1968 lines
49 KiB
Plaintext
1968 lines
49 KiB
Plaintext
#
|
|
# For a description of the syntax of this configuration file,
|
|
# see the file kconfig-language.txt in the NuttX tools repository.
|
|
#
|
|
|
|
menuconfig USBDEV
|
|
bool "USB Device Driver Support"
|
|
default n
|
|
---help---
|
|
USB device drivers. See also include/nuttx/usb/usbdev.h
|
|
|
|
if USBDEV
|
|
|
|
comment "USB Device Controller Driver Options"
|
|
|
|
config USBDEV_ISOCHRONOUS
|
|
bool "Enable isochronous"
|
|
default n
|
|
---help---
|
|
Build in extra support for isochronous endpoints
|
|
|
|
config USBDEV_DUALSPEED
|
|
bool "Enable high and full speed"
|
|
default n
|
|
---help---
|
|
Hardware handles high and full speed operation (USB 2.0)
|
|
|
|
config USBDEV_SUPERSPEED
|
|
bool "Enable super speed"
|
|
default n
|
|
---help---
|
|
Hardware handles super speed operation (USB 3.2)
|
|
|
|
config USBDEV_EPBUFFER_ALIGNMENT
|
|
int "The usbdev ep req bffer aligned bytes"
|
|
default 0
|
|
---help---
|
|
The aligned bytes of usbdev ep req buffer
|
|
|
|
choice
|
|
prompt "Select USB device powered"
|
|
default USBDEV_SELFPOWERED
|
|
|
|
config USBDEV_SELFPOWERED
|
|
bool "Self powered"
|
|
---help---
|
|
Will cause USB features to indicate that the device is self-powered
|
|
|
|
config USBDEV_BUSPOWERED
|
|
bool "Bus powered"
|
|
---help---
|
|
Will cause USB features to indicate that the device is not self-powered
|
|
|
|
endchoice # Select USB device powered
|
|
|
|
config USBDEV_MAXPOWER
|
|
int "Maximum power consumption in mA"
|
|
default 100
|
|
# depends on USBDEV_BUSPOWERED
|
|
---help---
|
|
Maximum power consumption in mA. This selection should only apply if
|
|
the device is bus powered (USBDEV_BUSPOWERED). It is, however, used
|
|
unconditionally in several USB device drivers.
|
|
|
|
config USBDEV_SOFINTERRUPT
|
|
bool "Enable USB device SOF interrupts"
|
|
default n
|
|
---help---
|
|
Enable USB start-of-frame interrupts.
|
|
Can be used for synchronizing to host clock rate.
|
|
Board logic must provide usbdev_sof_irq() function.
|
|
|
|
config USBDEV_DMA
|
|
bool "Enable DMA methods"
|
|
default n
|
|
---help---
|
|
Select this enable DMA-related methods in USB device controller driver
|
|
interface. These methods include the DMA buffer allocation methods:
|
|
allobuffer() and freebuffer().
|
|
|
|
The USB class driver allocates packet I/O buffers for data transfer by
|
|
calling the driver allocbuffer() and freebuffer() methods. Those methods
|
|
are only available if USBDEV_DMA is defined in the system configuration.
|
|
|
|
config USBDEV_DMAMEMORY
|
|
bool "Board DMA Allocation Hooks"
|
|
default n
|
|
depends on USBDEV_DMA
|
|
---help---
|
|
The USB class driver allocates packet I/O buffers for data transfer by
|
|
calling the driver allocbuffer() and freebuffer() methods. Those methods
|
|
are only available if USBDEV_DMA is defined in the system configuration.
|
|
|
|
If USBDEV_DMAMEMORY is also defined in the NuttX configuration, then
|
|
the driver implementations of the allocbuffer() and freebuffer()
|
|
methods may use board-specific usbdev_dma_alloc() and usbdev_dma_free().
|
|
If USBDEV_DMA and USBDEV_DMAMEMORY are both defined, then the board-
|
|
specific logic must provide the functions usbdev_dma_alloc() and
|
|
usbdev_dma_free(): usbdev_dma_alloc() will allocate DMA-capable
|
|
memory of the specified size; usbdev_dma_free() is the corresponding
|
|
function that will be called to free the DMA-capable memory.
|
|
|
|
config ARCH_USBDEV_STALLQUEUE
|
|
bool
|
|
default n
|
|
---help---
|
|
This option is set by the USB device controller driver (DCD)
|
|
selection. These selection means that the DCD can support
|
|
queuing of stall requests. By this, it is meant that, (1) the
|
|
stall is not sent until all write requests preceding the stall
|
|
request are sent, (2) the stall is sent, and then after the
|
|
stall is cleared, (3) all write requests queued after the stall
|
|
are sent.
|
|
|
|
If the driver does not support this feature, that the class drivers
|
|
will enable some hokey and inefficient delay logic to workaround
|
|
the lack of queuing.
|
|
|
|
menuconfig USBDEV_TRACE
|
|
bool "Enable USB tracing for debug"
|
|
default n
|
|
select HAVE_USBTRACE
|
|
---help---
|
|
Enables USB tracing for debug
|
|
|
|
if USBDEV_TRACE
|
|
|
|
config USBDEV_TRACE_NRECORDS
|
|
int "Number of trace entries to remember"
|
|
default 128
|
|
---help---
|
|
Number of trace entries to remember
|
|
|
|
config USBDEV_TRACE_STRINGS
|
|
bool "Decode device controller events"
|
|
default n
|
|
depends on DEBUG_USB
|
|
---help---
|
|
If USBDEV_TRACE_STRINGS is defined, then the USB device controller
|
|
driver must provide arrays of strings to support decoding of device-
|
|
specific trace events. These arrays of strings (and the type struct
|
|
trace_msg_t) are defined in include/nuttx/usb/usbdev_trace.h:
|
|
|
|
#ifdef CONFIG_USBDEV_TRACE_STRINGS
|
|
extern const struct trace_msg_t g_usb_trace_strings_deverror[];
|
|
extern const struct trace_msg_t g_usb_trace_strings_intdecode[];
|
|
#endif
|
|
|
|
endif # USBDEV_TRACE
|
|
|
|
config USBDEV_TRACE_INITIALIDSET
|
|
int "Initial enable bits"
|
|
default 0
|
|
---help---
|
|
This is the set of initial USB features that are enabled at boot
|
|
time. See the event ID class bit definitions in
|
|
include/nuttx/usbdev_trace.h.
|
|
|
|
menuconfig USBDEV_CUSTOM_TXFIFO_SIZE
|
|
bool "Custom TX Fifo size"
|
|
default n
|
|
---help---
|
|
Enables custom TX Fifo size
|
|
|
|
if USBDEV_CUSTOM_TXFIFO_SIZE
|
|
|
|
config USBDEV_EP0_TXFIFO_SIZE
|
|
int "USBDEV_EP0_TXFIFO_SIZE"
|
|
default 64
|
|
|
|
config USBDEV_EP1_TXFIFO_SIZE
|
|
int "USBDEV_EP1_TXFIFO_SIZE"
|
|
default 0
|
|
|
|
config USBDEV_EP2_TXFIFO_SIZE
|
|
int "USBDEV_EP2_TXFIFO_SIZE"
|
|
default 0
|
|
|
|
config USBDEV_EP3_TXFIFO_SIZE
|
|
int "USBDEV_EP3_TXFIFO_SIZE"
|
|
default 0
|
|
|
|
config USBDEV_EP4_TXFIFO_SIZE
|
|
int "USBDEV_EP4_TXFIFO_SIZE"
|
|
default 0
|
|
|
|
config USBDEV_EP5_TXFIFO_SIZE
|
|
int "USBDEV_EP5_TXFIFO_SIZE"
|
|
default 0
|
|
|
|
config USBDEV_EP6_TXFIFO_SIZE
|
|
int "USBDEV_EP6_TXFIFO_SIZE"
|
|
default 0
|
|
|
|
config USBDEV_EP7_TXFIFO_SIZE
|
|
int "USBDEV_EP7_TXFIFO_SIZE"
|
|
default 0
|
|
|
|
config USBDEV_EP8_TXFIFO_SIZE
|
|
int "USBDEV_EP8_TXFIFO_SIZE"
|
|
default 0
|
|
|
|
endif # USBDEV_CUSTOM_TXFIFO_SIZE
|
|
|
|
comment "USB Device Class Driver Options"
|
|
|
|
menuconfig USBDEV_COMPOSITE
|
|
bool "USB composite device support"
|
|
default n
|
|
---help---
|
|
Enables USB composite device support
|
|
|
|
if USBDEV_COMPOSITE
|
|
|
|
config COMPOSITE_IAD
|
|
bool "Use Interface Associate Descriptor (IAD)"
|
|
default n
|
|
---help---
|
|
If one of the members of the composite has multiple interfaces
|
|
(such as CDC/ACM), then an Interface Association Descriptor (IAD)
|
|
will be necessary. Default: IAD will be used automatically if
|
|
needed. It should not be necessary to set this.
