sergiotarxz/nuttx
sergiotarxz/nuttx
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
nuttx/boards/arm/stm32/shenzhou/src/shenzhou.h
Alin Jerpelea 1ad3a22ad5 board: stm32: Author Gregory Nutt: update licenses to Apache 
Gregory Nutt has submitted the SGA and we can migrate the licenses
 to Apache.

Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
2021-03-20 19:22:58 -07:00

518 lines
21 KiB
C
Raw Blame History

/****************************************************************************
* boards/arm/stm32/shenzhou/src/shenzhou.h
*
* Licensed to the Apache Software Foundation (ASF) under one or more
* contributor license agreements. See the NOTICE file distributed with
* this work for additional information regarding copyright ownership. The
* ASF licenses this file to you under the Apache License, Version 2.0 (the
* "License"); you may not use this file except in compliance with the
* License. You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
* License for the specific language governing permissions and limitations
* under the License.
*
****************************************************************************/
#ifndef __BOARDS_ARM_STM32_SHENZHOUL_SRC_SHENZHOU_H
#define __BOARDS_ARM_STM32_SHENZHOUL_SRC_SHENZHOU_H
/****************************************************************************
* Included Files
****************************************************************************/
#include <nuttx/config.h>
#include <nuttx/compiler.h>
#include <stdint.h>
/****************************************************************************
* Pre-processor Definitions
****************************************************************************/
/* Configuration ************************************************************/
/* How many SPI modules does this chip support? */
#if STM32_NSPI < 1
# undef CONFIG_STM32_SPI1
# undef CONFIG_STM32_SPI2
# undef CONFIG_STM32_SPI3
#elif STM32_NSPI < 2
# undef CONFIG_STM32_SPI2
# undef CONFIG_STM32_SPI3
#elif STM32_NSPI < 3
# undef CONFIG_STM32_SPI3
#endif
/* Shenzhou GPIO Configuration **********************************************/
/* STM3240G-EVAL GPIOs ******************************************************/
/* Ethernet
*
* -- ---- -------------- ---------------------------------------------------
* PN NAME SIGNAL NOTES
* -- ---- -------------- ---------------------------------------------------
* 24 PA1 MII_RX_CLK Ethernet PHY NOTE: Despite the MII labeling of
* RMII_REF_CLK Ethernet PHY these signals, the DM916AEP is
* 25 PA2 MII_MDIO Ethernet PHY actually configured to work in RMII
* 48 PB11 MII_TX_EN Ethernet PHY mode.
* 51 PB12 MII_TXD0 Ethernet PHY
* 52 PB13 MII_TXD1 Ethernet PHY
* 16 PC1 MII_MDC Ethernet PHY
* 34 PC5 MII_INT Ethernet PHY
* 55 PD8 MII_RX_DV Ethernet PHY. Requires CONFIG_STM32_ETH_REMAP
* 55 PD8 RMII_CRSDV Ethernet PHY. Requires CONFIG_STM32_ETH_REMAP
* 56 PD9 MII_RXD0 Ethernet PHY. Requires CONFIG_STM32_ETH_REMAP
* 57 PD10 MII_RXD1 Ethernet PHY. Requires CONFIG_STM32_ETH_REMAP
*
* The board desdign can support a 50MHz external clock to drive the PHY
* (U9). However, on my board, U9 is not present.
*
* 67 PA8 MCO DM9161AEP
*/
#ifdef CONFIG_STM32_ETHMAC
# define GPIO_MII_INT (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_EXTI|GPIO_PORTC|GPIO_PIN5)
#endif
/* Wireless
*
* -- ---- -------------- ---------------------------------------------------
* PN NAME SIGNAL NOTES
* -- ---- -------------- ---------------------------------------------------
* 26 PA3 315M_VT
* 17 PC2 WIRELESS_INT
* 18 PC3 WIRELESS_CE To the NRF24L01 2.4G wireless module
* 59 PD12 WIRELESS_CS To the NRF24L01 2.4G wireless module
*/
#define GPIO_WIRELESS_CS (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTD|GPIO_PIN12)
/* Buttons
*
* -- ---- -------------- ---------------------------------------------------
* PN NAME SIGNAL NOTES
* -- ---- -------------- ---------------------------------------------------
* 23 PA0 WAKEUP Connected to KEY4. Active low: Closing KEY4 pulls
* WAKEUP to ground.
