sergiotarxz/nuttx
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
da8934180a
nuttx/Documentation/platforms/arm/stm32f4/boards/stm32f401rc-rs485/index.rst
Rodrigo Sim da8934180a board/stm32f401rc-rs485: Add support to Device Configuration over Telnet 
Signed-off-by: Rodrigo Sim rcsim10@gmail.com
2024-07-15 13:35:03 +08:00

635 lines
18 KiB
ReStructuredText
Raw Blame History

=================
stm32f401rc-rs485
=================
This page discusses issues unique to NuttX configurations for the
NuttX STM32F4-RS485 development board.
.. figure:: stm32f401rc_rs485.jpg
:align: center
Board information
=================
This board was release on NuttX International Workshop 2023 and developed based on
STM32F401RCT6 microcontroller.
STM32F401RCT6 microcontroller features:
- Arm 32-bit Cortex®-M4 CPU with FPU
- 256 Kbytes of Flash memory
- 64 Kbytes of SRAM
- Serial wire debug (SWD) & JTAG interfaces
- Up to 81 I/O ports with interrupt capability
- Up to 11 communication interfaces
- Up to 3 I2C interfaces
- Up to 3 USARTs
- Up to 4 SPIs
- SDIO interface
- USB 2.0 full-speed device/host/OTG controller with on-chip PHY
The board features:
- Digital I2C Temperature Sensor (TMP75)
- 2K bits (256x8) I2C EEPROM
- On-board RS485 Transceiver
- Two Analog Input Stages with Amplifier Buffer
- Two Analog Output Stages with Amplifier Buffer
- MicroSD Connector supporting 1 or 4-bit bus
- Four User LEDs
- Four User Buttons
- USB for DFU (Device Firmware Update) and USB device functionality, as well as powering the board
- Onboard voltage regulator from 5V to 3.3V
- SWD Pins for use as STLink (Pin header) and TC2030-IDC 6-Pin Tag-Connect Plug-of-Nails™ Connector
- Crystal for HS 8MHz
- Crystal for RTC 32.768KHz
Board documentation:
https://github.com/lucaszampar/NuttX_STM32F4_RS485_DevBoard
As F4 series have a USB DFuSe-capable BootROM [AN2606], the board can be flashed
via `dfu-util` over USB, or via `stm32flash` over UART without any debuggers.
LEDs
====
The STM32F4-RS485 has 4 software controllable LEDs.
===== =====
LED PINS
===== =====
LED_1 PC0
LED_2 PC1
LED_4 PC2
LED_5 PC3
===== =====
User Buttons
============
The STM32F4-RS485 has 4 user switches.
======= ===== ======
SWITCH PINS LABEL
======= ===== ======
SWIO_1 PB13 SW3
SWIO_2 PB14 SW4
SWIO_3 PB15 SW5
SWIO_4 PC6 SW6[1]
======= ===== ======
[1] The switch SWIO_4 (SW6) is disabled due a conflict with PIN
PC6 when using USART6.
UARTs
=====
The STM32F4-RS485 has 1 USART available for user.
USART6
------
========== =======
UART/USART PINS
========== =======
TX PC6 [1]
RX PC7
CK PA8
========== =======
[1] Warning you make need to reverse RX/TX on some RS-232 converters
SDCard support
==============
The STM32F4-RS485 has 1 SDCard slot connected as below:
========== =====
SDIO PINS
========== =====
SDIO_D0 PC8
SDIO_D1 PC9
SDIO_D2 PC10
SDIO_D3 PC11
SDIO_DK PC12
========== =====
EEPROM
======
The STM32F4-RS485 development board has serial EEPROM HX24LC02B, with 2k bits (256x8) and internally
organized with 32 pages of 8 bytes each. It is connected through I2C as below:
====== =====
I2C PINS
====== =====
SDA PB7
SCL PB8
====== =====
Users can enable EERPOM support on STM32F4-RS485 by following below configuration:
- Configure basic nsh::
./tools/configure.sh -l stm32f401rc-rs485:nsh
- Enable the following configs::
CONFIG_DEV_ZERO=y
CONFIG_EEPROM=y
CONFIG_FS_PROCFS=y
CONFIG_I2C=y
CONFIG_I2C_EE_24XX=y
CONFIG_STM32_I2C1=y
- Build and flash the STM32F4-RS485.
