76dd2b9d58
git-svn-id: svn://svn.code.sf.net/p/nuttx/code/trunk@3408 42af7a65-404d-4744-a932-0658087f49c3
819 lines
30 KiB
Plaintext
819 lines
30 KiB
Plaintext
############################################################################
|
|
# configs/ez80f910200zco/nettest/defconfig
|
|
#
|
|
# Copyright (C) 2008-2010 Gregory Nutt. All rights reserved.
|
|
# Author: Gregory Nutt <spudmonkey@racsa.co.cr>
|
|
#
|
|
# Redistribution and use in source and binary forms, with or without
|
|
# modification, are permitted provided that the following conditions
|
|
# are met:
|
|
#
|
|
# 1. Redistributions of source code must retain the above copyright
|
|
# notice, this list of conditions and the following disclaimer.
|
|
# 2. Redistributions in binary form must reproduce the above copyright
|
|
# notice, this list of conditions and the following disclaimer in
|
|
# the documentation and/or other materials provided with the
|
|
# distribution.
|
|
# 3. Neither the name NuttX nor the names of its contributors may be
|
|
# used to endorse or promote products derived from this software
|
|
# without specific prior written permission.
|
|
#
|
|
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
|
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
|
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
|
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
|
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
|
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
|
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
|
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
|
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
|
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
|
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
|
# POSSIBILITY OF SUCH DAMAGE.
|
|
#
|
|
############################################################################
|
|
#
|
|
# Architecture selection
|
|
#
|
|
# CONFIG_ARCH - identifies the arch subdirectory and, hence, the
|
|
# processor architecture.
|
|
# CONFIG_ARCH_name - for use in C code. This identifies the particular
|
|
# processor architecture or, more accurately, the specific directory under
|
|
# nuttx/arch to use (CONFIG_ARCH_Z80 specifies nuttx/arch/z80).
|
|
# CONFIG_ARCH_CHIP - Identifies the specific chip or SoC that implements the
|
|
# architecture.
|
|
# CONFIG_ARCH_CHIP_chip - for use in C code. This identifies the
|
|
# particular chip or SoC that the architecture is implemented
|
|
# in (CONFIG_ARCH_CHIP_EZ80)
|
|
# CONFIG_ARCH_CHIP_EZ80F91 - Identifies ez80 chip variant
|
|
# CONFIG_ARCH_CHIP_EZ80F92
|
|
# CONFIG_ARCH_CHIP_EZ80F93
|
|
# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence,
|
|
# the board that supports the particular chip or SoC.
|
|
# CONFIG_ARCH_BOARD_name - for use in C code
|
|
# CONFIG_ARCH_NOINTC - define if the architecture does not
|
|
# support an interrupt controller or otherwise cannot support
|
|
# APIs like up_enable_irq() and up_disable_irq().
|
|
# CONFIG_ARCH_IRQPRIO
|
|
# Define if the architecture suports prioritizaton of interrupts
|
|
# and the up_prioritize_irq() API.
|
|
# CONFIG_BOARD_LOOPSPERMSEC - for delay loops
|
|
# CONFIG_ENDIAN_BIG - Define for big endian (default is little endian)
|
|
# CONFIG_DRAM_SIZE - Describes the installed DRAM.
|
|
# CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.
|
|
# CONFIG_ARCH_BUTTONS - Provide button APIs. Unique to board architecture.
|
|
# CONFIG_ARCH_TIMERHOOK - Provide board-specific hooks into periodic timer logic.
|
|
#
|
|
CONFIG_ARCH=z80
|
|
CONFIG_ARCH_Z80=y
|
|
CONFIG_ARCH_CHIP=ez80
|
|
CONFIG_ARCH_CHIP_EZ80=y
|
|
CONFIG_ARCH_CHIP_EZ80F91=y
|
|
CONFIG_ARCH_CHIP_EZ80F92=n
|
|
CONFIG_ARCH_CHIP_EZ80F93=n
|
|
CONFIG_ARCH_BOARD=ez80f910200zco
|
|
CONFIG_ARCH_BOARD_EZ80F910200ZCO=y
|
|
CONFIG_ARCH_NOINTC=n
|
|
CONFIG_ARCH_IRQPRIO=n
|
|
CONFIG_BOARD_LOOPSPERMSEC=1250
|
|
CONFIG_ENDIAN_BIG=n
|
|
CONFIG_DRAM_SIZE=65536
|
|
CONFIG_ARCH_LEDS=y
|
|
CONFIG_ARCH_BUTTONS=n
|
|
CONFIG_ARCH_TIMERHOOK=y
|
|
CONFIG_ARCH_STACKDUMP=n
|
|
|
|
#
|
|
# eZ80 specific device driver settings
|
|
#
|
|
# CONFIG_UARTn_DISABLE - Disables all support for UARTn.
|
|
# CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the
|
|
# console and ttyS0 (default is the UART0).
|
|
# CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received.
|
|
# This specific the size of the receive buffer
|
|
