sergiotarxz/nuttx
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
b60f01a55b
nuttx/drivers/sensors/hdc1008.c
chao an b60f01a55b inode/i_private: remove all unnecessary cast for i_private 
Signed-off-by: chao an <anchao@xiaomi.com>
2023-08-29 08:58:07 +02:00

1007 lines
26 KiB
C
Raw Blame History

/****************************************************************************
* drivers/sensors/hdc1008.c
*
* Licensed to the Apache Software Foundation (ASF) under one or more
* contributor license agreements. See the NOTICE file distributed with
* this work for additional information regarding copyright ownership. The
* ASF licenses this file to you under the Apache License, Version 2.0 (the
* "License"); you may not use this file except in compliance with the
* License. You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
* License for the specific language governing permissions and limitations
* under the License.
*
****************************************************************************/
/****************************************************************************
* Included Files
****************************************************************************/
#include <nuttx/config.h>
#include <stdio.h>
#include <assert.h>
#include <errno.h>
#include <debug.h>
#include <time.h>
#include <nuttx/kmalloc.h>
#include <nuttx/mutex.h>
#include <nuttx/fs/fs.h>
#include <nuttx/i2c/i2c_master.h>
#include <nuttx/sensors/hdc1008.h>
#include <nuttx/random.h>
#include <nuttx/signal.h>
#if defined(CONFIG_I2C) && defined(CONFIG_SENSORS_HDC1008)
/****************************************************************************
* Pre-processor Definitions
****************************************************************************/
#ifdef CONFIG_HDC1008_DEBUG
# define hdc1008_dbg(x, ...) _info(x, ##__VA_ARGS__)
#else
# define hdc1008_dbg(x, ...) sninfo(x, ##__VA_ARGS__)
#endif
#ifndef CONFIG_SHT21_I2C_FREQUENCY
# define CONFIG_SHT21_I2C_FREQUENCY 400000
#endif
/* Macros to convert raw temperature and humidity to real values. Temperature
* is scaled by 100, humidity by 10.
*/
#define RAW_TO_TEMP(x) (((x) * 16500 / 65536) - 4000)
#define RAW_TO_RH(x) ((x) * 1000 / 65536)
/* Resolution for measurements. 8-bit is only valid for humidity. */
#define CONFIGURATION_RES_14BIT 0x00
#define CONFIGURATION_RES_11BIT 0x01
#define CONFIGURATION_RES_8BIT 0x02
/* HDC1008 registers */
#define HDC1008_REG_TEMPERATURE 0x00
#define HDC1008_REG_HUMIDITY 0x01
#define HDC1008_REG_CONFIGURATION 0x02
#define HDC1008_REG_SERIALID_0 0xFB /* Bits 0-15: Bit 24-39 of serial */
#define HDC1008_REG_SERIALID_1 0xFC /* Bits 0-15: Bit 8-23 of serial */
#define HDC1008_REG_SERIALID_2 0xFD /* Bits 7-15: Bit 0-7 of serial */
/* Configuration register bits */
#define HDC1008_CONFIGURATION_HRES_SHIFT (8) /* Bits 8-9: Humidity resolution */
#define HDC1008_CONFIGURATION_HRES_MASK (0x03 << HDC1008_CONFIGURATION_HRES_SHIFT)
# define HDC1008_CONFIGURATION_HRES_14BIT (CONFIGURATION_RES_14BIT << HDC1008_CONFIGURATION_HRES_SHIFT)
# define HDC1008_CONFIGURATION_HRES_11BIT (CONFIGURATION_RES_11BIT << HDC1008_CONFIGURATION_HRES_SHIFT)
# define HDC1008_CONFIGURATION_HRES_8BIT (CONFIGURATION_RES_8BIT << HDC1008_CONFIGURATION_HRES_SHIFT)
#define HDC1008_CONFIGURATION_TRES_SHIFT (10) /* Bit 10: Temperature resolution */
#define HDC1008_CONFIGURATION_TRES_MASK (0x01 << HDC1008_CONFIGURATION_TRES_SHIFT)
# define HDC1008_CONFIGURATION_TRES_14BIT (CONFIGURATION_RES_14BIT << HDC1008_CONFIGURATION_TRES_SHIFT)
# define HDC1008_CONFIGURATION_TRES_11BIT (CONFIGURATION_RES_11BIT << HDC1008_CONFIGURATION_TRES_SHIFT)
#define HDC1008_CONFIGURATION_BTST (1 << 11) /* Bit 11: Battery status */
