56529d2944
- migrated /README are removed from /boards - there are a lot of READMEs that should be further converted to rst. At the moment they are moved to Documentation/platforms and included in rst files
95 lines
1.6 KiB
Plaintext
95 lines
1.6 KiB
Plaintext
README
|
|
======
|
|
|
|
This README discusses issues unique to NuttX configurations for the
|
|
AT32F437-MINI development board featuring the AT32F437VMT7
|
|
MCU. The AT32F437VMT7 is a 288MHz Cortex-M4 operation with 4Mbyte Flash
|
|
memory and 384kbytes.
|
|
|
|
|
|
LEDs
|
|
====
|
|
LED1 = PE2
|
|
LED2 = PE3
|
|
|
|
USART/UART
|
|
====
|
|
USART1
|
|
RX = PA10
|
|
TX = PA9
|
|
The usart1 is used for console.
|
|
./tools/configure.sh at32f437-mini/nsh
|
|
make -j16 and flash nuttx.hex,then run it will show:
|
|
NuttShell (NSH) NuttX-12.2.1
|
|
nsh>
|
|
nsh>
|
|
nsh> ps
|
|
PID GROUP PRI POLICY TYPE NPX STATE EVENT SIGMASK STACK COMMAND
|
|
0 0 0 FIFO Kthread N-- Ready 0000000000000000 001016 Idle_Task
|
|
2 2 100 RR Task --- Running 0000000000000000 002016 nsh_main
|
|
nsh>
|
|
|
|
USART2/RS485
|
|
RX = PD6
|
|
TX = PD5
|
|
DIR = PD4
|
|
|
|
CAN
|
|
====
|
|
CAN1
|
|
TX = PD1
|
|
RX = PD0
|
|
CAN_CHARDRIVER: ./tools/configure.sh at32f437-mini/can_char
|
|
CAN_SOCKET: ./tools/configure.sh at32f437-mini/can_socket
|
|
|
|
USB
|
|
====
|
|
OTGFS1
|
|
D+ = PA12
|
|
D- = PA11
|
|
|
|
SDIO
|
|
====
|
|
SDIO1
|
|
CMD = PD2
|
|
CLK = PC12
|
|
D0 = PC8
|
|
D1 = PC9
|
|
D2 = PC10
|
|
D3 = PC11
|
|
|
|
ETH
|
|
RMII_REF_CLK = PA1
|
|
ETH_MDIO = PA2
|
|
RMII_CRS_DV = PA7
|
|
ETH_MDC = PC1
|
|
RMII_RXD0 = PC4
|
|
RMII_RXD1 = PC5
|
|
RMII_TX_EN = PB11
|
|
RMII_TXD0 = PB12
|
|
RMII_TXD1 = PB13
|
|
ETH_RST = PA3
|
|
The eth used lan8720a as phy
|
|
|
|
|
|
W25QXX
|
|
CLK = PB3
|
|
MISO = PB4
|
|
MOSI = PB5
|
|
CS = PD7
|
|
|
|
RTC
|
|
The board used rtc device on chip
|
|
|
|
PWM
|
|
The pwm test with tim20 chanel1 in PE2
|
|
|
|
ADC
|
|
ADC1 chanel8(PB0)
|
|
|
|
|
|
|
|
|
|
|
|
|