580 lines
22 KiB
Plaintext
580 lines
22 KiB
Plaintext
README
|
|
======
|
|
|
|
This README discusses issues unique to NuttX configurations for the
|
|
STMicro STM32L-Discovery development board. The STM32L-Discovery board
|
|
is based on the STM32L152RBT6 MCU (128KB FLASH and 16KB of SRAM).
|
|
|
|
The STM32L-Discovery and 32L152CDISCOVERY kits are functionally
|
|
equivalent. The difference is the internal Flash memory size (STM32L152RBT6
|
|
with 128 Kbytes or STM32L152RCT6 with 256 Kbytes).
|
|
|
|
Both boards feature:
|
|
|
|
- An ST-LINK/V2 embedded debug tool interface,
|
|
- LCD (24 segments, 4 commons),
|
|
- LEDs,
|
|
- Pushbuttons,
|
|
- A linear touch sensor, and
|
|
- Four touchkeys.
|
|
|
|
Contents
|
|
========
|
|
|
|
- Status
|
|
- GPIO Pin Usage
|
|
- LEDs
|
|
- Serial Console
|
|
- Debugging
|
|
- STM32L-Discovery-specific Configuration Options
|
|
- Configurations
|
|
|
|
Status
|
|
======
|
|
|
|
The basic port is complete. A NuttShell (NSH) configuration exists for the
|
|
STM32L-Discovery board. A driver has been developed for the segment LCD on
|
|
board the STM32L-Discovery. In the NSH configuration discription below,
|
|
there is information about how the basic NSH extension can be extended to
|
|
use apps/examples/slcd to exercise the segment LCD.
|
|
|
|
* The following subsystem have header files, drivers and have been
|
|
exercised: PWR, RCC, GPIO, SYSCFG, LCD, USART.
|
|
|
|
* The following subsystenms have header files and ported drivers, but are
|
|
untested: DMA
|
|
|
|
* The following subystems have counterparts with other STM32 parts, but
|
|
have not been ported or verified: ADC, DAC, TIM2-15, TIM9-11, RTC,
|
|
IWDG, WWDG, I2C, SPI, DBG. These may be close to functional depending
|
|
upon how close the IP is on the STM32L15X.
|
|
|
|
This might include also USB, FSMC, and SDIO.
|
|
|
|
* The following subsystems are unique to the STM32L and have not been
|
|
developed: COMP, TSIO, RI, OPAMP
|
|
|
|
* The STM32L15X does support USB, however, USB is not available on the
|
|
STM32L-Discovery board.
|
|
|
|
* These subystems are available on other STM32L15x/16x parts, but not on
|
|
the part used in the STM32L-Discovery board: CRC, AES, FSMC, SDIO
|
|
|
|
GPIO Pin Usage
|
|
==============
|
|
|
|
----- --------------------- -------------------------------- ----------------
|
|
GPIO ALTERNATE FUNCTION BOARD FUNCTION P1/P2
|
|
----- --------------------- -------------------------------- ----------------
|
|
PA0 WKUP1/USART2_CTS/ Push button (PA0), WAKE UP (Iuu) P1, pin 15
|
|
ADC_IN0/TIM2_CH1_ETR
|
|
/COMP1_INP
|
|
PA1 USART2_RTS/ADC_IN1/ LCD SEG0 P1, pin 16
|
|
TIM2_CH2/LCD_SEG0/
|
|
COMP1_INP
|
|
