configs/pic32mz-starterkit README
===============================
This README file discusses the port of NuttX to the Microchip PIC32MZ
Embedded Connectivity (EC) Starter Kit.
Contents
========
Port Status
Board Overview
On Board Debug Support
Creating Compatible NuttX HEX files
Tool Issues
Serial Console
LEDs
Configurations
Port Status
===========
As of this writing (2015-03-01), the basic port is complete including
minimal support for the NuttShell (NSH) over UART1. No testing has yet
been performed due to seemingly insurmountable debug problems:
Thusfar, no one has been successful using NuttX with MPLABX. All
debug is being performed using a J-Link debugger via some custom
interconnect boards.
Patches were provided by Kristopher Tate on 2015-03-21 that support the
serial console with the NuttShell, completing the basic bring-up.
Board Overview
==============
There are two configurations of the Microchip PIC32MZ Embedded Connectivity
(EC) Starter Kit:
1) The PIC32MZ Embedded Connectivity Starter Kit based on the
PIC32MZ2048ECH144-I/PH chip (DM320006), and
2) The PIC32MZ Embedded Connectivity Starter Kit based on the
PIC32MZ2048ECM144-I/PH w/Crypto Engine (DM320006-C)
See www.microchip.com for further information.
Key features of the PIC32MZ Starter Kit include;
* On-board crystal or oscillator for precision microcontroller clocking
(24 MHz).
* 32 kHz oscillator for RTCC and Timer1 (optional).
* Three push button switches for user-defined inputs.
* Three user-defined indicator LEDs.
* USB Type A receptacle connectivity for PIC32 host-based applications.
* USB Type micro-AB receptacle for OTG and USB device connectivity for
PIC32 OTG/device-based applications.
* Daughter board connectors for flexible Ethernet PHY options.
* 50 MHz Ethernet PHY oscillator.
* External 4 GB SQI memory for expanded memory applications.
* PIC24FJ256GB106 USB microcontroller for on-board debugging.
* USB connectivity for on-board debugger communications.
* Regulated +3.3V power supply for powering the starter kit through USB or
expansion board.
* Connector for various expansion boards.
The PIC32MZ starter kit comes complete with a LAN8740 PHY daughter board.
Testing was performed with the following additional hardware:
- Microchip PIC32MZ Embedded Connectivity (EC) Adapter Board (AC320006)
that allows connection of the PIC32MZEC Starter Kit to the Microchip
Multimedia Expansion Board (MEB, DM320005) or PIC32 I/O Expansion Board
(DM320002). These were previously used with the PIC32MX bringup.
- Microchip Multimedia Expansion Board II (MEB II, DM320005-2).
On Board Debug Support
======================
The starter kit includes a PIC24FJ256GB106 USB microcontroller that
provides debugger connectivity over USB. The PIC24FJ256GB106 is hard-wired
to the PIC32 device to provide protocol translation through the I/O pins
of the PIC24FJ256GB106 to the ICSP<53> pins of the PIC32 device.
If MPLAB<41> REAL ICE<43> or MPLAB ICD 3 is used with the starter kit,
disconnect the onboard debugger from the PIC32 device by removing the
jumper JP2. When the on-board debugger is required, replace the jumper
JP2. When the jumper JP2 is installed, pin 1 must be connected to pin 3
and pin 2 must be connected to pin 4.
Creating Compatible NuttX HEX files
===================================
Intel Hex Format Files:
-----------------------
When NuttX is built it will produce two files in the top-level NuttX
directory:
1) nuttx - This is an ELF file, and
2) nuttx.hex - This is an Intel Hex format file. This is controlled by
the setting CONFIG_INTELHEX_BINARY in the .config file.