* 47 PB10 USERKEY Connected to KEY2
* 33 PC4 USERKEY2 Connected to KEY1
* 7 PC13 TAMPER Connected to KEY3
*/
/* BUTTONS -- NOTE that all have EXTI interrupts configured */
#define MIN_IRQBUTTON BUTTON_KEY1
#define MAX_IRQBUTTON BUTTON_KEY4
#define NUM_IRQBUTTONS (BUTTON_KEY4 - BUTTON_KEY1 + 1)
#define GPIO_BTN_WAKEUP (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_EXTI|GPIO_PORTA|GPIO_PIN0)
#define GPIO_BTN_USERKEY (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_EXTI|GPIO_PORTB|GPIO_PIN10)
#define GPIO_BTN_USERKEY2 (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_EXTI|GPIO_PORTC|GPIO_PIN4)
#define GPIO_BTN_TAMPER (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_EXTI|GPIO_PORTC|GPIO_PIN13)
/* LEDs
*
* -- ---- -------------- ---------------------------------------------------
* PN NAME SIGNAL NOTES
* -- ---- -------------- ---------------------------------------------------
* 83 PD2 LED1 Active low: Pulled high
* 84 PD3 LED2 Active low: Pulled high
* 85 PD4 LED3 Active low: Pulled high
* 88 PD7 LED4 Active low: Pulled high
*/
#define GPIO_LED1 (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTD|GPIO_PIN2)
#define GPIO_LED2 (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTD|GPIO_PIN3)
#define GPIO_LED3 (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTD|GPIO_PIN4)
#define GPIO_LED4 (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTD|GPIO_PIN7)
/* TFT LCD
*
* -- ---- -------------- ---------------------------------------------------
* PN NAME SIGNAL NOTES
* -- ---- -------------- ---------------------------------------------------
* 37 PB2 DATA_LE To TFT LCD. (CN13, ping 28)
* 96 PB9 F_CS To both the TFT LCD (CN13, pin 30) and to the
* W25X16 SPI FLASH
* 34 PC5 TP_INT JP6. To TFT LCD (CN13) module (CN13, pin 26)
* 65 PC8 LCD_CS Active low: Pulled high (CN13, pin 19)
* 66 PC9 TP_CS Active low: Pulled high (CN13, pin 31)
* 78 PC10 SPI3_SCK To TFT LCD (CN13, pin 29)
* 79 PC11 SPI3_MISO To TFT LCD (CN13, pin 25)
* 80 PC12 SPI3_MOSI To TFT LCD (CN13, pin 27)
* 58 PD11 SD_CS Active low: Pulled high
* (See also TFT LCD CN13, pin 32)
* 60 PD13 LCD_RS To TFT LCD (CN13, pin 20)
* 61 PD14 LCD_WR To TFT LCD (CN13, pin 21).
* Schematic is wrong LCD_WR is PB14.
* 62 PD15 LCD_RD To TFT LCD (CN13, pin 22)
* 97 PE0 DB00 To TFT LCD (CN13, pin 3)
* 98 PE1 DB01 To TFT LCD (CN13, pin 4)
* 1 PE2 DB02 To TFT LCD (CN13, pin 5)
* 2 PE3 DB03 To TFT LCD (CN13, pin 6)
* 3 PE4 DB04 To TFT LCD (CN13, pin 7)
* 4 PE5 DB05 To TFT LCD (CN13, pin 8)
* 5 PE6 DB06 To TFT LCD (CN13, pin 9)
* 38 PE7 DB07 To TFT LCD (CN13, pin 10)
* 39 PE8 DB08 To TFT LCD (CN13, pin 11)
* 40 PE9 DB09 To TFT LCD (CN13, pin 12)
* 41 PE10 DB10 To TFT LCD (CN13, pin 13)
* 42 PE11 DB11 To TFT LCD (CN13, pin 16)
* 43 PE12 DB12 To TFT LCD (CN13, pin 15)
* 44 PE13 DB13 To TFT LCD (CN13, pin 16)
* 45 PE14 DB14 To TFT LCD (CN13, pin 17)
* 46 PE15 DB15 To TFT LCD (CN13, pin 18)
*
* NOTE: The backlight signl NC_BL (CN13, pin 24) is pulled high and not
* under software control
*
* On LCD module:
* -- -------------- --------------------------------------------------------
* PN SIGNAL NOTES
* -- -------------- --------------------------------------------------------
* 3 DB01 To LCD DB1
* 4 DB00 To LCD DB0
* 5 DB03 To LCD DB3
* 6 DB02 To LCD DB2
* 7 DB05 To LCD DB5
* 8 DB04 To LCD DB4
* 9 DB07 To LCD DB7
* 10 DB06 To LCD DB6
* 11 DB09 To LCD DB9
* 12 DB08 To LCD DB8
* 13 DB11 To LCD DB11
* 14 DB10 To LCD DB10
* 15 DB13 To LCD DB13
* 16 DB12 To LCD DB12
* 17 DB15 To LCD DB15
* 18 DB14 To LCD DB14
* 19 RS To LCD RS
* 20 /LCD_CS To LCD CS
* 21 /RD To LCD RD
* 22 /WR To LCD WR
* 23 BL_EN (Not referenced)
* 24 /RESET
