sergiotarxz/nuttx
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
9ef481ce4b
nuttx/configs/dk-tm4c129x/README.txt
Gregory Nutt 22cd0d47fa This commit attempts remove some long standard confusion in naming and some actual problems that result from the naming confusion. The basic problem is the standard MTU does not include the size of the Ethernet header. For clarity, I changed the naming of most things called MTU to PKTSIZE. For example, CONFIG_NET_ETH_MTU is now CONFIG_NET_ETH_PKTSIZE. 
This makes the user interface a little hostile.  People thing of an MTU of 1500 bytes, but the corresponding packet is really 1514 bytes (including the 14 byte Ethernet header).  A more friendly solution would configure the MTU (as before), but then derive the packet buffer size by adding the MAC header length.  Instead, we define the packet buffer size then derive the MTU.

The MTU is not common currency in networking.  On the wire, the only real issue is the MSS which is derived from MTU by subtracting the IP header and TCP header sizes (for the case of TCP).  Now it is derived for the PKTSIZE by subtracting the IP header, the TCP header, and the MAC header sizes.  So we should be all good and without the recurring 14 byte error in MTU's and MSS's.

Squashed commit of the following:

    Trivial update to fix some spacing issues.
    net/: Rename several macros containing _MTU to _PKTSIZE.
    net/: Rename CONFIG_NET_SLIP_MTU to CONFIG_NET_SLIP_PKTSIZE and similarly for CONFIG_NET_TUN_MTU.  These are not the MTU which does not include the size of the link layer header.  These are the full size of the packet buffer memory (minus any GUARD bytes).
    net/: Rename CONFIG_NET_6LOWPAN_MTU to CONFIG_NET_6LOWPAN_PKTSIZE and similarly for CONFIG_NET_TUN_MTU.  These are not the MTU which does not include the size of the link layer header.  These are the full size of the packet buffer memory (minus any GUARD bytes).
    net/: Rename CONFIG_NET_ETH_MTU to CONFIG_NET_ETH_PKTSIZE.  This is not the MTU which does not include the size of the link layer header.  This is the full size of the packet buffer memory (minus any GUARD bytes).
    net/: Rename the file d_mtu in the network driver structure to d_pktsize.  That value saved there is not the MTU.  The packetsize is the memory large enough to hold the maximum packet PLUS the size of the link layer header.  The MTU does not include the link layer header.
2018-07-04 14:10:40 -06:00

830 lines
32 KiB
Plaintext
Raw Blame History

README.txt
==========
This README file discuss discusses the port of NuttX to the Texas
Instruments DK-TM4C129X Connected Development Kit.
Description
-----------
The Tiva™ C Series TM4C129X Connected Development Kit highlights
the 120-MHz Tiva C Series TM4C129XNCZAD ARM® Cortex™-M4 based
microcontroller, including an integrated 10/100 Ethernet MAC +
PHY as well as many other key features.
Features
--------
- Color LCD interface
- USB 2.0 OTG | Host | Device port
- TI wireless EM connection
- BoosterPack and BoosterPack XL interfaces
- Quad SSI-supported 512-Mbit Flash memory
- MicroSD slot
- Expansion interface headers: MCU high-speed USB ULPI port,
Ethernet RMII and MII ports External peripheral interface for
memories, parallel peripherals, and other system functions.
- In-Circuit Debug Interface (ICDI)
Contents
- Using OpenOCD and GDB with ICDI
- Buttons and LEDs
- Serial Console
- Networking Support
- Timers
- Temperature Sensor
- DK-TM4129X Configuration Options
- Configurations
Using OpenOCD and GDB with ICDI
===============================
Building OpenOCD under Cygwin:
Refer to configs/olimex-lpc1766stk/README.txt
Installing OpenOCD in Linux:
sudo apt-get install openocd
You can also build openocd from its source:
git clone http://git.code.sf.net/p/openocd/code openocd
cd openocd
Helper Scripts:
I have been using the on-board In-Circuit Debug Interface (ICDI) interface.
