zp214xpa README FILE
====================
The ZP213X/4XPA board from the0.net with LPC2148 installed.
Includes support for the UG-2864AMBAG01 OLED from The0.net.
Contents
========
o MCU Connections
o Serial Console
o Configurations
MCU Connections:
================
Module Socket:
--------------
PIN NAME PIN NAME
1 VBAT 56 VCC
2 3V3 55 Vusb
3 VREF 54 3V3
4 P0.0 53 RESET
5 P0.1 52 P1.31
6 P0.2 51 P1.30
7 P0.3 50 P1.29
8 P0.4 49 P1.28
9 P0.5 48 P1.27
10 P0.6 47 P1.26
11 P0.7 46 P1.25
12 P0.8 45 P1.24
13 P0.9 44 P1.23
14 P0.10 43 P1.22
15 P0.11 42 P1.21
16 P0.12 41 P1.20
17 P0.13 40 P1.19
18 P0.14 39 P1.18
19 P0.15 38 P1.17
20 P0.16 37 P1.16
21 P0.17 36 P0.31
22 P0.18 35 P0.30
23 P0.19 34 P0.29
24 P0.20 33 P0.28
25 P0.21 32 P0.27
26 P0.22 31 P0.26
27 P0.23 30 P0.25
28 GND 29 GND
JTAG Debug:
-----------
PIN NAME PIN NAME
1 VCC1 2 3V3
3 P1.31 NTRST 4 GND
5 P1.28 TDI 6 GND
7 P1.30 TMS 8 GND
9 P1.29 TCK 10 GND
11 P1.26 RTCK 12 GND
13 P1.27 TDO 14 GND
15 RESET NRTS 16 GND
17 N/C NC0 18 GND
19 N/C NC1 20 GND
Z28160 Net Module:
------------------
PIN NAME PIN NAME
1 P0.7 /CS 10 3V3 VCC
2 P0.4 SCK 9 P1.24 RST
3 P0.6 SI 8 N/C CLKOUT
4 P0.5 SO 7 INT P1.25
5 GND 6 N/C WOL
SPI LCD:
--------
PIN NAME
1 3V3 3V3
2 VCC 5V
3 P0.18 RESET(DO)
4 P0.19 DI
5 P0.20 CS
6 P0.17 SCK
7 P0.23 A0(RESET)
8 N/C LED-
9 N/C LED+(BL)
10 GND GND
USB Interface:
--------------
Vusb, P0.26, P0.27
Serial Console:
===============
Both UART0 and UART1 are always enabled. UART0 is configured to be the
serial console in these configurations.
P0.0/TXD0/PWM1 Module Socket, Pin 4
P0.1/RxD0/PWM3/EINT0 Module Socket, Pin 5
P0.8/TXD1/PWM4/AD1.1 Module Socket, Pin 12
P0.9/RxD1/PWM6/EINT3 Module Socket, Pin 13
Configurations:
===============
Each NXP LPC214x configuration is maintained in a sudirectory and
can be selected as follow:
cd tools
./configure.sh zp214xpa/<subdir>
cd -
. ./setenv.sh
Where <subdir> is one of the following:
nsh:
----
Configures the NuttShell (nsh) located at examples/nsh. The
Configuration enables only the serial NSH interfaces.
NOTES:
1. This configuration uses the mconf-based configuration tool. To
change this configuration using that tool, you should:
a. Build and install the mconf tool. See nuttx/README.txt and
misc/tools/
b. Execute 'make menuconfig' in nuttx/ in order to start the
reconfiguration process.
2. Default platform/toolchain:
CONFIG_HOST_LINUX=y : Windows
CONFIG_ARM_TOOLCHAIN_GNU_EABI=y : Buildroot (arm-nuttx-elf-gcc)
CONFIG_RAW_BINARY=y : Output formats: ELF and raw binary
e5614c862e