f8e5fa6eb4
git-svn-id: svn://svn.code.sf.net/p/nuttx/code/trunk@981 42af7a65-404d-4744-a932-0658087f49c3
198 lines
6.6 KiB
Plaintext
198 lines
6.6 KiB
Plaintext
README
|
|
^^^^^^
|
|
|
|
Tools
|
|
^^^^^
|
|
|
|
I use the lpc21isp tool to load NuttX into FLASH. That tool is available
|
|
in the files section at http://tech.groups.yahoo.com/group/lpc21isp/. In
|
|
order version 1.60 of lpc21isp for Linux, I had to make several changes.
|
|
This changes are shown in lpc21ips-1.60.diff.
|
|
|
|
I use the script lpc21isp.sh to perform the actual download. You will
|
|
probably have to make some changes to this script in order to use it.
|
|
For example, the path to the built lpc21isp binary will most likely
|
|
have to have change. Then move this script to the top level NuttX
|
|
directory and simply execute it to load NuttX onto the board.
|
|
|
|
ARM/LPC214X-specific Configuration Options
|
|
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
CONFIG_ARCH - Identifies the arch/ subdirectory. This should
|
|
be set to:
|
|
|
|
CONFIG_ARCH=arm
|
|
|
|
CONFIG_ARCH_name - For use in C code:
|
|
|
|
CONFIG_ARCH_ARM=y
|
|
|
|
CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
|
|
|
|
CONFIG_ARCH_CHIP=c5471
|
|
|
|
CONFIG_ARCH_CHIP_name - For use in C code
|
|
|
|
CONFIG_ARCH_CHIP_C5471
|
|
|
|
CONFIG_ARCH_BOARD - Identifies the configs subdirectory and
|
|
hence, the board that supports the particular chip or SoC.
|
|
|
|
CONFIG_ARCH_BOARD=c5471evm (for the Spectrum Digital C5471 EVM)
|
|
|
|
CONFIG_ARCH_BOARD_name - For use in C code
|
|
|
|
CONFIG_ARCH_BOARD_C5471EVM (for the Spectrum Digital C5471 EVM)
|
|
|
|
CONFIG_ARCH_LOOPSPERMSEC - Must be calibrated for correct operation
|
|
of delay loops
|
|
|
|
CONFIG_ENDIAN_BIG - define if big endian (default is little
|
|
endian)
|
|
|
|
CONFIG_DRAM_SIZE - Describes the installed DRAM.
|
|
|
|
CONFIG_DRAM_START - The start address of installed DRAM
|
|
|
|
CONFIG_DRAM_END - Should be (CONFIG_DRAM_START+CONFIG_DRAM_SIZE)
|
|
|
|
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to boards that
|
|
have LEDs
|
|
|
|
CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
|
|
stack. If defined, this symbol is the size of the interrupt
|
|
stack in bytes. If not defined, the user task stacks will be
|
|
used during interrupt handling.
|
|
|
|
CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
|
|
|
|
LPC2148 specific chip initialization
|
|
|
|
CONFIG_EXTMEM_MODE, CONFIG_RAM_MODE, CONFIG_CODE_BASE, CONFIG_PLL_SETUP,
|
|
CONFIG_MAM_SETUP, CONFIG_APBDIV_SETUP, CONFIG_EMC_SETUP, CONFIG_BCFG0_SETUP,
|
|
CONFIG_BCFG1_SETUP, CONFIG_BCFG2_SETUP, CONFIG_BCFG3_SETUP, CONFIG_ADC_SETUP
|
|
|
|
LPC214X specific device driver settings
|
|
|
|
CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the
|
|
console and ttys0 (default is the UART0).
|
|
|
|
CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received.
|
|
This specific the size of the receive buffer
|
|
|
|
CONFIG_UARTn_TXBUFSIZE - Characters are buffered before
|
|
being sent. This specific the size of the transmit buffer
|
|
|
|
CONFIG_UARTn_BAUD - The configure BAUD of the UART.
|
|
|
|
CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8.
|
|
|
|
CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity, 3=mark 1, 4=space 0
|
|
|
|
CONFIG_UARTn_2STOP - Two stop bits
|
|
|
|
LPC214X USB Configuration
|
|
|
|
CONFIG_LPC214X_USBDEV_FRAME_INTERRUPT
|
|
Handle USB Start-Of-Frame events.
|
|
Enable reading SOF from interrupt handler vs. simply reading on demand.
|
|
Probably a bad idea... Unless there is some issue with sampling the SOF
|
|
from hardware asynchronously.
