241 lines
8.0 KiB
C
241 lines
8.0 KiB
C
/****************************************************************************
|
|
* boards/arm/at32/at32f437-mini/src/at32_ethernet.c
|
|
*
|
|
* Licensed to the Apache Software Foundation (ASF) under one or more
|
|
* contributor license agreements. See the NOTICE file distributed with
|
|
* this work for additional information regarding copyright ownership. The
|
|
* ASF licenses this file to you under the Apache License, Version 2.0 (the
|
|
* "License"); you may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at
|
|
*
|
|
* http://www.apache.org/licenses/LICENSE-2.0
|
|
*
|
|
* Unless required by applicable law or agreed to in writing, software
|
|
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
|
|
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
|
|
* License for the specific language governing permissions and limitations
|
|
* under the License.
|
|
*
|
|
****************************************************************************/
|
|
|
|
/****************************************************************************
|
|
* Included Files
|
|
****************************************************************************/
|
|
|
|
#include <nuttx/config.h>
|
|
|
|
/* Force verbose debug on in this file only to support unit-level testing. */
|
|
|
|
#ifdef CONFIG_NETDEV_PHY_DEBUG
|
|
# undef CONFIG_DEBUG_INFO
|
|
# define CONFIG_DEBUG_INFO 1
|
|
# undef CONFIG_DEBUG_NET
|
|
# define CONFIG_DEBUG_NET 1
|
|
#endif
|
|
|
|
#include <string.h>
|
|
#include <assert.h>
|
|
#include <errno.h>
|
|
#include <debug.h>
|
|
|
|
#include <nuttx/irq.h>
|
|
#include <nuttx/arch.h>
|
|
#include <nuttx/fs/ioctl.h>
|
|
#include <nuttx/mtd/mtd.h>
|
|
|
|
#include "at32_gpio.h"
|
|
#include "at32_eth.h"
|
|
|
|
#include "at32f437-mini.h"
|
|
|
|
#if defined(CONFIG_AT32_ETHMAC)
|
|
|
|
/****************************************************************************
|
|
* Pre-processor Definitions
|
|
****************************************************************************/
|
|
|
|
#define AT32_ETHMAC_DEVNAME "eth0"
|
|
|
|
#undef HAVE_NETMONITOR
|
|
|
|
/* Debug ********************************************************************/
|
|
|
|
/* Extra, in-depth debug output that is only available if
|
|
* CONFIG_NETDEV_PHY_DEBUG us defined.
|
|
*/
|
|
|
|
#ifdef CONFIG_NETDEV_PHY_DEBUG
|
|
# define phyerr _err
|
|
# define phywarn _warn
|
|
# define phyinfo _info
|
|
#else
|
|
# define phyerr(x...)
|
|
# define phywarn(x...)
|
|
# define phyinfo(x...)
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Private Data
|
|
****************************************************************************/
|
|
|
|
#ifdef HAVE_NETMONITOR
|
|
static xcpt_t g_ethmac_handler;
|
|
static void *g_ethmac_arg;
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Private Functions
|
|
****************************************************************************/
|
|
|
|
/****************************************************************************
|
|
* Name: at32_emac0_phy_enable
|
|
****************************************************************************/
|
|
|
|
#ifdef HAVE_NETMONITOR
|
|
static void at32_emac0_phy_enable(bool enable)
|
|
{
|
|
phyinfo("enable=%d\n", enable);
|
|
if (enable && g_ethmac_handler != NULL)
|
|
{
|
|
/* Attach and enable GPIO interrupt (and event) on the falling edge */
|
|
|
|
at32_gpiosetevent(GPIO_EMAC_NINT, false, true, true,
|
|
g_ethmac_handler, g_ethmac_arg);
|
|
}
|
|
else
|
|
{
|
|
/* Detach and disable GPIO interrupt */
|
|
|
|
at32_gpiosetevent(GPIO_EMAC_NINT, false, false, false,
|
|
NULL, NULL);
|
|
}
|
|
}
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Public Functions
|
|
****************************************************************************/
|
|
|
|
/****************************************************************************
|
|
* Name: at32_netinitialize
|
|
*
|
|
* Description:
|
|
* Configure board resources to support networking.
