0f0a94186f
migrate the toolchain define to arch/arm/Kconfig to simplify new toolchain registration Signed-off-by: chao an <anchao@xiaomi.com>
284 lines
10 KiB
Plaintext
284 lines
10 KiB
Plaintext
README
|
|
^^^^^^
|
|
|
|
README file for the Microment Eagle100 NuttX port.
|
|
|
|
References:
|
|
^^^^^^^^^^
|
|
|
|
Micromint: http://www.micromint.com/
|
|
Luminary: http://www.luminarymicro.com/
|
|
|
|
Ethernet-Bootloader
|
|
^^^^^^^^^^^^^^^^^^^
|
|
|
|
Here are some notes about using the Luminary Ethernet boot-loader built
|
|
into the Eagle-100 board.
|
|
|
|
Built-In Application:
|
|
|
|
- The board has no fixed IP address but uses DHCP to get an address.
|
|
I used a D-link router; I can use a web browser to surf to the D-link
|
|
web page to get the address assigned by
|
|
|
|
- Then you can use this IP address in your browser to surf to the Eagle-100
|
|
board. It presents several interesting pages -- the most important is
|
|
the page called "Firmware Update". That page includes instructions on
|
|
how to download code to the Eagle-100.
|
|
|
|
- After you burn the first program, you lose this application. Then you
|
|
will probably be better off connected directly to the Eagle-100 board
|
|
or through a switch (The router caused problems for me during downloads).
|
|
|
|
Using the Ethernet Bootloader:
|
|
|
|
- You will need the "LM Flash Programmer application". You can get that
|
|
program from the Luminary web site. There is a link on the LM3S6918 page.
|
|
|
|
- Is there any documentation for using the bootloader? Yes and No: There
|
|
is an application note covering the bootloader on the Luminary site, but
|
|
it is not very informative. The Eagle100 User's Manual has the best
|
|
information.
|
|
|
|
- Are there any special things I have to do in my code, other than setting
|
|
the origin to 0x0000:2000 (APP_START_ADDRESS)? No. The bootloader assumes
|
|
that you have a vector table at that address . The bootloader does the
|
|
following each time it boots (after you have downloaded the first valid
|
|
application):
|
|
|
|
o The bootloader sets the vector table register to the APP_START_ADDRESS,
|
|
o It sets the stack pointer to the address at APP_START_ADDRESS, and then
|
|
o Jumps to the address at APP_START_ADDRESS+4.
|
|
|
|
- You can force the bootloader to skip starting the application and stay
|
|
in the update mode. You will need to do this in order to download a new
|
|
application. You force the update mode by holding the user button on the
|
|
Eagle-100 board while resetting the board. The user button is GPIOA, pin 6
|
|
(call FORCED_UPDATE_PIN in the bootloader code).
|
|
|
|
- Note 1: I had to remove my D-Link router from the configuration in order
|
|
to use the LM Flash Programmer (the Bootloader issues BOOTP requests to
|
|
communicate with the LM Flash Programmer, my router was responding to
|
|
these BOOTP requests and hosing the download). It is safer to connect
|
|
via a switch or via an Ethernet switch.
|
|
|
|
- Note 2: You don't need the router's DHCPD server in the download
|
|
configuration; the Luminary Flash Programmer has the capability of
|
|
temporarily assigning the IP address to the Eagle-100 via BOOTP.
|
|
|
|
Eagle100-specific Configuration Options
|
|
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
CONFIG_ARCH - Identifies the arch/ subdirectory. This should
|
|
be set to:
|
|
|
|
CONFIG_ARCH=arm
|
|
|
|
CONFIG_ARCH_family - For use in C code:
|
|
|
|
CONFIG_ARCH_ARM=y
|
|
|
|
CONFIG_ARCH_architecture - For use in C code:
|
|
|
|
CONFIG_ARCH_CORTEXM3=y
|
|
|
|
CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
|
|
|
|
CONFIG_ARCH_CHIP=lm
|
|
|
|
CONFIG_ARCH_CHIP_name - For use in C code to identify the exact
|
|
chip:
|
|
|
|
CONFIG_ARCH_CHIP_LM3S6918
|
|
|
|
CONFIG_ARCH_BOARD - Identifies the boards/ subdirectory and
|
|
hence, the board that supports the particular chip or SoC.