|
|
|
|
config COMPOSITE_EP0MAXPACKET
|
|
int "Max packet size for endpoint 0"
|
|
default 64
|
|
---help---
|
|
Max packet size for endpoint 0
|
|
|
|
config COMPOSITE_VENDORID
|
|
hex "Composite vendor ID"
|
|
default 0x0000
|
|
|
|
config COMPOSITE_VENDORSTR
|
|
string "Composite vendor ID"
|
|
default "NuttX"
|
|
---help---
|
|
The vendor ID code/string
|
|
|
|
config COMPOSITE_PRODUCTID
|
|
hex "Composite product id"
|
|
default 0x0000
|
|
|
|
config COMPOSITE_PRODUCTSTR
|
|
string "Composite product string"
|
|
default "Composite device"
|
|
---help---
|
|
The product ID code/string
|
|
|
|
config COMPOSITE_SERIALSTR
|
|
string "Composite serial string"
|
|
default "001"
|
|
depends on !BOARD_USBDEV_SERIALSTR
|
|
---help---
|
|
Device serial number string
|
|
|
|
config COMPOSITE_CONFIGSTR
|
|
string "Configuration string"
|
|
default "NuttX COMPOSITE config"
|
|
---help---
|
|
Configuration string
|
|
|
|
config COMPOSITE_VERSIONNO
|
|
hex "Composite version number"
|
|
default 0x1010
|
|
---help---
|
|
Interface version number.
|
|
|
|
config COMPOSITE_MSFT_OS_DESCRIPTORS
|
|
bool "Add support for Microsoft OS Descriptors"
|
|
default n
|
|
---help---
|
|
Microsoft Windows cannot always automatically determine appropriate
|
|
drivers for different interfaces of a USB composite device. There is
|
|
a vendor-specific mechanism called "Microsoft OS Descriptors" that
|
|
allows the interface to provide further ID code to help with driver
|
|
loading. See https://msdn.microsoft.com/en-us/windows/hardware/gg463179
|
|
Enabling this feature in composite driver will pass these requests
|
|
onwards to the interface drivers.
|
|
|
|
config COMPOSITE_DEVICES
|
|
int "Max class object for composite device"
|
|
default 8
|
|
---help---
|
|
Composite device class object number.
|
|
|
|
endif # USBDEV_COMPOSITE
|
|
|
|
config PL2303
|
|
bool "Prolific PL2303 serial/USB converter emulation"
|
|
default n
|
|
select SERIAL_REMOVABLE
|
|
---help---
|
|
This logic emulates the Prolific PL2303 serial/USB converter
|
|
|
|
if PL2303
|
|
|
|
config PL2303_CONSOLE
|
|
bool "PL2303 console device"
|
|
default n
|
|
---help---
|
|
Register the USB device as /dev/console so that is will be used
|
|
as the console device.
|
|
|
|
config PL2303_EPINTIN
|
|
int "Interrupt IN endpoint number"
|
|
default 1
|
|
|
|
config PL2303_EPBULKOUT
|
|
int "Bulk OUT endpoint number"
|
|
default 2
|
|
|
|
config PL2303_EPBULKIN
|
|
int "Bulk IN endpoint number"
|
|
default 3
|
|
|
|
config PL2303_EP0MAXPACKET
|
|
int "Packet and request buffer sizes"
|
|
default 64
|
|
|
|
config PL2303_EPBULK_FSSIZE
|
|
int "BULK endpoints full speed MAXPACKET size"
|
|
default 64
|
|
---help---
|
|
Max package size for the bulk endpoint if full speed mode.
|
|
Default 64.
|
|
|
|
if USBDEV_DUALSPEED
|
|
|
|
config PL2303_EPBULK_HSSIZE
|
|
int "BULK endpoints high speed MAXPACKET size"
|
|
default 512
|
|
---help---
|
|
Max package size for the bulk endpoint if high speed mode.
|
|
Default 512.
|
|
|
|
endif # USBDEV_DUALSPEED
|
|
|
|
if USBDEV_SUPERSPEED
|
|
|
|
config PL2303_EPBULK_SSSIZE
|
|
int "BULK endpoints super speed MAXPACKET size"
|
|
default 1024
|
|
---help---
|
|
Max package size for the bulk endpoint if super speed mode.
|
|
Default 1024.
|
|
|
|
config PL2303_EPBULK_MAXBURST
|
|
int "BULK endpoints super speed MAXBURST size"
|
|
default 0
|
|
---help---
|
|
Max burst size for the bulk endpoint if super speed mode.
|
|
Default 0.
|
|
|
|
config PL2303_EPBULK_MAXSTREAM
|
|
int "BULK endpoints super speed MAXSTREAM size"
|
|
default 0
|
|
---help---
|
|
Max stream size for the bulk endpoint if super speed mode.
|
|
Default 0.
|
|
|
|
endif # USBDEV_SUPERSPEED
|
|
|
|
config PL2303_NWRREQS
|
|
int "Number of read requests that can be in flight"
|
|
default 4
|
|
---help---
|
|
The number of read requests that can be in flight
|
|
|
|
config PL2303_NRDREQS
|
|
int "Number of write requests that can be in flight"
|
|
default 4
|
|
---help---
|
|
The number of write/read requests that can be in flight
|
|
|
|
config PL2303_BULKIN_REQLEN
|
|
int "Size of one write request buffer"
|
|
default 768 if USBDEV_DUALSPEED
|
|
default 96 if !USBDEV_DUALSPEED
|
|
---help---
|
|
Ideally, the BULKOUT request size should *not* be the same size as
|
|
the maxpacket size. That is because IN transfers of exactly the
|
|
maxpacket size will be followed by a NULL packet. The BULKOUT,
|
|
on the other hand, request buffer size is always the same as the
|
|
maxpacket size.
|
|
|
|
There is also no reason from PL2303_BULKIN_REQLEN to be greater
|
|
than PL2303_TXBUFSIZE-1, since a request larger than the TX
|
|
buffer can never be sent.
|
|
|
|
config PL2303_RXBUFSIZE
|
|
int "Receive buffer size"
|
|
default 513 if USBDEV_DUALSPEED
|
|
default 257 if !USBDEV_DUALSPEED
|
|
---help---
|
|
Size of the serial receive buffers. The actual amount of data that
|
|
can be held in the buffer is this number minus one due to the way
|
|
that the circular buffer is managed. So an RX buffer size of 257
|
|
will hold four full-speed, 64 byte packets; a buffer size of 513
|
|
will hold one high-speed, 512 byte packet.
|
|
|
|
config PL2303_TXBUFSIZE
|
|
int "Transmit buffer size"
|
|
default 769 if USBDEV_DUALSPEED
|
|
default 193 if !USBDEV_DUALSPEED
|
|
---help---
|
|
Size of the serial transmit buffers. The actual amount of data that
|
|
can be held in the buffer is this number minus one due to the way
|
|
that the circular buffer is managed. So a TX buffer size of 769
|
|
will hold one request of size 768; a buffer size of 193 will hold
|
|
two requests of size 96 bytes.
|
|
|
|
config PL2303_VENDORID
|
|
hex "Vendor ID"
|
|
default 0x067b
|
|
|
|
config PL2303_PRODUCTID
|
|
hex "Product ID"
|
|
default 0x2303
|
|
|
|
config PL2303_VENDORSTR
|
|
string "Vendor string"
|
|
default "NuttX"
|
|
|
|
config PL2303_PRODUCTSTR
|
|
string "Product string"
|
|
default "PL2303 Emulation"
|
|
|
|
endif # PL2303
|
|
|
|
menuconfig CDCACM
|
|
bool "USB Modem (CDC/ACM) support"
|
|
default n
|
|
select SERIAL_REMOVABLE
|
|
---help---
|
|
Enables USB Modem (CDC/ACM) support
|
|
|
|
if CDCACM
|
|
|
|
config CDCACM_CONSOLE
|
|
bool "CDC/ACM console device"
|
|
default n
|
|
---help---
|
|
Register the USB device as /dev/console so that is will be used
|
|
as the console device.
|
|
|
|
config CDCACM_IFLOWCONTROL
|
|
bool "CDC/ACM RTS flow control"
|
|
default n
|
|
select SERIAL_IFLOWCONTROL
|
|
---help---
|
|
Enable CDC/ACM RTS flow control
|
|
|
|
config CDCACM_OFLOWCONTROL
|
|
bool "CDC/ACM CTS flow control"
|
|
default n
|
|
depends on EXPERIMENTAL
|
|
select SERIAL_OFLOWCONTROL
|
|
---help---
|
|
Enable CDC/ACM CTS flow control
|
|
|
|
menuconfig CDCACM_COMPOSITE
|
|
bool "CDC/ACM composite support"
|
|
default n
|
|
depends on USBDEV_COMPOSITE
|
|
---help---
|
|
Configure the CDC serial driver as part of a composite driver
|
|
(only if USBDEV_COMPOSITE is also defined)
|
|
|
|
if !CDCACM_COMPOSITE
|
|
|
|
# In a composite device the EP0 config comes from the composite device
|
|
# and the EP-Number is configured dynamically via composite_initialize
|
|
|
|
config CDCACM_EP0MAXPACKET
|
|
int "Endpoint 0 max packet size"
|
|
default 64
|
|
---help---
|
|
Endpoint 0 max packet size. Default 64.
|
|
|
|
config CDCACM_EPINTIN
|
|
int "Interrupt IN endpoint number"
|
|
default 1
|
|
---help---
|
|
The logical 7-bit address of a hardware endpoint that supports
|
|
interrupt IN operation. Default 1.