|
|
*
|
|
****************************************************************************/
|
|
|
|
void at32_netinitialize(void)
|
|
{
|
|
#ifdef HAVE_NETMONITOR
|
|
/* Configure the PHY interrupt GPIO */
|
|
|
|
phyinfo("Configuring %08x\n", GPIO_EMAC_NINT);
|
|
at32_configgpio(GPIO_EMAC_NINT);
|
|
#endif
|
|
|
|
/* Configure PHY /RESET output */
|
|
|
|
at32_configgpio(GPIO_EMAC_NRST);
|
|
}
|
|
|
|
/****************************************************************************
|
|
* Name: arch_phy_irq
|
|
*
|
|
* Description:
|
|
* This function may be called to register an interrupt handler that will
|
|
* be called when a PHY interrupt occurs. This function both attaches
|
|
* the interrupt handler and enables the interrupt if 'handler' is non-
|
|
* NULL. If handler is NULL, then the interrupt is detached and disabled
|
|
* instead.
|
|
*
|
|
* The PHY interrupt is always disabled upon return. The caller must
|
|
* call back through the enable function point to control the state of
|
|
* the interrupt.
|
|
*
|
|
* This interrupt may or may not be available on a given platform depending
|
|
* on how the network hardware architecture is implemented. In a typical
|
|
* case, the PHY interrupt is provided to board-level logic as a GPIO
|
|
* interrupt (in which case this is a board-specific interface and really
|
|
* should be called board_phy_irq()); In other cases, the PHY interrupt
|
|
* may be cause by the chip's MAC logic (in which case arch_phy_irq()) is
|
|
* an appropriate name. Other other boards, there may be no PHY interrupts
|
|
* available at all. If client attachable PHY interrupts are available
|
|
* from the board or from the chip, then CONFIG_ARCH_PHY_INTERRUPT should
|
|
* be defined to indicate that fact.
|
|
*
|
|
* Typical usage:
|
|
* a. OS service logic (not application logic*) attaches to the PHY
|
|
* PHY interrupt and enables the PHY interrupt.
|
|
* b. When the PHY interrupt occurs: (1) the interrupt should be
|
|
* disabled and () work should be scheduled on the worker thread (or
|
|
* perhaps a dedicated application thread).
|
|
* c. That worker thread should use the SIOCGMIIPHY, SIOCGMIIREG,
|
|
* and SIOCSMIIREG ioctl calls** to communicate with the PHY,
|
|
* determine what network event took place (Link Up/Down?), and
|
|
* take the appropriate actions.
|
|
* d. It should then interact the PHY to clear any pending
|
|
* interrupts, then re-enable the PHY interrupt.
|
|
*
|
|
* * This is an OS internal interface and should not be used from
|
|
* application space. Rather applications should use the SIOCMIISIG
|
|
* ioctl to receive a signal when a PHY event occurs.
|
|
* ** This interrupt is really of no use if the Ethernet MAC driver
|
|
* does not support these ioctl calls.
|
|
*
|
|
* Input Parameters:
|
|
* intf - Identifies the network interface. For example "eth0". Only
|
|
* useful on platforms that support multiple Ethernet interfaces
|
|
* and, hence, multiple PHYs and PHY interrupts.
|
|
* handler - The client interrupt handler to be invoked when the PHY
|
|
* asserts an interrupt. Must reside in OS space, but can
|
|
* signal tasks in user space. A value of NULL can be passed
|
|
* in order to detach and disable the PHY interrupt.
|
|
* arg - The argument that will accompany the interrupt
|
|
* enable - A function pointer that be unused to enable or disable the
|
|
* PHY interrupt.
|
|
*
|
|
* Returned Value:
|
|
* Zero (OK) returned on success; a negated errno value is returned on
|
|
* failure.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#ifdef HAVE_NETMONITOR
|
|
int arch_phy_irq(const char *intf, xcpt_t handler, void *arg,
|
|
phy_enable_t *enable)
|
|
{
|
|
phy_enable_t enabler;
|
|
irqstate_t flags;
|
|
|
|
ninfo("%s: handler=%p\n", intf, handler);
|
|
phyinfo("ETHMAC: devname=%s\n", AT32_ETHMAC_DEVNAME);
|
|
|
|
DEBUGASSERT(intf);
|
|
|
|
flags = enter_critical_section();
|
|
|
|
if (strcmp(intf, AT32_ETHMAC_DEVNAME) == 0)
|
|
{
|
|
phyinfo("Select ETHMAC\n");
|
|
g_ethmac_handler = handler;
|
|
g_ethmac_arg = arg;
|
|
enabler = at32_emac0_phy_enable;
|
|
}
|
|
else
|
|
{
|
|
nerr("ERROR: Unsupported interface: %s\n", intf);
|
|
enabler = NULL;
|
|
}
|
|
|
|
if (enable)
|
|
{
|
|
*enable = enabler;
|
|
}
|
|
|
|
leave_critical_section(flags);
|
|
return OK;
|
|
}
|
|
#endif
|
|
|
|
#endif /* CONFIG_AT32_ETHMAC */
|