429 lines
16 KiB
C
429 lines
16 KiB
C
/****************************************************************************
|
|
* boards/arm/stm32l4/stm32l4r9ai-disco/include/stm32l4r9ai-disco-clocking.h
|
|
*
|
|
* Licensed to the Apache Software Foundation (ASF) under one or more
|
|
* contributor license agreements. See the NOTICE file distributed with
|
|
* this work for additional information regarding copyright ownership. The
|
|
* ASF licenses this file to you under the Apache License, Version 2.0 (the
|
|
* "License"); you may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at
|
|
*
|
|
* http://www.apache.org/licenses/LICENSE-2.0
|
|
*
|
|
* Unless required by applicable law or agreed to in writing, software
|
|
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
|
|
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
|
|
* License for the specific language governing permissions and limitations
|
|
* under the License.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#ifndef __BOARDS_ARM_STM32L4_STM32L4R9AI_DISCO_INCLUDE_STM32L4R9AI_DISCO_CLOCKING_H
|
|
#define __BOARDS_ARM_STM32L4_STM32L4R9AI_DISCO_INCLUDE_STM32L4R9AI_DISCO_CLOCKING_H
|
|
|
|
/****************************************************************************
|
|
* Included Files
|
|
****************************************************************************/
|
|
|
|
#include <nuttx/config.h>
|
|
#ifndef __ASSEMBLY__
|
|
# include <stdint.h>
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Pre-processor Definitions
|
|
****************************************************************************/
|
|
|
|
/* Clocking *****************************************************************/
|
|
|
|
/* The stm32l4r9ai-disco supports both HSE and LSE crystals. As shipped,
|
|
* the HSE is a 16 MHz crystal X2. Therefore the stm32l4r9ai-disco can run
|
|
* off the 16MHz HSI clock, or the MSI, or the HSE. Here we configure HSE
|
|
* to give us 120MHz system clock (maximum supported for STM32L4+ chips)
|
|
* instead of the more traditional 80MHz that is used by most STM32L4 boards
|
|
* supported by NuttX.
|
|
*/
|
|
|
|
/* HSI - 16 MHz RC factory-trimmed
|
|
* LSI - 32 KHz RC
|
|
* MSI - variable up to 48 MHz, synchronized to LSE
|
|
* HSE - 16 MHz installed
|
|
* LSE - 32.768 kHz installed
|
|
*/
|
|
|
|
#define STM32L4_HSI_FREQUENCY 16000000ul
|
|
#define STM32L4_LSI_FREQUENCY 32000
|
|
#define STM32L4_LSE_FREQUENCY 32768
|
|
#define STM32L4_HSE_FREQUENCY 16000000ul
|
|
|
|
#define STM32L4_SYSCLK_FREQUENCY 120000000ul
|
|
#define BOARD_AHB_FREQUENCY STM32L4_SYSCLK_FREQUENCY
|
|
|
|
/* Higher SYSCLK reguires more flash wait states. */
|
|
|
|
#define BOARD_FLASH_WAITSTATES 5
|
|
|
|
/* XXX there needs to be independent selections for the System Clock Mux and
|
|
* the PLL Source Mux; currently System Clock Mux always is PLL, and PLL
|
|
* Source Mux is chosen by the following define. This is probably OK in many
|
|
* cases, but should be separated to support other power configurations.
|
|
*/
|
|
|
|
#if 0
|
|
# define HSI_CLOCK_CONFIG 1 /* HSI-16 clock configuration */
|
|
#elif 1
|
|
# define HSE_CLOCK_CONFIG 1 /* HSE with 16 MHz xtal */
|
|
#else
|
|
# define MSI_CLOCK_CONFIG 1 /* MSI @ 4 MHz autotrimmed via LSE */
|
|
#endif
|
|
|
|
#if defined(HSI_CLOCK_CONFIG)
|
|
|
|
#define STM32L4_BOARD_USEHSI 1
|
|
|
|
/* Prescaler common to all PLL inputs; will be 1 */
|
|
|
|
#define STM32L4_PLLCFG_PLLM RCC_PLLCFG_PLLM(1)
|
|
|
|
/* 'main' PLL config; we use this to generate our system clock via the R
|
|
* output. We set it up as 16 MHz / 1 * 15 / 2 = 120 MHz
|
|
*
|
|
* XXX NOTE:
|
|
* currently the main PLL is implicitly turned on and is implicitly
|
|
* the system clock; this should be configurable since not all
|
|
* applications may want things done this way.
