a1c991d921
Move boards to boards folder
* boards: rename configs folder to boards
This is the proposed layout after the change:
boards: - folder containing board folders
<board>: - name of each board
drivers: - extra drivers specific for platform
include: - header files for the boars
scripts: - extra scripts specific for platform
src: - board specific code
tools: - extra tools specific for platform
<config>: - board specific configuration(s)
Note:
<xxx> names are dependent on platform
This is a logical change to aim to the arch layout but this is a
huge change it should be done in several steps to lower the risk.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Kconfig: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Makefile: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Makefile.*: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Make.defs: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .sh: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .mk: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .c & .h: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .bat: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
35 lines
956 B
INI
35 lines
956 B
INI
#daemon configuration
|
|
telnet_port 4444
|
|
gdb_port 3333
|
|
|
|
#interface
|
|
interface ft2232
|
|
ft2232_device_desc "Olimex OpenOCD JTAG A"
|
|
ft2232_layout "olimex-jtag"
|
|
ft2232_vid_pid 0x15BA 0x0003
|
|
jtag_speed 2
|
|
|
|
#use combined on interfaces or targets that can't set TRST/SRST separately
|
|
reset_config trst_and_srst separate
|
|
|
|
#jtag scan chain
|
|
#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
|
|
jtag_device 4 0x1 0xf 0xe
|
|
|
|
#target configuration
|
|
daemon_startup reset
|
|
|
|
#target <type> <startup mode>
|
|
#target arm9ejs <reset mode> <chainpos> <endianness> <variant>
|
|
target arm926ejs little run_and_halt 1 arm926ejs
|
|
run_and_halt_time 0 30
|
|
|
|
#target_script 0 reset oocd_flash2138.script
|
|
working_area 0 0x1102800 0x60000 nobackup
|
|
|
|
#flash configuration
|
|
#flash bank lpc2000 0x0 0x40000 0 0 0 lpc2000_v2 12000 calc_checksum
|
|
|
|
# For more information about the configuration files, take a look at:
|
|
# http://openfacts.berlios.de/index-en.phtml?title=Open+On-Chip+Debugger
|