The PICkit tool wants an Intel Hex format file to burn into FLASH. However,
there is a problem with the generated nutt.hex: The tool expects the nuttx.hex
file to contain physical addresses. But the nuttx.hex file generated from the
top-level make will have address in the KSEG0 and KSEG1 regions.
tools/pic32mx/mkpichex:
----------------------
There is a simple tool in the NuttX tools/pic32mx directory that can be
used to solve both issues with the nuttx.hex file. But, first, you must
build the tool:
cd tools/pic32mx
make
Now you will have an excecutable file call mkpichex (or mkpichex.exe on
Cygwin). This program will take the nutt.hex file as an input, it will
convert all of the KSEG0 and KSEG1 addresses to physical address, and
it will write the modified file, replacing the original nuttx.hex.
To use this file, you need to do the following things:
export PATH=??? # Add the NuttX tools/pic32mx directory to your
# PATH variable
make # Build nuttx and nuttx.hex
mkpichex $PWD # Convert addresses in nuttx.hex. $PWD is the path
# to the top-level build directory. It is the only
# required input to mkpichex.
Tool Issues
===========
Pinquino Toolchain
------------------
If you use the Pinguino toolchain, you will probably see this error:
C:\pinguino-11\compilers\p32\bin\p32-ld.exe: target elf32-tradlittlemips not found
This is due to linker differences in the toolchains. The linker script
at configs/pic32mz-starterkit has:
OUTPUT_FORMAT("elf32-tradlittlemips")
This error can be eliminated with the Pinguino toolchain by changing this to:
OUTPUT_FORMAT("elf32-littlemips")
Mentor Toolchain
----------------
https://sourcery.mentor.com/GNUToolchain/release2934 tools.
If you use this toolchain, you will need to add CROSSDEV=mips-sde-elf- to
your Make.defs file.
ICD3
----
The onboard debugger is Slow and one is better off using an ICD3. By removing
jumper JP2, I can disable the on-board OpenHCD debugger an enable the RJ11
debug connector. My ICD 3 does seems to work properly using this configuration,
at least in the sense that it is recognized by both MPLABX IDE and IPE.
Segger J-Link
-------------
If using a Jlink that only these versions work with PIC32:
J-Link BASE / EDU V9 or later
J-Link ULTRA+ / PRO V4 or later
Oddly, you must use the G version in the command:
JLinkGDBServer -device PIC32MZ2048ECG144 -if 2-wire-JTAG-PIC32 -speed 12000
Even though we have PIC32MZ2048ECM144 parts on our board. (JLinkGDBServer
will except anything and just mess up your weekend)
Serial Console
==============
MEB-II
------
By default, the UART1 is configured for the pins used by the MEB-II
board. The UART1 signals are available at the MEB-II PICTail
connector:
--------------- --------- -------------- ------------
PIC32MZ PIN CONNECTOR MEB-II PIN PICTAIL PIN
FUNCTION J1 NAME J2
--------------- --------- -------------- ------------
RPA14/SCL1/RA14 124 SCL1/TOUCH_SCL 4
RPA15/SDA1/RA15 126 SDA1/TOUCH_SDA 6
+3.3V 1,26
GND 28
--------------- --------- -------------- ------------
This pin selection is controlled by these definitions in
pic32mz-starterkit/include/board.h:
#define BOARD_U1RX_PPS U1RXR_RPA14
#define BOARD_U1TX_PPS U1TX_RPA15R
PIC32MX I/O Expansion Board with Adapter Board
------------------------------------------
If the MEB-II UART configuration when used with the I/O Expansion board
(with the adapter), then UART will be on J11 with Pin 35 being U1RX (into
MZ) and Pin 37 being TU1X (out od MZ).
