nuttx/boards/arm/s32k1xx/s32k144evb
2022-12-13 19:50:01 +08:00
..
configs/nsh
include NXP S32K1XX boards: add up_perf_init to support SEGGER SystemView 2022-08-01 16:32:41 +03:00
scripts Move warning option from Make.defs to Toolchain.defs 2022-05-15 15:40:35 +03:00
src S32K automatically calculate size of periphclocks array 2022-12-13 19:50:01 +08:00
Kconfig
README.txt

README
======

This directory holds the port to the NXP S32K144EVB-Q100 development board.

Contents
========

  o Status
  o Serial Console
  o LEDs and Buttons
  o OpenSDA Notes
  o Thread-Aware Debugging with Eclipse
  o Configurations

Status
======

  2020-01-23:  Configuration created (copy-paste from S32K146EVB).
    Tested: Serial console, I2C, SPI.

  2020-06-15:  Added FlexCAN driver with SocketCAN support to the S32K1XX
    arch.  Should work also on the S32K144EVB board, but remains untested.

  2020-06-16:  Added Emulated EEPROM driver and initialization.

Serial Console
==============

  By default, the serial console will be provided on the OpenSDA VCOM port:

    OpenSDA UART RX  PTC6  (LPUART1_RX)
    OpenSDA UART TX  PTC7  (LPUART1_TX)

  USB drivers for the PEmicro CDC Serial Port are available here:
  http://www.pemicro.com/opensda/

LEDs and Buttons
================

  LEDs
  ----
  The S32K144EVB has one RGB LED:

    RedLED    PTD15  (FTM0 CH0)
    GreenLED  PTD16  (FTM0 CH1)
    BlueLED   PTD0   (FTM0 CH2)

  An output of '0' illuminates the LED.

  If CONFIG_ARCH_LEDS is not defined, then the user can control the LEDs in
  any way.  The following definitions are used to access individual RGB
  components (see s32k144evb.h):

    GPIO_LED_R
    GPIO_LED_G
    GPIO_LED_B

  The RGB components could, alternatively, be controlled through PWM using
  the common RGB LED driver.

  If CONFIG_ARCH_LEDs is defined, then NuttX will control the LEDs on board
  the S32K144EVB.  The following definitions describe how NuttX controls the
  LEDs:

    ==========================================+========+========+=========
                                                 RED     GREEN     BLUE
    ==========================================+========+========+=========

    LED_STARTED      NuttX has been started      OFF      OFF      OFF
    LED_HEAPALLOCATE Heap has been allocated     OFF      OFF      ON
    LED_IRQSENABLED  Interrupts enabled          OFF      OFF      ON
    LED_STACKCREATED Idle stack created          OFF      ON       OFF
    LED_INIRQ        In an interrupt                   (no change)
    LED_SIGNAL       In a signal handler               (no change)
    LED_ASSERTION    An assertion failed               (no change)
    LED_PANIC        The system has crashed      FLASH    OFF      OFF
    LED_IDLE         S32K144 in sleep mode             (no change)
    ==========================================+========+========+=========

  Buttons
  -------
  The S32K144EVB supports two buttons:

    SW2  PTC12
    SW3  PTC13

OpenSDA Notes
=============

  - USB drivers for the PEmicro CDC Serial Port are available here:
    http://www.pemicro.com/opensda/

  - The drag'n'drog interface expects files in .srec format.

  - Using Segger J-Link:  Easy... but remember to use the SWD connector J14
    in the center of the board and not the OpenSDA connector closer to the
    OpenSDA USB connector J7.

Thread-Aware Debugging with Eclipse
===================================

  Thread-aware debugging is possible with openocd-nuttx
  ( https://github.com/sony/openocd-nuttx ) and was tested together with the
  Eclipse-based S32 Design Studio for Arm:  
  https://www.nxp.com/design/software/development-software/s32-design-studio-ide/s32-design-studio-for-arm:S32DS-ARM

  NOTE: This method was last tested with NuttX 8.2 and S32DS for Arm 2018.R1.
  It may not work anymore with recent releases of NuttX and/or S32DS.

  1. NuttX should be build with debug symbols enabled.

  2. Build OpenOCD as described here (using the same parameters as well):
     https://micro.ros.org/docs/tutorials/old/debugging/

  3. A s32k144.cfg file is available in the scripts/ folder.  Start OpenOCD
     with the following command (adapt the path info):
     /usr/local/bin/openocd -f /usr/share/openocd/scripts/interface/jlink.cfg \
     -f boards/s32k1xx/s32k144evb/scripts/s32k144.cfg -c init -c "reset halt"

  4. Setup a GDB debug session in Eclipse.  The resulting debug window shows
     the NuttX threads.  The full stack details can be viewed.

Configurations
==============

  Common Information
  ------------------
  Each S32K144EVB configuration is maintained in a sub-directory and can be
  selected as follows:

    tools/configure.sh s32k144evb:<subdir>

  Where <subdir> is one of the sub-directories listed in the next paragraph.

    NOTES (common for all configurations):

    1. This configuration uses the mconf-based configuration tool.  To change
       this configuration using that tool, you should:

       a. Build and install the kconfig-mconf tool.  See nuttx/README.txt.
          Also see additional README.txt files in the NuttX tools repository.

       b. Execute 'make menuconfig' in nuttx/ in order to start the
          reconfiguration process.

    2. Unless otherwise stated, the serial console used is LPUART1 at
       115,200 8N1.  This corresponds to the OpenSDA VCOM port.

  Configuration Sub-directories
  -----------------------------

    nsh:
    ---
      Configures the NuttShell (nsh) located at apps/examples/nsh.  Support
      for builtin applications is enabled, but in the base configuration the
      only application selected is the "Hello, World!" example.