|
|
|
|
endif # !CDCACM_COMPOSITE
|
|
|
|
config CDCACM_EPINTIN_FSSIZE
|
|
int "Interrupt IN full speed MAXPACKET size"
|
|
default 64
|
|
---help---
|
|
Max package size for the interrupt IN endpoint if full speed mode.
|
|
Default 64.
|
|
|
|
if USBDEV_DUALSPEED
|
|
|
|
config CDCACM_EPINTIN_HSSIZE
|
|
int "Interrupt IN high speed MAXPACKET size"
|
|
default 64
|
|
---help---
|
|
Max package size for the interrupt IN endpoint if high speed mode.
|
|
Default 64.
|
|
|
|
endif # USBDEV_DUALSPEED
|
|
|
|
if USBDEV_SUPERSPEED
|
|
|
|
config CDCACM_EPINTIN_SSSIZE
|
|
int "Interrupt IN super speed MAXPACKET size"
|
|
default 64
|
|
---help---
|
|
Max package size for the interrupt IN endpoint if super speed mode.
|
|
Default 64.
|
|
|
|
config CDCACM_EPINTIN_MAXBURST
|
|
int "Interrupt IN super speed MAXBURST size"
|
|
default 0
|
|
---help---
|
|
Max burst size for the interrupt IN endpoint if super speed mode.
|
|
Default 0.
|
|
|
|
endif # USBDEV_SUPERSPEED
|
|
|
|
if !CDCACM_COMPOSITE
|
|
|
|
# In a composite device the EP-Number is configured dynamically via
|
|
# composite_initialize
|
|
|
|
config CDCACM_EPBULKOUT
|
|
int "Bulk OUT endpoint number"
|
|
default 3
|
|
---help---
|
|
The logical 7-bit address of a hardware endpoint that supports
|
|
bulk OUT operation. Default: 3
|
|
|
|
endif # !CDCACM_COMPOSITE
|
|
|
|
config CDCACM_EPBULKOUT_FSSIZE
|
|
int "Bulk OUT full speed MAXPACKET size"
|
|
default 64
|
|
---help---
|
|
Max package size for the bulk OUT endpoint if full speed mode.
|
|
Default 64.
|
|
|
|
if USBDEV_DUALSPEED
|
|
|
|
config CDCACM_EPBULKOUT_HSSIZE
|
|
int "Bulk OUT high speed MAXPACKET size"
|
|
default 512
|
|
---help---
|
|
Max package size for the bulk OUT endpoint if high speed mode.
|
|
Default 512.
|
|
|
|
endif # USBDEV_DUALSPEED
|
|
|
|
if USBDEV_SUPERSPEED
|
|
|
|
config CDCACM_EPBULKOUT_SSSIZE
|
|
int "Bulk OUT super speed MAXPACKET size"
|
|
default 1024
|
|
---help---
|
|
Max package size for the bulk OUT endpoint if super speed mode.
|
|
Default 1024.
|
|
|
|
config CDCACM_EPBULKOUT_MAXBURST
|
|
int "Bulk OUT super speed MAXBURST size"
|
|
default 0
|
|
---help---
|
|
Max burst size for the bulk OUT endpoint if super speed mode.
|
|
Default 0.
|
|
|
|
config CDCACM_EPBULKOUT_MAXSTREAM
|
|
int "Bulk OUT super speed MAXSTREAM size"
|
|
default 0
|
|
---help---
|
|
Max stream size for the bulk OUT endpoint if super speed mode.
|
|
Default 0.
|
|
|
|
endif # USBDEV_SUPERSPEED
|
|
|
|
if !CDCACM_COMPOSITE
|
|
|
|
# In a composite device the EP-Number is configured dynamically via
|
|
# composite_initialize
|
|
|
|
config CDCACM_EPBULKIN
|
|
int "Bulk IN endpoint number"
|
|
default 2
|
|
---help---
|
|
The logical 7-bit address of a hardware endpoint that supports
|
|
bulk IN operation. Default: 2
|
|
|
|
endif
|
|
|
|
config CDCACM_EPBULKIN_FSSIZE
|
|
int "Bulk IN full speed MAXPACKET size"
|
|
default 64
|
|
---help---
|
|
Max package size for the bulk IN endpoint if full speed mode.
|
|
Default 64.
|
|
|
|
if USBDEV_DUALSPEED
|
|
|
|
config CDCACM_EPBULKIN_HSSIZE
|
|
int "Bulk IN high speed MAXPACKET size"
|
|
default 512
|
|
---help---
|
|
Max package size for the bulk IN endpoint if high speed mode.
|
|
Default 512.
|
|
|
|
endif # USBDEV_DUALSPEED
|
|
|
|
if USBDEV_SUPERSPEED
|
|
|
|
config CDCACM_EPBULKIN_SSSIZE
|
|
int "Bulk IN super speed MAXPACKET size"
|
|
default 1024
|
|
---help---
|
|
Max package size for the bulk IN endpoint if super speed mode.
|
|
Default 1024.
|
|
|
|
config CDCACM_EPBULKIN_MAXBURST
|
|
int "Bulk IN super speed MAXBURST size"
|
|
default 0
|
|
---help---
|
|
Max burst size for the bulk IN endpoint if super speed mode.
|
|
Default 0.
|
|
|
|
config CDCACM_EPBULKIN_MAXSTREAM
|
|
int "Bulk IN super speed MAXSTREAM size"
|
|
default 0
|
|
---help---
|
|
Max stream size for the bulk IN endpoint if super speed mode.
|
|
Default 0.
|
|
|
|
endif # USBDEV_SUPERSPEED
|
|
|
|
config CDCACM_NRDREQS
|
|
int "Number of read requests that can be in flight"
|
|
default 4
|
|
---help---
|
|
The number of read requests that can be in flight
|
|
|
|
config CDCACM_NWRREQS
|
|
int "Number of write requests that can be in flight"
|
|
default 4
|
|
---help---
|
|
The number of write/read requests that can be in flight
|
|
|
|
config CDCACM_BULKIN_REQLEN
|
|
int "Size of one write request buffer"
|
|
default 768 if USBDEV_DUALSPEED
|
|
default 96 if !USBDEV_DUALSPEED
|
|
---help---
|
|
Ideally, the BULKOUT request size should *not* be the same size as
|
|
the maxpacket size. That is because IN transfers of exactly the
|
|
maxpacket size will be followed by a NULL packet. The BULKOUT,
|
|
on the other hand, request buffer size is always the same as the
|
|
maxpacket size.
|
|
|
|
There is also no reason from CDCACM_BULKIN_REQLEN to be greater
|
|
than CDCACM_TXBUFSIZE-1, since a request larger than the TX
|
|
buffer can never be sent.
|
|
|
|
config CDCACM_RXBUFSIZE
|
|
int "Receive buffer size"
|
|
default 513 if USBDEV_DUALSPEED
|
|
default 257 if !USBDEV_DUALSPEED
|
|
---help---
|
|
Size of the serial receive buffers. The actual amount of data that
|
|
can be held in the buffer is this number minus one due to the way
|
|
that the circular buffer is managed. So an RX buffer size of 257
|
|
will hold four full-speed, 64 byte packets; a buffer size of 513
|
|
will hold one high-speed, 512 byte packet.
|
|
|
|
config CDCACM_TXBUFSIZE
|
|
int "Transmit buffer size"
|
|
default 769 if USBDEV_DUALSPEED
|
|
default 193 if !USBDEV_DUALSPEED
|
|
---help---
|
|
Size of the serial transmit buffers. The actual amount of data that
|
|
can be held in the buffer is this number minus one due to the way
|
|
that the circular buffer is managed. So a TX buffer size of 769
|
|
will hold one request of size 768; a buffer size of 193 will hold
|
|
two requests of size 96 bytes.
|
|
|
|
if !CDCACM_COMPOSITE
|
|
|
|
# In a composite device the Vendor- and Product-ID is given by the composite
|
|
# device
|
|
|
|
config CDCACM_VENDORID
|
|
hex "Vendor ID"
|
|
default 0x0525
|
|
---help---
|
|
The vendor ID code/string. Default 0x0525 and "NuttX"
|
|
0x0525 is the Netchip vendor and should not be used in any
|
|
products. This default VID was selected for compatibility with
|
|
the Linux CDC ACM default VID.
|
|
|
|
config CDCACM_PRODUCTID
|
|
hex "Product ID"
|
|
default 0xa4a7
|
|
---help---
|
|
The product ID code/string. Default 0xa4a7 and "CDC/ACM Serial"
|
|
0xa4a7 was selected for compatibility with the Linux CDC ACM
|
|
default PID.
