95abf562f4
added Sourcery CodeBench Lite for MIPS ELF Toolchain option; corrected inaccuracies in Photon board and EMW3162 board README.txt files.
83 lines
2.2 KiB
Plaintext
83 lines
2.2 KiB
Plaintext
README
|
|
======
|
|
|
|
EMW3162 board (https://www.waveshare.com/EMW3162.htm) features the
|
|
STM32F205RG MCU and Broadcom BCM43362KUBG Wi-Fi chip.
|
|
The STM32F205RG is a 120 MHz Cortex-M3 operation with 1MB Flash
|
|
memory and 128KB RAM.
|
|
|
|
Contents
|
|
========
|
|
|
|
- Configuring NuttX for the EMW3162 board
|
|
- Configuring NuttX to use your Wireless Router (aka Access Point)
|
|
- Programming Flash
|
|
- NSH via telnet
|
|
- Serial console configuration
|
|
|
|
Configuring NuttX for the EMW3162 board
|
|
=======================================
|
|
|
|
$ cd nuttx
|
|
$ make apps_distclean
|
|
$ make distclean
|
|
$ ./tools/configure.sh emw3162:wlan
|
|
|
|
Configuring NuttX to use your Wireless Router (aka Access Point)
|
|
================================================================
|
|
|
|
$ make menuconfig
|
|
|
|
Browse the menus this way:
|
|
|
|
Application Configuration --->
|
|
NSH Library --->
|
|
Networking Configuration --->
|
|
WAPI Configuration --->
|
|
(myApSSID) SSID
|
|
(mySSIDpassphrase) Passprhase
|
|
|
|
Replace the SSID from myApSSID with your wireless router name and
|
|
the Passprhase with your WiFi password.
|
|
|
|
Exit and save.
|
|
|
|
Finally just compile NuttX:
|
|
|
|
$ make
|
|
|
|
Programming Flash
|
|
=================
|
|
|
|
Flash memory can be programmed by stlink toolset
|
|
(https://github.com/stlink-org/stlink) and ST-LINK V2 programmer
|
|
(via SWD interface) as follows:
|
|
|
|
$ sudo st-flash write nuttx.bin 0x8000000
|
|
|
|
NSH via telnet
|
|
==============
|
|
|
|
After you successfully downloaded nuttx.bin, reset the board and it
|
|
automatically connects to the corresponding wifi AP. You may login
|
|
your router to see its IP address. Assume that it's 192.168.1.111
|
|
|
|
Open a terminal on your computer and telnet your EMW3162 board:
|
|
|
|
$ telnet 192.168.1.111
|
|
Trying 192.168.1.111...
|
|
Connected to 192.168.1.111.
|
|
Escape character is '^]'
|
|
|
|
NuttShell (NSH) NuttX-10.1.0-RC1
|
|
nsh>
|
|
|
|
Serial console configuration
|
|
============================
|
|
|
|
Connect a USB/Serial 3.3V dongle to GND, TXD and RXD pins of EMW3162 board.
|
|
Then use some serial console client (minicom, picocom, teraterm, etc) confi-
|
|
gured to 115200 8n1 without software or hardware flow control.
|
|
|
|
Reset the board and you should see NuttX starting in the serial.
|