203 lines
6.3 KiB
C
203 lines
6.3 KiB
C
/****************************************************************************
|
|
* boards/arm/stm32wb/nucleo-wb55rg/include/board.h
|
|
*
|
|
* Licensed to the Apache Software Foundation (ASF) under one or more
|
|
* contributor license agreements. See the NOTICE file distributed with
|
|
* this work for additional information regarding copyright ownership. The
|
|
* ASF licenses this file to you under the Apache License, Version 2.0 (the
|
|
* "License"); you may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at
|
|
*
|
|
* http://www.apache.org/licenses/LICENSE-2.0
|
|
*
|
|
* Unless required by applicable law or agreed to in writing, software
|
|
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
|
|
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
|
|
* License for the specific language governing permissions and limitations
|
|
* under the License.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#ifndef __BOARDS_ARM_STM32WB_NUCLEO_WB55RG_INCLUDE_BOARD_H
|
|
#define __BOARDS_ARM_STM32WB_NUCLEO_WB55RG_INCLUDE_BOARD_H
|
|
|
|
/****************************************************************************
|
|
* Included Files
|
|
****************************************************************************/
|
|
|
|
#include <nuttx/config.h>
|
|
#ifndef __ASSEMBLY__
|
|
# include <stdint.h>
|
|
#endif
|
|
|
|
/* Clocking *****************************************************************/
|
|
|
|
#include "nucleo-wb55rg.h"
|
|
|
|
/* Do not include STM32WB header files here */
|
|
|
|
/****************************************************************************
|
|
* Pre-processor Definitions
|
|
****************************************************************************/
|
|
|
|
/* DMA Channel/Stream Selections ********************************************/
|
|
|
|
/* Stream selections are arbitrary for now but might become important in the
|
|
* future is we set aside more DMA channels/streams.
|
|
*/
|
|
|
|
/* Values defined in arch/arm/src/stm32wb/hardware/stm32wb_dmamux.h */
|
|
|
|
#define DMAMAP_SPI1_RX DMAMAP_SPI1_RX_0 /* DMA1 */
|
|
#define DMAMAP_SPI1_TX DMAMAP_SPI1_TX_0 /* DMA1 */
|
|
|
|
/* UART RX DMA configurations */
|
|
|
|
#define DMAMAP_USART1_RX DMAMAP_USART1_RX_0 /* DMA1 */
|
|
|
|
/* ADC */
|
|
|
|
#define DMAMAP_ADC1 DMAMAP_ADC1_0 /* DMA1 */
|
|
|
|
/* Alternate function pin selections ****************************************/
|
|
|
|
/* USART */
|
|
|
|
#define GPIO_USART1_RX GPIO_USART1_RX_2 /* PB7 */
|
|
#define GPIO_USART1_TX GPIO_USART1_TX_2 /* PB6 */
|
|
|
|
/* LPUART */
|
|
|
|
#define GPIO_LPUART1_RX GPIO_LPUART1_RX_1 /* PA3 */
|
|
#define GPIO_LPUART1_TX GPIO_LPUART1_TX_1 /* PA2 */
|
|
|
|
/* I2C
|
|
*
|
|
* The optional _GPIO configurations allow the I2C driver to manually
|
|
* reset the bus to clear stuck slaves. They match the pin configuration,
|
|
* but are normally-high GPIOs.
|
|
*/
|
|
|
|
#define GPIO_I2C1_SCL (GPIO_I2C1_SCL_2 | GPIO_SPEED_50MHz | GPIO_OUTPUT_SET)
|
|
#define GPIO_I2C1_SDA (GPIO_I2C1_SDA_2 | GPIO_SPEED_50MHz | GPIO_OUTPUT_SET)
|
|
#define GPIO_I2C1_SCL_GPIO \
|
|
(GPIO_OUTPUT | GPIO_OPENDRAIN | GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | \
|
|
GPIO_PORTB | GPIO_PIN8)
|
|
#define GPIO_I2C1_SDA_GPIO \
|
|
(GPIO_OUTPUT | GPIO_OPENDRAIN | GPIO_SPEED_50MHz | GPIO_OUTPUT_SET | \
|
|
GPIO_PORTB | GPIO_PIN9)
|
|
|
|
/* SPI */
|
|
|
|
#define GPIO_SPI1_NSS GPIO_SPI1_NSS_2 /* PB2 */
|
|
#define GPIO_SPI1_SCK GPIO_SPI1_SCK_2 /* PA5 */
|
|
#define GPIO_SPI1_MISO GPIO_SPI1_MISO_1 /* PA6 */
|
|
#define GPIO_SPI1_MOSI GPIO_SPI1_MOSI_1 /* PA7 */
|
|
|
|
/* LEDs
|
|
*
|
|
* The Nucleo WB55RG board provides three user LEDs.