* 25 /INT To Touch IC /INT
* 26 MISO To Touch IC DOUT; To AT45DB161B SO; To SD card DAT0
* 27 LE To 74HC573 that controls LCD 8-bit/16-bit mode
* 28 MOSI To Touch IC DIN; To AT45DB161B SI; To SD card CMD
* 29 /DF_CS To AT45DB161B Data Flash /CS
* 30 SCLK To Touch IC DCLK; To AT45DB161B SCK; To SD card CLK
* 31 /SD_CS To SD card /CS
* 31 /TP_CS To Touch IC CS
*/
/* TFT LCD GPIOs */
#define GPIO_LCD_D0OUT (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN0)
#define GPIO_LCD_D1OUT (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN1)
#define GPIO_LCD_D2OUT (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN2)
#define GPIO_LCD_D3OUT (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN3)
#define GPIO_LCD_D4OUT (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN4)
#define GPIO_LCD_D5OUT (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN5)
#define GPIO_LCD_D6OUT (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN6)
#define GPIO_LCD_D7OUT (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN7)
#define GPIO_LCD_D8OUT (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN8)
#define GPIO_LCD_D9OUT (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN9)
#define GPIO_LCD_D10OUT (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN10)
#define GPIO_LCD_D11OUT (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN11)
#define GPIO_LCD_D12OUT (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN12)
#define GPIO_LCD_D13OUT (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN13)
#define GPIO_LCD_D14OUT (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN14)
#define GPIO_LCD_D15OUT (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN15)
#define GPIO_LCD_D0IN (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_PORTE|GPIO_PIN0)
#define GPIO_LCD_D1IN (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_PORTE|GPIO_PIN1)
#define GPIO_LCD_D2IN (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_PORTE|GPIO_PIN2)
#define GPIO_LCD_D3IN (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_PORTE|GPIO_PIN3)
#define GPIO_LCD_D4IN (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_PORTE|GPIO_PIN4)
#define GPIO_LCD_D5IN (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_PORTE|GPIO_PIN5)
#define GPIO_LCD_D6IN (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_PORTE|GPIO_PIN6)
#define GPIO_LCD_D7IN (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_PORTE|GPIO_PIN7)
#define GPIO_LCD_D8IN (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_PORTE|GPIO_PIN8)
#define GPIO_LCD_D9IN (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_PORTE|GPIO_PIN9)
#define GPIO_LCD_D10IN (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_PORTE|GPIO_PIN10)
#define GPIO_LCD_D11IN (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_PORTE|GPIO_PIN11)
#define GPIO_LCD_D12IN (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_PORTE|GPIO_PIN12)
#define GPIO_LCD_D13IN (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_PORTE|GPIO_PIN13)
#define GPIO_LCD_D14IN (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_PORTE|GPIO_PIN14)
#define GPIO_LCD_D15IN (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_PORTE|GPIO_PIN15)
#define GPIO_LCD_RS (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTD|GPIO_PIN13)
#define GPIO_LCD_CS (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTC|GPIO_PIN8)
#define GPIO_LCD_RD (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTD|GPIO_PIN15)
#define GPIO_LCD_WR (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN14)
#define GPIO_LCD_LE (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN2)
/* Bit band addresses */