# CONFIG_UARTn_TXBUFSIZE - Characters are buffered before
|
|
# being sent. This specific the size of the transmit buffer
|
|
# CONFIG_UARTn_BAUD - The configure BAUD of the UART.
|
|
# CONFIG_UARTn_BITS - The number of data bits (7 or 8)
|
|
# CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
|
|
# CONFIG_UARTn_2STOP - 0=1 stop bit; 1=Two stop bits
|
|
#
|
|
CONFIG_UART0_DISABLE=n
|
|
CONFIG_UART1_DISABLE=y
|
|
CONFIG_UART0_SERIAL_CONSOLE=y
|
|
CONFIG_UART1_SERIAL_CONSOLE=n
|
|
CONFIG_UART0_TXBUFSIZE=0
|
|
CONFIG_UART1_TXBUFSIZE=0
|
|
CONFIG_UART0_RXBUFSIZE=0
|
|
CONFIG_UART1_RXBUFSIZE=0
|
|
CONFIG_UART0_BAUD=57600
|
|
CONFIG_UART1_BAUD=57600
|
|
CONFIG_UART0_BITS=0
|
|
CONFIG_UART1_BITS=0
|
|
CONFIG_UART0_PARITY=0
|
|
CONFIG_UART1_PARITY=0
|
|
CONFIG_UART0_2STOP=0
|
|
CONFIG_UART1_2STOP=0
|
|
|
|
#
|
|
# ez80 EMAC
|
|
#
|
|
# CONFIG_EZ80_EMAC - Enables support for ez80 EMAC driver.
|
|
# CONFIG_EZ80_FIAD - Provides the MII address of the PHY device
|
|
# CONFIG_EZ80_PHYAM79C874 - Define for Am79c874 PHY
|
|
# CONFIG_EZ80_PHYCONFIG - 0:Autonegotiate, 1:100FD, 2:100HD, 3:10FD, 4:10HD
|
|
# CONFIG_EZ80_RAMADDR - Address of internal SRAM (default is 0xffc000)
|
|
# CONFIG_EZ80_PKTBUFSIZE, CONFIG_EZ80_NTXPKTBUFS, and CONFIG_EZ80_NRXPKTBUFS -
|
|
# The size of one packet buffer and the number of Rx and Tx packet
|
|
# buffers. This must add up to exactly 8192 bytes.
|
|
# CONFIG_EZ80_MDCDIV=1 - The value to use for the divider to derive
|
|
# the MII MDC clock from SLCK. Options are 1->4; 2->6; 3->8; 4->10;
|
|
# 5->14; 6->20; and 7->28
|
|
# CONFIG_EZ80_TXPOLLTIMERMS - Specifies how often the EMAC controller
|
|
# should poll for a Tx packet (milliseconds)
|
|
# CONFIG_ARCH_MCFILTER - Enalbes multicast MAC address filtering (not
|
|
# fully implemented
|
|
CONFIG_EZ80_EMAC=y
|
|
CONFIG_EZ80_FIAD=0x1f
|
|
CONFIG_EZ80_PHYAM79C874=y
|
|
CONFIG_EZ80_PHYCONFIG=1
|
|
CONFIG_EZ80_RAMADDR=0xf7c000
|
|
CONFIG_EZ80_PKTBUFSIZE=64
|
|
CONFIG_EZ80_NTXPKTBUFS=64
|
|
CONFIG_EZ80_NRXPKTBUFS=64
|
|
CONFIG_EZ80_PKTBUFSIZE=64
|
|
CONFIG_EZ80_MDCDIV=0
|
|
CONFIG_EZ80_TXPOLLTIMERMS=10
|
|
CONFIG_ARCH_MCFILTER=n
|
|
|
|
#
|
|
# General build options
|
|
#
|
|
# CONFIG_RRLOAD_BINARY - make the rrload binary format used with
|
|
# BSPs from www.ridgerun.com using the tools/mkimage.sh script
|
|
# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format
|
|
# used with many different loaders using the GNU objcopy program
|
|
# Should not be selected if you are not using the GNU toolchain.
|
|
# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format
|
|
# used with many different loaders using the GNU objcopy program
|
|
# Should not be selected if you are not using the GNU toolchain.
|
|
# CONFIG_RAW_BINARY - make a raw binary format file used with many
|
|
# different loaders using the GNU objcopy program. This option
|
|
# should not be selected if you are not using the GNU toolchain.
|
|
# CONFIG_HAVE_LIBM - toolchain supports libm.a
|
|
#
|
|
CONFIG_RRLOAD_BINARY=n
|
|
CONFIG_INTELHEX_BINARY=n
|
|
CONFIG_MOTOROLA_SREC=n
|
|
CONFIG_RAW_BINARY=n
|
|
CONFIG_HAVE_LIBM=n
|
|
|
|
#
|
|
# General OS setup
|
|
#
|
|
# CONFIG_APPS_DIR - Identifies the relative path to the directory
|
|
# that builds the application to link with NuttX. Default: ../apps
|
|
# CONFIG_DEBUG - enables built-in debug options
|
|
# CONFIG_DEBUG_VERBOSE - enables verbose debug output
|
|
# CONFIG_DEBUG_NET - enables debug of the network subsystem
|
|
# CONFIG_DEBUG_SYMBOLS - build without optimization and with
|
|
# debug symbols (needed for use with a debugger).
|
|
# CONFIG_MM_REGIONS - If the architecture includes multiple
|
|
# regions of memory to allocate from, this specifies the
|
|
# number of memory regions that the memory manager must
|
|
# handle and enables the API mm_addregion(start, end);
|
|
# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot
|
|
# time console output
|
|
# CONFIG_HAVE_GETPUTC - architecture supports low-level, boot
|
|
# time console input
|
|
# CONFIG_TICKS_PER_MSEC - The default system timer is 100Hz
|
|
# or TICKS_PER_MSEC=10. This setting may be defined to
|
|
# inform NuttX that the processor hardware is providing
|
|
# system timer interrupts at some interrupt interval other
|
|
# than 10 msec.
|
|
# CONFIG_RR_INTERVAL - The round robin timeslice will be set
|
|
# this number of milliseconds; Round robin scheduling can
|
|
# be disabled by setting this value to zero.
|