OpenOCD requires a configuration file. I keep the one I used last here:
configs/dk-tm4c129x/tools/dk-tm4c129x.cfg
However, the "correct" configuration script to use with OpenOCD may
change as the features of OpenOCD evolve. So you should at least
compare that dk-tm4c129x.cfg file with configuration files in
/usr/share/openocd/scripts. As of this writing, the configuration
files of interest were:
/usr/local/share/openocd/scripts/board/dk-tm4c129x.cfg
/usr/local/share/openocd/scripts/interface/ti-icdi.cfg
/usr/local/share/openocd/scripts/target/stellaris_icdi.cfg
There is also a script on the tools/ directory that I use to start
the OpenOCD daemon on my system called oocd.sh. That script will
probably require some modifications to work in another environment:
- Possibly the value of OPENOCD_PATH and TARGET_PATH
- It assumes that the correct script to use is the one at
configs/dk-tm4c129x/tools/dk-tm4c129x.cfg
Starting OpenOCD
If you are in the top-level NuttX build directlory then you should
be able to start the OpenOCD daemon like:
oocd.sh $PWD
Assuming that you have included the path to the oocd.sh script,
configs/dk-tm4c129x/tools, in PATH variable.
Note that OpenOCD needs to be run with administrator privileges in
some environments (sudo).
Connecting GDB
Once the OpenOCD daemon has been started, you can connect to it via
GDB using the following GDB command:
arm-nuttx-elf-gdb
(gdb) target remote localhost:3333
NOTE: The name of your GDB program may differ. For example, with the
CodeSourcery toolchain, the ARM GDB would be called arm-none-eabi-gdb.
After starting GDB, you can load the NuttX ELF file:
(gdb) symbol-file nuttx
(gdb) monitor reset
(gdb) monitor halt
(gdb) load nuttx
NOTES:
1. Loading the symbol-file is only useful if you have built NuttX to
include debug symbols (by setting CONFIG_DEBUG_SYMBOLS=y in the
.config file).
2. The MCU must be halted prior to loading code using 'mon reset'
as described below.
OpenOCD will support several special 'monitor' commands. These
GDB commands will send comments to the OpenOCD monitor. Here
are a couple that you will need to use:
(gdb) monitor reset
(gdb) monitor halt
NOTES:
1. The MCU must be halted using 'mon halt' prior to loading code.
2. Reset will restart the processor after loading code.
3. The 'monitor' command can be abbreviated as just 'mon'.
Buttons and LEDs
================
Buttons
-------
There are three push buttons on the board.
--- ------------ -----------------
Pin Pin Function Jumper
--- ------------ -----------------
PP1 Select SW4 J37 pins 1 and 2
PN3 Up SW2 J37 pins 3 and 4
PE5 Down SW3 J37 pins 5 and 6
--- ------------ -----------------
LEDs
----
The development board has one tri-color user LED.
--- ------------ -----------------
Pin Pin Function Jumper
--- ------------ -----------------
PN5 Red LED J36 pins 1 and 2
PQ4 Blue LED J36 pins 3 and 4
PQ7 Green LED J36 pins 5 and 6
--- ------------ -----------------
If CONFIG_ARCH_LEDS is not defined, this LED is not used by the NuttX
logic. APIs are provided to support application control of the LED in
that case (in include/board.h and src/tm4c_userleds.c).
If CONFIG_ARCH_LEDS is defined then the usage of the LEDs by Nuttx is
defined in include/board.h and src/tm4c_autoleds.c. The LEDs are used to
encode OS-related events as follows:
SYMBOL Meaning LED state
------------------- ----------------------- -------- --------
LED_STARTED NuttX has been started Blue
LED_HEAPALLOCATE Heap has been allocated (No change)
LED_IRQSENABLED Interrupts enabled (No change)
LED_STACKCREATED Idle stack created Green
LED_INIRQ In an interrupt (No change)
LED_SIGNAL In a signal handler (No change)
LED_ASSERTION An assertion failed (No change)
LED_PANIC The system has crashed Blinking OFF/RED
LED_IDLE MCU is is sleep mode (Not used)
Thus if the LED is GREEN then NuttX has successfully booted and is,
apparently, running normally. If the LED is flashing OFF/RED at
approximately 2Hz, then a fatal error has been detected and the
system has halted.
Serial Console
==============
By default, all configurations use UART0 which connects to the USB VCOM
on the DEBUG port on the TM4C123 ICDI interface:
UART0 RX - PA.0
UART0 TX - PA.1
However, if you use an external RS232 driver, then other options are
available. If your serial terminal loses connection with the USB serial
port each time you power cycle the board, the VCOM option can be very
painful.
