471 lines
15 KiB
Plaintext
471 lines
15 KiB
Plaintext
README
|
||
======
|
||
|
||
This README discusses issues unique to NuttX configurations for the ST
|
||
Nucleo-l432kc board from ST Micro. See
|
||
|
||
http://www.st.com/nucleo-l432kc
|
||
|
||
NucleoL432KC:
|
||
|
||
Microprocessor: 32-bit ARM Cortex M4 at 80MHz STM32L432KCU6
|
||
Memory: 256 KB Flash and 64 KB SRAM
|
||
ADC: 1×12-bit, 5 MSPS A/D converter: up to 10 channels
|
||
DMA: 16-stream DMA controllers with FIFOs and burst support
|
||
Timers: Up to 11 timers: up to five 16-bit, one 32-bit, two low-power
|
||
16 bit timers, two watchdog timers, and a SysTick timer
|
||
GPIO: Up to 26 I/O ports with interrupt capability, most 5v tolerant
|
||
I2C: Up to 2 × I2C interfaces
|
||
USARTs: Up to 3 USARTs, 2 UARTs, 1 LPUART
|
||
SPIs: Up to 2 SPIs
|
||
SAIs: 1 dual-channel audio interface
|
||
CAN interface
|
||
QSPI interface
|
||
USB: USB 2.0 full-speed device/host/OTG controller with on-chip PHY
|
||
CRC calculation unit
|
||
RTC
|
||
|
||
Board features:
|
||
|
||
Peripherals: 1 led
|
||
Debug: Serial wire debug and JTAG interfaces via on-board micro-usb stlink v2.1
|
||
Expansion I/F Arduino Nano Headers
|
||
|
||
Uses a STM32F103 to provide a ST-Link for programming, debug similar to the
|
||
OpenOcd FTDI function - USB to JTAG front-end.
|
||
|
||
See http://mbed.org/platforms/ST-Nucleo-L432KC for more
|
||
information about these boards.
|
||
|
||
Contents
|
||
========
|
||
|
||
- Nucleo-32 Boards
|
||
- Development Environment
|
||
- GNU Toolchain Options
|
||
- IDEs
|
||
- NuttX EABI "buildroot" Toolchain
|
||
- NXFLAT Toolchain
|
||
- Hardware
|
||
- Button
|
||
- LED
|
||
- USARTs and Serial Consoles
|
||
- QFN32
|
||
- mbed
|
||
- SPI Flash support
|
||
- Configurations
|
||
|
||
Nucleo-32 Boards
|
||
================
|
||
|
||
The Nucleo-L432KC is a member of the Nucleo-64 board family. The Nucleo-64
|
||
is a standard board for use with several STM32 parts in the LQFP64 package.
|
||
Variants include
|
||
|
||
Order code Targeted STM32
|
||
------------- --------------
|
||
NUCLEO-F031K6 STM32F031K6T6
|
||
NUCLEO-F042K6 STM32F042K6T6
|
||
NUCLEO-F303K8 STM32F303K8T6
|
||
NUCLEO-L011K4 STM32L011K4T6
|
||
NUCLEO-L031K6 STM32L031K6T6
|
||
NUCLEO-L432KC STM32L432KCU6
|
||
|
||
Development Environment
|
||
=======================
|
||
|
||
Either Linux or Cygwin on Windows can be used for the development environment.
|
||
The source has been built only using the GNU toolchain (see below). Other
|
||
toolchains will likely cause problems.
|
||
|
||
GNU Toolchain Options
|
||
=====================
|
||
|
||
Toolchain Configurations
|
||
------------------------
|
||
The NuttX make system has been modified to support the following different
|
||
toolchain options.
|
||
|
||
1. The NuttX buildroot Toolchain (see below), or
|
||
2. Any generic arm-none-eabi GNU toolchain.
|
||
|
||
All testing has been conducted using the NuttX CodeSourcery toolchain. To use
|
||
a different toolchain, you simply need to modify the configuration. As an
|
||
example:
|
||
|
||
CONFIG_ARM_TOOLCHAIN_GNU_EABIL : Generic arm-none-eabi toolchain
|
||
|
||
IDEs
|
||
====
|
||
|
||
NuttX is built using command-line make. It can be used with an IDE, but some
|
||
effort will be required to create the project.
