000bf2a7c7
This commit use the new common RMT driver for all Espressif's xtensa-based chips on ESP32-S3.
256 lines
8.0 KiB
C
256 lines
8.0 KiB
C
/****************************************************************************
|
|
* boards/xtensa/esp32s3/esp32s3-devkit/src/esp32s3-devkit.h
|
|
*
|
|
* Licensed to the Apache Software Foundation (ASF) under one or more
|
|
* contributor license agreements. See the NOTICE file distributed with
|
|
* this work for additional information regarding copyright ownership. The
|
|
* ASF licenses this file to you under the Apache License, Version 2.0 (the
|
|
* "License"); you may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at
|
|
*
|
|
* http://www.apache.org/licenses/LICENSE-2.0
|
|
*
|
|
* Unless required by applicable law or agreed to in writing, software
|
|
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
|
|
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
|
|
* License for the specific language governing permissions and limitations
|
|
* under the License.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#ifndef __BOARDS_XTENSA_ESP32S3_ESP32S3_DEVKIT_SRC_ESP32S3_DEVKIT_H
|
|
#define __BOARDS_XTENSA_ESP32S3_ESP32S3_DEVKIT_SRC_ESP32S3_DEVKIT_H
|
|
|
|
/****************************************************************************
|
|
* Included Files
|
|
****************************************************************************/
|
|
|
|
#include <nuttx/config.h>
|
|
#include <nuttx/compiler.h>
|
|
#include <stdint.h>
|
|
|
|
/****************************************************************************
|
|
* Pre-processor Definitions
|
|
****************************************************************************/
|
|
|
|
/* ESP32-S3-DEVKIT GPIOs ****************************************************/
|
|
|
|
/* LCD pins, i.e. used by ST7735 */
|
|
|
|
#define GPIO_LCD_DC 14
|
|
#define GPIO_LCD_RST 9
|
|
|
|
/* BOOT Button */
|
|
|
|
#define BUTTON_BOOT 0
|
|
|
|
/* RMT gpio */
|
|
|
|
#define RMT_RXCHANNEL 4
|
|
#define RMT_TXCHANNEL 0
|
|
|
|
#ifdef CONFIG_RMT_LOOP_TEST_MODE
|
|
# define RMT_INPUT_PIN 0
|
|
# define RMT_OUTPUT_PIN 0
|
|
#else
|
|
# define RMT_INPUT_PIN 2
|
|
|
|
/* The on-board RGB LED pin differs depending on the board version */
|
|
|
|
# ifdef CONFIG_ESP32S3_DEVKITC_1_V10
|
|
# define RMT_OUTPUT_PIN 48
|
|
# else
|
|
# define RMT_OUTPUT_PIN 38
|
|
# endif
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Public Types
|
|
****************************************************************************/
|
|
|
|
/****************************************************************************
|
|
* Public Data
|
|
****************************************************************************/
|
|
|
|
#ifndef __ASSEMBLY__
|
|
|
|
/****************************************************************************
|
|
* Public Function Prototypes
|
|
****************************************************************************/
|
|
|
|
/****************************************************************************
|
|
* Name: esp32s3_bringup
|
|
*
|
|
* Description:
|
|
* Perform architecture-specific initialization
|
|
*
|
|
* CONFIG_BOARD_LATE_INITIALIZE=y :
|
|
* Called from board_late_initialize().
|
|
*
|
|
* CONFIG_BOARD_LATE_INITIALIZE=y && CONFIG_BOARDCTL=y :
|
|
* Called from the NSH library via board_app_initialize()
|
|
*
|
|
****************************************************************************/
|
|
|
|
int esp32s3_bringup(void);
|
|
|
|
/****************************************************************************
|
|
* Name: esp32s3_gpio_init
|
|
*
|
|
* Description:
|
|
* Configure the GPIO driver.
|
|
*
|
|
* Returned Value:
|
|
* Zero (OK) is returned on success; A negated errno value is returned
|
|
* to indicate the nature of any failure.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#ifdef CONFIG_DEV_GPIO
|
|
int esp32s3_gpio_init(void);
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Name: board_spiflash_init
|
|
*
|
|
* Description:
|
|
* Initialize the SPIFLASH and register the MTD device.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#ifdef CONFIG_ESP32S3_SPIFLASH
|
|
int board_spiflash_init(void);
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Name: board_i2c_init
|
|
*
|
|
* Description:
|
|
* Configure the I2C driver.