|
|
*/
|
|
|
|
#define STM32L4_PLLCFG_PLLN RCC_PLLCFG_PLLN(15)
|
|
#define STM32L4_PLLCFG_PLLP 0
|
|
#undef STM32L4_PLLCFG_PLLP_ENABLED
|
|
#define STM32L4_PLLCFG_PLLQ RCC_PLLCFG_PLLQ_2
|
|
#define STM32L4_PLLCFG_PLLQ_ENABLED
|
|
#define STM32L4_PLLCFG_PLLR RCC_PLLCFG_PLLR_2
|
|
#define STM32L4_PLLCFG_PLLR_ENABLED
|
|
|
|
/* 'SAIPLL1' is used to generate the 48 MHz clock, since we can't
|
|
* do that with the main PLL's N value. We set N = 13, and enable
|
|
* the Q output (ultimately for CLK48) with /4. So,
|
|
* 16 MHz / 1 * 12 / 4 = 48 MHz
|
|
*
|
|
* XXX NOTE: currently the SAIPLL /must/ be explicitly selected in the
|
|
* menuconfig, or else all this is a moot point, and the various 48 MHz
|
|
* peripherals will not work (RNG at present). I would suggest removing
|
|
* that option from Kconfig altogether, and simply making it an option
|
|
* that is selected via a #define here, like all these other params.
|
|
*/
|
|
|
|
#define STM32L4_PLLSAI1CFG_PLLN RCC_PLLSAI1CFG_PLLN(12)
|
|
#define STM32L4_PLLSAI1CFG_PLLP 0
|
|
#undef STM32L4_PLLSAI1CFG_PLLP_ENABLED
|
|
#define STM32L4_PLLSAI1CFG_PLLQ RCC_PLLSAI1CFG_PLLQ_4
|
|
#define STM32L4_PLLSAI1CFG_PLLQ_ENABLED
|
|
#define STM32L4_PLLSAI1CFG_PLLR 0
|
|
#undef STM32L4_PLLSAI1CFG_PLLR_ENABLED
|
|
|
|
/* 'SAIPLL2' is not used in this application */
|
|
|
|
#define STM32L4_PLLSAI2CFG_PLLN RCC_PLLSAI2CFG_PLLN(8)
|
|
#define STM32L4_PLLSAI2CFG_PLLP 0
|
|
#undef STM32L4_PLLSAI2CFG_PLLP_ENABLED
|
|
#define STM32L4_PLLSAI2CFG_PLLR 0
|
|
#undef STM32L4_PLLSAI2CFG_PLLR_ENABLED
|
|
|
|
/* CLK48 will come from PLLSAI1 (implicitly Q) */
|
|
|
|
#if defined(CONFIG_STM32L4_OTGFS) || defined(STM32L4_SDMMC) || defined(CONFIG_STM32L4_RNG)
|
|
# define STM32L4_USE_CLK48 1
|
|
# define STM32L4_CLK48_SEL RCC_CCIPR_CLK48SEL_PLLSAI1
|
|
# define STM32L4_HSI48_SYNCSRC SYNCSRC_NONE
|
|
#endif
|
|
|
|
/* Enable the LSE oscillator, used automatically trim the MSI, and for RTC */
|
|
|
|
#define STM32L4_USE_LSE 1
|
|
|
|
/* HSI16 used as I2C clock */
|
|
|
|
#define STM32L4_I2C_USE_HSI16 1
|
|
|
|
/* AHB clock (HCLK) is SYSCLK (120 MHz) */
|
|
|
|
#define STM32L4_RCC_CFGR_HPRE RCC_CFGR_HPRE_SYSCLK /* HCLK = SYSCLK / 1 */
|
|
#define STM32L4_HCLK_FREQUENCY STM32L4_SYSCLK_FREQUENCY
|
|
|
|
/* APB1 clock (PCLK1) is HCLK/1 (120 MHz) */
|
|
|
|
#define STM32L4_RCC_CFGR_PPRE1 RCC_CFGR_PPRE1_HCLK /* PCLK1 = HCLK / 1 */
|
|
#define STM32L4_PCLK1_FREQUENCY (STM32L4_HCLK_FREQUENCY / 1)
|
|
|
|
/* The timer clock frequencies are automatically defined by hardware.