|
||
|
||
Makefile Build
|
||
--------------
|
||
Under Eclipse, it is pretty easy to set up an "empty makefile project" and
|
||
simply use the NuttX makefile to build the system. That is almost for free
|
||
under Linux. Under Windows, you will need to set up the "Cygwin GCC" empty
|
||
makefile project in order to work with Windows (Google for "Eclipse Cygwin" -
|
||
there is a lot of help on the internet).
|
||
|
||
Using Sourcery CodeBench from http://www.mentor.com/embedded-software/sourcery-tools/sourcery-codebench/overview
|
||
Download and install the latest version (as of this writing it was
|
||
sourceryg++-2013.05-64-arm-none-eabi)
|
||
|
||
Import the project from git.
|
||
File->import->Git-URI, then import a Exiting code as a Makefile progject
|
||
from the working directory the git clone was done to.
|
||
|
||
Select the Sourcery CodeBench for ARM EABI. N.B. You must do one command line
|
||
build, before the make will work in CodeBench.
|
||
|
||
Native Build
|
||
------------
|
||
Here are a few tips before you start that effort:
|
||
|
||
1) Select the toolchain that you will be using in your .config file
|
||
2) Start the NuttX build at least one time from the Cygwin command line
|
||
before trying to create your project. This is necessary to create
|
||
certain auto-generated files and directories that will be needed.
|
||
3) Set up include paths: You will need include/, arch/arm/src/stm32,
|
||
arch/arm/src/common, arch/arm/src/armv7-m, and sched/.
|
||
4) All assembly files need to have the definition option -D __ASSEMBLY__
|
||
on the command line.
|
||
|
||
Startup files will probably cause you some headaches. The NuttX startup file
|
||
is arch/arm/src/stm32/stm32_vectors.S. With RIDE, I have to build NuttX
|
||
one time from the Cygwin command line in order to obtain the pre-built
|
||
startup object needed by RIDE.
|
||
|
||
NuttX EABI "buildroot" Toolchain
|
||
================================
|
||
|
||
A GNU GCC-based toolchain is assumed. The PATH environment variable should
|
||
be modified to point to the correct path to the Cortex-M3 GCC toolchain (if
|
||
different from the default in your PATH variable).
|
||
|
||
If you have no Cortex-M3 toolchain, one can be downloaded from the NuttX
|
||
Bitbucket download site (https://bitbucket.org/nuttx/buildroot/downloads/).
|
||
This GNU toolchain builds and executes in the Linux or Cygwin environment.
|
||
|
||
1. You must have already configured NuttX in <some-dir>/nuttx.
|
||
|
||
$ tools/configure.sh nucleo-l432kc:nsh
|
||
$ make qconfig
|
||
$ V=1 make context all 2>&1 | tee mout
|
||
|
||
2. Download the latest buildroot package into <some-dir>
|
||
|
||
3. unpack the buildroot tarball. The resulting directory may
|
||
have versioning information on it like buildroot-x.y.z. If so,
|
||
rename <some-dir>/buildroot-x.y.z to <some-dir>/buildroot.
|
||
|
||
4. cd <some-dir>/buildroot
|
||
|
||
5. cp boards/cortexm3-eabi-defconfig-4.6.3 .config
|
||
|
||
6. make oldconfig
|
||
|
||
7. make
|
||
|
||
8. Make sure that the PATH variable includes the path to the newly built
|
||
binaries.
|
||
|
||
See the file boards/README.txt in the buildroot source tree. That has more
|
||
details PLUS some special instructions that you will need to follow if you are
|
||
building a Cortex-M3 toolchain for Cygwin under Windows.
|
||
|
||
NOTE: Unfortunately, the 4.6.3 EABI toolchain is not compatible with the
|
||
the NXFLAT tools. See the top-level TODO file (under "Binary loaders") for
|
||
more information about this problem. If you plan to use NXFLAT, please do not
|
||
use the GCC 4.6.3 EABI toolchain; instead use the GCC 4.3.3 EABI toolchain.
