a1c991d921
Move boards to boards folder
* boards: rename configs folder to boards
This is the proposed layout after the change:
boards: - folder containing board folders
<board>: - name of each board
drivers: - extra drivers specific for platform
include: - header files for the boars
scripts: - extra scripts specific for platform
src: - board specific code
tools: - extra tools specific for platform
<config>: - board specific configuration(s)
Note:
<xxx> names are dependent on platform
This is a logical change to aim to the arch layout but this is a
huge change it should be done in several steps to lower the risk.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Kconfig: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Makefile: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Makefile.*: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* Make.defs: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .sh: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .mk: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .c & .h: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* .bat: replace configs with boards
The change is needed after the path change
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
103 lines
3.0 KiB
Plaintext
103 lines
3.0 KiB
Plaintext
README
|
|
======
|
|
|
|
This is the README file for the port of NuttX to the Arduino Mega 2560 Rev3.
|
|
|
|
https://www.arduino.cc/en/Main/ArduinoBoardMega2560
|
|
|
|
The board is based on ATMega2560 chip from Atmel
|
|
|
|
http://www.atmel.com/devices/atmega2560.aspx
|
|
|
|
Contents
|
|
========
|
|
|
|
o Toolchain
|
|
o Serial Console
|
|
o Configurations
|
|
|
|
Toolchain
|
|
=========
|
|
|
|
Right now only Atmel's AVR8 Toolchain is supported. You can get it from
|
|
|
|
http://www.atmel.com/tools/atmelavrtoolchainforwindows.aspx
|
|
|
|
It is basically WinAVR compatible so sub-projects may define WinAVR as a
|
|
tool-chain but specify path to the Atmel AVR8 in path. See
|
|
arduino-mega2560/hello for example.
|
|
|
|
Serial Console
|
|
==============
|
|
|
|
The serial console is available on USART0. You will need to connect an
|
|
RS-232 shield or an external RS-232 driver as follows:
|
|
|
|
TXD: TX0->1
|
|
RXD: RX0->0
|
|
GND: Power GND
|
|
+5V: Power +5V
|
|
|
|
You will then need to use a terminal program configured at 38400 8N1.
|
|
|
|
Configurations
|
|
==============
|
|
|
|
Common Configuration Notes
|
|
--------------------------
|
|
1. Each Arduino MEGA2560 configuration is maintained in a sub-directory
|
|
and can be selected as follow:
|
|
|
|
tools/configure.sh arduino-mega2560/<subdir>
|
|
|
|
Where <subdir> is one of the configuration sub-directories described in
|
|
the following paragraph.
|
|
|
|
2. These configurations use the mconf-based configuration tool. To
|
|
change a configurations using that tool, you should:
|
|
|
|
a. Build and install the kconfig-mconf tool. See nuttx/README.txt
|
|
see additional README.txt files in the NuttX tools repository.
|
|
|
|
b. Execute 'make menuconfig' in nuttx/ in order to start the
|
|
reconfiguration process.
|
|
|
|
3. By default, all configurations assume the Atmel Studio AVR8 toolchain
|
|
under Cygwin with Windows. This is easily reconfigured:
|
|
|
|
CONFIG_HOST_WINDOWS=y
|
|
CONFIG_WINDOWS_CYGWIN=y
|
|
CONFIG_AVR_BUILDROOT_TOOLCHAIN=y
|
|
|
|
Configuration Sub-Directories
|
|
-----------------------------
|
|
hello:
|
|
The simple apps/examples/hello "Hello, World!" example.
|
|
|
|
nsh:
|
|
This is a reduce NuttShell (NSH) configuration using apps/example/nsh.
|
|
The serial console is provided on USART0 and can be accessed via
|
|
an external RS-232 driver as described above under "Serial Console".
|
|
|
|
NOTES:
|
|
|
|
1. As of 2015-01-16, the default static memory usage is:
|
|
|
|
$ size nuttx.elf
|
|
text data bss dec hex filename
|
|
34348 2117 944 37409 9221 nuttx.elf
|
|
|
|
And dynamic, heap usage:
|
|
|
|
nsh> free
|
|
total used free largest
|
|
Mem: 4736 1768 2968 2968
|
|
|
|
There is plenty of FLASH space but not a lot of free SRAM. This
|
|
SRAM usage is due primarily to constant strings defined by NSH.
|
|
|
|
NOTE: I investigated the possibility of adding IPTR/IOBJ
|
|
qualifiers in the NSH library and moving the strings to FLASH.
|
|
This is still a possibility but would requires some extensive
|
|
changes to NSH.
|