|
# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in
|
|
# scheduler to monitor system performance
|
|
# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a
|
|
# task name to save in the TCB. Useful if scheduler
|
|
# instrumentation is selected. Set to zero to disable.
|
|
# CONFIG_JULIAN_TIME - Enables Julian time conversions
|
|
# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY -
|
|
# Used to initialize the internal time logic.
|
|
# CONFIG_HAVE_LOWUARTINIT - Provides low-level UART initialization
|
|
# logic as up_lowuartinit (only needed if there is no
|
|
# serial driver).
|
|
# CONFIG_DEV_CONSOLE - Set if architecture-specific logic
|
|
# provides /dev/console. Enables stdout, stderr, stdin.
|
|
# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console
|
|
# driver (minimal, write-only support)
|
|
# CONFIG_MUTEX_TYPES: Set to enable support for recursive and
|
|
# errorcheck mutexes. Enables pthread_mutexattr_settype().
|
|
# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority
|
|
# inheritance on mutexes and semaphores.
|
|
# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority
|
|
# inheritance is enabled. It defines the maximum number of
|
|
# different threads (minus one) that can take counts on a
|
|
# semaphore with priority inheritance support. This may be
|
|
# set to zero if priority inheritance is disabled OR if you
|
|
# are only using semaphores as mutexes (only one holder) OR
|
|
# if no more than two threads participate using a counting
|
|
# semaphore.
|
|
# CONFIG_SEM_NNESTPRIO. If priority inheritance is enabled,
|
|
# then this setting is the maximum number of higher priority
|
|
# threads (minus 1) than can be waiting for another thread
|
|
# to release a count on a semaphore. This value may be set
|
|
# to zero if no more than one thread is expected to wait for
|
|
# a semaphore.
|
|
# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors
|
|
# by task_create() when a new task is started. If set, all
|
|
# files/drivers will appear to be closed in the new task.
|
|
# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first
|
|
# three file descriptors (stdin, stdout, stderr) by task_create()
|
|
# when a new task is started. If set, all files/drivers will
|
|
# appear to be closed in the new task except for stdin, stdout,
|
|
# and stderr.
|
|
# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket
|
|
# desciptors by task_create() when a new task is started. If
|
|
# set, all sockets will appear to be closed in the new task.
|
|
#
|
|
#CONFIG_APPS_DIR=
|
|
CONFIG_DEBUG=y
|
|
CONFIG_DEBUG_VERBOSE=n
|
|
CONFIG_DEBUG_SYMBOLS=n
|
|
CONFIG_DEBUG_NET=n
|
|
CONFIG_MM_REGIONS=1
|
|
CONFIG_ARCH_LOWPUTC=y
|
|
CONFIG_RR_INTERVAL=200
|
|
CONFIG_SCHED_INSTRUMENTATION=n
|
|
CONFIG_TASK_NAME_SIZE=0
|
|
CONFIG_START_YEAR=2009
|
|
CONFIG_START_MONTH=3
|
|
CONFIG_START_DAY=14
|
|
CONFIG_JULIAN_TIME=n
|
|
CONFIG_HAVE_LOWUARTINIT=y
|
|
CONFIG_DEV_CONSOLE=y
|
|
CONFIG_DEV_LOWCONSOLE=y
|
|
CONFIG_MUTEX_TYPES=n
|
|
CONFIG_PRIORITY_INHERITANCE=n
|
|
CONFIG_SEM_PREALLOCHOLDERS=0
|
|
CONFIG_SEM_NNESTPRIO=0
|
|
CONFIG_FDCLONE_DISABLE=n
|
|
CONFIG_FDCLONE_STDIO=n
|
|
CONFIG_SDCLONE_DISABLE=y
|
|
|
|
#
|
|
# The following can be used to disable categories of
|
|
# APIs supported by the OS. If the compiler supports
|
|
# weak functions, then it should not be necessary to
|
|
# disable functions unless you want to restrict usage
|
|
# of those APIs.
|
|
#
|
|
# There are certain dependency relationships in these
|
|
# features.
|
|
#
|
|
# o mq_notify logic depends on signals to awaken tasks
|
|
# waiting for queues to become full or empty.
|
|
# o pthread_condtimedwait() depends on signals to wake
|
|
# up waiting tasks.
|
|
#
|
|
CONFIG_DISABLE_CLOCK=n
|
|
CONFIG_DISABLE_POSIX_TIMERS=n
|
|
CONFIG_DISABLE_PTHREAD=y
|
|
CONFIG_DISABLE_SIGNALS=n
|
|
CONFIG_DISABLE_MQUEUE=y
|
|
CONFIG_DISABLE_MOUNTPOINT=y
|
|
CONFIG_DISABLE_ENVIRON=y
|
|
CONFIG_DISABLE_POLL=y
|
|
|
|
#
|
|
# Misc libc settings
|
|
#
|
|
# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a
|
|
# little smaller if we do not support fieldwidthes
|
|
#
|
|
CONFIG_NOPRINTF_FIELDWIDTH=n
|
|
|
|
#
|
|
# Allow for architecture optimized implementations
|
|
#
|
|
# The architecture can provide optimized versions of the
|
|
# following to improve sysem performance
|
|
#
|
|
CONFIG_ARCH_MEMCPY=n
|
|
CONFIG_ARCH_MEMCMP=n
|
|
CONFIG_ARCH_MEMMOVE=n