|
||
|
||
NXFLAT Toolchain
|
||
================
|
||
|
||
If you are *not* using the NuttX buildroot toolchain and you want to use
|
||
the NXFLAT tools, then you will still have to build a portion of the buildroot
|
||
tools -- just the NXFLAT tools. The buildroot with the NXFLAT tools can
|
||
be downloaded from the NuttX Bitbucket download site
|
||
(https://bitbucket.org/nuttx/nuttx/downloads/).
|
||
|
||
This GNU toolchain builds and executes in the Linux or Cygwin environment.
|
||
|
||
1. You must have already configured NuttX in <some-dir>/nuttx.
|
||
|
||
tools/configure.sh lpcxpresso-lpc1768:<sub-dir>
|
||
|
||
2. Download the latest buildroot package into <some-dir>
|
||
|
||
3. unpack the buildroot tarball. The resulting directory may
|
||
have versioning information on it like buildroot-x.y.z. If so,
|
||
rename <some-dir>/buildroot-x.y.z to <some-dir>/buildroot.
|
||
|
||
4. cd <some-dir>/buildroot
|
||
|
||
5. cp boards/cortexm3-defconfig-nxflat .config
|
||
|
||
6. make oldconfig
|
||
|
||
7. make
|
||
|
||
8. Make sure that the PATH variable includes the path to the newly built
|
||
NXFLAT binaries.
|
||
|
||
mbed
|
||
====
|
||
|
||
The Nucleo-L432KC includes boot loader from mbed:
|
||
|
||
https://mbed.org/handbook/Homepage
|
||
|
||
Using the mbed loader:
|
||
|
||
1. Connect the Nucleo-L432kc to the host PC using the USB connector.
|
||
2. A new file system will appear called NUCLEO; open it with Windows
|
||
Explorer (assuming that you are using Windows).
|
||
3. Drag and drop nuttx.bin into the MBED window. This will load the
|
||
nuttx.bin binary into the Nucleo-L432kc. The NUCLEO window will
|
||
close then re-open and the Nucleo-L432KC will be running the new code.
|
||
|
||
Hardware
|
||
========
|
||
|
||
LEDs
|
||
----
|
||
The Nucleo L432KC provides a single user LED, LD3. LD3
|
||
is the green LED connected to Arduino signal D13 corresponding to MCU I/O
|
||
PB3 (pin 26).
|
||
|
||
- When the I/O is HIGH value, the LED is on.
|
||
- When the I/O is LOW, the LED is off.
|
||
|
||
These LEDs are not used by the board port unless CONFIG_ARCH_LEDS is
|
||
defined. In that case, the usage by the board port is defined in
|
||
include/board.h and src/sam_leds.c. The LEDs are used to encode OS-related
|
||
events as follows when the LED is available:
|
||
|
||
SYMBOL Meaning LD3
|
||
------------------- ----------------------- -----------
|
||
LED_STARTED NuttX has been started OFF
|
||
LED_HEAPALLOCATE Heap has been allocated OFF
|
||
LED_IRQSENABLED Interrupts enabled OFF
|
||
LED_STACKCREATED Idle stack created ON
|
||
LED_INIRQ In an interrupt No change
|
||
LED_SIGNAL In a signal handler No change
|
||
LED_ASSERTION An assertion failed No change
|
||
LED_PANIC The system has crashed Blinking
|
||
LED_IDLE MCU is is sleep mode Not used
|
||
|
||
Thus if LD3, NuttX has successfully booted and is, apparently, running
|
||
normally. If LD3 is flashing at approximately 2Hz, then a fatal error
|
||
has been detected and the system has halted.
|
||
|
||
Serial Consoles
|
||
===============
|
||
|
||
USART1
|
||
------
|
||
Pins and Connectors:
|
||
|
||
RXD: PA11 CN10 pin 14
|
||
PB7 CN7 pin 21
|
||
TXD: PA10 CN9 pin 3, CN10 pin 33
|
||
PB6 CN5 pin 3, CN10 pin 17
|
||
|
||
NOTE: You may need to edit the include/board.h to select different USART1
|
||
pin selections.