#define HDC1008_CONFIGURATION_MODE (1 << 12) /* Bit 12: Mode of acquisition */
#define HDC1008_CONFIGURATION_HEAT_SHIFT (13) /* Bit 13: Heater */
#define HDC1008_CONFIGURATION_HEAT_MASK (0x01 << HDC1008_CONFIGURATION_HEAT_SHIFT)
# define HDC1008_CONFIGURATION_HEAT_DISABLE (0x00 << HDC1008_CONFIGURATION_HEAT_SHIFT)
# define HDC1008_CONFIGURATION_HEAT_ENABLE (0x01 << HDC1008_CONFIGURATION_HEAT_SHIFT)
/* Bit 14: Reserved */
#define HDC1008_CONFIGURATION_RST (1 << 15) /* Bit 15: Software reset bit */
/****************************************************************************
* Private
****************************************************************************/
struct hdc1008_dev_s
{
FAR struct i2c_master_s *i2c; /* I2C interface */
uint8_t addr; /* I2C address */
#ifndef CONFIG_DISABLE_PSEUDOFS_OPERATIONS
bool unlinked; /* True, driver has been unlinked */
#endif
uint8_t mode; /* Acquisition mode */
uint16_t configuration; /* Configuration shadow register */
#ifndef CONFIG_DISABLE_PSEUDOFS_OPERATIONS
int16_t crefs; /* Number of open references */
#endif
mutex_t devlock;
};
/****************************************************************************
* Private Function Prototypes
****************************************************************************/
/* Character driver methods */
#ifndef CONFIG_DISABLE_PSEUDOFS_OPERATIONS
static int hdc1008_open(FAR struct file *filep);
static int hdc1008_close(FAR struct file *filep);
#endif
static ssize_t hdc1008_read(FAR struct file *filep, FAR char *buffer,
size_t buflen);
static ssize_t hdc1008_write(FAR struct file *filep, FAR const char *buffer,
size_t buflen);
static int hdc1008_ioctl(FAR struct file *filep, int cmd,
unsigned long arg);
#ifndef CONFIG_DISABLE_PSEUDOFS_OPERATIONS
static int hdc1008_unlink(FAR struct inode *inode);
#endif
static int hdc1008_getreg(FAR struct hdc1008_dev_s *priv, uint8_t regaddr,
FAR uint16_t *regval);
static int hdc1008_putreg(FAR struct hdc1008_dev_s *priv, uint8_t regaddr,
FAR uint16_t regval);
static int hdc1008_reset(FAR struct hdc1008_dev_s *priv);
static int hdc1008_measure_trh(FAR struct hdc1008_dev_s *priv, int *t,
int *h);
static int hdc1008_measure_current_mode(struct hdc1008_dev_s *priv,
struct hdc1008_conv_data_s *data);
/****************************************************************************
* Private Data
****************************************************************************/
static const struct file_operations g_hdc1008fops =
{
#ifndef CONFIG_DISABLE_PSEUDOFS_OPERATIONS
hdc1008_open, /* open */
hdc1008_close, /* close */
#else
NULL, /* open */
NULL, /* close */
#endif
hdc1008_read, /* read */
hdc1008_write, /* write */
NULL, /* seek */
hdc1008_ioctl, /* ioctl */
NULL, /* mmap */
NULL, /* truncate */
NULL /* poll */
#ifndef CONFIG_DISABLE_PSEUDOFS_OPERATIONS
, hdc1008_unlink /* unlink */
#endif
};
/****************************************************************************
* Private Functions
****************************************************************************/
/****************************************************************************
* Name: hdc1008_measure_trh
*
* Description:
* Read both temperature and humidity from the sensor
*
****************************************************************************/
static int hdc1008_measure_trh(FAR struct hdc1008_dev_s *priv, int *t,
int *h)
{
struct i2c_config_s config;
uint8_t buf[4];
uint8_t reg = HDC1008_REG_TEMPERATURE;
int tmp;
int ret;
config.frequency = CONFIG_HDC1008_I2C_FREQUENCY;
config.address = priv->addr;
config.addrlen = 7;
ret = i2c_write(priv->i2c, &config, &reg, 1);
/* Wait for measurement to complete. Max should be about 20 ms if measuring
* both temperature and humidity.
