109 lines
3.2 KiB
Plaintext
109 lines
3.2 KiB
Plaintext
README
|
|
^^^^^^
|
|
|
|
README for NuttX port to NXP's PNEV5180B, which is a development board
|
|
containing a NXP-LPC1769 MCU and a PN5180 NFC Frontend.
|
|
|
|
Contents
|
|
^^^^^^^^
|
|
|
|
NXP's PNEV5180B Board
|
|
Configurations
|
|
|
|
NXP's PNEV5180B Board
|
|
^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
Pin Description On Board Connector
|
|
-------------------------------- ---------------- -------------
|
|
P0.2/TXD0/AD0.7 TX J201
|
|
P0.3/RXD0/AD0.6 RX
|
|
P0.22/RTS1/TD1 LD200 ORANGE LED
|
|
P0.15/TXD1/SCK0/SCK PN5180-SCK
|
|
P0.16/RXD1/SSEL0/SSEL PN5180-SSEL PN5180
|
|
P0.17/CTS1/MISO0/MISO PN5180-MISO
|
|
P0.18/DCD1/M0SI0/MOSI PN5180-MOSI
|
|
P0.19/DSR1/SDA1 EEPROM (Not Assembled)
|
|
P0.20/DTR1/SCL1 EEPROM
|
|
P0.21/RI1/RD1 PN5180-AUX2 PN5180
|
|
P0.29/USB_D+ USB-D+ USB
|
|
P0.30/USB_D- USB-D-
|
|
P2.0/PWM1.1/TXD1 LD201 RED LED
|
|
P2.5/PWM1.6/DTR1/TRACEDATA0 PN5180-nPN_RST
|
|
P2.9/USB_CONNECT/RXD2 USB_CONNECT USB
|
|
P2.11/nEINT1/I2STX_CLK PN5180-BUSY PN5180
|
|
P2.12/nEINT2/I2STX_WS PN5180-IRQ
|
|
P3.25/MAT0.0/PWM1.2 LD203 GREEN LED
|
|
P3.26/STCLK/MAT0.1/PWM1.3 LD202 BLUE LED
|
|
|
|
NXP's PNEV5180B Board
|
|
^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
UART
|
|
----
|
|
|
|
Board LPC1769
|
|
Signal Pin
|
|
----------------- -----------------
|
|
TX P0.2 TXD0
|
|
RX P0.3 RXD0
|
|
|
|
USB
|
|
---
|
|
|
|
Board LPC1769
|
|
Signal Pin
|
|
----------------- -----------------
|
|
USB_CONNECT P2.9 USB_CONNECT
|
|
USB_DM P0.29 USB_D-
|
|
USB_DP P0.30 USB_D+
|
|
|
|
PN5180
|
|
------
|
|
|
|
Board LPC1769
|
|
Signal Pin
|
|
----------------- -----------------
|
|
PN5180_SCK P0.15 SCK
|
|
PN5180_SSEL P0.16 SSEL
|
|
PN5180_MISO P0.17 MISO
|
|
PN5180_MOSI P0.18 MOSI
|
|
PN5180_AUX2 P0.21 GPIO I
|
|
PN5180_nPN_RST P2.5 GPIO O
|
|
PN5180_BUSY P2.11 GPIO I
|
|
PN5180_IRQ P2.12 GPIO I
|
|
|
|
Configurations
|
|
^^^^^^^^^^^^^^
|
|
|
|
Each PNEV5180B configuration is maintained in a sub-directory and can be
|
|
selected as follow:
|
|
|
|
cd tools
|
|
./configure.sh pnev5180b/<subdir>
|
|
cd -
|
|
|
|
Where <subdir> is one of the following:
|
|
|
|
nsh:
|
|
Configures the NuttShell (nsh) located at apps/system/nsh. The
|
|
Configuration enables the serial NSH interface.
|
|
|
|
NOTES:
|
|
|
|
1. This configuration uses the mconf-based configuration tool. To
|
|
change this configurations using that tool, you should:
|
|
|
|
a. Build and install the kconfig-mconf tool. See nuttx/README.txt
|
|
see additional README.txt files in the NuttX tools repository.
|
|
|
|
b. Execute 'make menuconfig' in nuttx/ in order to start the
|
|
reconfiguration process.
|
|
|
|
usbnsh:
|
|
Configures the NuttShell (nsh) located at apps/system/nsh. The
|
|
Configuration enables the CDC/ACM based NSH interface on /dev/ttyACM0.
|
|
|
|
nsh-cdcecm:
|
|
Configures the NuttShell (nsh) to provide a terminal on UART0. The
|
|
Configuration also provides network interface eth0 via CDC/ECM.
|