|
|
CONFIG_ARCH_MEMSET=n
|
|
CONFIG_ARCH_STRCMP=n
|
|
CONFIG_ARCH_STRCPY=n
|
|
CONFIG_ARCH_STRNCPY=n
|
|
CONFIG_ARCH_STRLEN=n
|
|
CONFIG_ARCH_STRNLEN=n
|
|
CONFIG_ARCH_BZERO=n
|
|
CONFIG_ARCH_KMALLOC=n
|
|
CONFIG_ARCH_KZMALLOC=n
|
|
CONFIG_ARCH_KFREE=n
|
|
|
|
#
|
|
# Sizes of configurable things (0 disables)
|
|
#
|
|
# CONFIG_MAX_TASKS - The maximum number of simultaneously
|
|
# active tasks. This value must be a power of two.
|
|
# CONFIG_MAX_TASK_ARGS - This controls the maximum number of
|
|
# of parameters that a task may receive (i.e., maxmum value
|
|
# of 'argc')
|
|
# CONFIG_NPTHREAD_KEYS - The number of items of thread-
|
|
# specific data that can be retained
|
|
# CONFIG_NFILE_DESCRIPTORS - The maximum number of file
|
|
# descriptors (one for each open)
|
|
# CONFIG_NFILE_STREAMS - The maximum number of streams that
|
|
# can be fopen'ed
|
|
# CONFIG_NAME_MAX - The maximum size of a file name.
|
|
# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate
|
|
# on fopen. (Only if CONFIG_NFILE_STREAMS > 0)
|
|
# CONFIG_NUNGET_CHARS - Number of characters that can be
|
|
# buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0)
|
|
# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message
|
|
# structures. The system manages a pool of preallocated
|
|
# message structures to minimize dynamic allocations
|
|
# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with
|
|
# a fixed payload size given by this settin (does not include
|
|
# other message structure overhead.
|
|
# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that
|
|
# can be passed to a watchdog handler
|
|
# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog
|
|
# structures. The system manages a pool of preallocated
|
|
# watchdog structures to minimize dynamic allocations
|
|
# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX
|
|
# timer structures. The system manages a pool of preallocated
|
|
# timer structures to minimize dynamic allocations. Set to
|
|
# zero for all dynamic allocations.
|
|
#
|
|
CONFIG_MAX_TASKS=8
|
|
CONFIG_MAX_TASK_ARGS=4
|
|
CONFIG_NPTHREAD_KEYS=0
|
|
CONFIG_NFILE_DESCRIPTORS=8
|
|
CONFIG_NFILE_STREAMS=8
|
|
CONFIG_NAME_MAX=32
|
|
CONFIG_STDIO_BUFFER_SIZE=0
|
|
CONFIG_NUNGET_CHARS=0
|
|
CONFIG_PREALLOC_MQ_MSGS=0
|
|
CONFIG_MQ_MAXMSGSIZE=0
|
|
CONFIG_MAX_WDOGPARMS=4
|
|
CONFIG_PREALLOC_WDOGS=8
|
|
CONFIG_PREALLOC_TIMERS=8
|
|
|
|
#
|
|
# Framebuffer driver options
|
|
CONFIG_FB_CMAP=n
|
|
CONFIG_FB_HWCURSOR=n
|
|
CONFIG_FB_HWCURSORIMAGE=n
|
|
#CONFIG_FB_HWCURSORSIZE
|
|
#CONFIG_FB_TRANSPARENCY
|
|
|
|
#
|
|
# Filesystem configuration
|
|
#
|
|
# CONFIG_FS_FAT - Enable FAT filesystem support
|
|
# CONFIG_FAT_SECTORSIZE - Max supported sector size
|
|
# CONFIG_FS_ROMFS - Enable ROMFS filesystem support
|
|
CONFIG_FS_FAT=n
|
|
CONFIG_FS_ROMFS=n
|
|
|
|
#
|
|
# SPI-based MMC/SD driver
|
|
#
|
|
# CONFIG_MMCSD_NSLOTS
|
|
# Number of MMC/SD slots supported by the driver
|
|
# CONFIG_MMCSD_READONLY
|
|
# Provide read-only access (default is read/write)
|
|
CONFIG_MMCSD_NSLOTS=1
|
|
CONFIG_MMCSD_READONLY=n
|
|
|
|
#
|
|
# TCP/IP and UDP support via uIP
|
|
# CONFIG_NET - Enable or disable all network features
|
|
# CONFIG_NET_IPv6 - Build in support for IPv6
|
|
# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread.
|
|
# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options
|
|
# CONFIG_NET_BUFSIZE - uIP buffer size
|
|
# CONFIG_NET_TCP - TCP support on or off
|
|
# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks)
|
|
# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers
|
|
# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero)
|
|
# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until
|
|
# accept() is called. The size of the backlog is selected when listen() is called.
|
|
# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks)
|
|
# CONFIG_NET_UDP - UDP support on or off
|
|
# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off
|
|
# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections
|
|
# CONFIG_NET_ICMP - ICMP ping response support on or off
|
|
# CONFIG_NET_ICMP_PING - ICMP ping request support on or off
|
|
# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address
|
|
# CONFIG_NET_STATISTICS - uIP statistics on or off
|
|
# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window
|
|
# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table
|
|
