nuttx/drivers/serial/Kconfig

#
# For a description of the syntax of this configuration file,
# see the file kconfig-language.txt in the NuttX tools repository.
#

config DEV_LOWCONSOLE
	bool "Low-level console support"
	default n
	depends on ARCH_LOWPUTC
	depends on DEV_CONSOLE
	---help---
		Use the simple, low-level, write-only serial console driver (minimal support)

config SERIAL_REMOVABLE
	bool
	default n

config SERIAL_CONSOLE
	bool
	default n

config SERIAL_SIGKILL_CHAR
	int "Serial parse SIGKILL characters"
	default 3 if SERIAL_CONSOLE
	default 4 if !SERIAL_CONSOLE
	depends on SIG_SIGKILL && BUILD_FLAT
	---help---
		Use ASCII 3 (Ctrl-c) or 4 (ctrl-d) inputs to determine whether to
		send a SIGKILL event.  Other charcters may also be selected.

		REVISIT:  Traditionally Ctrl-C would generate SIGINT.  Ctrl-D is the
		End-of-File character that should close the stream.

menuconfig 16550_UART
	bool "16550 UART Chip support"
	default n

if 16550_UART
source drivers/serial/Kconfig-16550
endif

#
# MCU serial peripheral driver?
#

config OTHER_UART_SERIALDRIVER
	bool
	default n
	select MCU_SERIAL

config MCU_SERIAL
	bool
	default n

#
# Standard serial driver configuration
#

config STANDARD_SERIAL
	bool "Enable standard \"upper-half\" serial driver"
	default y if MCU_SERIAL
	default n if !MCU_SERIAL
	depends on !DEV_LOWCONSOLE
	---help---
		Enable the standard, upper-half serial driver used by most MCU serial peripherals.

config SERIAL_NPOLLWAITERS
	int "Number of poll threads"
	default 2
	depends on !DISABLE_POLL && STANDARD_SERIAL
	---help---
		Maximum number of threads than can be waiting for POLL events.
		Default: 2

config SERIAL_IFLOWCONTROL
	bool
	default n

config SERIAL_OFLOWCONTROL
	bool
	default n

config SERIAL_DMA
	bool
	default n

config SERIAL_IFLOWCONTROL_WATERMARKS
	bool "RX flow control watermarks"
	default n
	depends on SERIAL_IFLOWCONTROL
	---help---
		Call the "lower half" rxflowcontrol method whenever the number of
		characters in the serial RX buffer falls above an upper water mark
		level or below a lower watermark level.  The default behavior is to
		call the rxflowcontrol method only when the RX buffer is empty or
		full.

if SERIAL_IFLOWCONTROL_WATERMARKS

config SERIAL_IFLOWCONTROL_LOWER_WATERMARK
	int "RX lower Watermark (percent)"
	default 10
	range 1 99
	---help---
		Call the rxflowcontrol method then there are this amount (or or less)
		data buffered in the serial drivers RX buffer.  This is expressed
		as a percentage of the total size of the RX buffer which may vary
		from instance-to-instance.

config SERIAL_IFLOWCONTROL_UPPER_WATERMARK
	int "RX upper Watermark (percent)"
	default 90
	range 1 99
	---help---
		Call the rxflowcontrol method then there are this amount (or more)
		data buffered in the serial drivers RX buffer.  This is expressed
		as a percentage of the total size of the RX buffer which may vary
		from instance-to-instance.

endif # SERIAL_IFLOWCONTROL_WATERMARKS

config SERIAL_TIOCSERGSTRUCT
	bool "Support TIOCSERGSTRUCT"
	default n
	depends on DEBUG_FEATURES && (MCU_SERIAL || 16550_UART)
	---help---
		As a debug option, many serial bottom half drivers support the TIOCSERGSTRUCT
		that allows you to get the internal driver data structure.  By default, this
		IOCTL is not supported in order to reduce footprint.  But if (1) the driver
		supports the TIOCSERGSTRUCT ioctl, and (2) this option is selected, then
		support for the TIOCSERGSTRUCT will be enabled.

config ARCH_HAVE_SERIAL_TERMIOS
	bool
	default n

config SERIAL_TERMIOS
	bool "Serial TERMIOS support"
	depends on ARCH_HAVE_SERIAL_TERMIOS
	default n
	---help---
		Serial driver supports termios.h interfaces (tcsetattr, tcflush, etc.).
		If this is not defined, then the terminal settings (baud, parity, etc).
		are not configurable at runtime; serial streams cannot be flushed, etc..

