nuttx/boards/arm64/rk3399/pinephonepro/include/board.h
Anner J. Bonilla 24e45d071e Pinephone Pro port just nsh
Pinephone Pro port just nsh

Status:
booting till GICD / IRQ issue

style cleanups

start to fix style checks

revert offset

whitespaces

revert a64 bringup file

prob last cleanup

more cleanups

remove dts

move changes from a64 hardware specific folders to rk3399

undo common changes (except head.s)

revert gitignore

missing irq.h and rk3399_serial.c need to finish cleaning them up

WIP

add source for load address

make debug print hex again add board include

Pinephone Pro port just nsh

Status:
booting till GICD / IRQ issue

style cleanups

start to fix style checks

revert offset

whitespaces

revert a64 bringup file

prob last cleanup

more cleanups

remove dts

move changes from a64 hardware specific folders to rk3399

undo common changes (except head.s)

revert gitignore

missing irq.h and rk3399_serial.c need to finish cleaning them up

WIP

add source for load address

remove ccache, add board memory map

remove board reset
2023-08-24 11:16:31 +08:00

72 lines
3.1 KiB
C

/****************************************************************************
* boards/arm64/rk3399/pinephonepro/include/board.h
*
* Licensed to the Apache Software Foundation (ASF) under one or more
* contributor license agreements. See the NOTICE file distributed with
* this work for additional information regarding copyright ownership. The
* ASF licenses this file to you under the Apache License, Version 2.0 (the
* "License"); you may not use this file except in compliance with the
* License. You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
* License for the specific language governing permissions and limitations
* under the License.
*
****************************************************************************/
#ifndef __BOARDS_ARM64_RK3399_PINEPHONE_PRO_INCLUDE_BOARD_H
#define __BOARDS_ARM64_RK3399_PINEPHONE_PRO_INCLUDE_BOARD_H
/****************************************************************************
* Included Files
****************************************************************************/
#include <nuttx/config.h>
/****************************************************************************
* Pre-processor Definitions
****************************************************************************/
/* LED definitions **********************************************************/
/* LED index values for use with board_userled() */
typedef enum
{
BOARD_LED1 = 0, /* Green LED */
BOARD_LED2 = 1, /* Red LED */
BOARD_LED3 = 2, /* Blue LED */
BOARD_LEDS /* Number of LEDs */
} led_typedef_enum;
/* LED bits for use with board_userled_all() */
#define BOARD_LED1_BIT (1 << BOARD_LED1)
#define BOARD_LED2_BIT (1 << BOARD_LED2)
#define BOARD_LED3_BIT (1 << BOARD_LED3)
/* If CONFIG_ARCH_LEDS is defined, the usage by the board port is defined in
* include/board.h and src/pinephone_autoleds.c. The LEDs are used to encode
* OS-related events as follows:
*
* SYMBOL Meaning LED state
* LED1 LED2 LED3
* ---------------------- -------------------------- ------ ------ ---
*/
#define LED_STARTED 0 /* NuttX has been started OFF OFF OFF */
#define LED_HEAPALLOCATE 1 /* Heap has been allocated ON OFF OFF */
#define LED_IRQSENABLED 2 /* Interrupts enabled OFF ON OFF */
#define LED_STACKCREATED 3 /* Idle stack created OFF OFF ON */
#define LED_INIRQ 4 /* In an interrupt ON ON OFF */
#define LED_SIGNAL 5 /* In a signal handler ON OFF ON */
#define LED_ASSERTION 6 /* An assertion failed OFF ON ON */
#define LED_PANIC 7 /* The system has crashed FLASH ON ON */
#define LED_IDLE 8 /* MCU is is sleep mode OFF FLASH OFF */
#endif /* __BOARDS_ARM64_RK3399_PINEPHONE_PRO_INCLUDE_BOARD_H */