nuttx/boards/arm/s32k1xx/s32k146evb
2019-08-19 13:07:45 -06:00
..
configs/nsh This commit adds support for the S32K146EVB 2019-08-19 09:14:14 -06:00
include This commit adds support for the S32K146EVB 2019-08-19 09:14:14 -06:00
scripts This commit adds support for the S32K146EVB 2019-08-19 09:14:14 -06:00
src arch/arm/src/s32k1xx/s32k1xx_clockconfig.c and related files: Fix confusion about who decrements the rster value. Some dividers may have a function range of 1..8 but the register value is 0..7. There were several places where values were getting decremented twice: Once by higher up logic and once by the register access logic. A such dividers were reviewed and, hopefully, all were fixed. 2019-08-19 13:07:45 -06:00
Kconfig This commit adds support for the S32K146EVB 2019-08-19 09:14:14 -06:00
README.txt arch/arm/src/s32k1xx/s32k14x and boards/arm/s32k1xx/s32k146evb/src: Numerous fixes to get a clean build of the S32K146EVB. 2019-08-19 10:49:50 -06:00

README
======

This directory hold the port to the NXP S32K146EVB-Q144 Development board.

Contents
========

  o Status
  o Serial Console
  o LEDs and Buttons
  o Configurations

Status
======

  2019-08-148  Configuration created but entirely untested.  This
    configuration is intended, initially, to verify s32k14x architecture
    support.  The configuration builds and linkes without error but has
    not yet been tested.  This is VERY much a work in progress and you
    should not use this configuration unless you are interested in
    assisting with the bring-up.

Serial Console
==============

  By default, the serial console will be provided on the OpenSDA VCOM port:

    OpenSDA UART TX  PTC7 (LPUART1_TX)
    OpenSDA UART RX  PTC6 (LPUART1_RX)

LEDs and Buttons
================

  LEDs
  ----
  The S32K146EVB has one RGB LED:

    RedLED   PTD15 (FTM0 CH0)
    GreenLED PTD16 (FTM0 CH1)
    BlueLED  PTD0  (FTM0 CH2)

  If CONFIG_ARCH_LEDS is not defined, then the user can control the LEDs in
  any way.  The following definitions are used to access individual RGB
  components.

  The RGB components could, alternatively be controlled through PWM using
  the common RGB LED driver.

  If CONFIG_ARCH_LEDs is defined, then NuttX will control the LEDs on board
  the s32k146evb.  The following definitions describe how NuttX controls the
  LEDs:

    ==========================================+========+========+=========
                                                 RED     GREEN     BLUE
    ==========================================+========+========+=========

    LED_STARTED      NuttX has been started      OFF      OFF      OFF
    LED_HEAPALLOCATE Heap has been allocated     OFF      OFF      ON
    LED_IRQSENABLED  Interrupts enabled          OFF      OFF      ON
    LED_STACKCREATED Idle stack created          OFF      ON       OFF
    LED_INIRQ        In an interrupt                   (no change)
    LED_SIGNAL       In a signal handler               (no change)
    LED_ASSERTION    An assertion failed               (no change)
    LED_PANIC        The system has crashed      FLASH    OFF      OFF
    LED_IDLE         S32K146EVN in sleep mode          (no change)
    ==========================================+========+========+=========

  Buttons
  -------
  The S32K146EVB supports two buttons:

    SW2  PTC12
    SW3  PTC13

Configurations
==============

  Common Information
  ------------------
  Each S32K146EVB configuration is maintained in a sub-directory and
  can be selected as follow:

    tools/configure.sh s32k146evb:<subdir>

  Where <subdir> is one of the sub-directories listed in the next paragraph

    NOTES (common for all configurations):

    1. This configuration uses the mconf-based configuration tool.  To
       change this configuration using that tool, you should:

       a. Build and install the kconfig-mconf tool.  See nuttx/README.txt
          see additional README.txt files in the NuttX tools repository.

       b. Execute 'make menuconfig' in nuttx/ in order to start the
          reconfiguration process.

    2. Unless otherwise stated, the serial console used is LPUART1 at
       115,200 8N1.  This corresponds to the OpenSDA VCOM port.

  Configuration Sub-directories
  -------------------------

    nsh:
    ---
      Configures the NuttShell (nsh) located at apps/examples/nsh.  Support
      for builtin applications is enabled, but in the base configuration no
      builtin applications are selected.