PA2 USART2_TX/ADC_IN2/ LCD SEG1 P1, pin 17
|
|
TIM2_CH3/TIM9_CH1/
|
|
LCD_SEG1/COMP1_INP
|
|
PA3 USART2_RX/ADC_IN3/ LCD SEG2 P1, pin 18
|
|
TIM2_CH4/TIM9_CH2/
|
|
LCD_SEG2/COMP1_INP
|
|
PA4 SPI1_NSS/USART2_CK/ Measurement (Iuu) P1, pin 19
|
|
ADC_IN4/DAC_OUT1/
|
|
COMP1_INP
|
|
PA5 SPI1_SCK/ADC_IN5/ --- P1, pin 20
|
|
DAC_OUT2/
|
|
TIM2_CH1_ETR/COMP1_
|
|
INP
|
|
PA6 SPI1_MISO/ADC_IN6/ Linear Touch Sensor (PA6) ---
|
|
TIM3_CH1/TIM1_BKIN/
|
|
LCD_SEG3/TIM10_CH1/
|
|
COMP1_INP
|
|
PA7 SPI1_MOSI/ADC_IN7/ Linear Touch Sensor (PA7) ---
|
|
TIM3_CH2/TIM1_CH1N
|
|
/LCD_SEG4/TIM11_CH1/
|
|
PA8 USART1_CK/MCO/ LCD glass COM0 P2, pin 23
|
|
LCD_COM0
|
|
PA9 USART1_TX/LCD_COM1 LCD glass COM1 P2, pin 22
|
|
PA10 USART1_RX/LCD_COM2 LCD glass COM2 P2, pin 21
|
|
PA11 USART1_CTS/USBDM/ --- P2, pin 20
|
|
SPI1_MISO
|
|
PA12 USART1_RTS/USBDP/ --- P2, pin 19
|
|
SPI1_MOSI
|
|
JTDI TIM2_CH1_ETR/PA15/ LCD_SEG12 P2, pin 16
|
|
SPI1_NSS/LCD_SEG17
|
|
----- --------------------- -------------------------------- ----------------
|
|
PB0 ADC_IN8/TIM3_CH3/ Linear Touch Sensor (PB0) ---
|
|
LCD_SEG5/COMP1_INP/
|
|
VREF_OUT
|
|
PB1 ADC_IN9/TIM3_CH4/ Linear Touch Sensor (PB1) ---
|
|
LCD_SEG6/COMP1_INP/
|
|
VREF_OUT
|
|
PB2/ --- --- P1, pin 21
|
|
BOOT1
|
|
JTDO TIM2_CH2/PB3/TRACES LCD_SEG3, SWO P2, pin 11
|
|
WO/SPI1_SCK/COMP2_I
|
|
NM/LCD_SEG7
|
|
JNTRST TIM3_CH1/PB4/SPI1_MIS SEG4 P2, pin 10
|
|
O/COMP2_INP/LCD_SEG8
|
|
PB5 I2C1_SMBAl/TIM3_CH2/ LCD SEG5 P2, pin 9
|
|
SPI1_MOSI/COMP2_INP/
|
|
LCD_SEG9
|
|
PB6 I2C1_SCL/TIM4_CH1/ LED Blue P2, pin 8
|
|
USART1_TX/LCD_SEG8
|
|
PB7 I2C1_SDA/TIM4_CH2/ LED Green P2, pin 7
|
|
USART1_RX/PVD_IN
|
|
PB8 TIM4_CH3/I2C1_SCL/ LCD SEG13 P2, pin 4
|
|
LCD_SEG16/TIM10_CH1
|
|
PB9 TIM4_CH4/I2C1_SDA/ LCD glass COM3 P2, pin 3
|
|
LCD_COM3/TIM11_CH1
|
|
PB10 I2C2_SCL/USART3_TX/ LCD SEG6 P1, pin 22
|
|
TIM2_CH3/LCD_SEG10
|
|
PB11 I2C2_SDA/USART3_RX/ LCD SEG7 P1, pin 23
|
|
TIM2_CH4/LCD_SEG11
|
|
PB12 SPI2_NSS/I2C2_SMBA/ LCD SEG8 P1, pin 24
|
|
USART3_CK/LCD_SEG12
|
|
2/ADC_IN18/COMP1_INP
|
|
/ TIM10_CH1
|
|
PB13 SPI2_SCK/USART3_CTS/ LCD SEG9 P1, pin 25
|
|
LCD_SEG13/ADC_IN19/
|
|
COMP1_INP/TIM9_CH1
|
|
PB14 SPI2_MISO/USART3_RT LCD SEG10 P1, pin 26
|
|
S/LCD_SEG14/ADC_IN20
|
|
/ COMP1_INP/TIM9_CH2
|
|
PB15 SPI2_MOSI/TIM1_CH3N/ LCD SEG11 P1, pin 27
|
|
LCD_SEG15/ADC_IN21/
|
|
COMP1_INP/TIM11_CH1/
|
|
RTC_50_60Hz
|
|
----- --------------------- -------------------------------- ----------------
|
|
PC0 ADC_IN10/LCD_SEG18/ LCD SEG14 P1, pin 11
|
|
COMP1_INP
|
|
PC1 ADC_IN11/LCD_SEG19/ LCD SEG15 P1, pin 12
|
|
COMP1_INP
|
|
PC2 ADC_IN12/LCD_SEG20/ LCD SEG16 P1, pin 13
|
|
COMP1_INP
|
|
PC3 ADC_IN13/LCD_SEG21/ LCD SEG17 P1, pin 14
|
|
COMP1_INP
|
|