|
|
|
|
CONFIG_LPC214X_USBDEV_EPFAST_INTERRUPT
|
|
Enable high priority interrupts. I have no idea why you might want to
|
|
do that
|
|
|
|
CONFIG_LPC214X_USBDEV_NDMADESCRIPTORS
|
|
Number of DMA descriptors to allocate in the 8Kb USB RAM. This is a
|
|
tradeoff between the number of DMA channels that can be supported vs
|
|
the size of the DMA buffers available.
|
|
|
|
CONFIG_LPC214X_USBDEV_DMA
|
|
Enable lpc214x-specific DMA support
|
|
|
|
Configurations
|
|
^^^^^^^^^^^^^^
|
|
|
|
Each NXP LPC214x configuration is maintained in a sudirectory and
|
|
can be selected as follow:
|
|
|
|
cd tools
|
|
./configure.sh mcu123-lpc214x/<subdir>
|
|
cd -
|
|
. ./setenv.sh
|
|
|
|
Where <subdir> is one of the following:
|
|
|
|
ostest
|
|
^^^^^^
|
|
|
|
This configuration directory, performs a simple OS test using
|
|
examples/ostest.
|
|
|
|
nsh
|
|
^^^
|
|
|
|
Configures the NuttShell (nsh) located at examples/nsh. The
|
|
Configuration enables only the serial NSH interfaces.
|
|
|
|
Configuration Options
|
|
^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
In additional to the common configuration options listed in the
|
|
file configs/README.txt, there are other configuration options
|
|
specific to the LPC214x:
|
|
|
|
CONFIG_ARCH - identifies the arch subdirectory and, hence, the
|
|
processor architecture.
|
|
CONFIG_ARCH_name - for use in C code. This identifies the
|
|
particular chip or SoC that the architecture is implemented
|
|
in.
|
|
CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
|
|
CONFIG_ARCH_CHIP_name - For use in C code
|
|
CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence,
|
|
the board that supports the particular chip or SoC.
|
|
CONFIG_ENDIAN_BIG - define if big endian (default is little endian)
|
|
CONFIG_ARCH_BOARD_name - for use in C code
|
|
CONFIG_BOARD_LOOPSPERMSEC - for delay loops
|
|
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to lpc2148.
|
|
CONFIG_DRAM_SIZE - Describes the internal DRAM.
|
|
CONFIG_DRAM_START - The start address of internal DRAM
|
|
CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
|
|
|
|
LPC2148 specific chip initialization
|
|
|
|
CONFIG_EXTMEM_MODE, CONFIG_RAM_MODE. CONFIG_CODE_BASE, CONFIG_PLL_SETUP,
|
|
CONFIG_MAM_SETUP, CONFIG_APBDIV_SETUP, CONFIG_EMC_SETUP,. CONFIG_BCFG0_SETUP,
|
|
CONFIG_BCFG1_SETUP, CONFIG_BCFG2_SETUP, CONFIG_BCFG3_SETUP, CONFIG_ADC_SETUP
|
|
|
|
LPC214X UART device driver settings
|
|
|
|
CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the
|
|
console and ttys0 (default is the UART0).
|
|
CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received.
|
|
This specific the size of the receive buffer
|
|
CONFIG_UARTn_TXBUFSIZE - Characters are buffered before
|
|
being sent. This specific the size of the transmit buffer
|
|
CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be
|
|
CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8.
|
|
CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity, 3=mark 1, 4=space 0
|
|
CONFIG_UARTn_2STOP - Two stop bits
|
|
|
|
LPC214X USB Configuration
|
|
|
|
CONFIG_LPC214X_USBDEV_FRAME_INTERRUPT
|
|
Handle USB Start-Of-Frame events.
|
|
Enable reading SOF from interrupt handler vs. simply reading on demand.
|
|
Probably a bad idea... Unless there is some issue with sampling the SOF
|
|
from hardware asynchronously.
|
|
CONFIG_LPC214X_USBDEV_EPFAST_INTERRUPT
|
|
Enable high priority interrupts. I have no idea why you might want to
|
|
do that
|
|
CONFIG_LPC214X_USBDEV_NDMADESCRIPTORS
|
|
Number of DMA descriptors to allocate in the 8Kb USB RAM. This is a
|
|
tradeoff between the number of DMA channels that can be supported vs
|
|
the size of the DMA buffers available.
|
|
CONFIG_LPC214X_USBDEV_DMA
|
|
Enable lpc214x-specific DMA support
|