UART0 TTL level signals are also available at J3 (also at J1):
DEBUG_TX - J3, pin 13. Labelled PA1
DEBUG_RX - J3, pin 15. Labelled PA0
Remove the jumper between pins 13-14 and 15-16 to disconnect UART0 from
the TM4C123 ICDI chip; Connect your external RS-232 driver at pins 13
and 16. 5v, 3.3v, AND GND are arvailable nearby at J10.
Networking Support
==================
Networking support via the can be added to NSH by selecting the following
configuration options.
Selecting the EMAC peripheral
-----------------------------
System Type -> SAM34 Peripheral Support
CONFIG_TIVA_ETHERNET=y : Enable the EMAC peripheral
System Type -> EMAC device driver options
CONFIG_TIVA_EMAC_NRXDESC=8 : Set aside some RX and TX descriptors/buffers
CONFIG_TIVA_EMAC_NTXDESC=4
CONFIG_TIVA_AUTONEG=y : Use autonegotiation
CONFIG_TIVA_PHY_INTERNAL=y : Use the internal PHY
CONFIG_TIVA_BOARDMAC=y : Use the MAC address in the FLASH USER0/1 registers
Networking Support
CONFIG_NET=y : Enable Neworking
CONFIG_NET_ETHERNET=y : Support Ethernet data link
CONFIG_NET_SOCKOPTS=y : Enable socket operations
CONFIG_NET_ETH_PKTSIZE=590 : Maximum packet size 1518 is more standard
CONFIG_NET_ARP=y : Enable ARP
CONFIG_NET_ARPTAB_SIZE=16 : ARP table size
CONFIG_NET_ARP_IPIN=y : Enable ARP address harvesting
CONFIG_NET_ARP_SEND=y : Send ARP request before sending data
CONFIG_NET_TCP=y : Enable TCP/IP networking
CONFIG_NET_TCP_READAHEAD=y : Support TCP read-ahead
CONFIG_NET_TCP_WRITE_BUFFERS=y : Support TCP write-buffering
CONFIG_NET_TCPBACKLOG=y : Support TCP/IP backlog
CONFIG_NET_MAX_LISTENPORTS=20 :
CONFIG_NET_TCP_READAHEAD_BUFSIZE=536 Read-ahead buffer size
CONFIG_NET_UDP=y : Enable UDP networking
CONFIG_NET_BROADCAST=y : Needed for DNS name resolution
CONFIG_NET_ICMP=y : Enable ICMP networking
CONFIG_NET_ICMP_SOCKET=y : Needed for NSH ping command
: Defaults should be okay for other options
f Application Configuration -> Network Utilities
CONFIG_NETDB_DNSCLIENT=y : Enable host address resolution
CONFIG_NETUTILS_TELNETD=y : Enable the Telnet daemon
CONFIG_NETUTILS_TFTPC=y : Enable TFTP data file transfers for get and put commands
CONFIG_NETUTILS_NETLIB=y : Network library support is needed
CONFIG_NETUTILS_WEBCLIENT=y : Needed for wget support
: Defaults should be okay for other options
Application Configuration -> NSH Library
CONFIG_NSH_TELNET=y : Enable NSH session via Telnet
CONFIG_NSH_IPADDR=0x0a000002 : Select a fixed IP address
CONFIG_NSH_DRIPADDR=0x0a000001 : IP address of gateway/host PC
CONFIG_NSH_NETMASK=0xffffff00 : Netmask
CONFIG_NSH_NOMAC=y : Need to make up a bogus MAC address
: Defaults should be okay for other options
You can also enable enable the DHCPC client for networks that use
dynamically assigned address:
Application Configuration -> Network Utilities
CONFIG_NETUTILS_DHCPC=y : Enables the DHCP client
Networking Support
CONFIG_NET_UDP=y : Depends on broadcast UDP
Application Configuration -> NSH Library
CONFIG_NET_BROADCAST=y
CONFIG_NSH_DHCPC=y : Tells NSH to use DHCPC, not
: the fixed addresses
Using the network with NSH
--------------------------
So what can you do with this networking support? First you see that
NSH has several new network related commands:
ifconfig, ifdown, ifup: Commands to help manage your network
get and put: TFTP file transfers
wget: HTML file transfers
ping: Check for access to peers on the network
Telnet console: You can access the NSH remotely via telnet.
