sergiotarxz/nuttx
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
c0a0de97ce
nuttx/boards/arm/kinetis/freedom-k64f/include/board.h
Alin Jerpelea 40cd67eee6 boards: arm: Author Gregory Nutt: update licenses to Apache 
Gregory Nutt has submitted the SGA and we can migrate the licenses
 to Apache.

Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
2021-03-18 22:58:27 -07:00

299 lines
11 KiB
C
Raw Blame History

/****************************************************************************
* boards/arm/kinetis/freedom-k64f/include/board.h
*
* Licensed to the Apache Software Foundation (ASF) under one or more
* contributor license agreements. See the NOTICE file distributed with
* this work for additional information regarding copyright ownership. The
* ASF licenses this file to you under the Apache License, Version 2.0 (the
* "License"); you may not use this file except in compliance with the
* License. You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
* License for the specific language governing permissions and limitations
* under the License.
*
****************************************************************************/
#ifndef __BOARDS_ARM_KINETIS_FREEDOM_K64F_INCLUDE_BOARD_H
#define __BOARDS_ARM_KINETIS_FREEDOM_K64F_INCLUDE_BOARD_H
/****************************************************************************
* Included Files
****************************************************************************/
#include <nuttx/config.h>
#ifndef __ASSEMBLY__
# include <stdint.h>
#endif
/****************************************************************************
* Pre-processor Definitions
****************************************************************************/
/* Clocking *****************************************************************/
/* The Freedom K64F uses a 50MHz external clock from the Micrel Ethernet PHY.
* The Kinetis MCU startup from an internal digitally-controlled oscillator
* (DCO). NuttX will enable the main external oscillator (EXTAL0/XTAL0).
* The external oscillator/resonator can range from 32.768 KHz up to 50 MHz.
* The default external source for the MCG oscillator inputs (EXTAL) is
* 50 MHz clock source from Micrel Ethernet PHY.
*/
#define BOARD_EXTCLOCK 1 /* External clock */
#define BOARD_EXTAL_FREQ 50000000 /* 50MHz Oscillator from Micrel PHY */
#define BOARD_XTAL32_FREQ 32768 /* 32KHz RTC Oscillator */
/* PLL Configuration. Either the external clock or crystal frequency is used
* to select the PRDIV value.
* Only reference clock frequencies are supported that will produce
* a KINETIS_MCG_PLL_REF_MIN >= PLLIN <= KINETIS_MCG_PLL_REF_MIN reference
* clock to the PLL.
*
* PLL Input frequency: PLLIN = REFCLK / PRDIV = 50 MHz / 20 = 2.5 MHz
* PLL Output frequency: PLLOUT = PLLIN * VDIV = 2.5 MHz * 48 = 120 MHz
* MCG Frequency: PLLOUT = 120 MHz
*
* PRDIV register value is the divider minus KINETIS_MCG_C5_PRDIV_BASE.
* VDIV register value is offset by KINETIS_MCG_C6_VDIV_BASE.
*/
#define BOARD_PRDIV 20 /* PLL External Reference Divider */
#define BOARD_VDIV 48 /* PLL VCO Divider (frequency multiplier) */
#define BOARD_PLLIN_FREQ (BOARD_EXTAL_FREQ / BOARD_PRDIV)
#define BOARD_PLLOUT_FREQ (BOARD_PLLIN_FREQ * BOARD_VDIV)
#define BOARD_MCG_FREQ BOARD_PLLOUT_FREQ
/* Define additional MCG_C2 Setting */
#define BOARD_MCG_C2_FCFTRIM 0 /* Do not enable FCFTRIM */
#define BOARD_MCG_C2_LOCRE0 MCG_C2_LOCRE0 /* Enable reset on loss of clock */
/* SIM CLKDIV1 dividers */
#define BOARD_OUTDIV1 1 /* Core = MCG, 120 MHz */
#define BOARD_OUTDIV2 2 /* Bus = MCG / 2, 60 MHz */
#define BOARD_OUTDIV3 2 /* FlexBus = MCG / 2, 60 MHz */
#define BOARD_OUTDIV4 5 /* Flash clock = MCG / 5, 24 MHz */
#define BOARD_CORECLK_FREQ (BOARD_MCG_FREQ / BOARD_OUTDIV1)
#define BOARD_BUS_FREQ (BOARD_MCG_FREQ / BOARD_OUTDIV2)
#define BOARD_FLEXBUS_FREQ (BOARD_MCG_FREQ / BOARD_OUTDIV3)
#define BOARD_FLASHCLK_FREQ (BOARD_MCG_FREQ / BOARD_OUTDIV4)
/* Use BOARD_MCG_FREQ as the output SIM_SOPT2 MUX selected by
* SIM_SOPT2[PLLFLLSEL]
*/
#define BOARD_SOPT2_PLLFLLSEL SIM_SOPT2_PLLFLLSEL_MCGPLLCLK
#define BOARD_SOPT2_FREQ BOARD_MCG_FREQ
/* Divider output clock = Divider input clock * ((USBFRAC+1) / (USBDIV+1))
* SIM_CLKDIV2_FREQ = BOARD_SOPT2_FREQ * ((USBFRAC+1) / (USBDIV+1))
* SIM_CLKDIV2_FREQ = BOARD_SOPT2_FREQ / (USBDIV+1)* (USBFRAC+1)
* 48MHz = 120MHz / (4 + 1) * (1 + 1)
*/
#if (BOARD_SOPT2_FREQ == 120000000L)
# define BOARD_SIM_CLKDIV2_USBFRAC 2
# define BOARD_SIM_CLKDIV2_USBDIV 5
# define BOARD_SIM_CLKDIV2_FREQ (BOARD_SOPT2_FREQ / \
BOARD_SIM_CLKDIV2_USBDIV * \
BOARD_SIM_CLKDIV2_USBFRAC)
#endif
/* SDHC clocking ************************************************************/
/* SDCLK configurations corresponding to various modes of operation.