PC4 ADC_IN14/LCD_SEG22/ Linear Touch Sensor (PC4) ---
|
|
COMP1_INP
|
|
PC5 ADC_IN15/LCD_SEG23/ Linear Touch Sensor (PC5) ---
|
|
COMP1_INP
|
|
PC6 TIM3_CH1/LCD_SEG24 LCD SEG18 P2, pin 27
|
|
PC7 TIM3_CH2/LCD_SEG25 LCD SEG19 P2, pin 26
|
|
PC8 TIM3_CH3/LCD_SEG26 LCD SEG20 P2, pin 25
|
|
PC9 TIM3_CH4/LCD_SEG27 LCD SEG21 P2, pin 24
|
|
PC10 USART3_TX/LCD_SEG28 LCD SEG22 P2, pin 15
|
|
/LCD_SEG40/LCD_COM4
|
|
PC11 USART3_RX/LCD_SEG2 LCD SEG23 P2, pin 14
|
|
9/LCD_SEG41/
|
|
LCD_COM5
|
|
PC12 USART3_CK/LCD_SEG3 --- P2, pin 13
|
|
0/LCD_SEG42/
|
|
LCD_COM6
|
|
PC13 RTC_AF1/WKUP2 2 CNT_ IDD CNT_EN P1, pin 4
|
|
EN 4
|
|
PC14 OSC32_IN 3 OSC32_IN OSC32_IN P1, pin 5
|
|
PC15 OSC32_OUT 4 OSC32_OUT OSC32_OUT P1, pin 6
|
|
----- --------------------- -------------------------------- ----------------
|
|
PD2 TIM3_ETR/LCD_SEG31/ --- P2, pin 12
|
|
LCD_SEG43/LCD_COM7
|
|
----- --------------------- -------------------------------- ----------------
|
|
|
|
LEDs
|
|
====
|
|
|
|
The STM32L-Discovery board has four LEDs. Two of these are controlled by
|
|
logic on the board and are not available for software control:
|
|
|
|
LD1 COM: LD2 default status is red. LD2 turns to green to indicate
|
|
that communications are in progress between the PC and the
|
|
ST-LINK/V2.
|
|
LD2 PWR: Red LED indicates that the board is powered.
|
|
|
|
And two LEDs can be controlled by software:
|
|
|
|
User LD3: Green LED is a user LED connected to the I/O PB7 of the
|
|
STM32L152 MCU.
|
|
User LD4: Blue LED is a user LED connected to the I/O PB6 of the
|
|
STM32L152 MCU.
|
|
|
|
These LEDs are not used by the board port unless CONFIG_ARCH_LEDS is
|
|
defined. In that case, the usage by the board port is defined in
|
|
include/board.h and src/up_leds.c. The LEDs are used to encode OS-related
|
|
events as follows:
|
|
|
|
SYMBOL Meaning LED state
|
|
LED3 LED4
|
|
------------------- ----------------------- -------- --------
|
|
LED_STARTED NuttX has been started OFF OFF
|
|
LED_HEAPALLOCATE Heap has been allocated OFF OFF
|
|
LED_IRQSENABLED Interrupts enabled OFF OFF
|
|
LED_STACKCREATED Idle stack created ON OFF
|
|
LED_INIRQ In an interrupt No change
|
|
LED_SIGNAL In a signal handler No change
|
|
LED_ASSERTION An assertion failed No change
|
|
LED_PANIC The system has crashed OFF Blinking
|
|
LED_IDLE STM32 is is sleep mode Not used
|
|
|
|
Serial Console
|
|
==============
|
|
|
|
The STM32L-Discovery has no on-board RS-232 driver. Further, there are no
|
|
USART pins that do not conflict with the on board resources, in particular,
|
|
the LCD: Most USART pins are available if the LCD is enabled; USART2 may
|
|
be used if either the LCD or the on-board LEDs are disabled.