# CONFIG_NET_BROADCAST - Broadcast support
|
|
# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when looking for duplicates
|
|
#
|
|
CONFIG_NET=y
|
|
CONFIG_NET_IPv6=n
|
|
CONFIG_NSOCKET_DESCRIPTORS=8
|
|
CONFIG_NET_SOCKOPTS=y
|
|
CONFIG_NET_BUFSIZE=420
|
|
CONFIG_NET_TCP=y
|
|
CONFIG_NET_TCP_CONNS=8
|
|
CONFIG_NET_NTCP_READAHEAD_BUFFERS=8
|
|
CONFIG_NET_TCPBACKLOG=n
|
|
CONFIG_NET_MAX_LISTENPORTS=8
|
|
CONFIG_NET_UDP=n
|
|
CONFIG_NET_UDP_CHECKSUMS=y
|
|
#CONFIG_NET_UDP_CONNS=10
|
|
CONFIG_NET_ICMP=y
|
|
CONFIG_NET_ICMP_PING=n
|
|
#CONFIG_NET_PINGADDRCONF=0
|
|
CONFIG_NET_STATISTICS=n
|
|
#CONFIG_NET_RECEIVE_WINDOW=
|
|
#CONFIG_NET_ARPTAB_SIZE=8
|
|
CONFIG_NET_BROADCAST=n
|
|
#CONFIG_NET_FWCACHE_SIZE=2
|
|
|
|
#
|
|
# UIP Network Utilities
|
|
# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP
|
|
# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries
|
|
CONFIG_NET_DHCP_LIGHT=n
|
|
CONFIG_NET_RESOLV_ENTRIES=4
|
|
|
|
#
|
|
# USB Device Configuration
|
|
#
|
|
# CONFIG_USBDEV
|
|
# Enables USB device support
|
|
# CONFIG_USBDEV_ISOCHRONOUS
|
|
# Build in extra support for isochronous endpoints
|
|
# CONFIG_USBDEV_DUALSPEED
|
|
# Hardware handles high and full speed operation (USB 2.0)
|
|
# CONFIG_USBDEV_SELFPOWERED
|
|
# Will cause USB features to indicate that the device is
|
|
# self-powered
|
|
# CONFIG_USBDEV_MAXPOWER
|
|
# Maximum power consumption in mA
|
|
# CONFIG_USBDEV_TRACE
|
|
# Enables USB tracing for debug
|
|
# CONFIG_USBDEV_TRACE_NRECORDS
|
|
# Number of trace entries to remember
|
|
CONFIG_USBDEV=n
|
|
CONFIG_USBDEV_ISOCHRONOUS=n
|
|
CONFIG_USBDEV_DUALSPEED=n
|
|
CONFIG_USBDEV_SELFPOWERED=y
|
|
CONFIG_USBDEV_REMOTEWAKEUP=n
|
|
CONFIG_USBDEV_MAXPOWER=100
|
|
CONFIG_USBDEV_TRACE=n
|
|
CONFIG_USBDEV_TRACE_NRECORDS=128
|
|
|
|
#
|
|
# USB Serial Device Configuration
|
|
#
|
|
# CONFIG_USBSER
|
|
# Enable compilation of the USB serial driver
|
|
# CONFIG_USBSER_EPINTIN
|
|
# The logical 7-bit address of a hardware endpoint that supports
|
|
# interrupt IN operation
|
|
# CONFIG_USBSER_EPBULKOUT
|
|
# The logical 7-bit address of a hardware endpoint that supports
|
|
# bulk OUT operation
|
|
# CONFIG_USBSER_EPBULKIN
|
|
# The logical 7-bit address of a hardware endpoint that supports
|
|
# bulk IN operation
|
|
# CONFIG_USBSER_NWRREQS and CONFIG_USBSER_NRDREQS
|
|
# The number of write/read requests that can be in flight
|
|
# CONFIG_USBSER_VENDORID and CONFIG_USBSER_VENDORSTR
|
|
# The vendor ID code/string
|
|
# CONFIG_USBSER_PRODUCTID and CONFIG_USBSER_PRODUCTSTR
|
|
# The product ID code/string
|
|
# CONFIG_USBSER_RXBUFSIZE and CONFIG_USBSER_TXBUFSIZE
|
|
# Size of the serial receive/transmit buffers
|
|
CONFIG_USBSER=n
|
|
CONFIG_USBSER_EPINTIN=1
|
|
CONFIG_USBSER_EPBULKOUT=2
|
|
CONFIG_USBSER_EPBULKIN=5
|
|
CONFIG_USBSER_NWRREQS=4
|
|
CONFIG_USBSER_NRDREQS=4
|
|
CONFIG_USBSER_VENDORID=0x067b
|
|
CONFIG_USBSER_PRODUCTID=0x2303
|
|
CONFIG_USBSER_VENDORSTR="Nuttx"
|
|
CONFIG_USBSER_PRODUCTSTR="USBdev Serial"
|
|
CONFIG_USBSER_RXBUFSIZE=512
|
|
CONFIG_USBSER_TXBUFSIZE=512
|
|
|
|
#
|
|
# USB Storage Device Configuration
|
|
#
|
|
# CONFIG_USBSTRG
|
|
# Enable compilation of the USB storage driver
|
|
# CONFIG_USBSTRG_EP0MAXPACKET
|
|
# Max packet size for endpoint 0
|
|
# CONFIG_USBSTRG_EPBULKOUT and CONFIG_USBSTRG_EPBULKIN
|
|
# The logical 7-bit address of a hardware endpoints that support
|
|
# bulk OUT and IN operations
|
|
# CONFIG_USBSTRG_NWRREQS and CONFIG_USBSTRG_NRDREQS
|
|
# The number of write/read requests that can be in flight
|
|
# CONFIG_USBSTRG_BULKINREQLEN and CONFIG_USBSTRG_BULKOUTREQLEN
|
|
# The size of the buffer in each write/read request. This
|
|
# value needs to be at least as large as the endpoint
|
|
# maxpacket and ideally as large as a block device sector.
|
|
# CONFIG_USBSTRG_VENDORID and CONFIG_USBSTRG_VENDORSTR
|
|
# The vendor ID code/string
|
|
# CONFIG_USBSTRG_PRODUCTID and CONFIG_USBSTRG_PRODUCTSTR
|
|
# The product ID code/string
|
|
# CONFIG_USBSTRG_REMOVABLE
|
|
# Select if the media is removable
|
|
CONFIG_USBSTRG=n
|
|
CONFIG_USBSTRG_EP0MAXPACKET=64
|
|
CONFIG_USBSTRG_EPBULKOUT=2
|
|
CONFIG_USBSTRG_EPBULKIN=5
|
|
CONFIG_USBSTRG_NRDREQS=2
|
|
CONFIG_USBSTRG_NWRREQS=2
|
|
CONFIG_USBSTRG_BULKINREQLEN=256
|
|
CONFIG_USBSTRG_BULKOUTREQLEN=256
|
|
CONFIG_USBSTRG_VENDORID=0x584e
|
|
CONFIG_USBSTRG_VENDORSTR="NuttX"
|
|
CONFIG_USBSTRG_PRODUCTID=0x5342
|
|
CONFIG_USBSTRG_PRODUCTSTR="USBdev Storage"