|
|
* If the APB prescaler equals 1, the timer clock frequencies are set to the
|
|
* same frequency as that of the APB domain. Otherwise they are set to twice.
|
|
*
|
|
* REVISIT : this can be configured
|
|
*/
|
|
|
|
#define STM32L4_APB1_TIM2_CLKIN (STM32L4_PCLK1_FREQUENCY)
|
|
#define STM32L4_APB1_TIM3_CLKIN (STM32L4_PCLK1_FREQUENCY)
|
|
#define STM32L4_APB1_TIM4_CLKIN (STM32L4_PCLK1_FREQUENCY)
|
|
#define STM32L4_APB1_TIM5_CLKIN (STM32L4_PCLK1_FREQUENCY)
|
|
#define STM32L4_APB1_TIM6_CLKIN (STM32L4_PCLK1_FREQUENCY)
|
|
#define STM32L4_APB1_TIM7_CLKIN (STM32L4_PCLK1_FREQUENCY)
|
|
|
|
/* APB2 clock (PCLK2) is HCLK (120 MHz) */
|
|
|
|
#define STM32L4_RCC_CFGR_PPRE2 RCC_CFGR_PPRE2_HCLK /* PCLK2 = HCLK / 1 */
|
|
#define STM32L4_PCLK2_FREQUENCY (STM32L4_HCLK_FREQUENCY / 1)
|
|
|
|
/* The timer clock frequencies are automatically defined by hardware.
|
|
* If the APB prescaler equals 1, the timer clock frequencies are set to the
|
|
* same frequency as that of the APB domain. Otherwise they are set to twice.
|
|
*
|
|
* REVISIT : this can be configured
|
|
*/
|
|
|
|
#define STM32L4_APB2_TIM1_CLKIN (STM32L4_PCLK2_FREQUENCY)
|
|
#define STM32L4_APB2_TIM8_CLKIN (STM32L4_PCLK2_FREQUENCY)
|
|
|
|
#elif defined(HSE_CLOCK_CONFIG)
|
|
|
|
/* Use the HSE */
|
|
|
|
#define STM32L4_BOARD_USEHSE 1
|
|
|
|
/* Prescaler common to all PLL inputs */
|
|
|
|
#define STM32L4_PLLCFG_PLLM RCC_PLLCFG_PLLM(1)
|
|
|
|
/* 'main' PLL config; we use this to generate our system clock via the R
|
|
* output. We set it up as 16 MHz / 1 * 15 / 2 = 120 MHz
|
|
*
|
|
* XXX NOTE:
|
|
* currently the main PLL is implicitly turned on and is implicitly
|
|
* the system clock; this should be configurable since not all
|
|
* applications may want things done this way.
|
|
*/
|
|
|
|
#define STM32L4_PLLCFG_PLLN RCC_PLLCFG_PLLN(15)
|
|
#define STM32L4_PLLCFG_PLLP 0
|
|
#undef STM32L4_PLLCFG_PLLP_ENABLED
|
|
#define STM32L4_PLLCFG_PLLQ RCC_PLLCFG_PLLQ_2
|
|
#define STM32L4_PLLCFG_PLLQ_ENABLED
|
|
#define STM32L4_PLLCFG_PLLR RCC_PLLCFG_PLLR_2
|
|
#define STM32L4_PLLCFG_PLLR_ENABLED
|
|
|
|
/* 'SAIPLL1' is used to generate the 48 MHz clock, since we can't
|
|
* do that with the main PLL's N value. We set N = 12, and enable
|
|
* the Q output (ultimately for CLK48) with /4. So,
|
|
* 16 MHz / 1 * 12 / 4 = 48 MHz
|
|
*
|
|
* XXX NOTE: currently the SAIPLL /must/ be explicitly selected in the
|
|
* menuconfig, or else all this is a moot point, and the various 48 MHz
|
|
* peripherals will not work (RNG at present). I would suggest removing
|
|
* that option from Kconfig altogether, and simply making it an option
|
|
* that is selected via a #define here, like all these other params.