#define STM32_GPIOB_OFFSET (STM32_GPIOB_BASE - STM32_PERIPH_BASE)
#define STM32_GPIOC_OFFSET (STM32_GPIOC_BASE - STM32_PERIPH_BASE)
#define STM32_GPIOD_OFFSET (STM32_GPIOD_BASE - STM32_PERIPH_BASE)
#define LCD_BIT_CLEAR(offs,pin) \
(STM32_PERIPHBB_BASE + ((offs + STM32_GPIO_BRR_OFFSET) << 5) + ((pin) << 2))
#define LCD_BIT_SET(offs,pin) \
(STM32_PERIPHBB_BASE + ((offs + STM32_GPIO_BSRR_OFFSET) << 5) + ((pin) << 2))
#define LCD_BIT_READ(offs,pin) \
(STM32_PERIPHBB_BASE + ((offs + STM32_GPIO_ODR_OFFSET) << 5) + ((pin) << 2))
#define LCD_RS_CLEAR LCD_BIT_CLEAR(STM32_GPIOD_OFFSET, 13) /* GPIO_PORTD|GPIO_PIN13 */
#define LCD_RS_SET LCD_BIT_SET(STM32_GPIOD_OFFSET, 13)
#define LCD_RS_READ LCD_BIT_READ(STM32_GPIOD_OFFSET, 13)
#define LCD_CS_CLEAR LCD_BIT_CLEAR(STM32_GPIOC_OFFSET, 8) /* GPIO_PORTC|GPIO_PIN8 */
#define LCD_CS_SET LCD_BIT_SET(STM32_GPIOC_OFFSET, 8)
#define LCD_CS_READ LCD_BIT_READ(STM32_GPIOC_OFFSET, 8)
#define LCD_RD_CLEAR LCD_BIT_CLEAR(STM32_GPIOD_OFFSET, 15) /* GPIO_PORTD|GPIO_PIN15 */
#define LCD_RD_SET LCD_BIT_SET(STM32_GPIOD_OFFSET, 15)
#define LCD_RD_READ LCD_BIT_READ(STM32_GPIOD_OFFSET, 15)
#define LCD_WR_CLEAR LCD_BIT_CLEAR(STM32_GPIOB_OFFSET, 14) /* GPIO_PORTB|GPIO_PIN14 */
#define LCD_WR_SET LCD_BIT_SET(STM32_GPIOB_OFFSET, 14)
#define LCD_WR_READ LCD_BIT_READ(STM32_GPIOB_OFFSET, 14)
#define LCD_LE_CLEAR LCD_BIT_CLEAR(STM32_GPIOB_OFFSET, 2) /* GPIO_PORTB|GPIO_PIN2 */
#define LCD_LE_SET LCD_BIT_SET(STM32_GPIOB_OFFSET, 2)
#define LCD_LE_READ LCD_BIT_READ(STM32_GPIOB_OFFSET, 2)
#define LCD_CRL STM32_GPIOE_CRL
#define LCD_CRH STM32_GPIOE_CRH
#define LCD_INPUT 0x44444444 /* Floating input */
#define LCD_OUTPUT 0x33333333 /* Push/pull output */
#define LCD_ODR STM32_GPIOE_ODR
#define LCD_IDR STM32_GPIOE_IDR
/* Touchscreen IC on the LCD module */
#define GPIO_TP_INT (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_EXTI|GPIO_PORTC|GPIO_PIN5)
#define GPIO_TP_CS (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTC|GPIO_PIN9)
/* AT45DB161B Data Flash on the LCD module */
#define GPIO_LCDDF_CS (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN9)
/* SD card on the LCD module */
#define GPIO_LCDSD_CS (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTD|GPIO_PIN11)
/* RS-485
*
* -- ---- -------------- ---------------------------------------------------
* PN NAME SIGNAL NOTES
* -- ---- -------------- ---------------------------------------------------
* 88 PD7 485_DIR SP3485 read enable (not)
*/
/* To be provided */
/* USB
*
* -- ---- -------------- ---------------------------------------------------
* PN NAME SIGNAL NOTES
* -- ---- -------------- ---------------------------------------------------
* 95 PB8 USB_PWR Drives USB VBUS
*/
#define GPIO_OTGFS_PWRON (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_SPEED_100MHz|\
GPIO_PUSHPULL|GPIO_PORTB|GPIO_PIN8)
/* Audio DAC
*
* -- ---- -------------- ---------------------------------------------------
* PN NAME SIGNAL NOTES
* -- ---- -------------- ---------------------------------------------------
*/
/* To be provided */
/* SPI FLASH
*
* -- ---- -------------- ---------------------------------------------------
* PN NAME SIGNAL NOTES
* -- ---- -------------- ---------------------------------------------------
* 96 PB9 F_CS To both the TFT LCD (CN13) and to the
* W25X16 SPI FLASH
*/
#define GPIO_FLASH_CS (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTB|GPIO_PIN9)
/* SD Card
*
* -- ---- -------------- ---------------------------------------------------
* PN NAME SIGNAL NOTES
* -- ---- -------------- ---------------------------------------------------
* 53 PB14 SD_CD Active low: Pulled high.