|
||
|
||
TTL to RS-232 converter connection:
|
||
|
||
Nucleo CN10 STM32L432KC
|
||
----------- ------------
|
||
Pin 21 PA9 USART1_RX *Warning you make need to reverse RX/TX on
|
||
Pin 33 PA10 USART1_TX some RS-232 converters
|
||
Pin 20 GND
|
||
Pin 8 U5V
|
||
|
||
To configure USART1 as the console:
|
||
|
||
CONFIG_STM32_USART1=y
|
||
CONFIG_USART1_SERIALDRIVER=y
|
||
CONFIG_USART1_SERIAL_CONSOLE=y
|
||
CONFIG_USART1_RXBUFSIZE=256
|
||
CONFIG_USART1_TXBUFSIZE=256
|
||
CONFIG_USART1_BAUD=115200
|
||
CONFIG_USART1_BITS=8
|
||
CONFIG_USART1_PARITY=0
|
||
CONFIG_USART1_2STOP=0
|
||
|
||
USART2
|
||
-----
|
||
Pins and Connectors:
|
||
|
||
RXD: PA3 CN9 pin 1 (See SB13, 14, 62, 63). CN10 pin 37
|
||
PD6
|
||
TXD: PA2 CN9 pin 2(See SB13, 14, 62, 63). CN10 pin 35
|
||
PD5
|
||
|
||
UART2 is the default in all of these configurations.
|
||
|
||
TTL to RS-232 converter connection:
|
||
|
||
Nucleo CN9 STM32L432KC
|
||
----------- ------------
|
||
Pin 1 PA3 USART2_RX *Warning you make need to reverse RX/TX on
|
||
Pin 2 PA2 USART2_TX some RS-232 converters
|
||
|
||
Solder Bridges. This configuration requires:
|
||
|
||
- SB62 and SB63 Closed: PA2 and PA3 on STM32 MCU are connected to D1 and D0
|
||
(pin 7 and pin 8) on Arduino connector CN9 and ST Morpho connector CN10
|
||
as USART signals. Thus SB13 and SB14 should be OFF.
|
||
|
||
- SB13 and SB14 Open: PA2 and PA3 on STM32F103C8T6 (ST-LINK MCU) are
|
||
disconnected to PA3 and PA2 on STM32 MCU.
|
||
|
||
To configure USART2 as the console:
|
||
|
||
CONFIG_STM32_USART2=y
|
||
CONFIG_USART2_SERIALDRIVER=y
|
||
CONFIG_USART2_SERIAL_CONSOLE=y
|
||
CONFIG_USART2_RXBUFSIZE=256
|
||
CONFIG_USART2_TXBUFSIZE=256
|
||
CONFIG_USART2_BAUD=115200
|
||
CONFIG_USART2_BITS=8
|
||
CONFIG_USART2_PARITY=0
|
||
CONFIG_USART2_2STOP=0
|
||
|
||
Virtual COM Port
|
||
----------------
|
||
Yet another option is to use UART2 and the USB virtual COM port. This
|
||
option may be more convenient for long term development, but is painful
|
||
to use during board bring-up.
|
||
|
||
Solder Bridges. This configuration requires:
|
||
|
||
- SB62 and SB63 Open: PA2 and PA3 on STM32 MCU are disconnected to D1
|
||
and D0 (pin 7 and pin 8) on Arduino connector CN9 and ST Morpho
|
||
connector CN10.
|
||
|
||
- SB13 and SB14 Closed: PA2 and PA3 on STM32F103C8T6 (ST-LINK MCU) are
|
||
connected to PA3 and PA2 on STM32 MCU to have USART communication
|
||
between them. Thus SB61, SB62 and SB63 should be OFF.
|
||
|
||
Configuring USART2 is the same as given above.
|
||
|
||
Question: What BAUD should be configure to interface with the Virtual
|
||
COM port? 115200 8N1?
|
||
|
||
Default
|
||
-------
|
||
As shipped, SB62 and SB63 are open and SB13 and SB14 closed, so the
|
||
virtual COM port is enabled.
