nuttx/boards/sama5d3-xplained/scripts/isram.ld
Alin Jerpelea a1c991d921 Merged in alinjerpelea/nuttx (pull request #963)
Move boards to boards folder

* boards: rename configs folder to boards

    This is the proposed layout after the change:

    boards: - folder containing board folders
            <board>: - name of each board
                    drivers: - extra drivers specific for platform
                    include: - header files for the boars
                    scripts: - extra scripts specific for platform
                        src: - board specific code
                      tools: - extra tools specific for platform
                    <config>: - board specific configuration(s)

    Note:
    <xxx> names are dependent on platform

    This is a logical change to aim to the arch layout but this is a
    huge change it should be done in several steps to lower the risk.

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* Kconfig: replace configs with boards

    The change is needed after the path change

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* Makefile: replace configs with boards

    The change is needed after the path change

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* Makefile.*: replace configs with boards

    The change is needed after the path change

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* Make.defs: replace configs with boards

    The change is needed after the path change

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* .sh: replace configs with boards

    The change is needed after the path change

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* .mk: replace configs with boards

    The change is needed after the path change

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* .c & .h: replace configs with boards

    The change is needed after the path change

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

* .bat: replace configs with boards

    The change is needed after the path change

    Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>

Approved-by: Gregory Nutt <gnutt@nuttx.org>
2019-08-05 12:04:14 +00:00

136 lines
3.7 KiB
Plaintext

/****************************************************************************
* configs/sama5d3-xplained/scripts/isram.ld
*
* Copyright (C) 2014, 2016 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
****************************************************************************/
/* The SAMA5D36 has 128 KB of ISRAM beginning at virtual address 0x0030:0000.
*
* Vectors in low memory are assumed and 16KB of ISRAM is reserved at the
* high end of ISRAM for the page table.
*/
MEMORY
{
isram (W!RX) : ORIGIN = 0x300000, LENGTH = 128K - 16K
}
OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
OUTPUT_ARCH(arm)
ENTRY(entry)
ENTRY(_stext)
SECTIONS
{
.text :
{
_stext = ABSOLUTE(.);
*(.vectors)
*(.text .text.*)
*(.fixup)
*(.gnu.warning)
*(.rodata .rodata.*)
*(.gnu.linkonce.t.*)
*(.glue_7)
*(.glue_7t)
*(.got)
*(.gcc_except_table)
*(.gnu.linkonce.r.*)
*(.ARM.extab*)
*(.gnu.linkonce.armextab.*)
_etext = ABSOLUTE(.);
} > isram
.init_section :
{
_sinit = ABSOLUTE(.);
*(.init_array .init_array.*)
_einit = ABSOLUTE(.);
} > isram
.ARM.extab :
{
*(.ARM.extab*)
} > isram
/* .ARM.exidx is sorted, so has to go in its own output section. */
PROVIDE_HIDDEN (__exidx_start = .);
.ARM.exidx :
{
*(.ARM.exidx* .gnu.linkonce.armexidx.*)
} > isram
PROVIDE_HIDDEN (__exidx_end = .);
.data :
{
_sdata = ABSOLUTE(.);
*(.data .data.*)
*(.gnu.linkonce.d.*)
CONSTRUCTORS
_edata = ABSOLUTE(.);
} > isram
.bss :
{
_sbss = ABSOLUTE(.);
*(.bss .bss.*)
*(.gnu.linkonce.b.*)
*(COMMON)
_ebss = ABSOLUTE(.);
} > isram
/* Uninitialized data */
.noinit :
{
_snoinit = ABSOLUTE(.);
*(.noinit*)
_enoinit = ABSOLUTE(.);
} > isram
/* Stabs debugging sections. */
.stab 0 : { *(.stab) }
.stabstr 0 : { *(.stabstr) }
.stab.excl 0 : { *(.stab.excl) }
.stab.exclstr 0 : { *(.stab.exclstr) }
.stab.index 0 : { *(.stab.index) }
.stab.indexstr 0 : { *(.stab.indexstr) }
.comment 0 : { *(.comment) }
.debug_abbrev 0 : { *(.debug_abbrev) }
.debug_info 0 : { *(.debug_info) }
.debug_line 0 : { *(.debug_line) }
.debug_pubnames 0 : { *(.debug_pubnames) }
.debug_aranges 0 : { *(.debug_aranges) }
}