|
|
*
|
|
* - When the I/O is HIGH value, the LED is on.
|
|
* - When the I/O is LOW, the LED is off.
|
|
*/
|
|
|
|
/* LED index values for use with board_userled() */
|
|
|
|
#define BOARD_LED1 0 /* PB5 */
|
|
#define BOARD_LED2 1 /* PB0 */
|
|
#define BOARD_LED3 2 /* PB1 */
|
|
#define BOARD_NLEDS 3
|
|
|
|
#define BOARD_LED_BLUE BOARD_LED1
|
|
#define BOARD_LED_GREEN BOARD_LED2
|
|
#define BOARD_LED_RED BOARD_LED3
|
|
|
|
/* LED bits for use with board_userled_all() */
|
|
|
|
#define BOARD_LED1_BIT (1 << BOARD_LED1)
|
|
#define BOARD_LED2_BIT (1 << BOARD_LED2)
|
|
#define BOARD_LED3_BIT (1 << BOARD_LED3)
|
|
|
|
/* These LEDs are not used by the board port unless CONFIG_ARCH_LEDS is
|
|
* defined. In that case, the usage by the board port is defined in
|
|
* include/board.h and src/stm32_autoleds.c.
|
|
*/
|
|
|
|
#define LED_STARTED 0
|
|
#define LED_HEAPALLOCATE 0
|
|
#define LED_IRQSENABLED 0
|
|
#define LED_STACKCREATED 1
|
|
#define LED_INIRQ 1
|
|
#define LED_SIGNAL 2
|
|
#define LED_ASSERTION 2
|
|
#define LED_PANIC 1
|
|
|
|
/* Buttons */
|
|
|
|
#define BUTTON_SW1 0 /* PC4, needs SB47 close */
|
|
#define BUTTON_SW2 1 /* PD0 */
|
|
#define BUTTON_SW3 2 /* PD1 */
|
|
#define NUM_BUTTONS 3
|
|
|
|
#define BUTTON_SW1_BIT (1 << BUTTON_SW1)
|
|
#define BUTTON_SW2_BIT (1 << BUTTON_SW2)
|
|
#define BUTTON_SW3_BIT (1 << BUTTON_SW3)
|
|
|
|
/* Quadrature Encoder */
|
|
|
|
#define GPIO_TIM2_CH1IN GPIO_TIM2_CH1IN_1 /* PA0 */
|
|
#define GPIO_TIM2_CH2IN GPIO_TIM2_CH2IN_1 /* PA1 */
|
|
|
|
/* PWM output for full bridge */
|
|
|
|
#define GPIO_TIM1_CH1OUT GPIO_TIM1_CH1OUT_1 /* PA8 */
|
|
#define GPIO_TIM1_CH1NOUT GPIO_TIM1_CH1N_2 /* PB13 */
|
|
#define GPIO_TIM1_CH2OUT GPIO_TIM1_CH2OUT_1 /* PA9 */
|
|
#define GPIO_TIM1_CH2NOUT GPIO_TIM1_CH2N_2 /* PB14 */
|
|
|
|
/* LPTIM PWM */
|
|
|
|
#define GPIO_LPTIM1_CH1OUT GPIO_LPTIM1_OUT_3 /* PC1 */
|
|
#define GPIO_LPTIM2_CH1OUT GPIO_LPTIM2_OUT_1 /* PA4 */
|
|
|
|
/****************************************************************************
|
|
* Public Data
|
|
****************************************************************************/
|
|
|
|
#ifndef __ASSEMBLY__
|
|
|
|
#undef EXTERN
|
|
#if defined(__cplusplus)
|
|
#define EXTERN extern "C"
|
|
extern "C"
|
|
{
|
|
#else
|
|
#define EXTERN extern
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Public Function Prototypes
|
|
****************************************************************************/
|
|
|
|
/****************************************************************************
|
|
* Name: stm32wb_board_initialize
|
|
*
|
|
* Description:
|
|
* All STM32WB architectures must provide the following entry point.
|
|
* This entry point is called early in the initialization -- after all
|
|
* memory has been configured and mapped but before any devices have been
|
|
* initialized.
|
|
*
|
|
****************************************************************************/
|
|
|
|
void stm32wb_board_initialize(void);
|
|
|
|
#undef EXTERN
|
|
#if defined(__cplusplus)
|
|
}
|
|
#endif
|
|
|
|
#endif /* __ASSEMBLY__ */
|
|
#endif /* __BOARDS_ARM_STM32WB_NUCLEO_WB55RG_INCLUDE_BOARD_H */
|