|
||
|
||
SPI Flash support:
|
||
=====================
|
||
|
||
We can use an external SPI Serial Flash with nucleo-l432kc board. In this
|
||
case we tested with AT45DB081D (8Mbit = 1MiB).
|
||
|
||
You can connect the AT45DB081D memory in the nucleo-l432kc board this way:
|
||
|
||
--------------------------------
|
||
| Memory nucleo-l432kc |
|
||
|------------------------------|
|
||
| SI ---> D11 (PB5) |
|
||
| SCK ---> D13 (PB3) |
|
||
| /RESET ---> 3V3 |
|
||
| /CS ---> D10 (PA11) |
|
||
| /WP ---> 3V3 |
|
||
| VCC ---> 3V3 |
|
||
| GND ---> GND |
|
||
| SO ---> D12 (PB4) |
|
||
--------------------------------
|
||
|
||
You can start with default "nucleo-l432kc/nsh" configuration option and
|
||
enable/disable these options using "make menuconfig" :
|
||
|
||
System Type --->
|
||
STM32L4 Peripheral Support --->
|
||
[*] SPI1
|
||
|
||
Device Drivers --->
|
||
-*- Memory Technology Device (MTD) Support --->
|
||
-*- SPI-based AT45DB flash
|
||
(1000000) AT45DB Frequency
|
||
|
||
File Systems --->
|
||
[*] NXFFS file system
|
||
|
||
|
||
Then after compiling and flashing the file nuttx.bin you can test the flash
|
||
this way:
|
||
|
||
nsh> ls /mnt
|
||
/mnt:
|
||
at45db/
|
||
|
||
nsh> echo "Testing" > /mnt/at45db/file.txt
|
||
|
||
nsh> ls /mnt/at45db
|
||
/mnt/at45db:
|
||
file.txt
|
||
|
||
nsh> cat /mnt/at45db/file.txt
|
||
Testing
|
||
|
||
nsh>
|
||
|
||
Configurations
|
||
==============
|
||
|
||
nsh:
|
||
---------
|
||
Configures the NuttShell (nsh) located at apps/examples/nsh for the
|
||
Nucleo-L432KC board. The Configuration enables the serial interfaces
|
||
on UART2. Support for builtin applications is enabled, but in the base
|
||
configuration no builtin applications are selected (see NOTES below).
|
||
|
||
NOTES:
|
||
|
||
1. This configuration uses the mconf-based configuration tool. To
|
||
change this configuration using that tool, you should:
|
||
|
||
a. Build and install the kconfig-mconf tool. See nuttx/README.txt
|
||
see additional README.txt files in the NuttX tools repository.
|
||
|
||
b. Execute 'make menuconfig' in nuttx/ in order to start the
|
||
reconfiguration process.
|
||
|
||
2. By default, this configuration uses the ARM EABI toolchain
|
||
for Linux. That can easily be reconfigured, of course.
|
||
|
||
CONFIG_HOST_LINUX=y : Builds under Linux
|
||
CONFIG_ARMV7M_TOOLCHAIN_GNU_EABIL=y : GNU EABI toolchain for Linux
|
||
|
||
3. Although the default console is USART2 (which would correspond to
|
||
the Virtual COM port) I have done all testing with the console
|
||
device configured for USART1 (see instruction above under "Serial
|
||
Consoles). I have been using a TTL-to-RS-232 converter connected
|
||
as shown below:
|
||
|
||
Nucleo CN10 STM32L432KC
|
||
----------- ------------
|
||
Pin 21 PA9 USART1_RX *Warning you make need to reverse RX/TX on
|
||
Pin 33 PA10 USART1_TX some RS-232 converters
|
||
Pin 20 GND
|
||
Pin 8 U5V
|
||
|
||
spwm
|
||
----
|
||
|
||
Configures the sinusoidal PWM (SPWM) example which presents a simple use case
|
||
of the STM32L4 PWM lower-half driver without generic upper-half PWM logic.
|
||
|
||
It uses TIM1 to generate PWM and TIM6 to change waveform samples
|
||
|
||
At the moment, the waveform parameters are hardcoded, but it should be easy to
|
||
modify this example and make it more functional.
|