|
|
|
|
PA9 USART1_TX LCD glass COM1 P2, pin 22
|
|
PA10 USART1_RX LCD glass COM2 P2, pin 21
|
|
PB6 USART1_TX LED Blue P2, pin 8
|
|
PB7 USART1_RX LED Green P2, pin 7
|
|
|
|
PA2 USART2_TX LCD SEG1 P1, pin 17
|
|
PA3 USART2_RX LCD SEG2 P1, pin 18
|
|
|
|
PB10 USART3_TX LCD SEG6 P1, pin 22
|
|
PB11 USART3_RX LCD SEG7 P1, pin 23
|
|
PC10 USART3_TX LCD SEG22 P2, pin 15
|
|
PC11 USART3_RX LCD SEG23 P2, pin 14
|
|
|
|
NOTES:
|
|
|
|
- GND and (external) 5V are available on both P1 and P2. Note: These
|
|
signals may be at lower voltage levels and, hence, may not properly
|
|
drive an external RS-232 transceiver.
|
|
|
|
- The crystal X3 is not installed on the STM32L3-Discovery. As a result,
|
|
the HSE clock is not available and the less accurate HSI must be used.
|
|
This may limit the accuracy of the computed baud, especially at higher
|
|
BAUD. The HSI is supposedly calibrated in the factory to within 1% at
|
|
room temperatures so perhaps this not a issue.
|
|
|
|
- According to the STM32L-Discovery User Manual, the LCD should be removed
|
|
from its socket if you use any of the LCD pins for any other purpose.
|
|
|
|
I have had no problems using the USART1 with PA9 and PA10 with a 3.3-5V
|
|
RS-232 transceiver module at 57600 baud. I have not tried higher baud
|
|
rates.
|
|
|
|
- There is no support for a USB serial connector on the STM32L-Discovery
|
|
board. The STM32L152 does support USB, but the USB pins are "free I/O"
|
|
on the board and no USB connector is provided. So the use of a USB
|
|
console is not option. If you need console output, you will need to
|
|
disable either LCD (and use any USART) or the LEDs (and use USART1)
|
|
|
|
Debugging
|
|
=========
|
|
|
|
STM32 ST-LINK Utility
|
|
---------------------
|
|
For simply writing to FLASH, I use the STM32 ST-LINK Utility. At least
|
|
version 2.4.0 is required (older versions do not recognize the STM32 F3
|
|
device). This utility is available from free from the STMicro website.
|
|
|
|
Debugging
|
|
---------
|
|
If you are going to use a debugger, you should make sure that the following
|
|
settings are selection in your configuration file:
|
|
|
|
CONFIG_DEBUG_SYMBOLS=y : Enable debug symbols in the build
|
|
CONFIG_ARMV7M_USEBASEPRI=y : Use the BASEPRI register to disable interrupts
|
|
|
|
OpenOCD
|
|
-------
|
|
I am told that OpenOCD will work with the ST-Link, but I have never tried
|
|
it.
|
|
|
|
https://github.com/texane/stlink
|
|
--------------------------------
|
|
This is an open source server for the ST-Link that I have never used.
|
|
|
|
Atollic GDB Server
|
|
------------------
|
|
You can use the Atollic IDE, but I have never done that either.
|
|
|
|
STM32L-Discovery-specific Configuration Options
|
|
===============================================
|
|
|
|
CONFIG_ARCH - Identifies the arch/ subdirectory. This should
|
|
be set to:
|
|
|
|
CONFIG_ARCH=arm
|
|
|
|
CONFIG_ARCH_family - For use in C code:
|
|
|
|
CONFIG_ARCH_ARM=y
|
|
|
|
CONFIG_ARCH_architecture - For use in C code:
|
|
|
|
CONFIG_ARCH_CORTEXM4=y
|
|
|
|
CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
|
|
|
|
CONFIG_ARCH_CHIP=stm32
|
|
|
|
CONFIG_ARCH_CHIP_name - For use in C code to identify the exact
|
|
chip:
|
|
|
|
CONFIG_ARCH_CHIP_STM32L152RB=y
|
|
|
|
CONFIG_ARCH_BOARD_STM32_CUSTOM_CLOCKCONFIG - Enables special STM32 clock
|
|
configuration features.