You can also enable other add on features like full FTP or a Web
Server or XML RPC and others. There are also other features that
you can enable like DHCP client (or server) or network name
resolution.
By default, the IP address of the DK-TM4C129X will be 10.0.0.2 and
it will assume that your host is the gateway and has the IP address
10.0.0.1.
nsh> ifconfig
eth0 HWaddr 00:e0:de:ad:be:ef at UP
IPaddr:10.0.0.2 DRaddr:10.0.0.1 Mask:255.255.255.0
You can use ping to test for connectivity to the host (Careful,
Window firewalls usually block ping-related ICMP traffic). On the
target side, you can:
nsh> ping 10.0.0.1
PING 10.0.0.1 56 bytes of data
56 bytes from 10.0.0.1: icmp_seq=1 time=0 ms
56 bytes from 10.0.0.1: icmp_seq=2 time=0 ms
56 bytes from 10.0.0.1: icmp_seq=3 time=0 ms
56 bytes from 10.0.0.1: icmp_seq=4 time=0 ms
56 bytes from 10.0.0.1: icmp_seq=5 time=0 ms
56 bytes from 10.0.0.1: icmp_seq=6 time=0 ms
56 bytes from 10.0.0.1: icmp_seq=7 time=0 ms
56 bytes from 10.0.0.1: icmp_seq=8 time=0 ms
56 bytes from 10.0.0.1: icmp_seq=9 time=0 ms
56 bytes from 10.0.0.1: icmp_seq=10 time=0 ms
10 packets transmitted, 10 received, 0% packet loss, time 10100 ms
NOTE: In this configuration is is normal to have packet loss > 0%
the first time you ping due to the default handling of the ARP
table.
On the host side, you should also be able to ping the DK-TM4C129X:
$ ping 10.0.0.2
You can also log into the NSH from the host PC like this:
$ telnet 10.0.0.2
Trying 10.0.0.2...
Connected to 10.0.0.2.
Escape character is '^]'.
sh_telnetmain: Session [3] Started
NuttShell (NSH) NuttX-6.31
nsh> help
help usage: help [-v] [<cmd>]
[ echo ifconfig mkdir mw sleep
? exec ifdown mkfatfs ping test
cat exit ifup mkfifo ps umount
cp free kill mkrd put usleep
cmp get losetup mh rm wget
dd help ls mount rmdir xd
df hexdump mb mv sh
Builtin Apps:
nsh>
NOTE: If you enable this networking as described above, you will
experience a delay on booting NSH. That is because the start-up logic
waits for the network connection to be established before starting
NuttX. In a real application, you would probably want to do the
network bringup on a separate thread so that access to the NSH prompt
is not delayed.
This delay will be especially long if the board is not connected to
a network. On the order of minutes! You will probably think that
NuttX has crashed! And then, when it finally does come up after
numerous timeouts and retries, the network will not be available --
even if the network cable is plugged in later.
The long delays can be eliminated by using a separate the network
initialization thread discussed below. Recovering after the network
becomes available requires the network monitor feature, also discussed
below.
Network Initialization Thread
-----------------------------
There is a configuration option enabled by CONFIG_NSH_NETINIT_THREAD
that will do the NSH network bring-up asynchronously in parallel on
a separate thread. This eliminates the (visible) networking delay
altogether. This current implementation, however, has some limitations:
- If no network is connected, the network bring-up will fail and
the network initialization thread will simply exit. There are no
retries and no mechanism to know if the network initialization was
successful (it could perform a network Ioctl to see if the link is
up and it now, keep trying, but it does not do that now).
- Furthermore, there is currently no support for detecting loss of
network connection and recovery of the connection (similarly, this
thread could poll periodically for network status, but does not).
Both of these shortcomings could be eliminated by enabling the network
monitor:
Network Monitor
---------------
By default the network initialization thread will bring-up the network
then exit, freeing all of the resources that it required. This is a
good behavior for systems with limited memory.
If the CONFIG_NSH_NETINIT_MONITOR option is selected, however, then the
network initialization thread will persist forever; it will monitor the
network status. In the event that the network goes down (for example, if
a cable is removed), then the thread will monitor the link status and
attempt to bring the network back up. In this case the resources
required for network initialization are never released.