#
# Serial console selection
#

choice
	prompt "Serial console"
	default NO_SERIAL_CONSOLE if !OTHER_UART_SERIALDRIVER
	default OTHER_SERIAL_CONSOLE if OTHER_UART_SERIALDRIVER
	depends on MCU_SERIAL
	#depends on DEV_CONSOLE - We may have serial console with no file system at all

config UART_SERIAL_CONSOLE
	bool "UART"
	depends on UART_SERIALDRIVER
	select SERIAL_CONSOLE

config UART0_SERIAL_CONSOLE
	bool "UART0"
	depends on UART0_SERIALDRIVER
	select SERIAL_CONSOLE

config USART0_SERIAL_CONSOLE
	bool "USART0"
	depends on USART0_SERIALDRIVER
	select SERIAL_CONSOLE

config UART1_SERIAL_CONSOLE
	bool "UART1"
	depends on UART1_SERIALDRIVER
	select SERIAL_CONSOLE

config USART1_SERIAL_CONSOLE
	bool "USART1"
	depends on USART1_SERIALDRIVER
	select SERIAL_CONSOLE

config UART2_SERIAL_CONSOLE
	bool "UART2"
	depends on UART2_SERIALDRIVER
	select SERIAL_CONSOLE

config USART2_SERIAL_CONSOLE
	bool "USART2"
	depends on USART2_SERIALDRIVER
	select SERIAL_CONSOLE

config UART3_SERIAL_CONSOLE
	bool "UART3"
	depends on UART3_SERIALDRIVER
	select SERIAL_CONSOLE

config USART3_SERIAL_CONSOLE
	bool "USART3"
	depends on USART3_SERIALDRIVER
	select SERIAL_CONSOLE

config UART4_SERIAL_CONSOLE
	bool "UART4"
	depends on UART4_SERIALDRIVER
	select SERIAL_CONSOLE

config USART4_SERIAL_CONSOLE
	bool "USART4"
	depends on USART4_SERIALDRIVER
	select SERIAL_CONSOLE

config UART5_SERIAL_CONSOLE
	bool "UART5"
	depends on UART5_SERIALDRIVER
	select SERIAL_CONSOLE

config USART5_SERIAL_CONSOLE
	bool "USART5"
	depends on USART5_SERIALDRIVER
	select SERIAL_CONSOLE

config UART6_SERIAL_CONSOLE
	bool "UART6"
	depends on UART6_SERIALDRIVER
	select SERIAL_CONSOLE

config USART6_SERIAL_CONSOLE
	bool "USART6"
	depends on USART6_SERIALDRIVER
	select SERIAL_CONSOLE

config UART7_SERIAL_CONSOLE
	bool "UART7"
	depends on UART7_SERIALDRIVER
	select SERIAL_CONSOLE

config USART7_SERIAL_CONSOLE
	bool "USART7"
	depends on USART7_SERIALDRIVER
	select SERIAL_CONSOLE

config UART8_SERIAL_CONSOLE
	bool "UART8"
	depends on UART8_SERIALDRIVER
	select SERIAL_CONSOLE

config USART8_SERIAL_CONSOLE
	bool "USART8"
	depends on USART8_SERIALDRIVER
	select SERIAL_CONSOLE

config USART9_SERIAL_CONSOLE
	bool "USART8"
	depends on USART9_SERIALDRIVER
	select SERIAL_CONSOLE

config LPUART0_SERIAL_CONSOLE
	bool "LPUART0"
	depends on LPUART0_SERIALDRIVER
	select SERIAL_CONSOLE

config LPUART1_SERIAL_CONSOLE
	bool "LPUART1"
	depends on LPUART1_SERIALDRIVER
	select SERIAL_CONSOLE

config LPUART2_SERIAL_CONSOLE
	bool "LPUART2"
	depends on LPUART2_SERIALDRIVER
	select SERIAL_CONSOLE

config LPUART3_SERIAL_CONSOLE
	bool "LPUART3"
	depends on LPUART3_SERIALDRIVER
	select SERIAL_CONSOLE

config LPUART4_SERIAL_CONSOLE
	bool "LPUART4"
	depends on LPUART4_SERIALDRIVER
	select SERIAL_CONSOLE