|
|
|
|
CONFIG_ARCH_BOARD_STM32_CUSTOM_CLOCKCONFIG=n
|
|
|
|
CONFIG_ARCH_BOARD - Identifies the configs subdirectory and
|
|
hence, the board that supports the particular chip or SoC.
|
|
|
|
CONFIG_ARCH_BOARD=stm32fldiscovery (for the STM32L-Discovery development board)
|
|
|
|
CONFIG_ARCH_BOARD_name - For use in C code
|
|
|
|
CONFIG_ARCH_BOARD_STM32FLDISCOVERY=y
|
|
|
|
CONFIG_ARCH_LOOPSPERMSEC - Must be calibrated for correct operation
|
|
of delay loops
|
|
|
|
CONFIG_ENDIAN_BIG - define if big endian (default is little
|
|
endian)
|
|
|
|
CONFIG_RAM_SIZE - Describes the installed DRAM (SRAM in this case):
|
|
|
|
CONFIG_RAM_SIZE=16384 (16Kb)
|
|
|
|
CONFIG_RAM_START - The start address of installed DRAM
|
|
|
|
CONFIG_RAM_START=0x20000000
|
|
|
|
CONFIG_STM32_CCMEXCLUDE - Exclude CCM SRAM from the HEAP
|
|
|
|
CONFIG_ARCH_FPU - The STM32L-Discovery does not support a floating point unit (FPU)
|
|
|
|
CONFIG_ARCH_FPU=n
|
|
|
|
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to boards that
|
|
have LEDs
|
|
|
|
CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
|
|
stack. If defined, this symbol is the size of the interrupt
|
|
stack in bytes. If not defined, the user task stacks will be
|
|
used during interrupt handling.
|
|
|
|
CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
|
|
|
|
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.
|
|
|
|
CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
|
|
cause a 100 second delay during boot-up. This 100 second delay
|
|
serves no purpose other than it allows you to calibrate
|
|
CONFIG_ARCH_LOOPSPERMSEC. You simply use a stop watch to measure
|
|
the 100 second delay then adjust CONFIG_ARCH_LOOPSPERMSEC until
|
|
the delay actually is 100 seconds.
|
|
|
|
Individual subsystems can be enabled:
|
|
|
|
AHB
|
|
----
|
|
(GPIOs are always enabled)
|
|
CONFIG_STM32_FLITF
|
|
CONFIG_STM32_DMA1
|
|
CONFIG_STM32_DMA2
|
|
|
|
APB2
|
|
----
|
|
CONFIG_STM32_SYSCFG
|
|
CONFIG_STM32_TIM9
|
|
CONFIG_STM32_TIM10
|
|
CONFIG_STM32_TIM11
|
|
CONFIG_STM32_ADC1
|
|
CONFIG_STM32_SPI1
|
|
CONFIG_STM32_USART1
|
|
|
|
APB1
|
|
----
|
|
CONFIG_STM32_TIM2
|
|
CONFIG_STM32_TIM3
|
|
CONFIG_STM32_TIM4
|
|
CONFIG_STM32_TIM5
|
|
CONFIG_STM32_TIM6
|
|
CONFIG_STM32_TIM7
|
|
CONFIG_STM32_LCD
|
|
CONFIG_STM32_WWDG
|
|
CONFIG_STM32_IWDG
|
|
CONFIG_STM32_SPI2
|
|
CONFIG_STM32_SPI3
|
|
CONFIG_STM32_USART2
|
|
CONFIG_STM32_USART3
|
|
CONFIG_STM32_I2C1
|
|
CONFIG_STM32_I2C2
|
|
CONFIG_STM32_USB
|
|
CONFIG_STM32_PWR -- Required for RTC
|
|
CONFIG_STM32_DAC1
|
|
CONFIG_STM32_COMP
|
|
|
|
Timer devices may be used for different purposes. One special purpose is
|
|
to generate modulated outputs for such things as motor control. If CONFIG_STM32_TIMn
|
|
is defined (as above) then the following may also be defined to indicate that
|
|
the timer is intended to be used for pulsed output modulation, ADC conversion,
|
|
or DAC conversion. Note that ADC/DAC require two definition: Not only do you have
|
|
to assign the timer (n) for used by the ADC or DAC, but then you also have to
|
|
configure which ADC or DAC (m) it is assigned to.