*/
nxsig_usleep(20000);
ret = i2c_read(priv->i2c, &config, buf, 4);
if (ret < 0)
{
return ret;
}
/* Convert raw data from sensor to temperature/humidity */
tmp = ((int)buf[0] << 8) | (int)buf[1];
tmp = RAW_TO_TEMP(tmp);
*t = tmp;
tmp = ((int)buf[2] << 8) | (int)buf[3];
tmp = RAW_TO_RH(tmp);
*h = tmp;
return 0;
}
/****************************************************************************
* Name: hdc1008_measure_t_or_rh
*
* Description:
* Read both temperature and humidity from the sensor
*
****************************************************************************/
static int hdc1008_measure_t_or_rh(FAR struct hdc1008_dev_s *priv,
bool temperature, int *val)
{
struct i2c_config_s config;
uint8_t buf[4];
uint8_t reg;
int tmp;
int ret;
config.frequency = CONFIG_HDC1008_I2C_FREQUENCY;
config.address = priv->addr;
config.addrlen = 7;
reg = temperature ? HDC1008_REG_TEMPERATURE : HDC1008_REG_HUMIDITY;
ret = i2c_write(priv->i2c, &config, &reg, 1);
/* Wait for measurement to complete. 10 ms wait should give enough
* margin for either temperature/humidity at maximum resolution.
*/
nxsig_usleep(10000);
ret = i2c_read(priv->i2c, &config, buf, 2);
if (ret < 0)
{
return ret;
}
/* Convert raw data from sensor to temperature/humidity */
tmp = ((int)buf[0] << 8) | (int)buf[1];
tmp = temperature ? RAW_TO_TEMP(tmp) : RAW_TO_RH(tmp);
*val = tmp;
return 0;
}
/****************************************************************************
* Name: hdc1008_set_operational_mode
*
* Description:
* Configure the HDC1008 for measuring humitidy, temperature or both.
*
****************************************************************************/
static int hdc1008_set_operational_mode(struct hdc1008_dev_s *priv,
uint8_t mode)
{
int ret;
uint16_t reg;
ret = hdc1008_getreg(priv, HDC1008_REG_CONFIGURATION, &reg);
if (ret < 0)
{
return ret;
}
switch (mode)
{
case HDC1008_MEAS_TEMPERATURE:
{
reg &= ~HDC1008_CONFIGURATION_MODE;
break;
}
case HDC1008_MEAS_HUMIDITY:
{
reg &= ~HDC1008_CONFIGURATION_MODE;
break;
}
case HDC1008_MEAS_T_AND_RH:
{
reg |= HDC1008_CONFIGURATION_MODE;
break;
}
default:
return -EINVAL;
}
priv->mode = mode;
return hdc1008_putreg(priv, HDC1008_REG_CONFIGURATION, reg);
}
/****************************************************************************
* Name: hdc1008_set_temperature_resolution
*
* Description:
* Configure the HDC1008 temperature resolution
*
****************************************************************************/
static int hdc1008_set_temperature_resolution(struct hdc1008_dev_s *priv,
uint8_t resolution)
{
int ret;
uint16_t reg;
ret = hdc1008_getreg(priv, HDC1008_REG_CONFIGURATION, &reg);
if (ret < 0)
{
return ret;
}
reg &= ~HDC1008_CONFIGURATION_TRES_MASK;
switch (resolution)
{
case 11:
{
reg |= HDC1008_CONFIGURATION_TRES_11BIT;
break;
}
case 14:
{
reg |= HDC1008_CONFIGURATION_TRES_14BIT;
break;
}
default:
return -EINVAL;
}
return hdc1008_putreg(priv, HDC1008_REG_CONFIGURATION, reg);
}
/****************************************************************************