|
|
|
|
config CDCACM_VENDORSTR
|
|
string "Vendor string"
|
|
default "NuttX"
|
|
|
|
config CDCACM_PRODUCTSTR
|
|
string "Product string"
|
|
default "CDC/ACM Serial"
|
|
|
|
endif # !CDCACM_COMPOSITE
|
|
endif # CDCACM
|
|
|
|
menuconfig USBADB
|
|
bool "USB Android Debug Bridge (ADB) support"
|
|
default n
|
|
select USBDEV_FS
|
|
---help---
|
|
Enables USB Android Debug Bridge (ADB) support
|
|
|
|
if USBADB
|
|
|
|
config USBFASTBOOT
|
|
bool "USB Android Debug Bridge (FASTBOOT) support"
|
|
default n
|
|
---help---
|
|
Enables USB Android Debug Bridge (FASTBOOT) support
|
|
|
|
menuconfig USBADB_COMPOSITE
|
|
bool "USBADB composite support"
|
|
default n
|
|
depends on USBDEV_COMPOSITE
|
|
---help---
|
|
Configure the ADB driver as part of a composite driver
|
|
(only if USBDEV_COMPOSITE is also defined)
|
|
|
|
if !USBADB_COMPOSITE
|
|
|
|
# In a composite device the EP0 config comes from the composite device
|
|
# and the EP-Number is configured dynamically via composite_initialize
|
|
|
|
config USBADB_EP0MAXPACKET
|
|
int "Endpoint 0 max packet size"
|
|
default 64
|
|
---help---
|
|
Endpoint 0 max packet size. Default 64.
|
|
|
|
# In a composite device the EP-Numbers are configured dynamically via
|
|
# composite_initialize
|
|
|
|
config USBADB_EPBULKOUT
|
|
int "Bulk OUT endpoint number"
|
|
default 1
|
|
---help---
|
|
The logical 7-bit address of a hardware endpoint that supports
|
|
bulk OUT operation. Default: 3
|
|
|
|
config USBADB_EPBULKIN
|
|
int "Bulk IN endpoint number"
|
|
default 2
|
|
---help---
|
|
The logical 7-bit address of a hardware endpoint that supports
|
|
bulk IN operation. Default: 2
|
|
endif
|
|
|
|
config USBADB_EPBULKOUT_FSSIZE
|
|
int "Bulk OUT full speed MAXPACKET size"
|
|
default 64
|
|
---help---
|
|
Max package size for the bulk OUT endpoint if full speed mode.
|
|
Default 64.
|
|
|
|
if USBDEV_DUALSPEED
|
|
|
|
config USBADB_EPBULKOUT_HSSIZE
|
|
int "Bulk OUT high speed MAXPACKET size"
|
|
default 512
|
|
---help---
|
|
Max package size for the bulk OUT endpoint if high speed mode.
|
|
Default 512.
|
|
|
|
endif # USBDEV_DUALSPEED
|
|
|
|
if USBDEV_SUPERSPEED
|
|
|
|
config USBADB_EPBULKOUT_SSSIZE
|
|
int "Bulk OUT super speed MAXPACKET size"
|
|
default 1024
|
|
---help---
|
|
Max package size for the bulk OUT endpoint if super speed mode.
|
|
Default 1024.
|
|
|
|
config USBADB_EPBULKOUT_MAXBURST
|
|
int "Bulk OUT super speed MAXBURST size"
|
|
default 0
|
|
---help---
|
|
Max burst size for the bulk OUT endpoint if super speed mode.
|
|
Default 0.
|
|
|
|
config USBADB_EPBULKOUT_MAXSTREAM
|
|
int "Bulk OUT super speed MAXBSTREAM size"
|
|
default 0
|
|
---help---
|
|
Max stream size for the bulk OUT endpoint if super speed mode.
|
|
Default 0.
|
|
|
|
endif # USBDEV_SUPERSPEED
|
|
|
|
config USBADB_EPBULKIN_FSSIZE
|
|
int "Bulk IN full speed MAXPACKET size"
|
|
default 64
|
|
---help---
|
|
Max package size for the bulk IN endpoint if full speed mode.
|
|
Default 64.
|
|
|
|
if USBDEV_DUALSPEED
|
|
|
|
config USBADB_EPBULKIN_HSSIZE
|
|
int "Bulk IN high speed MAXPACKET size"
|
|
default 512
|
|
---help---
|
|
Max package size for the bulk IN endpoint if high speed mode.
|
|
Default 512.
|
|
|
|
endif # USBDEV_DUALSPEED
|
|
|
|
if USBDEV_SUPERSPEED
|
|
|
|
config USBADB_EPBULKIN_SSSIZE
|
|
int "Bulk IN super speed MAXPACKET size"
|
|
default 1024
|
|
---help---
|
|
Max package size for the bulk IN endpoint if super speed mode.
|
|
Default 1024.
|
|
|
|
config USBADB_EPBULKIN_MAXBURST
|
|
int "Bulk IN super speed MAXBURST size"
|
|
default 0
|
|
---help---
|
|
Max burst size for the bulk IN endpoint if super speed mode.
|
|
Default 0.
|
|
|
|
config USBADB_EPBULKIN_MAXSTREAM
|
|
int "Bulk IN super speed MAXBSTREAM size"
|
|
default 0
|
|
---help---
|
|
Max stream size for the bulk IN endpoint if super speed mode.
|
|
Default 0.
|
|
|
|
endif # USBDEV_SUPERSPEED
|
|
|
|
config USBADB_NRDREQS
|
|
int "Number of read requests that can be in flight"
|
|
default 4
|
|
---help---
|
|
The number of read requests that can be in flight
|
|
|
|
config USBADB_NWRREQS
|
|
int "Number of write requests that can be in flight"
|
|
default 4
|
|
---help---
|
|
The number of write/read requests that can be in flight
|
|
|
|
if !USBADB_COMPOSITE
|
|
|
|
config USBADB_VENDORID
|
|
hex "Vendor ID"
|
|
default 0x18d1
|
|
---help---
|
|
The vendor ID code/string. Default is Google Inc.
|
|
|
|
config USBADB_PRODUCTID
|
|
hex "Product ID"
|
|
default 0x4e11
|
|
---help---
|
|
The product ID code/string. Default is Nexus One.
|
|
|
|
config USBADB_VENDORSTR
|
|
string "Vendor string"
|
|
default "NuttX"
|
|
|
|
config USBADB_PRODUCTSTR
|
|
string "Product string"
|
|
default "Debug Bridge"
|
|
|
|
config USBADB_SERIALSTR
|
|
string "Serial string"
|
|
default "1234"
|
|
depends on !BOARD_USBDEV_SERIALSTR
|
|
|
|
endif # !USBADB_COMPOSITE
|
|
|
|
config USBADB_CONFIGSTR
|
|
string "Configuration descriptor string"
|
|
default "ADB Config"
|
|
|
|
config USBADB_INTERFACESTR
|
|
string "Interface descriptor string"
|
|
default "ADB Interface"
|
|
|
|
endif # USBADB
|
|
|
|
menuconfig USBMSC
|
|
bool "USB Mass storage class device"
|
|
default n
|
|
---help---
|
|
References:
|
|
"Universal Serial Bus Mass Storage Class, Specification Overview,"
|
|
Revision 1.2, USB Implementer's Forum, June 23, 2003.
|
|
|
|
"Universal Serial Bus Mass Storage Class, Bulk-Only Transport,"
|
|
Revision 1.0, USB Implementer's Forum, September 31, 1999.
|
|
|
|
"SCSI Primary Commands - 3 (SPC-3)," American National Standard
|
|
for Information Technology, May 4, 2005
|
|
|
|
"SCSI Primary Commands - 4 (SPC-4)," American National Standard
|
|
for Information Technology, July 19, 2008
|
|
|
|
"SCSI Block Commands -2 (SBC-2)," American National Standard
|
|
for Information Technology, November 13, 2004
|
|
|
|
"SCSI Multimedia Commands - 3 (MMC-3)," American National Standard
|
|
for Information Technology, November 12, 2001
|
|
|
|
if USBMSC
|
|
|
|
config USBMSC_COMPOSITE
|
|
bool "Mass storage composite support"
|
|
default n
|
|
depends on USBDEV_COMPOSITE
|
|
---help---
|
|
Configure the mass storage driver as part of a composite driver
|
|
(only if USBDEV_COMPOSITE is also defined)
|
|
|
|
if !USBMSC_COMPOSITE
|
|
|
|
# In a composite device the EP-Number and STR-Number is configured
|
|
# dynamically via composite_initialize
|
|
|
|
config USBMSC_EP0MAXPACKET
|
|
int "Max packet size for endpoint 0"
|
|
default 64
|
|
---help---
|
|
Max packet size for endpoint 0
|
|
|
|
config USBMSC_EPBULKOUT
|
|
int "Bulk OUT endpoint number"
|
|
default 2
|
|
---help---
|
|
The logical 7-bit address of a hardware endpoints that support
|
|
bulk OUT and IN operations
|
|
|
|
config USBMSC_EPBULKIN
|
|
int "Bulk IN endpoint number"
|
|
default 3
|
|
---help---
|
|
The logical 7-bit address of a hardware endpoints that support
|
|
bulk OUT and IN operations
|
|
|
|
endif
|
|
|
|
config USBMSC_NWRREQS
|
|
int "The number of write requests that can be in flight"
|
|
default 4
|
|
---help---
|
|
The number of write/read requests that can be in flight
|
|
|
|
config USBMSC_NRDREQS
|
|
int "The number of read requests that can be in flight"
|
|
default 4
|
|
---help---
|
|
The number of write/read requests that can be in flight
|
|
|
|
config USBMSC_WRMULTIPLE
|
|
bool "Write multiple blocks at once if possible"
|
|
default n
|
|
---help---
|
|
Store multiple blocks and write them in a single request. This
|
|
speeds up the writing significantly with eMMC devices, for example,
|
|
because writing 512 bytes may be as fast as writing the complete
|
|
SUPER_PAGE_SIZE (see extended CSD [225] bits 0-3), which may be up
|
|
to 64Kb. Real-life example with different block sizes, using the
|
|
dd command with argument bs=512, bs=8k (USBMSC_NWRREQS = 4, and 16):
|
|
512b: 470 kb/s, 8k: 5.3 Mb/s. This is more than a tenfold increase
|
|
in the throughput. Without this option enabled, the block driver's
|
|
block size is always used, which is usually 512 bytes.