Pre-requisites:
- CONFIG_NSH_NETINIT_THREAD as described above.
- CONFIG_TIVA_PHY_INTERRUPTS=y. The TM4C129X EMAC block supports PHY
interrupts. This is true whether the TM4C internal PHY is used or
if an external PHY is used. If this option is selected, then support
for the PHY interrupt will be built in and the following additional
settings will be automatically selected:
CONFIG_NETDEV_PHY_IOCTL. Enable PHY IOCTL commands in the Ethernet
device driver. Special IOCTL commands must be provided by the Ethernet
driver to support certain PHY operations that will be needed for link
management. There operations are not complex and are implemented for
the Atmel SAMA5 family.
CONFIG_ARCH_PHY_INTERRUPT. This is not a user selectable option.
Rather, it is set when you select a board that supports PHY
interrupts. In most architectures, the PHY interrupt is not
associated with the Ethernet driver at all; the Tiva architecture is
an exception. For most other architectures, the PHY interrupt is
provided via some board-specific GPIO. In any event, the board-
specific logic must provide support for the PHY interrupt. To do
this, the board logic must do two things: (1) It must provide the
function arch_phy_irq() as described and prototyped in the
nuttx/include/nuttx/arch.h, and (2) it must select
CONFIG_ARCH_PHY_INTERRUPT in the board configuration file to
advertise that it supports arch_phy_irq().
And a few other things: UDP support is required (CONFIG_NET_UDP) and
signals must not be disabled (CONFIG_DISABLE_SIGNALS).
Given those prerequisites, the network monitor can be selected with these
additional settings.
System Type -> Tiva Ethernet Configuration
CONFIG_TIVA_PHY_INTERRUPTS=y : Enable PHY interrupt support
CONFIG_ARCH_PHY_INTERRUPT=y : (auto-selected)
CONFIG_NETDEV_PHY_IOCTL=y : (auto-selected)
Application Configuration -> NSH Library -> Networking Configuration
CONFIG_NSH_NETINIT_THREAD : Enable the network initialization thread
CONFIG_NSH_NETINIT_MONITOR=y : Enable the network monitor
CONFIG_NSH_NETINIT_RETRYMSEC=2000 : Configure the network monitor as you like
CONFIG_NSH_NETINIT_SIGNO=18
Timers
======
Tiva timers may be enabled in 32-bit periodic mode using these settings.
This settings enables the "upper half" timer driver:
Devices Drivers -> Timer Support
CONFIG_TIMER=y
These settings enable Tiva timer driver support
System Type -> Tiva/Stellaris Peripheral Support
CONFIG_TIVA_TIMER1=y : For timer 1
System Type -> Tiva Timer Configuration (using Timer 1)
CONFIG_TIVA_TIMER_32BIT=y
CONFIG_TIVA_TIMER32_PERIODIC=y
These setting enable board-specific logic to initialize the timer logic
(using Timer 1):
Board Selection -> Timer driver selection
CONFIG_DK_TM4C129X_TIMER1=y
CONFIG_DK_TM4C129X_TIMER_DEVNAME="/dev/timer0"
CONFIG_DK_TM4C129X_TIMER_TIMEOUT=10000
There is a simple example at apps/examples/timer that can be used to
exercise the timers. The following configuration options can be
selected to enable that example:
Application Configure -> Examples -> Timer Example
CONFIG_EXAMPLES_TIMER=y
CONFIG_EXAMPLES_TIMER_DEVNAME="/dev/timer0"
CONFIG_EXAMPLES_TIMER_DELAY=100000
CONFIG_EXAMPLES_TIMER_NSAMPLES=20
Temperature Sensor
==================
TMP-1000 Temperature Sensor Driver
----------------------------------
Support for the on-board TMP-100 temperature sensor is available. This
uses the driver for the compatible LM-75 part. To set up the temperature
sensor, add the following to the NuttX configuration file:
System Type -> Tiva/Stellaris Peripheral Selection
CONFIG_TIVA_I2C6=y
Drivers -> I2C Support
CONFIG_I2C=y
Drivers -> Sensors
CONFIG_SENSORS_LM75=y
CONFIG_LM75_I2C=y
Applications -> NSH Library
CONFIG_NSH_ARCHINIT=y
Then you can implement logic like the following to use the temperature sensor:
#include <nuttx/sensors/lm75.h>
#include <arch/board/board.h>
ret = tiva_tmp100_initialize("/dev/temp"); /* Register the temperature sensor */
fd = open("/dev/temp", O_RDONLY); /* Open the temperature sensor device */
ret = ioctl(fd, SNIOC_FAHRENHEIT, 0); /* Select Fahrenheit */
bytesread = read(fd, buffer, 8*sizeof(b16_t)); /* Read (8) temperature samples */
More complex temperature sensor operations are also available. See the IOCTL
commands enumerated in include/nuttx/sensors/lm75.h. Also read the descriptions
of the tiva_tmp100_initialize() and tiva_tmp100_attach() interfaces in the
arch/board/board.h file (sames as configs/dk-tm4c129x/include/board.h).
