |
|
sam_mcan.h
|
Standardize the width of all comment boxes in header files
|
2015-10-02 17:47:23 -06:00 |
|
sam_mpuinit.c
|
Rename CONFIG_ARMV7M_MPU to CONFIG_ARM_MPU so that we can reuse the configuration settings for the ARMV7R MPU
|
2015-12-14 13:56:21 -06:00 |
|
sam_mpuinit.h
|
Rename CONFIG_ARMV7M_MPU to CONFIG_ARM_MPU so that we can reuse the configuration settings for the ARMV7R MPU
|
2015-12-14 13:56:21 -06:00 |
|
sam_oneshot.c
|
This is a fix to a problem in the handling of the oneshot timer. Due to a wrong assumption concerning the behavior directly after the start of the timer/counter the function sam_oneshot_cancel(…) calculates the wrong remaining time. The code assumes that the counter register is zero directly after the start of the timer, but this is not true. To start the time/counter a software trigger is invoked, this trigger starts the timer/count and sets the counter register to zero, but the reset of the counter register is not performed instantly. According to the datasheet: “The counter can be reset by a trigger. In this case, the counter value passes to zero on the next valid edge of the selected clock.” Thus the counter is set to zero between 0 and USEC_PER_TICK microseconds after the clock was started.
|
2016-05-27 07:51:50 -06:00 |
|
sam_oneshot.h
|
Cosmetic fix to spacing
|
2016-05-29 08:25:05 -06:00 |
|
sam_pck.c
|
SAMV7: Add support for PCK6 as a timer/counter clock source
|
2015-12-04 10:49:20 -06:00 |
|
sam_pck.h
|
SAMV7: Extend programmable clock support for queries about the PCK configuration
|
2015-12-03 14:11:39 -06:00 |
|
sam_periphclks.h
|
arch/arm/src/samv7: Add SAME70 memory map
|
2015-11-14 12:01:28 -06:00 |
|
sam_progmem.c
|
arch/arm/src/samv7: Add SAME70 memory map
|
2015-11-14 12:01:28 -06:00 |
|
sam_progmem.h
|
SAMV7 flash logic is complete, uncompiled, and untested
|
2015-11-12 10:46:59 -06:00 |
|
sam_qspi.c
|
Trivial simplification to logic of last commit
|
2015-11-11 15:17:36 -06:00 |
|
sam_qspi.h
|
SAMV71 QSPI: Use new QSPI interface. Can't use SPI interface as planned; the hardware architectue is too different
|
2015-08-25 15:23:59 -06:00 |
|
sam_rswdt.c
|
SAM WDT: Rename up_wdginitialize() functions to something more appropriate for the internal OS interface.
|
2016-05-18 19:47:48 -06:00 |
|
sam_serial.c
|
Remove CONFIG_USARTn_ISUART
|
2016-05-25 11:21:48 -06:00 |
|
sam_spi_slave.c
|
Replace irqsave() with enter_critical_section(); replace irqrestore() with leave_critical_section()
|
2016-02-13 19:11:09 -06:00 |
|
sam_spi.c
|
SAMV7 SPI: Revise support for Peripheral Chip Select Decoding to address up to 15 slaved
|
2016-02-25 08:13:33 -06:00 |
|
sam_spi.h
|
SAMV7 SPI: Revise support for Peripheral Chip Select Decoding to address up to 15 slaved
|
2016-02-25 08:13:33 -06:00 |
|
sam_ssc.c
|
Replace irqsave() with enter_critical_section(); replace irqrestore() with leave_critical_section()
|
2016-02-13 19:11:09 -06:00 |
|
sam_ssc.h
|
SAMV71: Quick'n'dirty port of the SAMA5 SSC driver to the SAM7. The IP is compatible but there are still some DMA- and Cache-related issues that need to be worked out.
|
2015-03-12 16:00:38 -06:00 |
|
sam_start.c
|
Fix build if the config is not updated
|
2016-05-19 12:44:58 -10:00 |
|
sam_start.h
|
Make some file section headers more consistent with standard
|
2015-04-08 08:04:12 -06:00 |
|
sam_systemreset.c
|
Restore PR. I have no idea where it went.
|
2016-05-23 17:45:15 -06:00 |
|
sam_tc.c
|
Fix what I believe to be typos in SAMV7 timer
|
2016-03-08 17:26:01 -06:00 |
|
sam_tc.h
|
SAMV7: Add support for PCK6 as a timer/counter clock source
|
2015-12-04 10:49:20 -06:00 |
|
sam_tickless.c
|
This is a fix to a problem in the handling of the oneshot timer. Due to a wrong assumption concerning the behavior directly after the start of the timer/counter the function sam_oneshot_cancel(…) calculates the wrong remaining time. The code assumes that the counter register is zero directly after the start of the timer, but this is not true. To start the time/counter a software trigger is invoked, this trigger starts the timer/count and sets the counter register to zero, but the reset of the counter register is not performed instantly. According to the datasheet: “The counter can be reset by a trigger. In this case, the counter value passes to zero on the next valid edge of the selected clock.” Thus the counter is set to zero between 0 and USEC_PER_TICK microseconds after the clock was started.
|
2016-05-27 07:51:50 -06:00 |
|
sam_timerisr.c
|
Costmetic fixes to C coding style
|
2015-10-05 17:13:53 -06:00 |
|
sam_trng.c
|
SAMV7: Port SAMAD5 TRNG driver to the SAMV7
|
2015-12-06 08:53:31 -06:00 |
|
sam_trng.h
|
SAMV7: Port SAMAD5 TRNG driver to the SAMV7
|
2015-12-06 08:53:31 -06:00 |
|
sam_twihs.c
|
This patch ensures that the TWIHS (i2c) hw get's its clock set when the sequence of
|
2016-05-23 13:38:34 -06:00 |
|
sam_twihs.h
|
Rename up_i2c initialize and uninitialize functions using the correct MCU-specific naming
|
2016-02-02 12:08:23 -06:00 |
|
sam_usbdev.h
|
SAMV7: A little more USB-related stuff
|
2015-03-21 08:54:01 -06:00 |
|
sam_usbdevhs.c
|
SAMV7: USBHS: Remove disabling of whole usb on suspend
|
2016-05-25 07:20:48 -06:00 |
|
sam_userspace.c
|
SAMV7 protected mode: Don't enable D-Cache until userspace data has been initialized
|
2015-11-07 09:35:23 -06:00 |
|
sam_userspace.h
|
Make some file section headers more consistent with standard
|
2015-04-08 08:04:12 -06:00 |
|
sam_wdt.c
|
SAM WDT: Rename up_wdginitialize() functions to something more appropriate for the internal OS interface.
|
2016-05-18 19:47:48 -06:00 |
|
sam_wdt.h
|
SAM WDT: Rename up_wdginitialize() functions to something more appropriate for the internal OS interface.
|
2016-05-18 19:47:48 -06:00 |
|
sam_xdmac.c
|
SAM (all): Fix several places in DMA logic where a spurious semicolon causes bad conditional logic
|
2016-05-11 17:26:59 -06:00 |
|
sam_xdmac.h
|
SAMV7 XDMAC: Don't sample interrupt status registers in debug mode. This can cause loss of interrupts
|
2015-11-07 11:25:20 -06:00 |
|
same70_periphclks.h
|
arch/arm/src/samv7: Add SAME70 memory map
|
2015-11-14 12:01:28 -06:00 |
|
samv71_periphclks.h
|
arch/arm/src/samv7: Add support for SAME70 peripheral clocks
|
2015-11-14 11:41:53 -06:00 |