* Name: hdc1008_set_humidity_resolution
*
* Description:
* Configure the HDC1008 humidity resolution
*
****************************************************************************/
static int hdc1008_set_humidity_resolution(struct hdc1008_dev_s *priv,
uint8_t resolution)
{
int ret;
uint16_t reg;
ret = hdc1008_getreg(priv, HDC1008_REG_CONFIGURATION, &reg);
if (ret < 0)
{
return ret;
}
reg &= ~HDC1008_CONFIGURATION_HRES_MASK;
switch (resolution)
{
case 8:
{
reg |= HDC1008_CONFIGURATION_HRES_8BIT;
break;
}
case 11:
{
reg |= HDC1008_CONFIGURATION_HRES_11BIT;
break;
}
case 14:
{
reg |= HDC1008_CONFIGURATION_HRES_14BIT;
break;
}
default:
return -EINVAL;
}
return hdc1008_putreg(priv, HDC1008_REG_CONFIGURATION, reg);
}
/****************************************************************************
* Name: hdc1008_set_heater_mode
*
* Description:
* Configure the HDC1008 heater mode
*
****************************************************************************/
static int hdc1008_set_heater_mode(struct hdc1008_dev_s *priv,
uint8_t mode)
{
int ret;
uint16_t reg;
ret = hdc1008_getreg(priv, HDC1008_REG_CONFIGURATION, &reg);
if (ret < 0)
{
return ret;
}
reg &= ~HDC1008_CONFIGURATION_HEAT_MASK;
if (mode == 0)
{
reg |= HDC1008_CONFIGURATION_HEAT_DISABLE;
}
else if (mode == 1)
{
reg |= HDC1008_CONFIGURATION_HEAT_ENABLE;
}
else
{
return -EINVAL;
}
return hdc1008_putreg(priv, HDC1008_REG_CONFIGURATION, reg);
}
/****************************************************************************
* Name: hdc1008_getreg
*
* Description:
* Get value of 16-bit register
*
****************************************************************************/
static int hdc1008_getreg(FAR struct hdc1008_dev_s *priv, uint8_t regaddr,
FAR uint16_t *regval)
{
int ret;
struct i2c_config_s config;
uint8_t buf[2];
config.frequency = CONFIG_HDC1008_I2C_FREQUENCY;
config.address = priv->addr;
config.addrlen = 7;
ret = i2c_write(priv->i2c, &config, &regaddr, 1);
if (ret < 0)
{
return ret;
}
ret = i2c_read(priv->i2c, &config, buf, 2);
if (ret < 0)
{
return ret;
}
*regval = (buf[0] << 8) | buf[1];
return ret;
}
/****************************************************************************
* Name: hdc1008_putreg
*
* Description:
* Set value of 16-bit register
*
****************************************************************************/
static int hdc1008_putreg(FAR struct hdc1008_dev_s *priv, uint8_t regaddr,
FAR uint16_t regval)
{
struct i2c_config_s config;
uint8_t buf[3];
config.frequency = CONFIG_HDC1008_I2C_FREQUENCY;
config.address = priv->addr;
config.addrlen = 7;
hdc1008_dbg("addr=%02x; reg=%02x; val=%04x\n", priv->addr, regaddr,
regval);
buf[0] = regaddr;
buf[1] = (uint8_t)((regval >> 8) & 0xff);
buf[2] = (uint8_t)(regval & 0xff);
return i2c_write(priv->i2c, &config, buf, 3);
}
/****************************************************************************
* Name: hdc1008_open
*
* Description:
* This function is called whenever the hdc1008 device is opened.