|
|
|
|
CONFIG_STM32_TIMn_PWM Reserve timer n for use by PWM, n=1,..,14
|
|
CONFIG_STM32_TIMn_ADC Reserve timer n for use by ADC, n=1,..,14
|
|
CONFIG_STM32_TIMn_ADCm Reserve timer n to trigger ADCm, n=1,..,14, m=1,..,3
|
|
CONFIG_STM32_TIMn_DAC Reserve timer n for use by DAC, n=1,..,14
|
|
CONFIG_STM32_TIMn_DACm Reserve timer n to trigger DACm, n=1,..,14, m=1,..,2
|
|
|
|
For each timer that is enabled for PWM usage, we need the following additional
|
|
configuration settings:
|
|
|
|
CONFIG_STM32_TIMx_CHANNEL - Specifies the timer output channel {1,..,4}
|
|
|
|
NOTE: The STM32 timers are each capable of generating different signals on
|
|
each of the four channels with different duty cycles. That capability is
|
|
not supported by this driver: Only one output channel per timer.
|
|
|
|
JTAG Enable settings (by default only SW-DP is enabled):
|
|
|
|
CONFIG_STM32_JTAG_FULL_ENABLE - Enables full SWJ (JTAG-DP + SW-DP)
|
|
CONFIG_STM32_JTAG_NOJNTRST_ENABLE - Enables full SWJ (JTAG-DP + SW-DP)
|
|
but without JNTRST.
|
|
CONFIG_STM32_JTAG_SW_ENABLE - Set JTAG-DP disabled and SW-DP enabled
|
|
|
|
STM32L-Discovery specific device driver settings
|
|
|
|
CONFIG_U[S]ARTn_SERIAL_CONSOLE - selects the USARTn (n=1,2,3) or UART
|
|
m (m=4,5) for the console and ttys0 (default is the USART1).
|
|
CONFIG_U[S]ARTn_RXBUFSIZE - Characters are buffered as received.
|
|
This specific the size of the receive buffer
|
|
CONFIG_U[S]ARTn_TXBUFSIZE - Characters are buffered before
|
|
being sent. This specific the size of the transmit buffer
|
|
CONFIG_U[S]ARTn_BAUD - The configure BAUD of the UART. Must be
|
|
CONFIG_U[S]ARTn_BITS - The number of bits. Must be either 7 or 8.
|
|
CONFIG_U[S]ARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
|
|
CONFIG_U[S]ARTn_2STOP - Two stop bits
|
|
|
|
STM32L-Discovery CAN Configuration
|
|
|
|
CONFIG_CAN - Enables CAN support (one or both of CONFIG_STM32_CAN1 or
|
|
CONFIG_STM32_CAN2 must also be defined)
|
|
CONFIG_CAN_EXTID - Enables support for the 29-bit extended ID. Default
|
|
Standard 11-bit IDs.
|
|
CONFIG_CAN_FIFOSIZE - The size of the circular buffer of CAN messages.
|
|
Default: 8
|
|
CONFIG_CAN_NPENDINGRTR - The size of the list of pending RTR requests.
|
|
Default: 4
|
|
CONFIG_CAN_LOOPBACK - A CAN driver may or may not support a loopback
|
|
mode for testing. The STM32 CAN driver does support loopback mode.
|
|
CONFIG_CAN1_BAUD - CAN1 BAUD rate. Required if CONFIG_STM32_CAN1 is defined.
|
|
CONFIG_CAN2_BAUD - CAN1 BAUD rate. Required if CONFIG_STM32_CAN2 is defined.
|
|
CONFIG_CAN_TSEG1 - The number of CAN time quanta in segment 1. Default: 6
|
|
CONFIG_CAN_TSEG2 - the number of CAN time quanta in segment 2. Default: 7
|
|
CONFIG_STM32_CAN_REGDEBUG - If CONFIG_DEBUG_FEATURES is set, this will generate an
|
|
dump of all CAN registers.
|
|
|
|
STM32L-Discovery SPI Configuration
|
|
|
|
CONFIG_STM32_SPI_INTERRUPTS - Select to enable interrupt driven SPI
|
|
support. Non-interrupt-driven, poll-waiting is recommended if the
|
|
interrupt rate would be to high in the interrupt driven case.
|
|
CONFIG_STM32_SPI_DMA - Use DMA to improve SPI transfer performance.
|
|
Cannot be used with CONFIG_STM32_SPI_INTERRUPT.