|
|
*/
|
|
|
|
#define STM32L4_PLLSAI1CFG_PLLN RCC_PLLSAI1CFG_PLLN(12)
|
|
#define STM32L4_PLLSAI1CFG_PLLP 0
|
|
#undef STM32L4_PLLSAI1CFG_PLLP_ENABLED
|
|
#define STM32L4_PLLSAI1CFG_PLLQ RCC_PLLSAI1CFG_PLLQ_4
|
|
#define STM32L4_PLLSAI1CFG_PLLQ_ENABLED
|
|
#define STM32L4_PLLSAI1CFG_PLLR 0
|
|
#undef STM32L4_PLLSAI1CFG_PLLR_ENABLED
|
|
|
|
/* 'SAIPLL2' is not used in this application */
|
|
|
|
#define STM32L4_PLLSAI2CFG_PLLN RCC_PLLSAI2CFG_PLLN(8)
|
|
#define STM32L4_PLLSAI2CFG_PLLP 0
|
|
#undef STM32L4_PLLSAI2CFG_PLLP_ENABLED
|
|
#define STM32L4_PLLSAI2CFG_PLLR 0
|
|
#undef STM32L4_PLLSAI2CFG_PLLR_ENABLED
|
|
|
|
/* Enable CLK48; get it from PLLSAI1 */
|
|
|
|
#if defined(CONFIG_STM32L4_OTGFS) || defined(STM32L4_SDMMC) || defined(CONFIG_STM32L4_RNG)
|
|
# define STM32L4_USE_CLK48 1
|
|
# define STM32L4_CLK48_SEL RCC_CCIPR_CLK48SEL_PLLSAI1
|
|
# define STM32L4_HSI48_SYNCSRC SYNCSRC_NONE
|
|
#endif
|
|
|
|
/* Enable LSE (for the RTC) */
|
|
|
|
#define STM32L4_USE_LSE 1
|
|
|
|
/* HSI16 used as I2C clock */
|
|
|
|
#define STM32L4_I2C_USE_HSI16 1
|
|
|
|
/* Configure the HCLK divisor (for the AHB bus, core, memory, and DMA */
|
|
|
|
#define STM32L4_RCC_CFGR_HPRE RCC_CFGR_HPRE_SYSCLK /* HCLK = SYSCLK / 1 */
|
|
#define STM32L4_HCLK_FREQUENCY STM32L4_SYSCLK_FREQUENCY
|
|
|
|
/* Configure the APB1 prescaler */
|
|
|
|
#define STM32L4_RCC_CFGR_PPRE1 RCC_CFGR_PPRE1_HCLK /* PCLK1 = HCLK / 1 */
|
|
#define STM32L4_PCLK1_FREQUENCY (STM32L4_HCLK_FREQUENCY / 1)
|
|
|
|
#define STM32L4_APB1_TIM2_CLKIN (STM32L4_PCLK1_FREQUENCY)
|
|
#define STM32L4_APB1_TIM3_CLKIN (STM32L4_PCLK1_FREQUENCY)
|
|
#define STM32L4_APB1_TIM4_CLKIN (STM32L4_PCLK1_FREQUENCY)
|
|
#define STM32L4_APB1_TIM5_CLKIN (STM32L4_PCLK1_FREQUENCY)
|
|
#define STM32L4_APB1_TIM6_CLKIN (STM32L4_PCLK1_FREQUENCY)
|
|
#define STM32L4_APB1_TIM7_CLKIN (STM32L4_PCLK1_FREQUENCY)
|
|
|
|
/* Configure the APB2 prescaler */
|
|
|
|
#define STM32L4_RCC_CFGR_PPRE2 RCC_CFGR_PPRE2_HCLK /* PCLK2 = HCLK / 1 */
|
|
#define STM32L4_PCLK2_FREQUENCY (STM32L4_HCLK_FREQUENCY / 1)
|
|
|
|
#define STM32L4_APB2_TIM1_CLKIN (STM32L4_PCLK2_FREQUENCY)
|
|
#define STM32L4_APB2_TIM8_CLKIN (STM32L4_PCLK2_FREQUENCY)
|
|
|
|
#elif defined(MSI_CLOCK_CONFIG)
|
|
|
|
/* Use the MSI; frequ = 4 MHz; autotrim from LSE */
|
|
|
|
#define STM32L4_BOARD_USEMSI 1
|
|
#define STM32L4_BOARD_MSIRANGE RCC_CR_MSIRANGE_4M
|
|
|
|
/* Prescaler common to all PLL inputs */
|
|
|
|
#define STM32L4_PLLCFG_PLLM RCC_PLLCFG_PLLM(1)
|
|
|
|
/* 'main' PLL config; we use this to generate our system clock via the R
|
|
* output. We set it up as 4 MHz / 1 * 60 / 2 = 120 MHz
|
|
*
|
|
* XXX NOTE:
|
|
* currently the main PLL is implicitly turned on and is implicitly
|
|
* the system clock; this should be configurable since not all
|
|
* applications may want things done this way.