|
|
CONFIG_USBSTRG_VERSIONNO=0x0399
|
|
CONFIG_USBSTRG_REMOVABLE=y
|
|
|
|
#
|
|
# CONFIG_NX
|
|
# Enables overall support for graphics library and NX
|
|
# CONFIG_NX_MULTIUSER
|
|
# Configures NX in multi-user mode
|
|
# CONFIG_NX_NPLANES
|
|
# Some YUV color formats requires support for multiple planes,
|
|
# one for each color component. Unless you have such special
|
|
# hardware, this value should be undefined or set to 1
|
|
# CONFIG_NX_DISABLE_1BPP, CONFIG_NX_DISABLE_2BPP,
|
|
# CONFIG_NX_DISABLE_4BPP, CONFIG_NX_DISABLE_8BPP,
|
|
# CONFIG_NX_DISABLE_16BPP, CONFIG_NX_DISABLE_24BPP, and
|
|
# CONFIG_NX_DISABLE_32BPP
|
|
# NX supports a variety of pixel depths. You can save some
|
|
# memory by disabling support for unused color depths.
|
|
# CONFIG_NX_PACKEDMSFIRST
|
|
# If a pixel depth of less than 8-bits is used, then NX needs
|
|
# to know if the pixels pack from the MS to LS or from LS to MS
|
|
# CONFIG_NX_MOUSE
|
|
# Build in support for mouse input
|
|
# CONFIG_NX_KBD
|
|
# Build in support of keypad/keyboard input
|
|
# CONFIG_NXTK_BORDERWIDTH
|
|
# Specifies with with of the border (in pixels) used with
|
|
# framed windows. The default is 4.
|
|
# CONFIG_NXTK_BORDERCOLOR1 and CONFIG_NXTK_BORDERCOLOR2
|
|
# Specify the colors of the border used with framed windows.
|
|
# CONFIG_NXTK_BORDERCOLOR2 is the shadow side color and so
|
|
# is normally darker. The default is medium and dark grey,
|
|
# respectively
|
|
# CONFIG_NXTK_AUTORAISE
|
|
# If set, a window will be raised to the top if the mouse position
|
|
# is over a visible portion of the window. Default: A mouse
|
|
# button must be clicked over a visible portion of the window.
|
|
# CONFIG_NXFONTS_CHARBITS
|
|
# The number of bits in the character set. Current options are
|
|
# only 7 and 8. The default is 7.
|
|
# CONFIG_NXFONT_SANS
|
|
# At present, there is only one font. But if there were were more,
|
|
# then this option would select the sans serif font.
|
|
#
|
|
# NX Multi-user only options:
|
|
#
|
|
# CONFIG_NX_BLOCKING
|
|
# Open the client message queues in blocking mode. In this case,
|
|
# nx_eventhandler() will not return until a message is received and processed.
|
|
# CONFIG_NX_MXSERVERMSGS and CONFIG_NX_MXCLIENTMSGS
|
|
# Specifies the maximum number of messages that can fit in
|
|
# the message queues. No additional resources are allocated, but
|
|
# this can be set to prevent flooding of the client or server with
|
|
# too many messages (CONFIG_PREALLOC_MQ_MSGS controls how many
|
|
# messages are pre-allocated).
|
|
#
|
|
CONFIG_NX=n
|
|
CONFIG_NX_MULTIUSER=n
|
|
CONFIG_NX_NPLANES=1
|
|
CONFIG_NX_DISABLE_1BPP=y
|
|
CONFIG_NX_DISABLE_2BPP=y
|
|
CONFIG_NX_DISABLE_4BPP=y
|
|
CONFIG_NX_DISABLE_8BPP=n
|
|
CONFIG_NX_DISABLE_16BPP=y
|
|
CONFIG_NX_DISABLE_24BPP=y
|
|
CONFIG_NX_DISABLE_32BPP=y
|
|
CONFIG_NX_PACKEDMSFIRST=n
|
|
CONFIG_NX_MOUSE=y
|
|
CONFIG_NX_KBD=y
|
|
#CONFIG_NXTK_BORDERWIDTH=4
|
|
#CONFIG_NXTK_BORDERCOLOR1
|
|
#CONFIG_NXTK_BORDERCOLOR2
|
|
CONFIG_NXTK_AUTORAISE=n
|
|
CONFIG_NXFONT_SANS=y
|
|
CONFIG_NXFONTS_CHARBITS=7
|
|
CONFIG_NX_BLOCKING=y
|
|
CONFIG_NX_MXSERVERMSGS=32
|
|
CONFIG_NX_MXCLIENTMSGS=16
|
|
|
|
#
|
|
# Settings for examples/poll
|
|
CONFIG_EXAMPLE_POLL_NOMAC=y
|
|
CONFIG_EXAMPLE_POLL_IPADDR=(10L<<24|0L<<16|0L<<8|2L)
|
|
CONFIG_EXAMPLE_POLL_DRIPADDR=(10L<<24|0L<<16|0L<<8|1L)
|
|
CONFIG_EXAMPLE_POLL_NETMASK=(255L<<24|255L<<16|255L<<8|0L)
|
|
|
|
#
|
|
# Settings for examples/uip
|
|
CONFIG_EXAMPLE_UIP_IPADDR=(10L<<24|0L<<16|0L<<8|2L)