*
****************************************************************************/
#ifndef CONFIG_DISABLE_PSEUDOFS_OPERATIONS
static int hdc1008_open(FAR struct file *filep)
{
FAR struct inode *inode = filep->f_inode;
FAR struct hdc1008_dev_s *priv = inode->i_private;
int ret;
ret = nxmutex_lock(&priv->devlock);
if (ret < 0)
{
return ret;
}
/* Increases the reference count */
++priv->crefs;
DEBUGASSERT(priv->crefs > 0);
nxmutex_unlock(&priv->devlock);
return 0;
}
#endif
/****************************************************************************
* Name: hdc1008_close
*
* Description:
* This routine is called when the hdc1008 device is closed.
*
****************************************************************************/
#ifndef CONFIG_DISABLE_PSEUDOFS_OPERATIONS
static int hdc1008_close(FAR struct file *filep)
{
FAR struct inode *inode = filep->f_inode;
FAR struct hdc1008_dev_s *priv = inode->i_private;
int ret;
ret = nxmutex_lock(&priv->devlock);
if (ret < 0)
{
return ret;
}
/* Decrement the reference count */
DEBUGASSERT(priv->crefs > 0);
--priv->crefs;
/* If the reference count is zero, and the driver has been unlinked, free
* the memory.
*/
if ((priv->crefs <= 0) && priv->unlinked)
{
nxmutex_destroy(&priv->devlock);
kmm_free(priv);
return OK;
}
nxmutex_unlock(&priv->devlock);
return OK;
}
#endif
/****************************************************************************
* Name: hdc1008_read
*
* Description:
* Called when the driver is read from.
*
****************************************************************************/
static ssize_t hdc1008_read(FAR struct file *filep, FAR char *buffer,
size_t buflen)
{
FAR struct inode *inode = filep->f_inode;
FAR struct hdc1008_dev_s *priv = inode->i_private;
int ret;
int len = 0;
struct hdc1008_conv_data_s data;
/* Sanity check of input buffer argument */
if (buffer == NULL)
{
return -EINVAL;
}
/* Get exclusive access */
ret = nxmutex_lock(&priv->devlock);
if (ret < 0)
{
return (ssize_t)ret;
}
#ifndef CONFIG_DISABLE_PSEUDOFS_OPERATIONS
if (priv->unlinked)
{
/* The driver is unliked, access is not allowed */
nxmutex_unlock(&priv->devlock);
return -ENODEV;
}
#endif
ret = hdc1008_measure_current_mode(priv, &data);
if (ret < 0)
{
nxmutex_unlock(&priv->devlock);
return ret;
}
if (priv->mode == HDC1008_MEAS_TEMPERATURE)
{
len = snprintf(buffer, buflen, "%d.%02d", data.temperature / 100,
data.temperature % 100);
}
else if (priv->mode == HDC1008_MEAS_HUMIDITY)
{
len = snprintf(buffer, buflen, "%d.%d", data.humidity / 10,
data.humidity % 10);
}
else if (priv->mode == HDC1008_MEAS_T_AND_RH)
{
len = snprintf(buffer, buflen, "%d.%02d %d.%d",
data.temperature / 100, data.temperature % 100,
data.humidity / 10, data.humidity % 10);
}
else
{
nxmutex_unlock(&priv->devlock);
return -EINVAL;
}
nxmutex_unlock(&priv->devlock);
return len;
}
/****************************************************************************
* Name: hdc1008_measure_current_mode
*
* Description:
* Measure from sensor according to current mode (temperature, humidity or
* both).