- Use dd command to write and read data from EEPROM as below::
nsh> dd if=/dev/zero of=/dev/eeprom
nsh: dd: write failed: 1
nsh> dd if=/dev/console of=/dev/eeprom bs=1 count=4
(type "Hello")
nsh> dd if=/dev/eeprom of=/dev/console bs=4 count=1
Hellonsh>
Temperature Sensor
==================
The STM32F4-RS485 development board has a temperature sensor TMP75 (compatible with LM75) connected through I2C as below:
====== =====
I2C PINS
====== =====
SDA PB7
SCL PB8
====== =====
RS485 Transceiver
=================
The STM32F4-RS485 development board has a half-duplex RS-485 transceiver, the BL3085B it is connected
through USART2 as below:
========== =====
USART2 PINS
========== =====
USART2_RX RO
USART2_RTS DE, /RE
USART2_RX DI
========== =====
A/D Converter
=============
The STM32F4-RS485 development board has two Analog to Digital converters with Amplifier Buffer (1COS724SR)
and connected as below:
======= =====
PWM PINS
======= =====
PWM_1 PB6
PWM_2 PA6
======= =====
D/C Converter
=============
The STM32F4-RS485 development board has two Digital to Analog converters with Amplifier Buffer (1COS724SR)
and connected as below:
======= =====
ADC PINS
======= =====
ADC_1 PA0
ADC_2 PA4
======= =====
Configurations
==============
Each stm32f401rc-rs485 configuration is maintained in a sub-directory and
can be selected as follow::
tools/configure.sh stm32f401rc-rs485:<subdir>
Where <subdir> is one of the following:
Configuration Directories
-------------------------
nsh
---
Configures the NuttShell (nsh) located at apps/examples/nsh. This
configuration enables a serial console on USART6.
usbnsh
------
Configures the NuttShell (nsh) located at apps/examples/nsh. This
configuration enables a serial console over USB.
After flasing and reboot your board you should see in your dmesg logs::
[ 2638.948089] usb 1-1.4: new full-speed USB device number 16 using xhci_hcd
[ 2639.054432] usb 1-1.4: New USB device found, idVendor=0525, idProduct=a4a7, bcdDevice= 1.01
[ 2639.054437] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2639.054438] usb 1-1.4: Product: CDC/ACM Serial
[ 2639.054440] usb 1-1.4: Manufacturer: NuttX
[ 2639.054441] usb 1-1.4: SerialNumber: 0
[ 2639.074861] cdc_acm 1-1.4:1.0: ttyACM0: USB ACM device
[ 2639.074886] usbcore: registered new interface driver cdc_acm
[ 2639.074887] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
You may need to press **ENTER** 3 times before the NSH show up.
sdcard
------
Configures the NuttShell (nsh) and enables SD card support.
The stm32f401rc-rs485 has an onboard microSD slot that should
be automatically registered as the block device /dev/mmcsd0 when
an SD card is present. The SD card can then be mounted by the
NSH commands::
nsh> mount -t procfs /proc
nsh> mount -t vfat /dev/mmcsd0 /mnt
modbus_slave
------------
Configures the NuttShell (nsh) and enables modbus in slave mode. This
configuration enables a serial console on USART6. The RS-485 is connected
to USART2. Follow below precedure to use modbus test aplication, you will
need a USB to RS-485 converter to connect the board to a PC via RS-485.