|
|
|
|
config USBMSC_BULKINREQLEN
|
|
int "Bulk IN request size"
|
|
default 512 if USBDEV_DUALSPEED
|
|
default 64 if !USBDEV_DUALSPEED
|
|
---help---
|
|
The size of the buffer in each WRITE request. This value should to be
|
|
at least as large as the endpoint maxpacket size . Most DCDs can divide
|
|
a large request buffer down and enqueue the smaller, outgoing packets
|
|
for better performance. So, ideally, the size of write request buffer
|
|
should be the size of one block device sector which is, often, 512
|
|
bytes. The default, however, is the minimum size of 512 or 64 bytes
|
|
(depending upon if dual speed operation is supported or not).
|
|
|
|
config USBMSC_BULKOUTREQLEN
|
|
int "Bulk OUT request size"
|
|
default 512 if USBDEV_DUALSPEED
|
|
default 64 if !USBDEV_DUALSPEED
|
|
---help---
|
|
The size of the buffer in each READ request. This value should to be
|
|
at least as large as the endpoint maxpacket size. Most DCDs will return
|
|
the completed READ request to the caller as each packet is received.
|
|
Therefore, there is no benefit in increasing the size of this buffer
|
|
beyond the maximum size of one packet. Default: 512 or 64 bytes
|
|
(depending upon if dual speed operation is supported or not).
|
|
|
|
if USBMSC_COMPOSITE
|
|
|
|
config USBMSC_IFNOBASE
|
|
int "Mass storage interface number"
|
|
default 0
|
|
---help---
|
|
With composite USB drivers, the interface is not guaranteed to be zero
|
|
but rather, may vary according to the order in which the devices are
|
|
declared in the board_composite_connect() -function. This function may
|
|
be found in the corresponding board file. This index number may need to
|
|
be adjusted to match the proper interface number.
|
|
|
|
endif
|
|
|
|
if !USBMSC_COMPOSITE
|
|
|
|
# In a composite device the Vendor- and Product-IDs are handled by the
|
|
# composite device
|
|
|
|
config USBMSC_VENDORID
|
|
hex "Mass storage Vendor ID"
|
|
default 0x584e
|
|
---help---
|
|
The vendor ID (VID). The value here is bogus. You should not use
|
|
it in any commercial products! You must go through the proper
|
|
channels to request a vendor ID for your company if you do not
|
|
already have one!
|
|
|
|
config USBMSC_VENDORSTR
|
|
string "Mass storage vendor string"
|
|
default "NuttX"
|
|
---help---
|
|
The vendor ID code/string
|
|
|
|
config USBMSC_PRODUCTID
|
|
hex "Mass storage Product ID"
|
|
default 0x5342
|
|
---help---
|
|
The product ID (PID).
|
|
|
|
config USBMSC_PRODUCTSTR
|
|
string "Mass storage product string"
|
|
default "Mass Storage"
|
|
|
|
endif # !USBMSC_COMPOSITE
|
|
|
|
config USBMSC_VERSIONNO
|
|
hex "USB MSC Version Number"
|
|
default 0x399
|
|
|
|
config USBMSC_REMOVABLE
|
|
bool "Mass storage removable"
|
|
default n
|
|
---help---
|
|
Select if the media is removable
|
|
USB Composite Device Configuration
|
|
|
|
config USBMSC_SCSI_PRIO
|
|
int "USBMSC SCSI daemon priority"
|
|
default 128
|
|
---help---
|
|
Priority of the SCSI kernel thread. This must be a relatively high
|
|
priority so that the SCSI daemon can be response to USB block driver
|
|
accesses.
|
|
|
|
config USBMSC_SCSI_STACKSIZE
|
|
int "USBMSC SCSI daemon stack size"
|
|
default DEFAULT_TASK_STACKSIZE
|
|
---help---
|
|
Stack size used with the SCSI kernel thread. The default value
|
|
is not tuned.
|
|
|
|
config USBMSC_NOT_STALL_BULKEP
|
|
bool "Not stall USBMSC bulk endpoints for workaround"
|
|
default n
|
|
---help---
|
|
Not stall USBMSC bulk endpoints in some conditions.
|
|
Because RP2040 usbdev driver cannot handle stalling/resuming bulk
|
|
endpoints well, this workaround is required.
|
|
|
|
endif
|
|
|
|
menuconfig RNDIS
|
|
bool "RNDIS Ethernet-over-USB"
|
|
default n
|
|
---help---
|
|
References:
|
|
- "MS-RNDIS: Remote Network Driver Interface Specification (RNDIS)
|
|
Protocol"
|
|
- "Remote NDIS To USB Mapping"
|
|
|
|
This option may required CONFIG_NETDEV_LATEINIT=y otherwise, the
|
|
power-up initialization may call the non-existent xxx_netinitialize().
|
|
This option is not automatically selected because it may be that
|
|
you have an additional network device that requires the early
|
|
xxx_netinitialize() call.
|
|
|
|
if RNDIS
|
|
|
|
config RNDIS_NWRREQS
|
|
int "The number of write requests that can be in flight"
|
|
default 4 if NET_TCP_WRITE_BUFFERS
|
|
default 2 if !NET_TCP_WRITE_BUFFERS
|
|
---help---
|
|
The number of write/read requests that can be in flight
|
|
|
|
config RNDIS_COMPOSITE
|
|
bool "RNDIS composite support"
|
|
default n
|
|
depends on USBDEV_COMPOSITE
|
|
---help---
|
|
Configure the RNDIS driver as part of a composite driver
|
|
(only if USBDEV_COMPOSITE is also defined)
|
|
|
|
if !RNDIS_COMPOSITE
|
|
|
|
config RNDIS_VENDORID
|
|
hex "RNDIS Vendor ID"
|
|
default 0x584e
|
|
---help---
|
|
The vendor ID (VID). The value here is bogus. You should not use
|
|
it in any commercial products! You must go through the proper
|
|
channels to request a vendor ID for your company if you do not
|
|
already have one!
|
|
|
|
config RNDIS_VENDORSTR
|
|
string "RNDIS vendor string"
|
|
default "NuttX"
|
|
---help---
|
|
The vendor ID code/string
|
|
|
|
config RNDIS_PRODUCTID
|
|
hex "RNDIS Product ID"
|
|
default 0x5342
|
|
---help---
|
|
The product ID (PID).
|
|
|
|
config RNDIS_PRODUCTSTR
|
|
string "RNDIS product string"
|
|
default "RNDIS gadget"
|
|
|
|
config RNDIS_SERIALSTR
|
|
string "RNDIS serial string"
|
|
default "1234"
|
|
depends on !BOARD_USBDEV_SERIALSTR
|
|
|
|
config RNDIS_VERSIONNO
|
|
hex "RNDIS Version Number"
|
|
default 0x0001
|
|
|
|
config RNDIS_EPBULKIN
|
|
int "RNDIS bulk in endpoint number"
|
|
default 1
|
|
|
|
config RNDIS_EPBULKOUT
|
|
int "RNDIS bulk out endpoint number"
|
|
default 2
|
|
|
|
config RNDIS_EPINTIN
|
|
int "RNDIS interrupt in endpoint number"
|
|
default 3
|
|
|
|
endif # !RNDIS_COMPOSITE
|
|
|
|
endif # RNDIS
|
|
|
|
menuconfig DFU
|
|
bool "DFU Device Firmware Upgrade"
|
|
default n
|
|
---help---
|
|
References:
|
|
- "Universal Serial Bus Device Class Specification for Device
|
|
Firmware Upgrade, Version 1.1, Aug 5, 2004"
|
|
|
|
This driver implements the application-part of DFU protocol. It enables
|
|
a host application to send DFU_DETACH request and to cause the device
|
|
to reboot into a bootloader mode.
|
|
|
|
if DFU
|
|
|
|
config DFU_MSFT_OS_DESCRIPTORS
|
|
bool "Microsoft OS descriptor support"
|
|
default n
|
|
depends on COMPOSITE_MSFT_OS_DESCRIPTORS
|
|
---help---
|
|
Enabling this option will cause the DFU driver to return "WINUSB" as
|
|
the compatible ID of the DFU interface. This will automatically load
|
|
the appropriate driver for use with e.g. libusb and dfu-util.
|
|
Note that as of 2018 there are some issues with libusb and
|
|
composite devices, you may need a patched version:
|
|
https://sourceforge.net/p/libusb/mailman/message/36304399/
|
|
|
|
config DFU_INTERFACE_NAME
|
|
string "DFU interface string"
|
|
default "DFU interface"
|
|
---help---
|
|
String to assign as a name for the DFU interface.