|
|
*/
|
|
|
|
#define STM32L4_PLLCFG_PLLN RCC_PLLCFG_PLLN(60)
|
|
#define STM32L4_PLLCFG_PLLP 0
|
|
#undef STM32L4_PLLCFG_PLLP_ENABLED
|
|
#define STM32L4_PLLCFG_PLLQ RCC_PLLCFG_PLLQ_2
|
|
#define STM32L4_PLLCFG_PLLQ_ENABLED
|
|
#define STM32L4_PLLCFG_PLLR RCC_PLLCFG_PLLR_2
|
|
#define STM32L4_PLLCFG_PLLR_ENABLED
|
|
|
|
/* 'SAIPLL1' is used to generate the 48 MHz clock, since we can't
|
|
* do that with the main PLL's N value. We set N = 12, and enable
|
|
* the Q output (ultimately for CLK48) with /4. So,
|
|
* 4 MHz / 1 * 24 / 2 = 48 MHz
|
|
*
|
|
* XXX NOTE: currently the SAIPLL /must/ be explicitly selected in the
|
|
* menuconfig, or else all this is a moot point, and the various 48 MHz
|
|
* peripherals will not work (RNG at present). I would suggest removing
|
|
* that option from Kconfig altogether, and simply making it an option
|
|
* that is selected via a #define here, like all these other params.
|
|
*/
|
|
|
|
#define STM32L4_PLLSAI1CFG_PLLN RCC_PLLSAI1CFG_PLLN(24)
|
|
#define STM32L4_PLLSAI1CFG_PLLP 0
|
|
#undef STM32L4_PLLSAI1CFG_PLLP_ENABLED
|
|
#define STM32L4_PLLSAI1CFG_PLLQ RCC_PLLSAI1CFG_PLLQ_2
|
|
#define STM32L4_PLLSAI1CFG_PLLQ_ENABLED
|
|
#define STM32L4_PLLSAI1CFG_PLLR 0
|
|
#undef STM32L4_PLLSAI1CFG_PLLR_ENABLED
|
|
|
|
/* 'SAIPLL2' is not used in this application */
|
|
|
|
#define STM32L4_PLLSAI2CFG_PLLN RCC_PLLSAI2CFG_PLLN(8)
|
|
#define STM32L4_PLLSAI2CFG_PLLP 0
|
|
#undef STM32L4_PLLSAI2CFG_PLLP_ENABLED
|
|
#define STM32L4_PLLSAI2CFG_PLLR 0
|
|
#undef STM32L4_PLLSAI2CFG_PLLR_ENABLED
|
|
|
|
/* Enable CLK48; get it from PLLSAI1 */
|
|
|
|
#if defined(CONFIG_STM32L4_OTGFS) || defined(STM32L4_SDMMC) || defined(CONFIG_STM32L4_RNG)
|
|
# define STM32L4_USE_CLK48 1
|
|
# define STM32L4_CLK48_SEL RCC_CCIPR_CLK48SEL_PLLSAI1
|
|
# define STM32L4_HSI48_SYNCSRC SYNCSRC_NONE
|
|
#endif
|
|
|
|
/* Enable LSE (for the RTC) */
|
|
|
|
#define STM32L4_USE_LSE 1
|
|
|
|
/* HSI16 used as I2C clock */
|
|
|
|
#define STM32L4_I2C_USE_HSI16 1
|
|
|
|
/* Configure the HCLK divisor (for the AHB bus, core, memory, and DMA */
|
|
|
|
#define STM32L4_RCC_CFGR_HPRE RCC_CFGR_HPRE_SYSCLK /* HCLK = SYSCLK / 1 */
|
|
#define STM32L4_HCLK_FREQUENCY STM32L4_SYSCLK_FREQUENCY
|
|
|
|
/* Configure the APB1 prescaler */
|
|
|
|
#define STM32L4_RCC_CFGR_PPRE1 RCC_CFGR_PPRE1_HCLK /* PCLK1 = HCLK / 1 */
|
|
#define STM32L4_PCLK1_FREQUENCY (STM32L4_HCLK_FREQUENCY / 1)
|
|
|
|
#define STM32L4_APB1_TIM2_CLKIN (STM32L4_PCLK1_FREQUENCY)