Directly from the Adapter Board
-------------------------------
But you can get serial port directly from the PIC32MZ Embedded
Connectivity (EC) Adapter Board (AC320006). The Microchip
adapter board brings out UART signals as follows:
JP7 redirects J1 U3_TX to either J2 SOSCO/RC14 or U1_TX:
Adapter
-----------------------------------------------------------------------
JP7, Pin 1: J2 Pin 32, SOSCO/RC14
Pin 2: J1 Pin 17, U3_TX
Pin 3: J2 Pin 90, U1_TX
PIC32MZ Starter Kit
-----------------------------------------------------------------------
J1 Pin 17, SOSCO/RC14 PIC32MZ SOSCO/RPC14/T1CK/RC14
RPC14 supports U1RX, U4RX, and U3TX
JP8 redirects J1 RB3/AN3/SDO4/WIFI_SDI to either J2 AN3/SDO4/WIFI_SDI or U3_RX:
Adapter PIC32MZ Starter Kit
---------------------------------------------- -------------------------
JP8, Pin 1: J2, Pin 66, AN3/SDO4/WIFI_SDI
Pin 2: J1, Pin 105, RB3/AN3/SDO4/WIFI_SDI
Pin 3: J2, Pin 88, U3_RX
PIC32MZ Starter Kit
-----------------------------------------------------------------------
J1, Pin 105, AN3/C2INA/RPB3/RB3
RPB3 supports U3RX, U1TX, and U5TX
Thus UART1 or UART3 could be used as a serial console if only the
PIC32MZEC Adapter Board is connected.
The default serial configuration here in these configurations is UART1
using RPC14 and RPB3. That UART selection can be change by running 'make
menuconfig'. The UART pin selections would need to be changed by editing
configs/pc32mz-starterkit/include/board.h.
If using a AC320006 by itself, JP7 pin 2 and JP8 pin 2 is where you would
connect a 3.3 Volt TTL serial interface.
For a configuration using UART1 connect:
TX to AC320006-JP7 pin 2 which is PIC32MZ pin 106 (RPC14) used as U1RX
RX to AC320006-JP8 pin 2 which is PIC32MZ pin 31 (RPB3)) used as U1TX
For a configuration using For UART3 connect:
TX to AC320006-JP8 pin 2 which is PIC32MZ pin 31 (RPB3)) used as U3RX
RX to AC320006-JP7 pin 2 which is PIC32MZ pin 106 (RPC14) used as U3TX
If using a AC320006 plugged into a DM320002 then regardless of which UART,
UART1 or UART3 is configured in software, the jumpers on the AC320006 are
the same, just the signal directions and UART changes.
UART1 UART3
AC320006-JP7 connect pin 2 to pin 3. U1RX U3TX
AC320006-JP8 connect pin 2 to pin 3. U1TX U3RX
For the default configuration using UART1 the PIC32MZ pin 106 (RPC14)
will be configured as U1RX and is tied to the AC320006's JP7 Pin 2.
With the jumpers as listed above, once the AC320006 is plugged into
the DM320002, the PIC32MZ U1RX will be connected to the DM320002's
J11 pin 43. The DM320002's J11 pin 43 should then be connected to
the TX of a 3.3 volt TTL serial converter such as a FTDI TTL232RG.
For the FTDI TTL232RG TX is the orange wire.
Likewise the PIC32MZ pin 31 (RPB3) will be configured as U1TX and
is tied to the AC320006's JP8 Pin 2. With the jumpers as listed above,
once the AC320006 is plugged into the DM320002, the PIC32MZ' U1TX will
be connected to the DM320002's J11 pin 41. The DM320002's J11 pin 41
should then be connected to the RX signal of a 3.3 volt TTL serial
converter. For the FTDI TTL232RG RX is the yellow wire.
For the alternate configuration using UART3 the PIC32MZ pin 106 (RPC14)
will be configured as U3TX and is tied to the AC320006's JP7 Pin 2.
With the jumpers as listed above, once the AC320006 is plugged into
the DM320002, the PIC32MZ U3TX will be connected to the DM320002's
J11 pin 43. The DM320002's J11 pin 43 should then be connected to
the RX of a 3.3 volt TTL serial converter such as a FTDI TTL232RG.
For the FTDI TTL232RG TX is the yellow wire.