NuttShell configuration:
Run modbus application at NSH::
nsh> modbus -help
USAGE: modbus [-d|e|s|q|h]
Where:
-d : Disable protocol stack
-e : Enable the protocol stack
-s : Show current status
-q : Quit application
-h : Show this information
nsh> modbus -e
PC Configuration:
Download and install mbpoll aplication::
sudo apt install mbpoll
Check which TTY USB port is being used by you USB to RS-485 converter::
sudo dmesg
[99846.668209] usb 1-1.3: Product: USB Serial
[99846.676313] ch341 1-1.3:1.0: ch341-uart converter detected
[99846.677454] usb 1-1.3: ch341-uart converter now attached to ttyUSB1
Run the mbpoll as below::
mbpoll -a 10 -b 38400 -t 3 -r 1000 -c 4 /dev/ttyUSB1 -R
At PC terminal you will see the mbpoll application receiving the random values
generated by STM32F401RC-RS485 and transmitted over RS-485::
mbpoll 1.0-0 - FieldTalk(tm) Modbus(R) Master Simulator
Copyright © 2015-2019 Pascal JEAN, https://github.com/epsilonrt/mbpoll
This program comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it
under certain conditions; type 'mbpoll -w' for details.
Protocol configuration: Modbus RTU
Slave configuration...: address = [10]
start reference = 1000, count = 4
Communication.........: /dev/ttyUSB1, 38400-8E1
t/o 1.00 s, poll rate 1000 ms
Data type.............: 16-bit register, input register table
-- Polling slave 10... Ctrl-C to stop)
[1000]: 58080 (-7456)
[1001]: 0
[1002]: 0
[1003]: 0
-- Polling slave 10... Ctrl-C to stop)
[1000]: 6100
[1001]: 0
[1002]: 0
[1003]: 0
-- Polling slave 10... Ctrl-C to stop)
[1000]: 51010 (-14526)
[1001]: 0
[1002]: 0
[1003]: 0
-- Polling slave 10... Ctrl-C to stop)
[1000]: 12528
[1001]: 0
[1002]: 0
[1003]: 0
modbus_master
-------------
Configures the NuttShell (nsh) and enables modbus in master mode. This
configuration enables a serial console on USART6. The RS-485 is connected
to USART2. Follow below precedure to use modbusmaster test aplication, you will
need a USB to RS-485 converter to connect the board to a PC via RS-485.
PC Configuration:
Download and install diagslave aplication from https://www.modbusdriver.com/diagslave.html.
Check which TTY USB port is being used by you USB to RS-485 converter::
sudo dmesg
[99846.668209] usb 1-1.3: Product: USB Serial
[99846.676313] ch341 1-1.3:1.0: ch341-uart converter detected
[99846.677454] usb 1-1.3: ch341-uart converter now attached to ttyUSB1
Run the diagslave as below::
sudo diagslave -a 10 -b 38400 /dev/ttyUSB1
At PC terminal you will see the diagslave application listening to address 10,
notice that this address is configurable via MODBUSMASTER_SLAVEADDR::
diagslave 3.4 - FieldTalk(tm) Modbus(R) Diagnostic Slave Simulator
Copyright (c) 2002-2021 proconX Pty Ltd
Visit https://www.modbusdriver.com for Modbus libraries and tools.
Protocol configuration: Modbus RTU, frame tolerance = 0ms
Slave configuration: address = 10, master activity t/o = 3.00s
Serial port configuration: /dev/ttyUSB1, 38400, 8, 1, even
Server started up successfully.
Listening to network (Ctrl-C to stop)
Slave 10: readHoldingRegisters from 2, 1 references
.......
NuttShell configuration:
Run modbusmaster application at NSH::
NuttShell (NSH) NuttX-12.4.0
nsh> modbusmaster
Initializing modbus master...
Creating poll thread.
Sending 100 requests to slave 10
mbmaster_main: Exiting poll thread.