*
****************************************************************************/
static int hdc1008_measure_current_mode(struct hdc1008_dev_s *priv,
struct hdc1008_conv_data_s *data)
{
int ret;
int temperature;
int humidity;
switch (priv->mode)
{
case HDC1008_MEAS_TEMPERATURE:
ret = hdc1008_measure_t_or_rh(priv, true, &temperature);
if (ret < 0)
{
return ret;
}
data->temperature = temperature;
break;
case HDC1008_MEAS_HUMIDITY:
ret = hdc1008_measure_t_or_rh(priv, false, &humidity);
if (ret < 0)
{
return ret;
}
data->humidity = humidity;
break;
case HDC1008_MEAS_T_AND_RH:
ret = hdc1008_measure_trh(priv, &temperature, &humidity);
if (ret < 0)
{
return ret;
}
data->temperature = temperature;
data->humidity = humidity;
break;
default:
ret = -EINVAL;
break;
}
return ret;
}
/****************************************************************************
* Name: hdc1008_write
*
* Description:
* Called when the driver is written to (not supported).
*
****************************************************************************/
static ssize_t hdc1008_write(FAR struct file *filep, FAR const char *buffer,
size_t buflen)
{
return -ENOSYS;
}
/****************************************************************************
* Name: hdc1008_ioctl
*
* Description:
* Called when an ioctl() operation is made for the driver.
*
****************************************************************************/
static int hdc1008_ioctl(FAR struct file *filep, int cmd, unsigned long arg)
{
FAR struct inode *inode = filep->f_inode;
FAR struct hdc1008_dev_s *priv = inode->i_private;
int ret;
/* Get exclusive access */
ret = nxmutex_lock(&priv->devlock);
if (ret < 0)
{
return (ssize_t)ret;
}
#ifndef CONFIG_DISABLE_PSEUDOFS_OPERATIONS
if (priv->unlinked)
{
/* The driver is unliked, access is not allowed */
nxmutex_unlock(&priv->devlock);
return -ENODEV;
}
#endif
switch (cmd)
{
case SNIOC_RESET:
{
ret = hdc1008_reset(priv);
hdc1008_dbg("reset ret: %d\n", ret);
break;
}
case SNIOC_SET_OPERATIONAL_MODE:
{
ret = hdc1008_set_operational_mode(priv, (uint8_t)arg);
hdc1008_dbg("opmode ret: %d\n", ret);
break;
}
case SNIOC_SET_RESOLUTION_T:
{
ret = hdc1008_set_temperature_resolution(priv, (uint8_t)arg);
hdc1008_dbg("tres ret: %d\n", ret);
break;
}
case SNIOC_SET_RESOLUTION_RH:
{
ret = hdc1008_set_humidity_resolution(priv, (uint8_t)arg);
hdc1008_dbg("hres ret: %d\n", ret);
break;
}
case SNIOC_SET_HEATER_MODE:
{
ret = hdc1008_set_heater_mode(priv, (uint8_t)arg);
hdc1008_dbg("heater ret: %d\n", ret);
break;
}
case SNIOC_GET_CONFIGURATION:
{
uint16_t reg;
ret = hdc1008_getreg(priv, HDC1008_REG_CONFIGURATION, &reg);
if (ret >= 0)
{
*(uint16_t *)arg = reg;
}
hdc1008_dbg("read config ret: %d\n", ret);
break;
}
case SNIOC_MEASURE:
{
struct hdc1008_conv_data_s data;
ret = hdc1008_measure_current_mode(priv, &data);
if (ret >= 0)
memcpy((struct hdc1008_conv_data_s *)arg, &data, sizeof(data));
break;
}
default:
{
hdc1008_dbg("unrecognized cmd: %d\n", cmd);
_info("unknown cmd: %d\n", cmd);
ret = -ENOTTY;
break;
}
}
nxmutex_unlock(&priv->devlock);
return ret;
}
/****************************************************************************
* Name: hdc1008_unlink
*
* Description:
* Called when the driver is unlinked.