|
|
CONFIG_EXAMPLE_UIP_DRIPADDR=(10L<<24|0L<<16|0L<<8|1L)
|
|
CONFIG_EXAMPLE_UIP_NETMASK=(255L<<24|255L<<16|255L<<8|0L)
|
|
CONFIG_EXAMPLE_UIP_DHCPC=n
|
|
|
|
#
|
|
# Settings for examples/nettest
|
|
# CONFIG_EXAMPLE_NETTEST_SERVER - The target board can act
|
|
# as either the client side or server side of the test
|
|
# CONFIG_EXAMPLE_NETTEST_PERFORMANCE - If set, then the
|
|
# client side simply receives messages forever, allowing
|
|
# measurement of throughput
|
|
# CONFIG_EXAMPLE_NETTEST_NOMAC - Set if the hardware has
|
|
# no MAC address; one will be assigned
|
|
# CONFIG_EXAMPLE_NETTEST_IPADDR - Target board IP address
|
|
# CONFIG_EXAMPLE_NETTEST_DRIPADDR - Default router address
|
|
# CONFIG_EXAMPLE_NETTEST_NETMASK - Network mask
|
|
# CONFIG_EXAMPLE_NETTEST_CLIENTIP - IP address of the
|
|
# client side of the test (may be target or host)
|
|
CONFIG_EXAMPLE_NETTEST_SERVER=n
|
|
CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n
|
|
CONFIG_EXAMPLE_NETTEST_NOMAC=y
|
|
CONFIG_EXAMPLE_NETTEST_IPADDR=(10L<<24|0L<<16|0L<<8|2L)
|
|
CONFIG_EXAMPLE_NETTEST_DRIPADDR=(10L<<24|0L<<16|0L<<8|1L)
|
|
CONFIG_EXAMPLE_NETTEST_NETMASK=(255L<<24|255L<<16|255L<<8|0L)
|
|
CONFIG_EXAMPLE_NETTEST_CLIENTIP=(10L<<24|0L<<16|0L<<8|1L)
|
|
|
|
#
|
|
# Settings for examples/ostest
|
|
CONFIG_EXAMPLES_OSTEST_LOOPS=1
|
|
CONFIG_EXAMPLES_OSTEST_STACKSIZE=2048
|
|
CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3
|
|
|
|
#
|
|
# Settings for apps/nshlib
|
|
#
|
|
# CONFIG_NSH_FILEIOSIZE - Size of a static I/O buffer
|
|
# CONFIG_NSH_STRERROR - Use strerror(errno)
|
|
# CONFIG_NSH_LINELEN - Maximum length of one command line
|
|
# CONFIG_NSH_STACKSIZE - Stack size to use for new threads.
|
|
# CONFIG_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi
|
|
# CONFIG_NSH_DISABLESCRIPT - Disable scripting support
|
|
# CONFIG_NSH_DISABLEBG - Disable background commands
|
|
# CONFIG_NSH_ROMFSETC - Use startup script in /etc
|
|
# CONFIG_NSH_CONSOLE - Use serial console front end
|
|
# CONFIG_NSH_TELNET - Use telnetd console front end
|
|
#
|
|
# If CONFIG_NSH_TELNET is selected:
|
|
# CONFIG_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size
|
|
# CONFIG_NSH_DHCPC - Obtain address using DHCP
|
|
# CONFIG_NSH_IPADDR - Provides static IP address
|
|
# CONFIG_NSH_DRIPADDR - Provides static router IP address
|
|
# CONFIG_NSH_NETMASK - Provides static network mask
|
|
# CONFIG_NSH_NOMAC - Use a bogus MAC address
|
|
#
|
|
# If CONFIG_NSH_ROMFSETC is selected:
|
|
# CONFIG_NSH_ROMFSMOUNTPT - ROMFS mountpoint
|
|
# CONFIG_NSH_INITSCRIPT - Relative path to init script
|
|
# CONFIG_NSH_ROMFSDEVNO - ROMFS RAM device minor
|
|
# CONFIG_NSH_ROMFSSECTSIZE - ROMF sector size
|
|
# CONFIG_NSH_FATDEVNO - FAT FS RAM device minor
|
|
# CONFIG_NSH_FATSECTSIZE - FAT FS sector size
|
|
# CONFIG_NSH_FATNSECTORS - FAT FS number of sectors
|
|
# CONFIG_NSH_FATMOUNTPT - FAT FS mountpoint
|
|
CONFIG_NSH_FILEIOSIZE=512
|
|
CONFIG_NSH_STRERROR=n
|
|
CONFIG_NSH_LINELEN=64
|
|
CONFIG_NSH_STACKSIZE=1024
|
|
CONFIG_NSH_NESTDEPTH=3
|
|
CONFIG_NSH_DISABLESCRIPT=n
|
|
CONFIG_NSH_DISABLEBG=n
|
|
CONFIG_NSH_ROMFSETC=n
|
|
CONFIG_NSH_CONSOLE=y
|
|
CONFIG_NSH_TELNET=n
|
|
CONFIG_NSH_IOBUFFER_SIZE=512
|
|
CONFIG_NSH_DHCPC=n
|
|
CONFIG_NSH_NOMAC=y
|
|
CONFIG_NSH_IPADDR=(10L<<24|0L<<16|0L<<8|2L)
|
|
CONFIG_NSH_DRIPADDR=(10L<<24|0L<<16|0L<<8|1L)
|
|
CONFIG_NSH_NETMASK=(255L<<24|255L<<16|255L<<8|0L)
|
|
CONFIG_NSH_ROMFSMOUNTPT="/etc"
|
|
CONFIG_NSH_INITSCRIPT="init.d/rcS"
