56529d2944
- migrated /README are removed from /boards - there are a lot of READMEs that should be further converted to rst. At the moment they are moved to Documentation/platforms and included in rst files
137 lines
3.8 KiB
ReStructuredText
137 lines
3.8 KiB
ReStructuredText
===============================
|
|
Waveshare RP2040 LCD 1.28
|
|
===============================
|
|
|
|
The `Waveshare RP2040 LCD 1.28 <https://www.waveshare.com/wiki/RP2040-LCD-1.28>`_
|
|
is a low-cost, high-performance MCU board designed by Waveshare based on RP2040
|
|
with onboard 1.28 inch LCD.
|
|
|
|
.. figure:: RP2040-LCD-1.28.jpg
|
|
:align: center
|
|
|
|
Features
|
|
========
|
|
|
|
* RP2040 MCU chip designed by Raspberry Pi in the United Kingdom
|
|
* Dual-core Arm Cortex M0+ processor, flexible clock running up to 133 MHz
|
|
* 264KB of SRAM, and 2MB of onboard Flash memory
|
|
* Type-C connector, keeps it up to date, easier to use
|
|
* Onboard 1.28-inch 240 x 240 resolution, 65K RGB IPS LCD display for clear color pictures
|
|
* Lithium battery recharge/discharge header, suitable for mobile devices
|
|
* All GPIOs are adapted through 1.27 pitch female headers
|
|
(There are 30 pins in total, but some pins have been connected to the internal circuit,
|
|
you need to pay attention when multiplexing, please refer to the wiki for details)
|
|
* USB 1.1 with device and host support
|
|
* Low-power sleep and dormant modes
|
|
* Drag-and-drop programming using mass storage over USB
|
|
* 2 x SPI, 2 x I2C, 2 x UART, 2 x UART, 4 x 12-bit ADC, 16 x controllable PWM channels
|
|
* Accurate clock and timer on-chip
|
|
* Temperature sensor
|
|
* Accelerated floating-point libraries on-chip
|
|
* 8 x Programmable I/O (PIO) state machines for custom peripheral support
|
|
|
|
Serial Console
|
|
==============
|
|
|
|
By default a serial console appears on pins 1 (TX GPIO0) and pin 2
|
|
(RX GPIO1). This console runs a 115200-8N1.
|
|
|
|
The board can be configured to use the USB connection as the serial console.
|
|
|
|
Buttons and LEDs
|
|
================
|
|
|
|
No user LED is provided.
|
|
|
|
A BOOT button, which if held down when pressing RESET or power is first
|
|
applied to the board, will cause the RP2040 to boot into programming
|
|
mode and appear as a storage device to a computer connected via USB.
|
|
Saving a .UF2 file to this device will replace the Flash ROM contents
|
|
on the RP2040.
|
|
|
|
Pin Mapping
|
|
===========
|
|
|
|
===== ========== ==========
|
|
Pad Signal Notes
|
|
===== ========== ==========
|
|
2 GPIO0 Default TX for UART0 serial console
|
|
4 GPIO1 Default RX for UART0 serial console
|
|
===== ========== ==========
|
|
|
|
Power Supply
|
|
============
|
|
|
|
The Raspberry Pi Pico can be powered via the USB connector, connecting
|
|
a lithium battery through connector, or by supplying +5V to pin 18(VSYS).
|
|
The board had a diode that prevents power from pin 18 from flowing back
|
|
to the USB socket. Power through USB or VSYS will be charging the battery
|
|
if connected. The schematic is available at `RP2040-LCD-1.28-sch.pdf <https://www.waveshare.net/w/upload/6/60/RP2040-LCD-1.28-sch.pdf>`_
|
|
|
|
Configurations
|
|
==============
|
|
|
|
composite
|
|
---------
|
|
|
|
NuttShell configuration (console enabled in UART0, at 115200 bps) with support for
|
|
CDC/ACM with MSC USB composite driver.
|
|
|
|
nsh
|
|
---
|
|
|
|
Basic NuttShell configuration (console enabled in UART0, at 115200 bps).
|
|
|
|
nsh-flash
|
|
---------
|
|
|
|
Basic NuttShell configuration (console enabled in UART0, at 115200 bps
|
|
with SMART flash filesystem.
|
|
|
|
nshsram
|
|
-------
|
|
|
|
NuttShell configuration (console enabled in UART0, at 115200 bps) with interrupt
|
|
vectors in RAM.
|
|
|
|
smp
|
|
---
|
|
|
|
Basic NuttShell configuration (console enabled in UART0, at 115200 bps) with
|
|
both ARM cores enabled.
|
|
|
|
spisd
|
|
-----
|
|
|
|
NuttShell configuration (console enabled in UART0, at 115200 bps) with SPI configured.
|
|
|
|
usbmsc
|
|
------
|
|
|
|
NuttShell configuration (console enabled in UART0, at 115200 bps) with support for
|
|
usbmsc.
|
|
|
|
usbnsh
|
|
------
|
|
|
|
Basic NuttShell configuration (console enabled in USB Port, at 115200 bps).
|
|
|
|
fb
|
|
------------------
|
|
|
|
NuttShell configuration (console enabled in USB Port, at 115200 bps) with support for
|
|
gc9a01 and video framebuffer example.
|
|
|
|
lvgl
|
|
-----------------
|
|
|
|
NuttShell configuration (console enabled in USB Port, at 115200 bps) with support for
|
|
gc9a01 and LVGL demo (using lcd_dev).
|
|
|
|
|
|
README.txt
|
|
==========
|
|
|
|
.. include:: README.txt
|
|
:literal:
|