|
|
#define STM32L4_APB1_TIM3_CLKIN (STM32L4_PCLK1_FREQUENCY)
|
|
#define STM32L4_APB1_TIM4_CLKIN (STM32L4_PCLK1_FREQUENCY)
|
|
#define STM32L4_APB1_TIM5_CLKIN (STM32L4_PCLK1_FREQUENCY)
|
|
#define STM32L4_APB1_TIM6_CLKIN (STM32L4_PCLK1_FREQUENCY)
|
|
#define STM32L4_APB1_TIM7_CLKIN (STM32L4_PCLK1_FREQUENCY)
|
|
|
|
/* Configure the APB2 prescaler */
|
|
|
|
#define STM32L4_RCC_CFGR_PPRE2 RCC_CFGR_PPRE2_HCLK /* PCLK2 = HCLK / 1 */
|
|
#define STM32L4_PCLK2_FREQUENCY (STM32L4_HCLK_FREQUENCY / 1)
|
|
|
|
#define STM32L4_APB2_TIM1_CLKIN (STM32L4_PCLK2_FREQUENCY)
|
|
#define STM32L4_APB2_TIM8_CLKIN (STM32L4_PCLK2_FREQUENCY)
|
|
|
|
#endif /* clock selection */
|
|
|
|
/* The timer clock frequencies are automatically defined by hardware.
|
|
* If the APB prescaler equals 1, the timer clock frequencies are set to the
|
|
* same frequency as that of the APB domain. Otherwise they are set to twice.
|
|
* Note: TIM1,8,15,16,17 are on APB2, others on APB1
|
|
*/
|
|
|
|
#define BOARD_TIM1_FREQUENCY STM32L4_HCLK_FREQUENCY
|
|
#define BOARD_TIM2_FREQUENCY STM32L4_HCLK_FREQUENCY
|
|
#define BOARD_TIM3_FREQUENCY STM32L4_HCLK_FREQUENCY
|
|
#define BOARD_TIM4_FREQUENCY STM32L4_HCLK_FREQUENCY
|
|
#define BOARD_TIM5_FREQUENCY STM32L4_HCLK_FREQUENCY
|
|
#define BOARD_TIM6_FREQUENCY STM32L4_HCLK_FREQUENCY
|
|
#define BOARD_TIM7_FREQUENCY STM32L4_HCLK_FREQUENCY
|
|
#define BOARD_TIM8_FREQUENCY STM32L4_HCLK_FREQUENCY
|
|
#define BOARD_TIM15_FREQUENCY STM32L4_HCLK_FREQUENCY
|
|
#define BOARD_TIM16_FREQUENCY STM32L4_HCLK_FREQUENCY
|
|
#define BOARD_TIM17_FREQUENCY STM32L4_HCLK_FREQUENCY
|
|
#define BOARD_LPTIM1_FREQUENCY STM32L4_HCLK_FREQUENCY
|
|
#define BOARD_LPTIM2_FREQUENCY STM32L4_HCLK_FREQUENCY
|
|
|
|
/****************************************************************************
|
|
* Public Data
|
|
****************************************************************************/
|
|
|
|
#ifndef __ASSEMBLY__
|
|
|
|
#undef EXTERN
|
|
#if defined(__cplusplus)
|
|
#define EXTERN extern "C"
|
|
extern "C"
|
|
{
|
|
#else
|
|
#define EXTERN extern
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Public Function Prototypes
|
|
****************************************************************************/
|
|
|
|
#undef EXTERN
|
|
#if defined(__cplusplus)
|
|
}
|
|
#endif
|
|
|
|
#endif /* __ASSEMBLY__ */
|
|
#endif /* __BOARDS_ARM_STM32L4_STM32L4R9AI_DISCO_INCLUDE_STM32L4R9AI_DISCO_CLOCKING_H */
|