|
|
CONFIG_NSH_ROMFSDEVNO=0
|
|
CONFIG_NSH_ROMFSSECTSIZE=64
|
|
CONFIG_NSH_FATDEVNO=1
|
|
CONFIG_NSH_FATSECTSIZE=512
|
|
CONFIG_NSH_FATNSECTORS=1024
|
|
CONFIG_NSH_FATMOUNTPT=/tmp
|
|
|
|
#
|
|
# Architecture-specific NSH options
|
|
CONFIG_NSH_MMCSDSPIPORTNO=1
|
|
CONFIG_NSH_MMCSDSLOTNO=0
|
|
CONFIG_NSH_MMCSDMINOR=0
|
|
|
|
#
|
|
# Settings for examples/nx
|
|
#
|
|
# CONFIG_EXAMPLES_NX_VPLANE -- The plane to select from the frame-
|
|
# buffer driver for use in the test. Default: 0
|
|
# CONFIG_EXAMPLES_NX_BGCOLOR -- The color of the background. Default depends on
|
|
# CONFIG_EXAMPLES_NX_BPP.
|
|
# CONFIG_EXAMPLES_NX_COLOR1 -- The color of window 1. Default depends on
|
|
# CONFIG_EXAMPLES_NX_BPP.
|
|
# CONFIG_EXAMPLES_NX_COLOR2 -- The color of window 2. Default depends on
|
|
# CONFIG_EXAMPLES_NX_BPP.
|
|
# CONFIG_EXAMPLES_NX_TBCOLOR -- The color of the toolbar. Default depends on
|
|
# CONFIG_EXAMPLES_NX_BPP.
|
|
# CONFIG_EXAMPLES_NX_FONTCOLOR -- The color of the toolbar. Default depends on
|
|
# CONFIG_EXAMPLES_NX_BPP.
|
|
# CONFIG_EXAMPLES_NX_BPP -- Pixels per pixel to use. Valid options
|
|
# include 2, 4, 8, 16, 24, and 32. Default is 32.
|
|
# CONFIG_EXAMPLES_NX_RAWWINDOWS -- Use raw windows; Default is to
|
|
# use pretty, framed NXTK windows with toolbars.
|
|
# CONFIG_EXAMPLES_NX_STACKSIZE -- The stacksize to use when creating
|
|
# the NX server. Default 2048
|
|
# CONFIG_EXAMPLES_NX_CLIENTPRIO -- The client priority. Default: 80
|
|
# CONFIG_EXAMPLES_NX_SERVERPRIO -- The server priority. Default: 120
|
|
# CONFIG_EXAMPLES_NX_NOTIFYSIGNO -- The signal number to use with
|
|
# nx_eventnotify(). Default: 4
|
|
CONFIG_EXAMPLES_NX_VPLANE=0
|
|
#CONFIG_EXAMPLES_NX_BGCOLOR
|
|
#CONFIG_EXAMPLES_NX_COLOR1
|
|
#CONFIG_EXAMPLES_NX_COLOR2
|
|
#CONFIG_EXAMPLES_NX_TBCOLOR
|
|
#CONFIG_EXAMPLES_NX_FONTCOLOR
|
|
CONFIG_EXAMPLES_NX_BPP=CONFIG_SIM_FBBPP
|
|
CONFIG_EXAMPLES_NX_RAWWINDOWS=n
|
|
CONFIG_EXAMPLES_NX_STACKSIZE=8192
|
|
CONFIG_EXAMPLES_NX_CLIENTPRIO=80
|
|
CONFIG_EXAMPLES_NX_SERVERPRIO=120
|
|
CONFIG_EXAMPLES_NX_NOTIFYSIGNO=4
|
|
|
|
#
|
|
# Settings for examples/mount
|
|
CONFIG_EXAMPLES_MOUNT_DEVNAME="/dev/ram0"
|
|
#CONFIG_EXAMPLES_MOUNT_NSECTORS=2048
|
|
#CONFIG_EXAMPLES_MOUNT_SECTORSIZE=512
|
|
#CONFIG_EXAMPLES_MOUNT_RAMDEVNO=1
|
|
|
|
#
|
|
# Settings for examples/wget
|
|
# CONFIG_EXAMPLE_WGET_URL - The URL of the file to get
|
|
# CONFIG_EXAMPLE_WGET_NOMAC - (May be defined to use software assigned MAC)
|
|
# CONFIG_EXAMPLE_WGET_IPADDR - Target IP address
|
|
# CONFIG_EXAMPLE_WGET_DRIPADDR - Default router IP addess
|
|
# CONFIG_EXAMPLE_WGET_NETMASK - Network mask
|
|
CONFIG_EXAMPLE_WGET_URL="http://www.nuttx.org/index.html"
|
|
CONFIG_EXAMPLE_WGET_NOMAC=y
|
|
CONFIG_EXAMPLE_WGET_IPADDR=(10L<<24|0L<<16|0L<<8|2L)
|
|
CONFIG_EXAMPLE_WGET_DRIPADDR=(10L<<24|0L<<16|0L<<8|1L)
|
|
CONFIG_EXAMPLE_WGET_NETMASK=(255L<<24|255L<<16|255L<<8|0L)
|
|
|
|
#
|
|
# Stack and heap information
|
|
#
|
|
# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP
|
|
# operation from FLASH but must copy initialized .data sections to RAM.
|
|
# CONFIG_BOOT_COPYTORAM - Some configurations boot in FLASH
|
|
# but copy themselves entirely into RAM for better performance.
|
|
# CONFIG_CUSTOM_STACK - The up_ implementation will handle
|
|
# all stack operations outside of the nuttx model.
|
|
# CONFIG_STACK_POINTER - The initial stack pointer
|
|
# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack.
|
|
# This is the thread that (1) performs the inital boot of the system up
|
|
# to the point where user_start() is spawned, and (2) there after is the
|
|
# IDLE thread that executes only when there is no other thread ready to
|
|
# run.
|
|
# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate
|
|
# for the main user thread that begins at the user_start() entry point.
|
|
# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size
|
|
# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size
|
|
# CONFIG_HEAP_BASE - The beginning of the heap
|
|
# CONFIG_HEAP_SIZE - The size of the heap
|
|
#
|
|
CONFIG_BOOT_RUNFROMFLASH=n
|
|
CONFIG_BOOT_COPYTORAM=n
|
|
CONFIG_CUSTOM_STACK=n
|
|
CONFIG_STACK_POINTER=
|
|
CONFIG_IDLETHREAD_STACKSIZE=1024
|
|
CONFIG_USERMAIN_STACKSIZE=1024
|
|
CONFIG_PTHREAD_STACK_MIN=256
|
|
CONFIG_PTHREAD_STACK_DEFAULT=1024
|
|
CONFIG_HEAP_BASE=
|
|
CONFIG_HEAP_SIZE=
|