|
|
|
|
if DFU_MSFT_OS_DESCRIPTORS
|
|
|
|
config DFU_INTERFACE_GUID
|
|
string "DFU interface GUID"
|
|
default "{8FE6D4D7-49DD-41E7-9486-49AFC6BFE475}"
|
|
---help---
|
|
DeviceInterfaceGUID to use for DFU interface in Microsoft OS descriptors.
|
|
Actual value does not matter for libusb, but if using WinUSB API directly
|
|
you can request your device by this GUID.
|
|
|
|
endif # DFU_MSFT_OS_DESCRIPTORS
|
|
endif # DFU
|
|
|
|
menuconfig NET_CDCECM
|
|
bool "CDC-ECM Ethernet-over-USB"
|
|
default n
|
|
select NETDEVICES
|
|
select NET
|
|
select NET_ETHERNET
|
|
---help---
|
|
References:
|
|
- "Universal Serial Bus - Communications Class - Subclass
|
|
Specification for Ethernet Control Model Devices,
|
|
Revision 1.2, February 9, 2007"
|
|
|
|
This option may require CONFIG_NETDEV_LATEINIT=y, otherwise the
|
|
power-up initialization may call the non-existent xxx_netinitialize().
|
|
This option is not automatically selected because it may be that
|
|
you have an additional network device that requires the early
|
|
xxx_netinitialize() call.
|
|
|
|
if NET_CDCECM
|
|
|
|
menuconfig CDCECM_COMPOSITE
|
|
bool "CDC/ECM composite support"
|
|
default n
|
|
depends on USBDEV_COMPOSITE
|
|
---help---
|
|
Configure the CDC Ethernet Control Model driver as part of a
|
|
composite driver (only if USBDEV_COMPOSITE is also defined)
|
|
|
|
if !CDCECM_COMPOSITE
|
|
|
|
# In a composite device the EP0 config comes from the composite device
|
|
# and the EP-Number is configured dynamically via composite_initialize
|
|
|
|
config CDCECM_EP0MAXPACKET
|
|
int "Endpoint 0 max packet size"
|
|
default 64
|
|
---help---
|
|
Endpoint 0 max packet size. Default 64.
|
|
|
|
config CDCECM_EPINTIN
|
|
int "Interrupt IN endpoint number"
|
|
default 1
|
|
---help---
|
|
The logical 7-bit address of a hardware endpoint that supports
|
|
interrupt IN operation. Default 1.
|
|
|
|
endif # !CDCECM_COMPOSITE
|
|
|
|
config CDCECM_EPINTIN_FSSIZE
|
|
int "Interrupt IN full speed MAXPACKET size"
|
|
default 16
|
|
---help---
|
|
Max package size for the interrupt IN endpoint if full speed mode.
|
|
Default 16.
|
|
|
|
if USBDEV_DUALSPEED
|
|
|
|
config CDCECM_EPINTIN_HSSIZE
|
|
int "Interrupt IN high speed MAXPACKET size"
|
|
default 64
|
|
---help---
|
|
Max package size for the interrupt IN endpoint if high speed mode.
|
|
Default 64.
|
|
|
|
endif # USBDEV_DUALSPEED
|
|
|
|
if USBDEV_SUPERSPEED
|
|
|
|
config CDCECM_EPINTIN_SSSIZE
|
|
int "Interrupt IN super speed MAXPACKET size"
|
|
default 64
|
|
---help---
|
|
Max package size for the interrupt IN endpoint if super speed mode.
|
|
Default 64.
|
|
|
|
config CDCECM_EPINTIN_MAXBURST
|
|
int "Interrupt IN super speed MAXBURST size"
|
|
default 0
|
|
---help---
|
|
Max burst size for the interrupt IN endpoint if super speed mode.
|
|
Default 0.
|
|
|
|
endif # USBDEV_SUPERSPEED
|
|
|
|
if !CDCECM_COMPOSITE
|
|
|
|
# In a composite device the EP-Number is configured dynamically via
|
|
# composite_initialize
|
|
|
|
config CDCECM_EPBULKOUT
|
|
int "Bulk OUT endpoint number"
|
|
default 5
|
|
---help---
|
|
The logical 7-bit address of a hardware endpoint that supports
|
|
bulk OUT operation. Default: 5
|
|
|
|
endif # !CDCECM_COMPOSITE
|
|
|
|
config CDCECM_EPBULKOUT_FSSIZE
|
|
int "Bulk OUT full speed MAXPACKET size"
|
|
default 64
|
|
---help---
|
|
Max package size for the bulk OUT endpoint if full speed mode.
|
|
Default 64.
|
|
|
|
if USBDEV_DUALSPEED
|
|
|
|
config CDCECM_EPBULKOUT_HSSIZE
|
|
int "Bulk OUT high speed MAXPACKET size"
|
|
default 512
|
|
---help---
|
|
Max package size for the bulk OUT endpoint if high speed mode.
|
|
Default 512.
|
|
|
|
endif # USBDEV_DUALSPEED
|
|
|
|
if USBDEV_SUPERSPEED
|
|
|
|
config CDCECM_EPBULKOUT_SSSIZE
|
|
int "Bulk OUT super speed MAXPACKET size"
|
|
default 1024
|
|
---help---
|
|
Max package size for the bulk OUT endpoint if super speed mode.
|
|
Default 1024.
|
|
|
|
config CDCECM_EPBULKOUT_MAXBURST
|
|
int "Bulk OUT super speed MAXBURST size"
|
|
default 0
|
|
---help---
|
|
Max burst size for the bulk OUT endpoint if super speed mode.
|
|
Default 0.
|
|
|
|
config CDCECM_EPBULKOUT_MAXSTREAM
|
|
int "Bulk OUT super speed MAXSTREAM size"
|
|
default 0
|
|
---help---
|
|
Max stream size for the bulk OUT endpoint if super speed mode.
|
|
Default 0.
|
|
|
|
endif # USBDEV_SUPERSPEED
|
|
|
|
if !CDCECM_COMPOSITE
|
|
|
|
# In a composite device the EP-Number is configured dynamically via
|
|
# composite_initialize
|
|
|
|
config CDCECM_EPBULKIN
|
|
int "Bulk IN endpoint number"
|
|
default 2
|
|
---help---
|
|
The logical 7-bit address of a hardware endpoint that supports
|
|
bulk IN operation. Default: 2
|
|
|
|
endif # !CDCECM_COMPOSITE
|
|
|
|
config CDCECM_EPBULKIN_FSSIZE
|
|
int "Bulk IN full speed MAXPACKET size"
|
|
default 64
|
|
---help---
|
|
Max package size for the bulk IN endpoint if full speed mode.
|
|
Default 64.
|
|
|
|
if USBDEV_DUALSPEED
|
|
|
|
config CDCECM_EPBULKIN_HSSIZE
|
|
int "Bulk IN high speed MAXPACKET size"
|
|
default 512
|
|
---help---
|
|
Max package size for the bulk IN endpoint if high speed mode.
|
|
Default 512.
|
|
|
|
endif # USBDEV_DUALSPEED
|
|
|
|
if USBDEV_SUPERSPEED
|
|
|
|
config CDCECM_EPBULKIN_SSSIZE
|
|
int "Bulk IN super speed MAXPACKET size"
|
|
default 1024
|
|
---help---
|
|
Max package size for the bulk IN endpoint if super speed mode.
|
|
Default 1024.
|
|
|
|
config CDCECM_EPBULKIN_MAXBURST
|
|
int "Bulk IN super speed MAXBURST size"
|
|
default 0
|
|
---help---
|
|
Max burst size for the bulk IN endpoint if super speed mode.
|
|
Default 0.
|
|
|
|
config CDCECM_EPBULKIN_MAXSTREAM
|
|
int "Bulk IN super speed MAXSTREAM size"
|
|
default 0
|
|
---help---
|
|
Max stream size for the bulk IN endpoint if super speed mode.
|
|
Default 0.
|
|
|
|
endif # USBDEV_SUPERSPEED
|
|
|
|
if !CDCECM_COMPOSITE
|
|
|
|
# In a composite device the Vendor- and Product-ID is given by the composite
|
|
# device
|
|
|
|
config CDCECM_VENDORID
|
|
hex "Vendor ID"
|
|
default 0x0525
|
|
---help---
|
|
The vendor ID code/string. Default 0x0525 and "NuttX"
|
|
0x0525 is the Netchip vendor and should not be used in any
|
|
products. This default VID was selected for compatibility with
|
|
the Linux CDC ECM default VID.
|
|
|
|
config CDCECM_PRODUCTID
|
|
hex "Product ID"
|
|
default 0xa4a2
|
|
---help---
|
|
The product ID code/string. Default 0xa4a2 and "CDC/ECM Ethernet"
|
|
0xa4a2 was selected for compatibility with the Linux CDC ECM
|
|
default PID.