* Formula is:
*
* SDCLK frequency = (base clock) / (prescaler * divisor)
*
* The SDHC module is always configure configured so that the core clock is
* the base clock.
* Possible values for presscaler and divisor are:
*
* SDCLKFS: {2, 4, 8, 16, 32, 63, 128, 256}
* DVS: {1..16}
*/
/* Identification mode:
* Optimal 400KHz, Actual 120MHz / (32 * 10) = 375 Khz
*/
#define BOARD_SDHC_IDMODE_PRESCALER SDHC_SYSCTL_SDCLKFS_DIV32
#define BOARD_SDHC_IDMODE_DIVISOR SDHC_SYSCTL_DVS_DIV(10)
/* MMC normal mode:
* Optimal 20MHz, Actual 120MHz / (2 * 3) = 20 MHz
*/
#define BOARD_SDHC_MMCMODE_PRESCALER SDHC_SYSCTL_SDCLKFS_DIV2
#define BOARD_SDHC_MMCMODE_DIVISOR SDHC_SYSCTL_DVS_DIV(3)
/* SD normal mode (1-bit):
* Optimal 20MHz, Actual 120MHz / (2 * 3) = 20 MHz
*/
#define BOARD_SDHC_SD1MODE_PRESCALER SDHC_SYSCTL_SDCLKFS_DIV2
#define BOARD_SDHC_SD1MODE_DIVISOR SDHC_SYSCTL_DVS_DIV(3)
/* SD normal mode (4-bit):
* Optimal 25MHz, Actual 120MHz / (2 * 3) = 20 MHz (with DMA)
* SD normal mode (4-bit):
* Optimal 20MHz, Actual 120MHz / (2 * 3) = 20 MHz (no DMA)
*/
#ifdef CONFIG_SDIO_DMA
# define BOARD_SDHC_SD4MODE_PRESCALER SDHC_SYSCTL_SDCLKFS_DIV2
# define BOARD_SDHC_SD4MODE_DIVISOR SDHC_SYSCTL_DVS_DIV(3)
#else
# define BOARD_SDHC_SD4MODE_PRESCALER SDHC_SYSCTL_SDCLKFS_DIV2
# define BOARD_SDHC_SD4MODE_DIVISOR SDHC_SYSCTL_DVS_DIV(3)
#endif
/* Use the output of SIM_SOPT2[PLLFLLSEL] as the USB clock source */
#define BOARD_USB_CLKSRC SIM_SOPT2_USBSRC
#define BOARD_USB_FREQ BOARD_SIM_CLKDIV2_FREQ
/* Allow USBOTG-FS Controller to Read from FLASH */
#define BOARD_USB_FLASHACCESS
/* PWM Configuration */
/* FTM0 Channels */
/* Channels can be modified using kinetis_k64pinmux.h */
#define GPIO_FTM0_CH0OUT PIN_FTM0_CH0_1
#define GPIO_FTM0_CH1OUT PIN_FTM0_CH1_1
#define GPIO_FTM0_CH2OUT PIN_FTM0_CH2_2
#define GPIO_FTM0_CH3OUT PIN_FTM0_CH3_1
#define GPIO_FTM0_CH4OUT PIN_FTM0_CH4_1
#define GPIO_FTM0_CH5OUT PIN_FTM0_CH5_1
/* LED definitions **********************************************************/
/* The Freedom K64F has a single RGB LED driven by the K64F as follows:
*
* LED K64
* ------ -------------------------------------------------------
* RED PTB22/SPI2_SOUT/FB_AD29/CMP2_OUT
* BLUE PTB21/SPI2_SCK/FB_AD30/CMP1_OUT
* GREEN PTE26/ENET_1588_CLKIN/UART4_CTS_b/RTC_CLKOUT/USB0_CLKIN
*
* If CONFIG_ARCH_LEDS is not defined, then the user can control the LEDs
* in any way.