|
|
*
|
|
* Returned Value:
|
|
* Zero (OK) is returned on success; A negated errno value is returned
|
|
* to indicate the nature of any failure.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#ifdef CONFIG_I2C_DRIVER
|
|
int board_i2c_init(void);
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Name: board_bmp180_initialize
|
|
*
|
|
* Description:
|
|
* Initialize and register the BMP180 Pressure Sensor driver.
|
|
*
|
|
* Input Parameters:
|
|
* devno - The device number, used to build the device path as /dev/pressN
|
|
* busno - The I2C bus number
|
|
*
|
|
* Returned Value:
|
|
* Zero (OK) on success; a negated errno value on failure.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#ifdef CONFIG_SENSORS_BMP180
|
|
int board_bmp180_initialize(int devno, int busno);
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Name: board_i2sdev_initialize
|
|
*
|
|
* Description:
|
|
* This function is called by platform-specific, setup logic to configure
|
|
* and register the generic I2S audio driver. This function will register
|
|
* the driver as /dev/audio/pcm[x] where x is determined by the I2S port
|
|
* number.
|
|
*
|
|
* Input Parameters:
|
|
* port - The I2S port used for the device
|
|
* enable_tx - Register device as TX if true
|
|
* enable_rx - Register device as RX if true
|
|
*
|
|
* Returned Value:
|
|
* Zero is returned on success. Otherwise, a negated errno value is
|
|
* returned to indicate the nature of the failure.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#ifdef CONFIG_ESP32S3_I2S
|
|
int board_i2sdev_initialize(int port, bool enable_tx, bool enable_rx);
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Name: esp32s3_cs4344_initialize
|
|
*
|
|
* Description:
|
|
* This function is called by platform-specific, setup logic to configure
|
|
* and register the CS4344 device. This function will register the driver
|
|
* as /dev/audio/pcm[x] where x is determined by the I2S port number.
|
|
*
|
|
* Input Parameters:
|
|
* port - The I2S port used for the device
|
|
*
|
|
* Returned Value:
|
|
* Zero is returned on success. Otherwise, a negated errno value is
|
|
* returned to indicate the nature of the failure.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#ifdef CONFIG_AUDIO_CS4344
|
|
int esp32s3_cs4344_initialize(int port);
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Name: esp32s3_djoy_initialize
|
|
*
|
|
* Description:
|
|
* Initialize and register the discrete joystick driver
|
|
*
|
|
****************************************************************************/
|
|
|
|
#ifdef CONFIG_INPUT_DJOYSTICK
|
|
int esp32s3_djoy_initialize(void);
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Name: esp32s3_ledc_setup
|
|
*
|
|
* Description:
|
|
* Initialize LEDC PWM and register the PWM device.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#ifdef CONFIG_ESP32S3_LEDC
|
|
int esp32s3_pwm_setup(void);
|
|
#endif
|
|
|
|
#ifdef CONFIG_ESP32S3_TWAI
|
|
int esp32s3_twai_setup(void);
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Name: esp32s3_lan9250_initialize
|
|
*
|
|
* Description:
|
|
* This function is called by platform-specific setup logic to initialize
|
|
* the LAN9250 device. This function will register the driver
|
|
* as a network device.
|
|
*
|
|
* Input Parameters:
|
|
* port - The SPI port used for the device
|
|
*
|
|
* Returned Value:
|
|
* Zero is returned on success. Otherwise, a negated errno value is
|
|
* returned to indicate the nature of the failure.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#ifdef CONFIG_NET_LAN9250
|
|
int esp32s3_lan9250_initialize(int port);
|
|
#endif
|
|
|
|
#endif /* __ASSEMBLY__ */
|
|
#endif /* __BOARDS_XTENSA_ESP32S3_ESP32S3_DEVKIT_SRC_ESP32S3_DEVKIT_H */
|