|
|
|
|
config CDCECM_VENDORSTR
|
|
string "Vendor string"
|
|
default "NuttX"
|
|
|
|
config CDCECM_PRODUCTSTR
|
|
string "Product string"
|
|
default "CDC/ECM Ethernet"
|
|
|
|
endif # !CDCECM_COMPOSITE
|
|
endif # CDCECM
|
|
|
|
|
|
menuconfig NET_CDCNCM
|
|
bool "CDC-NCM Ethernet-over-USB"
|
|
default n
|
|
depends on SCHED_WORKQUEUE
|
|
depends on NETDEVICES
|
|
depends on NET
|
|
depends on NET_ETHERNET
|
|
---help---
|
|
References:
|
|
- "Universal Serial Bus - Communications Class - Subclass
|
|
Specification for Ethernet Control Model Devices,
|
|
Revision 1.2, February 9, 2007"
|
|
|
|
This option may require CONFIG_NETDEV_LATEINIT=y, otherwise the
|
|
power-up initialization may call the non-existent xxx_netinitialize().
|
|
This option is not automatically selected because it may be that
|
|
you have an additional network device that requires the early
|
|
xxx_netinitialize() call.
|
|
|
|
if NET_CDCNCM
|
|
|
|
config NET_CDCMBIM
|
|
bool "CDC-MBIM Ethernet-over-USB"
|
|
default n
|
|
---help---
|
|
This option may require CONFIG_NETDEV_LATEINIT=y, otherwise the
|
|
power-up initialization may call the non-existent xxx_netinitialize().
|
|
This option is not automatically selected because it may be that
|
|
you have an additional network device that requires the early
|
|
xxx_netinitialize() call.
|
|
|
|
menuconfig CDCNCM_COMPOSITE
|
|
bool "CDC/NCM composite support"
|
|
default n
|
|
depends on USBDEV_COMPOSITE
|
|
---help---
|
|
Configure the CDC Ethernet Control Model driver as part of a
|
|
composite driver (only if USBDEV_COMPOSITE is also defined)
|
|
|
|
if !CDCNCM_COMPOSITE
|
|
|
|
# In a composite device the EP0 config comes from the composite device
|
|
# and the EP-Number is configured dynamically via composite_initialize
|
|
|
|
config CDCNCM_EP0MAXPACKET
|
|
int "Endpoint 0 max packet size"
|
|
default 64
|
|
---help---
|
|
Endpoint 0 max packet size. Default 64.
|
|
|
|
config CDCNCM_EPINTIN
|
|
int "Interrupt IN endpoint number"
|
|
default 1
|
|
---help---
|
|
The logical 7-bit address of a hardware endpoint that supports
|
|
interrupt IN operation. Default 1.
|
|
|
|
endif # !CDCNCM_COMPOSITE
|
|
|
|
config CDCNCM_EPINTIN_FSSIZE
|
|
int "Interrupt IN full speed MAXPACKET size"
|
|
default 16
|
|
---help---
|
|
Max package size for the interrupt IN endpoint if full speed mode.
|
|
Default 16.
|
|
|
|
if USBDEV_DUALSPEED
|
|
|
|
config CDCNCM_EPINTIN_HSSIZE
|
|
int "Interrupt IN high speed MAXPACKET size"
|
|
default 64
|
|
---help---
|
|
Max package size for the interrupt IN endpoint if high speed mode.
|
|
Default 64.
|
|
|
|
endif # USBDEV_DUALSPEED
|
|
|
|
if USBDEV_SUPERSPEED
|
|
|
|
config CDCNCM_EPINTIN_SSSIZE
|
|
int "Interrupt IN super speed MAXPACKET size"
|
|
default 64
|
|
---help---
|
|
Max package size for the interrupt IN endpoint if super speed mode.
|
|
Default 64.
|
|
|
|
config CDCNCM_EPINTIN_MAXBURST
|
|
int "Interrupt IN super speed MAXBURST size"
|
|
default 0
|
|
---help---
|
|
Max burst size for the interrupt IN endpoint if super speed mode.
|
|
Default 0.
|
|
|
|
endif # USBDEV_SUPERSPEED
|
|
|
|
if !CDCNCM_COMPOSITE
|
|
|
|
# In a composite device the EP-Number is configured dynamically via
|
|
# composite_initialize
|
|
|
|
config CDCNCM_EPBULKOUT
|
|
int "Bulk OUT endpoint number"
|
|
default 5
|
|
---help---
|
|
The logical 7-bit address of a hardware endpoint that supports
|
|
bulk OUT operation. Default: 5
|
|
|
|
endif # !CDCNCM_COMPOSITE
|
|
|
|
config CDCNCM_EPBULKOUT_FSSIZE
|
|
int "Bulk OUT full speed MAXPACKET size"
|
|
default 64
|
|
---help---
|
|
Max package size for the bulk OUT endpoint if full speed mode.
|
|
Default 64.
|
|
|
|
if USBDEV_DUALSPEED
|
|
|
|
config CDCNCM_EPBULKOUT_HSSIZE
|
|
int "Bulk OUT high speed MAXPACKET size"
|
|
default 512
|
|
---help---
|
|
Max package size for the bulk OUT endpoint if high speed mode.
|
|
Default 512.
|
|
|
|
endif # USBDEV_DUALSPEED
|
|
|
|
if USBDEV_SUPERSPEED
|
|
|
|
config CDCNCM_EPBULKOUT_SSSIZE
|
|
int "Bulk OUT super speed MAXPACKET size"
|
|
default 1024
|
|
---help---
|
|
Max package size for the bulk OUT endpoint if super speed mode.
|
|
Default 1024.
|
|
|
|
config CDCNCM_EPBULKOUT_MAXBURST
|
|
int "Bulk OUT super speed MAXBURST size"
|
|
default 0
|
|
---help---
|
|
Max burst size for the bulk OUT endpoint if super speed mode.
|
|
Default 0.
|
|
|
|
config CDCNCM_EPBULKOUT_MAXSTREAM
|
|
int "Bulk OUT super speed MAXSTREAM size"
|
|
default 0
|
|
---help---
|
|
Max stream size for the bulk OUT endpoint if super speed mode.
|
|
Default 0.
|
|
|
|
endif # USBDEV_SUPERSPEED
|
|
|
|
if !CDCNCM_COMPOSITE
|
|
|
|
# In a composite device the EP-Number is configured dynamically via
|
|
# composite_initialize
|
|
|
|
config CDCNCM_EPBULKIN
|
|
int "Bulk IN endpoint number"
|
|
default 2
|
|
---help---
|
|
The logical 7-bit address of a hardware endpoint that supports
|
|
bulk IN operation. Default: 2
|
|
|
|
endif # !CDCNCM_COMPOSITE
|
|
|
|
config CDCNCM_EPBULKIN_FSSIZE
|
|
int "Bulk IN full speed MAXPACKET size"
|
|
default 64
|
|
---help---
|
|
Max package size for the bulk IN endpoint if full speed mode.
|
|
Default 64.
|
|
|
|
if USBDEV_DUALSPEED
|
|
|
|
config CDCNCM_EPBULKIN_HSSIZE
|
|
int "Bulk IN high speed MAXPACKET size"
|
|
default 512
|
|
---help---
|
|
Max package size for the bulk IN endpoint if high speed mode.
|
|
Default 512.
|
|
|
|
endif # USBDEV_DUALSPEED
|
|
|
|
if USBDEV_SUPERSPEED
|
|
|
|
config CDCNCM_EPBULKIN_SSSIZE
|
|
int "Bulk IN super speed MAXPACKET size"
|
|
default 1024
|
|
---help---
|
|
Max package size for the bulk IN endpoint if super speed mode.
|
|
Default 1024.
|
|
|
|
config CDCNCM_EPBULKIN_MAXBURST
|
|
int "Bulk IN super speed MAXBURST size"
|
|
default 0
|
|
---help---
|
|
Max burst size for the bulk IN endpoint if super speed mode.
|
|
Default 0.
|
|
|
|
config CDCNCM_EPBULKIN_MAXSTREAM
|
|
int "Bulk IN super speed MAXSTREAM size"
|
|
default 0
|
|
---help---
|
|
Max stream size for the bulk IN endpoint if super speed mode.
|
|
Default 0.
|
|
|
|
endif # USBDEV_SUPERSPEED
|
|
|
|
if !CDCNCM_COMPOSITE
|
|
|
|
# In a composite device the Vendor- and Product-ID is given by the composite
|
|
# device
|
|
|
|
config CDCNCM_VENDORID
|
|
hex "Vendor ID"
|
|
default 0x0525
|
|
---help---
|
|
The vendor ID code/string. Default 0x0525 and "NuttX"
|
|
0x0525 is the Netchip vendor and should not be used in any
|
|
products. This default VID was selected for compatibility with
|
|
the Linux CDC NCM default VID.
|
|
|
|
config CDCNCM_PRODUCTID
|
|
hex "Product ID"
|
|
default 0xa4a2
|
|
---help---
|
|
The product ID code/string. Default 0xa4a2 and "CDC/NCM Ethernet"
|
|
0xa4a2 was selected for compatibility with the Linux CDC NCM
|
|
default PID.