|
|
|
|
CONFIG_ARCH_BOARD=eagle100 (for the MicroMint Eagle-100 development board)
|
|
|
|
CONFIG_ARCH_BOARD_name - For use in C code
|
|
|
|
CONFIG_ARCH_BOARD_EAGLE100
|
|
|
|
CONFIG_ARCH_LOOPSPERMSEC - Must be calibrated for correct operation
|
|
of delay loops
|
|
|
|
CONFIG_ENDIAN_BIG - define if big endian (default is little
|
|
endian)
|
|
|
|
CONFIG_RAM_SIZE - Describes the installed DRAM (SRAM in this case):
|
|
|
|
CONFIG_RAM_SIZE=0x00010000 (64Kb)
|
|
|
|
CONFIG_RAM_START - The start address of installed DRAM
|
|
|
|
CONFIG_RAM_START=0x20000000
|
|
|
|
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to boards that
|
|
have LEDs
|
|
|
|
CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
|
|
stack. If defined, this symbol is the size of the interrupt
|
|
stack in bytes. If not defined, the user task stacks will be
|
|
used during interrupt handling.
|
|
|
|
CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
|
|
|
|
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.
|
|
|
|
There are configurations for disabling support for interrupts GPIO ports.
|
|
GPIOH and GPIOJ must be disabled because they do not exist on the LM3S6918.
|
|
Additional interrupt support can be disabled if desired to reduce memory
|
|
footprint.
|
|
|
|
CONFIG_TIVA_GPIOA_IRQS=y
|
|
CONFIG_TIVA_GPIOB_IRQS=y
|
|
CONFIG_TIVA_GPIOC_IRQS=y
|
|
CONFIG_TIVA_GPIOD_IRQS=y
|
|
CONFIG_TIVA_GPIOE_IRQS=y
|
|
CONFIG_TIVA_GPIOF_IRQS=y
|
|
CONFIG_TIVA_GPIOG_IRQS=y
|
|
CONFIG_TIVA_GPIOH_IRQS=n << Always
|
|
CONFIG_TIVA_GPIOJ_IRQS=n << Always
|
|
|
|
LM3S6918 specific device driver settings
|
|
|
|
CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the
|
|
console and ttys0 (default is the UART0).
|
|
CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received.
|
|
This specific the size of the receive buffer
|
|
CONFIG_UARTn_TXBUFSIZE - Characters are buffered before
|
|
being sent. This specific the size of the transmit buffer
|
|
CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be
|
|
CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8.
|
|
CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
|
|
CONFIG_UARTn_2STOP - Two stop bits
|
|
|
|
CONFIG_TIVA_SSI0 - Select to ensable support for SSI0
|
|
CONFIG_TIVA_SSI1 - Select to ensable support for SSI1
|
|
CONFIG_SSI_POLLWAIT - Select to disable interrupt driven SSI support.
|
|
Poll-waiting is recommended if the interrupt rate would be to
|
|
high in the interrupt driven case.
|
|
CONFIG_SSI_TXLIMIT - Write this many words to the Tx FIFO before
|
|
emptying the Rx FIFO. If the SPI frequency is high and this
|
|
value is large, then larger values of this setting may cause
|
|
Rx FIFO overrun errors. Default: half of the Tx FIFO size (4).
|
|
|
|
CONFIG_TIVA_ETHERNET - This must be set (along with CONFIG_NET)
|
|
to build the Stellaris Ethernet driver
|
|
CONFIG_TIVA_ETHLEDS - Enable to use Ethernet LEDs on the board.
|
|
CONFIG_TIVA_BOARDMAC - If the board-specific logic can provide
|
|
a MAC address (via tiva_ethernetmac()), then this should be selected.
|
|
CONFIG_TIVA_ETHHDUPLEX - Set to force half duplex operation
|
|
CONFIG_TIVA_ETHNOAUTOCRC - Set to suppress auto-CRC generation
|
|
CONFIG_TIVA_ETHNOPAD - Set to suppress Tx padding
|
|
CONFIG_TIVA_MULTICAST - Set to enable multicast frames
|
|
CONFIG_TIVA_PROMISCUOUS - Set to enable promiscuous mode
|
|
CONFIG_TIVA_BADCRC - Set to enable bad CRC rejection.