* Schematic is wrong LCD_WR is PB14.
* 58 PD11 SD_CS Active low: Pulled high
* (See also TFT LCD CN13, pin 32)
*/
#define GPIO_SD_CD (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_EXTI|GPIO_PORTB|GPIO_PIN14)
#define GPIO_SD_CS (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTD|GPIO_PIN11)
/* Relays */
#define NUM_RELAYS 2
#define GPIO_RELAYS_R00 (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN0)
#define GPIO_RELAYS_R01 (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTE|GPIO_PIN1)
/****************************************************************************
* Public Types
****************************************************************************/
/****************************************************************************
* Public Data
****************************************************************************/
#ifndef __ASSEMBLY__
/****************************************************************************
* Public Functions Definitions
****************************************************************************/
/****************************************************************************
* Name: stm32_spidev_initialize
*
* Description:
* Called to configure SPI chip select GPIO pins for the STM3240G-EVAL
* board.
*
****************************************************************************/
void weak_function stm32_spidev_initialize(void);
/****************************************************************************
* Name: stm32_usbinitialize
*
* Description:
* Called from stm32_usbinitialize very early in initialization to setup
* USB-related GPIO pins for the STM3240G-EVAL board.
*
****************************************************************************/
#ifdef CONFIG_STM32_OTGFS
void weak_function stm32_usbinitialize(void);
#endif
/****************************************************************************
* Name: stm32_usbhost_initialize
*
* Description:
* Called at application startup time to initialize the USB host
* functionality. This function will start a thread that will monitor for
* device connection/disconnection events.
*
****************************************************************************/
#if defined(CONFIG_STM32_OTGFS) && defined(CONFIG_USBHOST)
int stm32_usbhost_initialize(void);
#endif
/****************************************************************************
* Name: stm32_tsc_setup
*
* Description:
* This function is called by board-bringup logic to configure the
* touchscreen device. This function will register the driver as
* /dev/inputN where N is the minor device number.
*
* Input Parameters:
* minor - The input device minor number
*
* Returned Value:
* Zero is returned on success. Otherwise, a negated errno value is
* returned to indicate the nature of the failure.
*
****************************************************************************/
#ifdef CONFIG_INPUT_ADS7843E
int stm32_tsc_setup(int minor);
#endif
/****************************************************************************
* Name: stm32_adc_setup
*
* Description:
* Initialize ADC and register the ADC driver.
*
****************************************************************************/
#ifdef CONFIG_ADC
int stm32_adc_setup(void);
#endif
/****************************************************************************
* Name: stm32_can_setup
*
* Description:
* Initialize CAN and register the CAN device
*
****************************************************************************/
#ifdef CONFIG_CAN
int stm32_can_setup(void);
#endif
/****************************************************************************
* Name: stm32_sdinitialize
*
* Description:
* Initialize the SPI-based SD card. Requires CONFIG_DISABLE_MOUNTPOINT=n
* and CONFIG_STM32_SPI1=y
*
****************************************************************************/
int stm32_sdinitialize(int minor);
/****************************************************************************
* Name: stm32_w25initialize
*
* Description:
* Initialize and register the W25 FLASH file system.
*
****************************************************************************/
#ifdef CONFIG_MTD_W25
int stm32_w25initialize(int minor);
#endif
#endif /* __ASSEMBLY__ */
#endif /* __BOARDS_ARM_STM32_SHENZHOUL_SRC_SHENZHOU_H */
Reference in New Issue View Git Blame Copy Permalink