|
|
|
|
config CDCNCM_VENDORSTR
|
|
string "Vendor string"
|
|
default "NuttX"
|
|
|
|
config CDCNCM_PRODUCTSTR
|
|
string "CDCNCM Product string"
|
|
default "CDC/NCM Ethernet"
|
|
|
|
if NET_CDCMBIM
|
|
|
|
config CDCMBIM_PRODUCTSTR
|
|
string "CDCMBIM Product string"
|
|
default "CDC/MBIM Ethernet"
|
|
|
|
endif # NET_CDCMBIM
|
|
|
|
endif # !CDCNCM_COMPOSITE
|
|
|
|
config CDCNCM_QUOTA_TX
|
|
int "The drive holds the maximum quota of TX"
|
|
default 8
|
|
|
|
config CDCNCM_QUOTA_RX
|
|
int "The drive holds the maximum quota of RX"
|
|
default 8
|
|
|
|
endif # CDCNCM
|
|
|
|
config USBDEV_FS
|
|
bool
|
|
default n
|
|
select SCHED_HPWORK
|
|
---help---
|
|
Enables USBDEV FS support, userspace can use fs to control USB device.
|
|
|
|
if USBDEV_FS
|
|
|
|
config USBDEV_FS_EPNUM
|
|
int "Number of EP for USBDEV FS"
|
|
default 4
|
|
---help---
|
|
Maximum number of eps for USBDEV FS.
|
|
|
|
config USBDEV_FS_NPOLLWAITERS
|
|
int "Number of poll waiters for USBDEV FS"
|
|
default 2
|
|
---help---
|
|
Maximum number of threads that can be waiting on poll().
|
|
|
|
config USBDEV_FS_NEP0REQS
|
|
int "Number of ep0 requests that can be in flight"
|
|
default 4
|
|
---help---
|
|
The number of ep0 requests that can be in flight
|
|
|
|
endif #USBDEV_FS
|
|
|
|
menuconfig USBMTP
|
|
bool "USB Media Transfer Protocol (MTP) support"
|
|
default n
|
|
select USBDEV_FS
|
|
---help---
|
|
Enables USB Media Transfer Protocol (MTP) support
|
|
|
|
if USBMTP
|
|
|
|
menuconfig USBMTP_COMPOSITE
|
|
bool "USBMTP composite support"
|
|
default n
|
|
depends on USBDEV_COMPOSITE
|
|
---help---
|
|
Configure the MTP driver as part of a composite driver
|
|
(only if USBDEV_COMPOSITE is also defined)
|
|
|
|
if !USBMTP_COMPOSITE
|
|
|
|
# In a composite device the EP0 config comes from the composite device
|
|
# and the EP-Number is configured dynamically via composite_initialize
|
|
|
|
config USBMTP_EP0MAXPACKET
|
|
int "Endpoint 0 max packet size"
|
|
default 64
|
|
---help---
|
|
Endpoint 0 max packet size. Default 64.
|
|
|
|
# In a composite device the EP-Numbers are configured dynamically via
|
|
# composite_initialize
|
|
|
|
config USBMTP_EPBULKIN
|
|
int "Bulk IN endpoint number"
|
|
default 1
|
|
---help---
|
|
The logical 7-bit address of a hardware endpoint that supports
|
|
bulk IN operation. Default: 1
|
|
|
|
config USBMTP_EPBULKOUT
|
|
int "Bulk OUT endpoint number"
|
|
default 2
|
|
---help---
|
|
The logical 7-bit address of a hardware endpoint that supports
|
|
bulk OUT operation. Default: 2
|
|
|
|
config USBMTP_EPINTIN
|
|
int "Interrupt IN endpoint number"
|
|
default 5
|
|
---help---
|
|
The logical 7-bit address of a hardware endpoint that supports
|
|
interrupt IN operation. Default: 5
|
|
|
|
endif
|
|
|
|
config USBMTP_EPBULKOUT_FSSIZE
|
|
int "Bulk OUT Full Speed MAXPACKET size"
|
|
default 64
|
|
---help---
|
|
Max package size for the bulk OUT endpoint if Full Speed mode.
|
|
Default 64.
|
|
|
|
if USBDEV_DUALSPEED
|
|
|
|
config USBMTP_EPBULKOUT_HSSIZE
|
|
int "Bulk OUT High Speed MAXPACKET size"
|
|
default 512
|
|
---help---
|
|
Max package size for the bulk OUT endpoint if High Speed mode.
|
|
Default 512.
|
|
|
|
endif # USBDEV_DUALSPEED
|
|
|
|
if USBDEV_SUPERSPEED
|
|
|
|
config USBMTP_EPBULKOUT_SSSIZE
|
|
int "Bulk OUT Super Speed MAXPACKET size"
|
|
default 1024
|
|
---help---
|
|
Max package size for the bulk OUT endpoint if Super Speed mode.
|
|
Default 1024.
|
|
|
|
config USBMTP_EPBULKOUT_MAXBURST
|
|
int "Bulk OUT Super Speed MAXBURST size"
|
|
default 0
|
|
---help---
|
|
Max burst size for the bulk OUT endpoint if Super Speed mode.
|
|
Default 0.
|
|
|
|
config USBMTP_EPBULKOUT_MAXSTREAM
|
|
int "Bulk OUT Super Speed MAXSTREAM size"
|
|
default 0
|
|
---help---
|
|
Max stream size for the bulk OUT endpoint if Super Speed mode.
|
|
Default 0.
|
|
|
|
endif # USBDEV_SUPERSPEED
|
|
|
|
config USBMTP_EPBULKIN_FSSIZE
|
|
int "Bulk IN Full Speed MAXPACKET size"
|
|
default 64
|
|
---help---
|
|
Max package size for the bulk IN endpoint if Full Speed mode.
|
|
Default 64.
|
|
|
|
if USBDEV_DUALSPEED
|
|
|
|
config USBMTP_EPBULKIN_HSSIZE
|
|
int "Bulk IN High Speed MAXPACKET size"
|
|
default 512
|
|
---help---
|
|
Max package size for the bulk IN endpoint if High Speed mode.
|
|
Default 512.
|
|
|
|
endif # USBDEV_DUALSPEED
|
|
|
|
if USBDEV_SUPERSPEED
|
|
|
|
config USBMTP_EPBULKIN_SSSIZE
|
|
int "Bulk IN Super Speed MAXPACKET size"
|
|
default 1024
|
|
---help---
|
|
Max package size for the bulk IN endpoint if Super Speed mode.
|
|
Default 1024.
|
|
|
|
config USBMTP_EPBULKIN_MAXBURST
|
|
int "Bulk IN Super Speed MAXBURST size"
|
|
default 0
|
|
---help---
|
|
Max burst size for the bulk IN endpoint if Super Speed mode.
|
|
Default 0.
|
|
|
|
config USBMTP_EPBULKIN_MAXSTREAM
|
|
int "Bulk IN Super Speed MAXSTREAM size"
|
|
default 0
|
|
---help---
|
|
Max stream size for the bulk IN endpoint if Super Speed mode.
|
|
Default 0.
|
|
|
|
endif # USBDEV_SUPERSPEED
|
|
|
|
config USBMTP_EPINTIN_SIZE
|
|
int "Interrupt IN MAXPACKET size"
|
|
default 28
|
|
---help---
|
|
Max package size for the Interrupt IN endpoint, Default 28.
|
|
|
|
config USBMTP_EPINTIN_INTERVAL
|
|
int "Interrupt IN poll interval"
|
|
default 10
|
|
---help---
|
|
The poll interval for the Interrupt IN endpoint, Default 10.
|
|
|
|
if USBDEV_SUPERSPEED
|
|
|
|
config USBMTP_EPINTIN_MAXBURST
|
|
int "Interrupt IN Super Speed MAXBURST size"
|
|
default 0
|
|
---help---
|
|
Max burst size for the Interrupt IN endpoint if Super Speed mode.
|
|
Default 0.
|
|
|
|
endif # USBDEV_SUPERSPEED
|
|
|
|
config USBMTP_NRDREQS
|
|
int "Number of read requests that can be in flight"
|
|
default 4
|
|
---help---
|
|
The number of read requests that can be in flight
|
|
|
|
config USBMTP_NWRREQS
|
|
int "Number of write requests that can be in flight"
|
|
default 4
|
|
---help---
|
|
The number of write/read requests that can be in flight
|
|
|
|
if !USBMTP_COMPOSITE
|
|
|
|
config USBMTP_VENDORID
|
|
hex "Vendor ID"
|
|
default 0x18d1
|
|
---help---
|
|
The vendor ID code/string. Default is Google Inc.
|
|
|
|
config USBMTP_PRODUCTID
|
|
hex "Product ID"
|
|
default 0x4e11
|
|
---help---
|
|
The product ID code/string. Default is Nexus One.
|
|
|
|
config USBMTP_VENDORSTR
|
|
string "Vendor string"
|
|
default "NuttX"
|
|
|
|
config USBMTP_PRODUCTSTR
|
|
string "Product string"
|
|
default "Nuttx MTP"
|
|
|
|
config USBMTP_SERIALSTR
|
|
string "Serial string"
|
|
default "1234"
|
|
depends on !USBMTP_BOARD_SERIALSTR
|
|
|
|
endif # !USBMTP_COMPOSITE
|
|
|
|
config USBMTP_CONFIGSTR
|
|
string "Configuration descriptor string"
|
|
default "MTP Config"
|
|
|
|
config USBMTP_INTERFACESTR
|
|
string "Interface descriptor string"
|
|
default "MTP Interface"
|
|
|
|
endif # USBMTP
|
|
|
|
endif # USBDEV
|