* The following definitions are used to access individual LEDs.
*/
/* LED index values for use with board_userled() */
#define BOARD_LED_R 0
#define BOARD_LED_G 1
#define BOARD_LED_B 2
#define BOARD_NLEDS 3
/* LED bits for use with board_userled_all() */
#define BOARD_LED_R_BIT (1 << BOARD_LED_R)
#define BOARD_LED_G_BIT (1 << BOARD_LED_G)
#define BOARD_LED_B_BIT (1 << BOARD_LED_B)
/* If CONFIG_ARCH_LEDs is defined, then NuttX will control the LED on board
* the Freedom K64F. The following definitions describe how NuttX controls
* the LEDs:
*
* SYMBOL Meaning LED state
* RED GREEN BLUE
* ------------------- ---------------------------- -----------------
*/
#define LED_STARTED 1 /* NuttX has been started OFF OFF OFF */
#define LED_HEAPALLOCATE 2 /* Heap has been allocated OFF OFF ON */
#define LED_IRQSENABLED 0 /* Interrupts enabled OFF OFF ON */
#define LED_STACKCREATED 3 /* Idle stack created OFF ON OFF */
#define LED_INIRQ 0 /* In an interrupt (no change) */
#define LED_SIGNAL 0 /* In a signal handler (no change) */
#define LED_ASSERTION 0 /* An assertion failed (no change) */
#define LED_PANIC 4 /* The system has crashed FLASH OFF OFF */
#undef LED_IDLE /* K64 is in sleep mode (Not used) */
/* Button definitions *******************************************************/
/* Two push buttons, SW2 and SW3, are available on FRDM-K64F board,
* where SW2 is connected to PTC6 and SW3 is connected to PTA4.
* Besides the general purpose input/output functions, SW2 and SW3 can be
* low-power wake up signal. Also, only SW3 can be a non-maskable interrupt.
*
* Switch GPIO Function
* ------- ---------------------------------------------------------------
* SW2 PTC6/SPI0_SOUT/PD0_EXTRG/I2S0_RX_BCLK/FB_AD9/I2S0_MCLK/LLWU_P10
* SW3 PTA4/FTM0_CH1/NMI_b/LLWU_P3
*/
#define BUTTON_SW2 0
#define BUTTON_SW3 1
#define NUM_BUTTONS 2
#define BUTTON_SW2_BIT (1 << BUTTON_SW2)
#define BUTTON_SW3_BIT (1 << BUTTON_SW3)
/* Alternative pin resolution ***********************************************/
/* If there are alternative configurations for various pins in the
* kinetis_k64pinmux.h header file, those alternative pins will be labeled
* with a suffix like _1, _2, etc. The logic in this file must select the
* correct pin configuration for the board by defining a pin configuration
* (with no suffix) that maps to the correct alternative.
*/
/* The primary serial port interface signals are PTB16 UART0_RX and
* PTB17 UART0_TX.
* These signals are connected to the OpenSDAv2 circuit.
*/
#define PIN_UART0_RX PIN_UART0_RX_3
#define PIN_UART0_TX PIN_UART0_TX_3
/* An alternative serial port might use a standard serial shield mounted
* on the Freedom Board. In this case, Arduino pin D1 provides UART TX and
* pin D0 provides UART RX.
*
* The I/O headers on the FRDM-K64F board are arranged to enable
* compatibility with Arduino shield. The outer rows of pins (even numbered
* pins) on the headers, share the same mechanical spacing and placement with
* the I/O headers on the Arduino Revision 3 (R3) standard.
*
* The Arduino D0 and D1 pins then correspond to pins 2 and 4 on the J1 I/O
* connector:
*
* Arduino Pin FRDM-K64F J1 Connector
* ------------------------ -----------------------
* UART TX, Arduino D1 pin Pin 4, PTC17, UART3_TX
* UART RX, Arduino D0 pin Pin 2, PTC16, UART3_RX
*/
#define PIN_UART3_RX PIN_UART3_RX_2
#define PIN_UART3_TX PIN_UART3_TX_2
/* I2C Bus 0
*
* Pin Name K64 Name
* ---- ----- ------ ---------
* 11 SCL PTE24 2C0_SCL
* 12 SDA PTE25 2C0_SDA
*/
#define PIN_I2C0_SCL PIN_I2C0_SCL_4
#define PIN_I2C0_SDA PIN_I2C0_SDA_4
#endif /* __BOARDS_ARM_FREEDOM_K64F_INCLUDE_BOARD_H */
Reference in New Issue View Git Blame Copy Permalink