config LPUART5_SERIAL_CONSOLE
	bool "LPUART5"
	depends on LPUART5_SERIALDRIVER
	select SERIAL_CONSOLE

config LPUART6_SERIAL_CONSOLE
	bool "LPUART6"
	depends on LPUART6_SERIALDRIVER
	select SERIAL_CONSOLE

config LPUART7_SERIAL_CONSOLE
	bool "LPUART7"
	depends on LPUART7_SERIALDRIVER
	select SERIAL_CONSOLE

config LPUART8_SERIAL_CONSOLE
	bool "LPUART8"
	depends on LPUART8_SERIALDRIVER
	select SERIAL_CONSOLE

config SCI0_SERIAL_CONSOLE
	bool "SCI0"
	depends on SCI0_SERIALDRIVER
	select SERIAL_CONSOLE

config SCI1_SERIAL_CONSOLE
	bool "SCI1"
	depends on SCI1_SERIALDRIVER
	select SERIAL_CONSOLE

config OTHER_SERIAL_CONSOLE
	bool "Other serial console"
	select SERIAL_CONSOLE

config NO_SERIAL_CONSOLE
	bool "No serial console"

endchoice

#
# U[S]ARTn_XYZ settings for MCU serial drivers
#

menu "UART Configuration"
	depends on UART_SERIALDRIVER

config UART_RXBUFSIZE
	int "Receive buffer size"
	default 256
	---help---
		Characters are buffered as they are received. This specifies
		the size of the receive buffer.

config UART_TXBUFSIZE
	int "Transmit buffer size"
	default 256
	---help---
		Characters are buffered before being sent.  This specifies
		the size of the transmit buffer.

config UART_BAUD
	int "BAUD rate"
	default 115200
	---help---
		The configured BAUD of the UART.

config UART_BITS
	int "Character size"
	default 8
	---help---
		The number of bits.  Must be either 7 or 8.

config UART_PARITY
	int "Parity setting"
	default 0
	range 0 2
	---help---
		0=no parity, 1=odd parity, 2=even parity

config UART_2STOP
	int "use 2 stop bits"
	default 0
	---help---
		1=Two stop bits

config UART_IFLOWCONTROL
	bool "UART RTS flow control"
	default n
	select SERIAL_IFLOWCONTROL
	---help---
		Enable UART RTS flow control

config UART_OFLOWCONTROL
	bool "UART CTS flow control"
	default n
	select SERIAL_OFLOWCONTROL
	---help---
		Enable UART CTS flow control

config UART_DMA
	bool "UART DMA support"
	default n
	select SERIAL_DMA
	---help---
		Enable DMA transfers on UART

endmenu

source drivers/serial/Kconfig-uart
source drivers/serial/Kconfig-lpuart
source drivers/serial/Kconfig-usart
source drivers/serial/Kconfig-sci

menuconfig PSEUDOTERM
	bool "Pseudo-Terminal (PTY) suppport"
	default n
	select PIPES
	select ARCH_HAVE_SERIAL_TERMIOS
	---help---
		Enable support support for master and slave pseudo-terminal devices.

if PSEUDOTERM

choice
	prompt "PTY model"
	default PSEUDOTERM_BSD if DISABLE_PSEUDOFS_OPERATIONS
	default PSEUDOTERM_SUSV1 if !DISABLE_PSEUDOFS_OPERATIONS

config PSEUDOTERM_BSD
	bool "BSD style"
	---help---
		Deprecated BSD style PTYs.

		Master: /dev/ptyN
		Slave: /dev/ttypN

		Where N is the minor number

config PSEUDOTERM_SUSV1
	bool "SUSv1 style"
	depends on !DISABLE_PSEUDOFS_OPERATIONS
	---help---
		PTYs as specified in the Single Unix Specification (SUSv1).

		Master: /dev/ptmx (multiplexor)
		Slave: /dev/pts/N

		Where N is the minor number

endchoice # PTY model

config PSEUDOTERM_RXBUFSIZE
	int "Pseudo-Terminal Rx buffer size"
	default 256
	---help---
		Master-to-slave pipe buffer size.  Default: 256

config PSEUDOTERM_TXBUFSIZE
	int "Pseudo-Terminal Tx buffer size"
	default 256
	---help---
		Slave-to-master pipe buffer size.  Default: 256

endif # PSEUDOTERM