*
****************************************************************************/
#ifndef CONFIG_DISABLE_PSEUDOFS_OPERATIONS
static int hdc1008_unlink(FAR struct inode *inode)
{
FAR struct hdc1008_dev_s *priv;
int ret;
DEBUGASSERT((inode != NULL) && (inode->i_private != NULL));
priv = inode->i_private;
ret = nxmutex_lock(&priv->devlock);
if (ret < 0)
{
return ret;
}
/* Are there any open references to the driver? */
if (priv->crefs <= 0)
{
nxmutex_destroy(&priv->devlock);
kmm_free(priv);
return OK;
}
/* We still have open references, mark driver as unliked and wait for
* everyone to close their instance.
*/
priv->unlinked = true;
nxmutex_unlock(&priv->devlock);
return OK;
}
#endif
/****************************************************************************
* Name: hdc1008_reset
*
* Description:
* Perform a software reset of the sensor
*
****************************************************************************/
static int hdc1008_reset(FAR struct hdc1008_dev_s *priv)
{
int ret;
int count = 10;
uint16_t reg;
ret = hdc1008_getreg(priv, HDC1008_REG_CONFIGURATION, &reg);
if (ret < 0)
{
return ret;
}
ret = hdc1008_putreg(priv, HDC1008_REG_CONFIGURATION,
reg | HDC1008_CONFIGURATION_RST);
if (ret < 0)
{
return ret;
}
/* Now we wait until the sensor has reset */
do
{
ret = hdc1008_getreg(priv, HDC1008_REG_CONFIGURATION, &reg);
nxsig_usleep(1000);
--count;
}
while ((reg & HDC1008_CONFIGURATION_RST) && (ret == OK) && count);
return ret;
}
/****************************************************************************
* Public Functions
****************************************************************************/
/****************************************************************************
* Name: hdc1008_register
*
* Description:
* Register the HDC1008 character device as 'devpath'
*
* Input Parameters:
* devpath - The full path to the driver to register. E.g., "/dev/temp0"
* i2c - An instance of the I2C interface to use to communicate with
* the HDC1008
* addr - The I2C address of the HDC1008. The I2C address is
* configurable by two address pins, in the range of 0x40-0x43
*
* Returned Value:
* Zero (OK) on success; a negated errno value on failure.
*
****************************************************************************/
int hdc1008_register(FAR const char *devpath, FAR struct i2c_master_s *i2c,
uint8_t addr)
{
FAR struct hdc1008_dev_s *priv;
uint16_t reg;
int ret;
DEBUGASSERT(i2c != NULL);
/* Initialize the driver structure */
priv =
(FAR struct hdc1008_dev_s *)kmm_zalloc(sizeof(struct hdc1008_dev_s));
if (priv == NULL)
{
snerr("ERROR: Failed to allocate memory for driver data\n");
return -ENOMEM;
}
priv->i2c = i2c;
priv->addr = addr;
nxmutex_init(&priv->devlock);
/* Register the driver */
ret = register_driver(devpath, &g_hdc1008fops, 0666, priv);
if (ret < 0)
{
snerr("ERROR: Failed to register driver: %d\n", ret);
nxmutex_destroy(&priv->devlock);
kmm_free(priv);
return ret;
}
sninfo("driver registered\n");
/* 15 ms max startup time according to datasheet, let's wait just to be
* sure that it is ready.
*/
nxsig_usleep(15000);
/* Set default configuration */
ret = hdc1008_getreg(priv, HDC1008_REG_CONFIGURATION, &reg);
if (ret < 0)
{
snerr("ERROR: failed to read default configuration\n");
nxmutex_destroy(&priv->devlock);
kmm_free(priv);
return ret;
}
/* Enforce sensor default configuration at startup */
reg = HDC1008_CONFIGURATION_MODE;
ret = hdc1008_putreg(priv, HDC1008_REG_CONFIGURATION, reg);
if (ret < 0)
{
snerr("ERROR: failed to set default configuration: %d\n", ret);
nxmutex_destroy(&priv->devlock);
kmm_free(priv);
return ret;
}
priv->mode = HDC1008_MEAS_T_AND_RH;
return ret;
}
#endif /* CONFIG_I2C && CONFIG_SENSORS_HDC1008 */
Reference in New Issue View Git Blame Copy Permalink