NSH Command Line Application
----------------------------
There is a tiny NSH command line application at examples/system/lm75 that
will read the current temperature from an LM75 compatible temperature sensor
and print the temperature on stdout in either units of degrees Fahrenheit or
Centigrade. This tiny command line application is enabled with the following
configuration options:
Library
CONFIG_LIBM=y
CONFIG_LIBC_FLOATINGPOINT=y
Applications -> NSH Library
CONFIG_NSH_ARCHINIT=y
Applications -> System Add-Ons
CONFIG_SYSTEM_LM75=y
CONFIG_SYSTEM_LM75_DEVNAME="/dev/temp"
CONFIG_SYSTEM_LM75_FAHRENHEIT=y (or CENTIGRADE)
CONFIG_SYSTEM_LM75_STACKSIZE=1024
CONFIG_SYSTEM_LM75_PRIORITY=100
DK-TM4129X Configuration Options
================================
CONFIG_ARCH - Identifies the arch/ subdirectory. This should
be set to:
CONFIG_ARCH=arm
CONFIG_ARCH_family - For use in C code:
CONFIG_ARCH_ARM=y
CONFIG_ARCH_architecture - For use in C code:
CONFIG_ARCH_CORTEXM4=y
CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
CONFIG_ARCH_CHIP="tiva"
CONFIG_ARCH_CHIP_name - For use in C code to identify the exact
chip:
CONFIG_ARCH_CHIP_TM4C129XNC
CONFIG_ARCH_BOARD - Identifies the configs subdirectory and
hence, the board that supports the particular chip or SoC.
CONFIG_ARCH_BOARD=dk-tm4c129x (for the DK-TM4129X)
CONFIG_ARCH_BOARD_name - For use in C code
CONFIG_ARCH_BOARD_DK_TM4C129X
CONFIG_ARCH_LOOPSPERMSEC - Must be calibrated for correct operation
of delay loops
CONFIG_ENDIAN_BIG - define if big endian (default is little
endian)
CONFIG_RAM_SIZE - Describes the installed DRAM (SRAM in this case):
CONFIG_RAM_SIZE=0x00008000 (32Kb)
CONFIG_RAM_START - The start address of installed DRAM
CONFIG_RAM_START=0x20000000
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to boards that
have LEDs
CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
stack. If defined, this symbol is the size of the interrupt
stack in bytes. If not defined, the user task stacks will be
used during interrupt handling.
CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.
CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
cause a 100 second delay during boot-up. This 100 second delay
serves no purpose other than it allows you to calibratre
CONFIG_ARCH_LOOPSPERMSEC. You simply use a stop watch to measure
the 100 second delay then adjust CONFIG_ARCH_LOOPSPERMSEC until
the delay actually is 100 seconds.
There are configurations for disabling support for interrupts GPIO ports.
Only GPIOP and GPIOQ pins can be used as interrupting sources on the
TM4C129X. Additional interrupt support can be disabled if desired to
reduce memory footprint.
CONFIG_TIVA_GPIOP_IRQS=y
CONFIG_TIVA_GPIOQ_IRQS=y
TM4C129X specific device driver settings
CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the
console and ttys0 (default is the UART0).
CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received.
This specific the size of the receive buffer
CONFIG_UARTn_TXBUFSIZE - Characters are buffered before
being sent. This specific the size of the transmit buffer
CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be
CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8.
CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
CONFIG_UARTn_2STOP - Two stop bits
CONFIG_TIVA_SSI0 - Select to enable support for SSI0
CONFIG_TIVA_SSI1 - Select to enable support for SSI1
CONFIG_SSI_POLLWAIT - Select to disable interrupt driven SSI support.
