nuttx

chip

arch/arm/src/sam34: This commit removes support for the dedicated vector handling from the SAM3/4 architecture support. Only common vectors are now supported.

2018-06-19 18:13:15 -06:00

chip.h

arch/arm/src/sam34: This commit removes support for the dedicated vector handling from the SAM3/4 architecture support. Only common vectors are now supported.

2018-06-19 18:13:15 -06:00

Kconfig

All network drivers! Change pre-processor logic that selects the high priority work queue or gives preferential treatment to the high priority work. All network logic must run on the low priority work queue! Or suffer the consequences.

2018-11-21 07:57:26 -06:00

Make.defs

arch/arm/src/armv7-m/up_trigger_irq.c: Add logic to trigger ARMv7-M interrupts and exceptions.

2018-08-25 10:23:21 -06:00

sam3u_gpio.h

…

sam3u_periphclks.h

…

sam3x_gpio.h

…

sam3x_periphclks.h

…

sam4cm_cpuidlestack.c

Make sure that labeling is used consistently in all function headers.

2018-02-01 10:00:02 -06:00

sam4cm_cpuindex.c

SAM3/4: Add SMP support for the dual-core SAM4CM

2016-12-04 07:23:31 -06:00

sam4cm_cpupause.c

irq_dispatch: Add argument pointer to irq_dispatch

2017-02-27 06:27:56 -06:00

sam4cm_cpustart.c

arch/: Remove dangling space at the end of lines.

2017-06-28 13:16:48 -06:00

sam4cm_freerun.c

…

sam4cm_freerun.h

…

sam4cm_gpio.h

…

sam4cm_idle.c

SAM3/4: Add SMP support for the dual-core SAM4CM

2016-12-04 07:23:31 -06:00

sam4cm_oneshot_lowerhalf.c

…

sam4cm_oneshot.c

Fix lots of occurrences of 'the the', 'the there', 'the these', 'the then', 'the they.

2017-05-11 13:35:56 -06:00

sam4cm_oneshot.h

…

sam4cm_periphclks.h

…

sam4cm_supc.c

…

sam4cm_supc.h

…

sam4cm_tc.c

Squashed commit of the following:

2017-10-04 15:22:27 -06:00

sam4cm_tc.h

…

sam4cm_tickless.c

Replace non critical PANIC with DEBUGPANIC to save the code space

2018-08-24 06:21:15 -06:00

sam4e_gpio.h

…

sam4e_periphclks.h

…

sam4l_clockconfig.c

…

sam4l_gpio.c

…

sam4l_gpio.h

…

sam4l_periphclks.c

…

sam4l_periphclks.h

…

sam4s_gpio.h

SAM3/4: GPIO bit numbering typo fixes.

2017-02-26 09:54:04 -08:00

sam4s_periphclks.h

…

sam_aes.c

Squashed commit of the following:

2017-10-04 15:22:27 -06:00

sam_aes.h

…

sam_allocateheap.c

arch/: Fix an error found in build testing. The protoype of mpu_log2regionfloor() changed; an additional parameter was added. However, none of the calls to mpu_log2regionfloor() were updated to pass the new, additional parameter.

2018-08-24 16:40:37 -06:00

sam_clockconfig.c

…

sam_clockconfig.h

…

sam_cmcc.c

…

sam_cmcc.h

…

sam_dmac.c

arch/arm/src/max326xx: Add framework for MAX326XX standard DMA support.

2018-11-20 08:09:03 -06:00

sam_dmac.h

…

sam_emac.c

All network drivers! Change pre-processor logic that selects the high priority work queue or gives preferential treatment to the high priority work. All network logic must run on the low priority work queue! Or suffer the consequences.

2018-11-21 07:57:26 -06:00

sam_emac.h

Standardization of some function headers.

2018-03-13 09:52:27 -06:00

sam_gpio.c

SAM GPIO: Apply Wolfgang's change for SAM3/4 to SAMA5 and SAMV7

2016-09-20 15:33:31 -06:00

sam_gpio.h

…

sam_gpioirq.c

irq_dispatch: Add argument pointer to irq_dispatch

2017-02-27 06:27:56 -06:00

sam_hsmci.c

Fix lots of typos in C comments and Kconfig help text

2018-07-08 18:24:45 -06:00

sam_hsmci.h

Make sure that labeling is used consistently in all function headers.

2018-02-01 10:00:02 -06:00

sam_irq.c

arch/arm/src: Correct all ARMv7-M architectures. Interrupts were not be disabled correctly on power up. Writing zero to the NVIC SET-ENABLE registers has no effect. In order to disable interrupts, it is necessary to write all ones to the NVIC CLEAR-ENABLE register. Noted by David Sidrane.

2018-09-21 21:32:50 -06:00

sam_lowputc.c

…

sam_lowputc.h

…

sam_mpuinit.c

…

sam_mpuinit.h

…

sam_periphclks.h

…

sam_rtc.c

irq_dispatch: Add argument pointer to irq_dispatch

2017-02-27 06:27:56 -06:00

sam_rtc.h

…

sam_rtt.c

Make sure that labeling is used consistently in all function headers.

2018-02-01 10:00:02 -06:00

sam_rtt.h

Make sure that labeling is used consistently in all function headers.

2018-02-01 10:00:02 -06:00

sam_serial.c

Convert remaining serial drivers to use use irq_attach.

2017-02-27 10:27:14 -06:00

sam_spi.c

Trivial update to some comments.

2018-02-12 14:46:40 -06:00

sam_spi.h

Make sure that labeling is used consistently in all function headers.

2018-02-01 10:00:02 -06:00

sam_start.c

Squashed commit of the following:

2018-06-20 08:18:32 -06:00

sam_start.h

arch/arm/src/sam34: This commit removes support for the dedicated vector handling from the SAM3/4 architecture support. Only common vectors are now supported.

2018-06-19 18:13:15 -06:00

sam_tc.c

Replace all ASSERT with DEBUGASSERT to save the code space

2018-08-24 06:58:30 -06:00

sam_tc.h

Make sure that labeling is used consistently in all function headers.

2018-02-01 10:00:02 -06:00

sam_timerisr.c

configs/olimex-stm32-p407/dhtxx: Fix defconfig file. It was based on an older, incompatible version of NuttX.

2018-09-03 09:42:04 -06:00

sam_twi.c

sched/wdog: wd_start() is an internal OS function and should not set the errno value. Reviewed and updated every call to wd_start() to verify if return value is used and if so if the errno value is accessed.

2018-01-31 10:09:14 -06:00

sam_twi.h

Make sure that labeling is used consistently in all function headers.

2018-02-01 10:00:02 -06:00

sam_udp.c

Make sure that labeling is used consistently in all function headers (part 2).

2018-02-01 12:03:55 -06:00

sam_udp.h

…

sam_userspace.c

…

sam_userspace.h

…

sam_wdt.c

Replace all ASSERT with DEBUGASSERT to save the code space

2018-08-24 06:58:30 -06:00

sam_wdt.h

Make sure that labeling is used consistently in all function headers.

2018-02-01 10:00:02 -06:00