|
|
|
|
Configurations
|
|
==============
|
|
|
|
Each STM32L-Discovery configuration is maintained in a sub-directory and
|
|
can be selected as follow:
|
|
|
|
cd tools
|
|
./configure.sh STM32L-Discovery/<subdir>
|
|
cd -
|
|
|
|
Where <subdir> is one of the following sub-directories.
|
|
|
|
NOTE: These configurations use the mconf-based configuration tool. To
|
|
change any of these configurations using that tool, you should:
|
|
|
|
a. Build and install the kconfig-mconf tool. See nuttx/README.txt
|
|
see additional README.txt files in the NuttX tools repository.
|
|
|
|
b. Execute 'make menuconfig' in nuttx/ in order to start the
|
|
reconfiguration process.
|
|
|
|
Configuration sub-directories
|
|
-----------------------------
|
|
|
|
nsh:
|
|
---
|
|
Configures the NuttShell (nsh) located at apps/examples/nsh.
|
|
|
|
NOTES:
|
|
|
|
1. The serial console is on UART1 and NuttX LED support is enabled.
|
|
Therefore, you will need an external RS232 driver or TTL serial-to-
|
|
USB converter. The UART1 TX and RX pins should be available on
|
|
PA9 and PA10, respectively.
|
|
|
|
The serial console is configured for 57600 8N1 by default.
|
|
|
|
2. Support for NSH built-in applications is *not* enabled.
|
|
|
|
3. By default, this configuration uses the CodeSourcery toolchain
|
|
for Windows and builds under Cygwin (or probably MSYS). That
|
|
can easily be reconfigured, of course.
|
|
|
|
Build Setup:
|
|
CONFIG_HOST_WINDOWS=y : Builds under Windows
|
|
CONFIG_WINDOWS_CYGWIN=y : Using Cygwin
|
|
|
|
System Type:
|
|
CONFIG_ARMV7M_TOOLCHAIN_CODESOURCERYW=y : CodeSourcery for Windows
|
|
|
|
4. To enable SLCD support:
|
|
|
|
Board Selection:
|
|
CONFIG_ARCH_LEDS=n : Disable board LED support
|
|
|
|
Library Routines:
|
|
CONFIG_LIB_SLCDCODEC=y : Enable the SLCD CODEC
|
|
|
|
System Type -> STM32 Peripheral Support:
|
|
CONFIG_STM32_LCD=y : Enable the Segment LCD
|
|
|
|
When the LCD is enabled and the LEDs are disabled, the USART1
|
|
serial console will automatically move to PB6 and PB7 (you will get
|
|
a compilation error if you forget to disable the LEDs).
|
|
|
|
SIGNAL FUNCTION LED CONNECTION
|
|
------ ---------- ---------- -----------
|
|
PB6 USART1_TX LED Blue P2, pin 8
|
|
PB7 USART1_RX LED Green P2, pin 7
|
|
|
|
To enable apps/examples/slcd to test the SLCD:
|
|
|
|
Binary Formats:
|
|
CONFIG_BINFMT_DISABLE=n : Don't disable binary support
|
|
CONFIG_BUILTIN=y : Enable support for built-in binaries
|
|
|
|
Application Configuration -> NSH Library:
|
|
CONFIG_NSH_BUILTIN_APPS=y : Enable builtin apps in NSH
|
|
CONFIG_NSH_ARCHINIT=y : Needed to initialize the SLCD
|
|
|
|
Application Configuration -> Examples:
|
|
CONFIG_EXAMPLES_SLCD=y : Enable apps/examples/slcd
|
|
|
|
To enable LCD debug output:
|
|
|
|
Device Drivers:
|
|
CONFIG_LCD=y : (Needed to enable LCD debug)
|
|
|
|
Build Setup -> Debug Options:
|
|
CONFIG_DEBUG_FEATURES=y : Enable debug features
|
|
CONFIG_DEBUG_INFO=y : Enable LCD debug
|
|
|
|
NOTE: At this point in time, testing of the SLCD is very limited because
|
|
there is not much in apps/examples/slcd. Certainly there are more bugs
|
|
to be found. There are also many segment-encoded glyphs in stm32_lcd.c
|
|
But there is a basically functional driver with a working test setup
|
|
that can be extended if you want a fully functional SLCD driver.
|