Poll-waiting is recommended if the interrupt rate would be to
high in the interrupt driven case.
CONFIG_SSI_TXLIMIT - Write this many words to the Tx FIFO before
emptying the Rx FIFO. If the SPI frequency is high and this
value is large, then larger values of this setting may cause
Rx FIFO overrun errors. Default: half of the Tx FIFO size (4).
CONFIG_TIVA_ETHERNET - This must be set (along with CONFIG_NET)
to build the Tiva Ethernet driver
CONFIG_TIVA_ETHLEDS - Enable to use Ethernet LEDs on the board.
CONFIG_TIVA_BOARDMAC - If the board-specific logic can provide
a MAC address (via tiva_ethernetmac()), then this should be selected.
CONFIG_TIVA_ETHHDUPLEX - Set to force half duplex operation
CONFIG_TIVA_ETHNOAUTOCRC - Set to suppress auto-CRC generation
CONFIG_TIVA_ETHNOPAD - Set to suppress Tx padding
CONFIG_TIVA_MULTICAST - Set to enable multicast frames
CONFIG_TIVA_PROMISCUOUS - Set to enable promiscuous mode
CONFIG_TIVA_BADCRC - Set to enable bad CRC rejection.
CONFIG_TIVA_DUMPPACKET - Dump each packet received/sent to the console.
Configurations
==============
Each DK-TM4C129X configuration is maintained in a
sub-directory and can be selected as follow:
tools/configure.sh dk-tm4c129x/<subdir>
Where <subdir> is one of the following:
nsh:
---
Configures the NuttShell (nsh) located at apps/examples/nsh. The
configuration enables the serial VCOM interfaces on UART0. Support for
builtin applications is enabled, but in the base configuration no
builtin applications are selected.
NOTES:
1. This configuration uses the mconf-based configuration tool. To
change this configuration using that tool, you should:
a. Build and install the kconfig-mconf tool. See nuttx/README.txt
see additional README.txt files in the NuttX tools repository.
b. Execute 'make menuconfig' in nuttx/ in order to start the
reconfiguration process.
2. By default, this configuration uses the CodeSourcery toolchain
for Windows and builds under Cygwin (or probably MSYS). That
can easily be reconfigured, of course.
CONFIG_HOST_WINDOWS=y : Windows
:CONFIG_WINDOWS_CYGWIN=y : Cygwin under Windows
CONFIG_ARMV7M_TOOLCHAIN_CODESOURCERYW=y : CodeSourcry fro Windows (arm-none-eabi-gcc)
CONFIG_RAW_BINARY=y : Output formats: ELF and raw binary
3. Default stack sizes are large and should really be tuned to reduce
the RAM footprint:
CONFIG_SCHED_HPWORKSTACKSIZE=2048
CONFIG_IDLETHREAD_STACKSIZE=1024
CONFIG_USERMAIN_STACKSIZE=2048
CONFIG_PTHREAD_STACK_DEFAULT=2048
CONFIG_POSIX_SPAWN_PROXY_STACKSIZE=1024
CONFIG_TASK_SPAWN_DEFAULT_STACKSIZE=2048
CONFIG_BUILTIN_PROXY_STACKSIZE=1024
CONFIG_NSH_TELNETD_DAEMONSTACKSIZE=2048
CONFIG_NSH_TELNETD_CLIENTSTACKSIZE=2048
4. This configuration has the network enabled by default. See the
paragraph "Using the network with NSH" above).
Networking can be easily be disabled or reconfigured (See see the
network related configuration settings above in the section entitled
"Networking").
By default, this configuration assumes a 10.0.0.xx network. It
uses a fixed IP address of 10.0.0.2 and assumes that the host is
at 10.0.0.1 and that the host provides the default router. The
network mask is 255.255.255.0. These address can be changed by
modifying the settings in the configuration. DHCPC can be enabled
be modifying this default configuration (See the "Networking"
section above).
The network initialization thread is enabled in this example. NSH
will create a separate thread when it starts to initialize the
network. This eliminates start-up delays to bring the network. This
feature may be disabled by reverting the configuration described above
under "Network Initialization Thread"
The persistent network monitor thread is also available in this
configuration. The network monitor will monitor changes in the
link status and gracefully take the network down when the link is
lost (for example, if the cable is disconnected) and bring the
network back up when the link becomes available again (for example,
if the cable is reconnected). The paragraph "Network Monitor" above
for additional information.