Modbus master statistics:
Requests count: 100
Responses count: 100
Errors count: 0
Deinitializing modbus master...
The application modbusmaster will send 100 requests, you can check on diagslave::
Server started up successfully.
Listening to network (Ctrl-C to stop)
Slave 10: readHoldingRegisters from 2, 1 references
Slave 10: readHoldingRegisters from 2, 1 references
Slave 10: readHoldingRegisters from 2, 1 references
Slave 10: readHoldingRegisters from 2, 1 references
Slave 10: readHoldingRegisters from 2, 1 references
Slave 10: readHoldingRegisters from 2, 1 references
Slave 10: readHoldingRegisters from 2, 1 references
lm75
----
Configures the NuttShell (nsh) over USB Serial (check usbserial configuration) and enables temperature sensor LM75.
NSH commands::
nsh> lm75 -help
Usage: temp [OPTIONS]
[-n count] selects the samples to collect. Default: 1 Current: 100
[-h] shows this message and exits
nsh> lm75 -n 3
30.13 degrees Celsius
30.13 degrees Celsius
30.13 degrees Celsius
adc
---
Configures the NuttShell (nsh) over USB Serial (check usbserial configuration) and enables ADC 1 on channels 0 and 4.
NSH commands::
nsh> adc -h
Usage: adc [OPTIONS]
Arguments are "sticky". For example, once the ADC device is
specified, that device will be re-used until it is changed.
"sticky" OPTIONS include:
[-p devpath] selects the ADC device. Default: /dev/adc0 Current: /dev/adc0
[-n count] selects the samples to collect. Default: 1 Current: 0
[-h] shows this message and exits
nsh> adc -n 2
adc_main: g_adcstate.count: 2
adc_main: Hardware initialized. Opening the ADC device: /dev/adc0
Sample:
1: channel: 0 value: 2684
Sample:
1: channel: 4 value: 2682
Currently there is a bug that causes the application to always read the same value for channel 0 and 4. If you want to read the value from channel 2, you will need to enable the config "ADC1 Scan Mode".
dac
---
Configures the NuttShell (nsh) over USB Serial (check usbserial configuration) and enables PWM 3 on channel 1.
Use pwm command on NSH to change dutty cycle, frequency and duration, use dac_out_2 to measure the output voltage.
NSH commands::
nsh> pwm -h
Usage: pwm [OPTIONS]
Arguments are "sticky". For example, once the PWM frequency is
specified, that frequency will be re-used until it is changed.
"sticky" OPTIONS include:
[-p devpath] selects the PWM device. Default: /dev/pwm0 Current: NONE
[-f frequency] selects the pulse frequency. Default: 100 Hz Current: 100 Hz
[-d duty] selects the pulse duty as a percentage. Default: 50 % Current: 50 %
[-t duration] is the duration of the pulse train in seconds. Default: 5 Current: 5
[-h] shows this message and exits
nsh> pwm -d 50 -t 3
pwm_main: starting output with frequency: 50 duty: 00007fff
pwm_main: stopping output
qencoder
--------
Configures the NuttShell (nsh) over USB Serial (check usbserial configuration) and enables Timer 3 on channels 1 and
2 to handle Quadrature Encoder.
NSH commands::
nsh> qe -help
Usage: qe [OPTIONS]
OPTIONS include:
[-p devpath] QE device path
[-n samples] Number of samples
[-t msec] Delay between samples (msec)
[-r] Reset the position to zero
[-h] Shows this message and exits
nsh> qe -p /dev/qe0 -n 5 -t 100 -r
nsh: qe: too many arguments
qe_main: Hardware initialized. Opening the encoder device: /dev/qe0
qe_main: Resetting the count...
qe_main: Number of samples: 5
qe_main: 1. 0
qe_main: 2. 0
qe_main: 3. 4
qe_main: 4. 2
qe_main: 5. 2
Terminating!
rndis
-----
Configures the NuttShell (nsh), enables a serial console on USART6 and enables RNDIS over USB.