Likewise the PIC32MZ pin 31 (RPB3) will be configured as U3RX and
is tied to the AC320006's JP8 Pin 2. With the jumpers as listed above,
once the AC320006 is plugged into the DM320002, the PIC32MZ' U3RX will
be connected to the DM320002's J11 pin 41. The DM320002's J11 pin 41
should then be connected to the TX signal of a 3.3 volt TTL serial
converter. For the FTDI TTL232RG RX is the orange wire.
board.h Header File Changes
---------------------------
The board configuration is currently set up to use the Serial console
on the MEB-II board. If you want to use the adapter board directly,
you willneed to change pic32mz-starterkit/include/board.h as follows:
-#define BOARD_U1RX_PPS U1RXR_RPA14
-#define BOARD_U1TX_PPS U1TX_RPA15R
+#define BOARD_U1RX_PPS U1RXR_RPC14
+#define BOARD_U1TX_PPS U1TX_RPB3R
LEDs and Buttons
================
LEDs
----
The PIC32MZ Ethernet Starter kit has 3 user LEDs labelled LED1-3 on the
board:
PIN LED Notes
--- ----- -------------------------
RH0 LED1 High illuminates (RED)
RH1 LED3 High illuminates (YELLOW)
RH2 LED2 High illuminates (GREEN)
If CONFIG_ARCH_LEDS is defined, then NuttX will control these LEDs as
follows:
ON OFF
------------------------- ---- ---- ---- ---- ---- ----
LED1 LED2 LED3 LED1 LED2 LED3
------------------------- ---- ---- ---- ---- ---- ----
LED_STARTED 0 OFF OFF OFF --- --- ---
LED_HEAPALLOCATE 1 ON OFF N/C --- --- ---
LED_IRQSENABLED 2 OFF ON N/C --- --- ---
LED_STACKCREATED 3 ON ON N/C --- --- ---
LED_INIRQ 4 N/C N/C ON N/C N/C OFF
LED_SIGNAL 4 N/C N/C ON N/C N/C OFF
LED_ASSERTION 4 N/C N/C ON N/C N/C OFF
LED_PANIC 5 ON N/C N/C OFF N/C N/C
Buttons
-------
The PIC32MZ Ethernet Starter kit has 3 user push buttons labelled SW1-3 on
the board:
PIN LED Notes
---- ---- -------------------------
RB12 SW1 Active-low
RB13 SW2 Active-low
RB14 SW3 Active-low
The switches do not have any debounce circuitry and require internal pull-
up resistors. When Idle, the switches are pulled high (+3.3V), and they
are grounded when pressed.
Configurations
==============
Information Common to All Configurations
----------------------------------------
Each PIC32MZ configuration is maintained in a sub-directory and can be
selected as follow:
tools/configure.sh [OPTIONS] pic32mz-starterkit/<subdir>
Where typical options are -l to configure to build on Linux or -c to
configure for Cygwin under Linux. 'tools/configure.sh -h' will show
you all of the options.
Before building, make sure the PATH environment variable includes the
correct path to the directory than holds your toolchain binaries.
And then build NuttX by simply typing the following. At the conclusion of
the make, the nuttx binary will reside in an ELF file called, simply,
nuttx.
make
The <subdir> that is provided above as an argument to the tools/configure.sh
must be is one of the following.
Configuration Directories
-------------------------
nsh:
This is the NuttShell (NSH) using the NSH startup logic at
apps/examples/nsh.
NOTES:
1. This configuration uses the mconf-based configuration tool. To
change this configurations using that tool, you should:
a. Build and install the kconfig-mconf tool. See nuttx/README.txt
see additional README.txt files in the NuttX tools repository.
b. Execute 'make menuconfig' in nuttx/ in order to start the
reconfiguration process.
2. Serial Output
The OS test produces all of its test output on the serial console.
This configuration has UART1 enabled as a serial console. This
can easily be changed by reconfiguring with 'make menuconfig'.
3. Toolchain
By default, the Pinguino MIPs tool chain is used. This toolchain
selection can easily be changed with 'make menuconfig'.
4. Default configuration: These are other things that you may want to
change in the configuration:
CONFIG_ARCH_CHIP_PIC32MZ2048ECM=y : Assumes part with Crypto Engine
CONFIG_PIC32MZ_DEBUGGER_ENABLE=n : Debugger is disabled
CONFIG_PIC32MZ_TRACE_ENABLE=n : Trace is disabled
CONFIG_PIC32MZ_JTAG_ENABLE=n : JTAG is disabled
7d4451ee86