5. I2C6 and support for the on-board TMP-100 temperature sensor are
enabled. Also enabled is the NSH 'temp' command that will show the
current temperature on the command line like:
nsh> temp
80.60 degrees Fahrenheit
[80.6 F in January. I love living in Costa Rica1]
The default units is degrees Fahrenheit, but that is easily
reconfigured. See the discussin above in the paragraph entitled
"Temperature Sensor".
ipv6:
----
This is another version of the NuttShell configuration. It is very
similar to the nsh configuration except that it has IPv6 enabled and
IPv4 disabled. Several network utilities that are not yet available
under IPv6 are disabled.
NOTES:
1. As of 2015-01-23, this configuration was identical to the nsh
configuration other than using IPv6. So all of the notes above
regarding the nsh configuration apply.
Telnet does work with IPv6 but is not enabled in this
configuration (but could be).
2. This configuration can be modified to that both IPv4 and IPv6
are support. Here is a summary of the additional configuration
settings requird to support both IPv4 and IPv6:
CONFIG_NET_IPv4=y
CONFIG_NET_ARP=y
CONFIG_NET_ARP_SEND=y (optional)
CONFIG_NET_ICMP=y
CONFIG_NET_ICMP_SOCKET=y
CONFIG_NETDB_DNSCLIENT=y
CONFIG_NETUTILS_TELNETD=y
CONFIG_NSH_IPADDR=0x0a000002
CONFIG_NSH_DRIPADDR=0x0a000001
CONFIG_NSH_NETMASK=0xffffff00
CONFIG_NSH_TELNET=y
Then from NSH, you have both ping and ping6 commands:
nsh> ping 10.0.0.1
nsh> ping6 fc00::1
And from the host you can do similar:
ping 10.0.0.2
ping6 fc00::2 (Linux)
ping -6 fc00::2 (Windows cmd)
and Telnet is now enabled and works from the host... but only using
IPv6 addressing:
telnet fc00::2
That is because the Telnet daemon will default to IPv6 and there is
no Telnet option to let you select which if both IPv4 and IPv6 are
enabled.
3. You can enable IPv6 autonomous address configuration with the
following changes to the configuration:
+ CONFIG_NET_ICMPv6_AUTOCONF=y
+ CONFIG_ICMPv6_AUTOCONF_DELAYMSEC=100
+ CONFIG_ICMPv6_AUTOCONF_MAXTRIES=5
- CONFIG_NSH_DRIPv6ADDR_1=0xfc00
- CONFIG_NSH_DRIPv6ADDR_2=0x0000
- CONFIG_NSH_DRIPv6ADDR_3=0x0000
- CONFIG_NSH_DRIPv6ADDR_4=0x0000
- CONFIG_NSH_DRIPv6ADDR_5=0x0000
- CONFIG_NSH_DRIPv6ADDR_6=0x0000
- CONFIG_NSH_DRIPv6ADDR_7=0x0000
- CONFIG_NSH_DRIPv6ADDR_8=0x0001
- CONFIG_NSH_IPv6ADDR_1=0xfc00
- CONFIG_NSH_IPv6ADDR_2=0x0000
- CONFIG_NSH_IPv6ADDR_3=0x0000
- CONFIG_NSH_IPv6ADDR_4=0x0000
- CONFIG_NSH_IPv6ADDR_5=0x0000
- CONFIG_NSH_IPv6ADDR_6=0x0000
- CONFIG_NSH_IPv6ADDR_7=0x0000
- CONFIG_NSH_IPv6ADDR_8=0x0002
- CONFIG_NSH_IPv6NETMASK_1=0xffff
- CONFIG_NSH_IPv6NETMASK_2=0xffff
- CONFIG_NSH_IPv6NETMASK_3=0xffff
- CONFIG_NSH_IPv6NETMASK_4=0xffff
- CONFIG_NSH_IPv6NETMASK_5=0xffff
- CONFIG_NSH_IPv6NETMASK_6=0xffff
- CONFIG_NSH_IPv6NETMASK_7=0xffff
- CONFIG_NSH_IPv6NETMASK_8=0xff80
Reference in New Issue View Git Blame Copy Permalink