|
|
CONFIG_TIVA_DUMPPACKET - Dump each packet received/sent to the console.
|
|
|
|
Configurations
|
|
^^^^^^^^^^^^^^
|
|
|
|
Common Configuration Notes
|
|
--------------------------
|
|
|
|
1. Each Eagle-100 configuration is maintained in a sub-directory and
|
|
can be selected as follow:
|
|
|
|
tools/configure.sh eagle100:<subdir>
|
|
|
|
Where <subdir> is one of the configuration sub-directories described in
|
|
the following paragraph.
|
|
|
|
2. These configurations use the mconf-based configuration tool. To
|
|
change a configurations using that tool, you should:
|
|
|
|
a. Build and install the kconfig-mconf tool. See nuttx/README.txt
|
|
see additional README.txt files in the NuttX tools repository.
|
|
|
|
b. Execute 'make menuconfig' in nuttx/ in order to start the
|
|
reconfiguration process.
|
|
|
|
Configuration Sub-Directories
|
|
-----------------------------
|
|
|
|
nettest:
|
|
This configuration directory may be used to enable networking using the
|
|
LM3S6918's Ethernet controller. It uses examples/nettest to exercise the
|
|
TCP/IP network.
|
|
|
|
NOTES:
|
|
|
|
1. This configuration is set to use Cygwin under Windows and the ARM
|
|
EABI GCC toolchain. That, however, is easily reconfigurable:
|
|
|
|
CONFIG_HOST_WINDOWS=y
|
|
CONFIG_WINDOWS_CYGWIN=y
|
|
CONFIG_ARM_TOOLCHAIN_GNU_EABI=y
|
|
|
|
httpd:
|
|
This builds the uIP web server example using the examples/webserver application
|
|
(for execution from FLASH).
|
|
|
|
NOTES:
|
|
|
|
1. This configuration is set to use Cygwin under Windows and the ARM
|
|
EABI GCC toolchain. That, however, is easily reconfigurable:
|
|
|
|
CONFIG_HOST_WINDOWS=y
|
|
CONFIG_WINDOWS_CYGWIN=y
|
|
CONFIG_ARM_TOOLCHAIN_GNU_EABI=y
|
|
|
|
This example can only be built using the buildroot toolchain
|
|
with NXFLAT support
|
|
|
|
nsh:
|
|
Configures the NuttShell (nsh) located at examples/nsh. The
|
|
Configuration enables only the serial NSH interfaces (the telnet
|
|
interface should also be functional, but is not enabled in this
|
|
configuration).
|
|
|
|
NOTES:
|
|
|
|
1. This configuration is set to use Cygwin under Windows and the
|
|
devkitARM toolchain. That, however, is easily reconfigurable:
|
|
|
|
CONFIG_HOST_WINDOWS=y
|
|
CONFIG_WINDOWS_CYGWIN=y
|
|
CONFIG_ARM7M_TOOLCHAIN_DEVKITARM=y
|
|
|
|
nxflat:
|
|
This builds the NXFLAT example at apps/examples/nxfalt.
|
|
|
|
NOTES:
|
|
|
|
1. This example can only be built using the NuttX buildroot
|
|
toolchain with the NXFLAT tools.
|
|
|
|
2. This configuration is set to use Cygwin under Windows and the
|
|
devkitARM toolchain. That, however, is easily reconfigurable:
|
|
|
|
CONFIG_HOST_WINDOWS=y
|
|
CONFIG_WINDOWS_CYGWIN=y
|
|
CONFIG_ARM7M_TOOLCHAIN_DEVKITARM=y
|
|
|
|
thttpd:
|
|
This builds the THTTPD web server example using the THTTPD and
|
|
the apps/examples/thttpd application.
|
|
|
|
NOTES:
|
|
|
|
1. This configuration is set to use Linux and the buildroot toolchain.
|
|
That, however, is easily reconfigurable:
|
|
|
|
CONFIG_HOST_LINUX=y
|
|
CONFIG_ARM7M_ARM_TOOLCHAIN_BUILDROOT=y
|
|
|
|
This example can only be built using the buildroot toolchain
|
|
with NXFLAT support
|
|
|
|
By default, all of these examples are built to be used with the Luminary
|
|
Ethernet Bootloader (you can change the ld.script file in any of these
|
|
sub-directories to change that configuration).
|