NSH commands::
nsh> mount -t procfs /proc
nsh> ping -h
Usage: ping [-c <count>] [-i <interval>] [-W <timeout>] [-s <size>] <hostname>
ping -h
Where:
<hostname> is either an IPv4 address or the name of the remote host
that is requested the ICMPv4 ECHO reply.
-c <count> determines the number of pings. Default 10.
-i <interval> is the default delay between pings (milliseconds).
Default 1000.
-W <timeout> is the timeout for wait response (milliseconds).
Default 1000.
-s <size> specifies the number of data bytes to be sent. Default 56.
-h shows this text and exits.
nsh> ping 10.42.0.1
PING 10.42.0.1 56 bytes of data
56 bytes from 10.42.0.1: icmp_seq=0 time=0.0 ms
56 bytes from 10.42.0.1: icmp_seq=1 time=0.0 ms
...
10 packets transmitted, 10 received, 0% packet loss, time 10100 ms
rtt min/avg/max/mdev = 0.000/0.000/0.000/0.000 ms
usbmsc
------
Configures the NuttShell (nsh), enables a serial console on USART6 and enables USB Mass Storage.
NSH commands::
nsh> msconn
mcsonn_main: Creating block drivers
mcsonn_main: Configuring with NLUNS=1
mcsonn_main: handle=0x20004c10
mcsonn_main: Bind LUN=0 to /dev/mmcsd0
mcsonn_main: Connected
nsh> msdis
hcs04
-----
Configures the NuttShell (nsh) over USB Serial (check usbserial configuration) and enables ultrasonic sensor HC-SR04::
nsh> cat /dev/dist0
6241 --> value
6227
6241
6255
You can convert the value using following::
Convert to cm: value/58
Convert to inches: value/148
ssd1309
-------
This config is used to enable support to the transparent OLED display powered by SSD1309.
The resolution of this display is 128x64 (although the effective view is 128x56).
You can wire the display to your board this way:
======= =====
OLED PINS
======= =====
CS PB7
DC PB8
RESET PB6
SDA PA7
SCK PA5
======= =====
The board profile configures the NSH over USB and you can use the fb command to test::
NuttShell (NSH) NuttX-12.5.1
nsh> fb
VideoInfo:
fmt: 0
xres: 128
yres: 64
nplanes: 1
PlaneInfo (plane 0):
fbmem: 0x200034f8
fblen: 1024
stride: 16
display: 0
bpp: 1
Mapped FB: 0x200034f8
0: ( 0, 0) (128, 64)
1: ( 11, 5) (106, 54)
2: ( 22, 10) ( 84, 44)
3: ( 33, 15) ( 62, 34)
4: ( 44, 20) ( 40, 24)
5: ( 55, 25) ( 18, 14)
Test finished
nsh>
telnetd
-------
Configures the NuttShell (nsh), enables a serial console on USART6, enables RNDIS over USB and
enables Device Configuration over Telnet.
NSH commands::
nsh> mount -t procfs /proc
nsh> ifcong
Get the ip address assigned to eth0 and convert to hexadecimal, for example 192.168.1.2
becomes 0xC0A80102, than configure CONFIG_NETINIT_IPADDR and CONFIG_EXAMPLES_TELNETD_IPADDR,
also configure the router address, in this example it woukd be 0xC0A80101. After theses changes
rebuild and load the new firmware on your board::
nsh> mount -t procfs /proc
nsh> telnetd
At your host PC, telnet to IP address for the board::
$ telnet 192.168.01.02
Now you will be able to access the Device Configuration over Telnet::
Device Configuration over Telnet
You can add functions to setup your device
Type '?' and press <enter> for help
cfg> ?
Available commands:
help, ? - show help
reset - reset the board
exit - exit shell
Reference in New Issue View Git Blame Copy Permalink