155 lines
3.8 KiB
ReStructuredText
155 lines
3.8 KiB
ReStructuredText
==============
|
||
ESP-WROVER-KIT
|
||
==============
|
||
|
||
The `ESP-WROVER-KIT <https://docs.espressif.com/projects/esp-idf/en/latest/esp32/hw-reference/esp32/get-started-wrover-kit.html>`_ is a development board for the ESP32 SoC from Espressif, based on a ESP32-WROVER-B module.
|
||
|
||
.. list-table::
|
||
:align: center
|
||
|
||
* - .. figure:: esp-wrover-kit-v4.1-layout-back.png
|
||
:align: center
|
||
|
||
ESP-WROVER-KIT board layout - front
|
||
|
||
- .. figure:: esp-wrover-kit-v4.1-layout-front.png
|
||
:align: center
|
||
|
||
ESP-WROVER-KIT board layout - back
|
||
|
||
Features
|
||
========
|
||
|
||
- ESP32-WROVER-B module
|
||
- LCD screen
|
||
- MicroSD card slot
|
||
|
||
Its another distinguishing feature is the embedded FTDI FT2232HL chip,
|
||
an advanced multi-interface USB bridge. This chip enables to use JTAG
|
||
for direct debugging of ESP32 through the USB interface without a separate
|
||
JTAG debugger. ESP-WROVER-KIT makes development convenient, easy, and
|
||
cost-effective.
|
||
|
||
Most of the ESP32 I/O pins are broken out to the board’s pin headers for easy access.
|
||
|
||
Serial Console
|
||
==============
|
||
|
||
UART0 is, by default, the serial console. It connects to the on-board
|
||
FT2232HL converter and is available on the USB connector USB CON8 (J5).
|
||
|
||
It will show up as /dev/ttyUSB[n] where [n] will probably be 1, since
|
||
the first interface ([n] == 0) is dedicated to the USB-to-JTAG interface.
|
||
|
||
Buttons and LEDs
|
||
================
|
||
|
||
Buttons
|
||
-------
|
||
|
||
There are two buttons labeled Boot and EN. The EN button is not available
|
||
to software. It pulls the chip enable line that doubles as a reset line.
|
||
|
||
The BOOT button is connected to IO0. On reset it is used as a strapping
|
||
pin to determine whether the chip boots normally or into the serial
|
||
bootloader. After reset, however, the BOOT button can be used for software
|
||
input.
|
||
|
||
LEDs
|
||
----
|
||
|
||
There are several on-board LEDs for that indicate the presence of power
|
||
and USB activity.
|
||
|
||
There is an RGB LED available for software.
|
||
|
||
Pin Mapping
|
||
===========
|
||
|
||
===== ========================= ==========
|
||
Pin Signal Notes
|
||
===== ========================= ==========
|
||
0 RGB LED Red / BOOT Button
|
||
2 RGB LED Green
|
||
4 RGB LED Blue
|
||
5 LCD Backlight
|
||
18 LCD Reset
|
||
19 LCD Clock
|
||
21 LCD D/C
|
||
22 LCD CS
|
||
23 LCD MOSI
|
||
25 LCD MISO
|
||
===== ========================= ==========
|
||
|
||
Configurations
|
||
==============
|
||
|
||
nsh
|
||
---
|
||
|
||
Basic NuttShell configuration (console enabled in UART0, exposed via
|
||
USB connection by means of FT2232HL converter, at 115200 bps).
|
||
|
||
wapi
|
||
----
|
||
|
||
Enables Wi-Fi support.
|
||
|
||
gpio
|
||
----
|
||
|
||
This is a test for the GPIO driver. It includes the 3 LEDs and one, arbitrary, GPIO.
|
||
For this example, GPIO22 was used.
|
||
At the nsh, we can turn LEDs on and off with the following::
|
||
|
||
nsh> gpio -o 1 /dev/gpio0
|
||
nsh> gpio -o 0 /dev/gpio0
|
||
|
||
We can use the interrupt pin to send a signal when the interrupt fires::
|
||
|
||
nsh> gpio -w 14 /dev/gpio2
|
||
|
||
The pin is configured to as a rising edge interrupt, so after issuing the
|
||
above command, connect it to 3.3V.
|
||
|
||
spiflash
|
||
--------
|
||
|
||
This config tests the external SPI that comes with an ESP32 module connected
|
||
through SPI1.
|
||
|
||
By default a SmartFS file system is selected.
|
||
Once booted you can use the following commands to mount the file system::
|
||
|
||
mksmartfs /dev/smart0
|
||
mount -t smartfs /dev/smart0 /mnt
|
||
|
||
Note that `mksmartfs` is only needed the first time.
|
||
|
||
nx
|
||
--
|
||
|
||
This config adds a set of tests using the graphic examples at `apps/example/nx`.
|
||
|
||
This configuration illustrates the use of the LCD with the lower performance
|
||
SPI interface.
|
||
|
||
lvgl
|
||
----
|
||
|
||
This is a demonstration of the LVGL graphics library running on the NuttX LCD
|
||
driver. You can find LVGL here::
|
||
|
||
https://www.lvgl.io/
|
||
https://github.com/lvgl/lvgl
|
||
|
||
This configuration uses the LVGL demonstration at `apps/examples/lvgldemo`.
|
||
|
||
External devices
|
||
=================
|
||
|
||
BMP180
|
||
------
|
||
|
||
When using BMP180 (enabling ``CONFIG_SENSORS_BMP180``), it's expected this device is wired to I2C0 bus.
|