nuttx/arch/README.txt
patacongo faa9c3927d Documentatin update
git-svn-id: svn://svn.code.sf.net/p/nuttx/code/trunk@3686 42af7a65-404d-4744-a932-0658087f49c3
2011-06-09 00:02:24 +00:00

333 lines
14 KiB
Plaintext

Architecture-Specific Code
^^^^^^^^^^^^^^^^^^^^^^^^^^
Table of Contents
^^^^^^^^^^^^^^^^^
o Architecture-Specific Code
o Summary of Files
o Supported Architectures
o Configuring NuttX
Architecture-Specific Code
^^^^^^^^^^^^^^^^^^^^^^^^^^
The NuttX configuration consists of:
o Processor architecture specific files. These are the files contained
in the arch/<arch-name>/ directory discussed in this README.
o Chip/SoC specific files. Each processor processor architecture
is embedded in chip or System-on-a-Chip (SoC) architecture. The
full chip architecture includes the processor architecture plus
chip-specific interrupt logic, general purpose I/O (GIO) logic, and
specialized, internal peripherals (such as UARTs, USB, etc.).
These chip-specific files are contained within chip-specific
sub-directories in the arch/<arch-name>/ directory and are selected
via the CONFIG_ARCH_name selection
o Board specific files. In order to be usable, the chip must be
contained in a board environment. The board configuration defines
additional properties of the board including such things as
peripheral LEDs, external peripherals (such as network, USB, etc.).
These board-specific configuration files can be found in the
configs/<board-name>/ sub-directories.
This README will address the processor architecture specific files
that are contained in the arch/<arch-name>/ directory. The file
include/nuttx/arch.h identifies all of the APIs that must
be provided by this architecture specific logic. (It also includes
arch/<arch-name>/arch.h as described below).
Directory Structure
^^^^^^^^^^^^^^^^^^^
The arch directory contains architecture specific logic. The complete
board port in is defined by the architecture-specific code in this
directory (plus the board-specific configurations in the config/
subdirectory). Each architecture must provide a subdirectory <arch-name>
under arch/ with the following characteristics:
<arch-name>/
|-- include/
| |--<chip-name>/
| | `-- (chip-specific header files)
| |--<other-chips>/
| |-- arch.h
| |-- irq.h
| `-- types.h
`-- src/
|--<chip-name>/
| `-- (chip-specific source files)
|--<other-chips>/
|-- Makefile
`-- (architecture-specific source files)
Summary of Files
^^^^^^^^^^^^^^^^
include/<chip-name>/
This sub-directory contains chip-specific header files.
include/arch.h
This is a hook for any architecture specific definitions that may
be needed by the system. It is included by include/nuttx/arch.h
include/types.h
This provides architecture/toolchain-specific definitions for
standard types. This file should typedef:
_int8_t, _uint8_t, _int16_t, _uint16_t, _int32_t, _uint32_t
and if the architecture supports 64-bit integers.
_int24_t, _uint24_t, int64_t, uint64_t
NOTE that these type names have a leading underscore character. This
file will be included(indirectly) by include/stdint.h and typedef'ed to
the final name without the underscore character. This roundabout way of
doings things allows the stdint.h to be removed from the include/
directory in the event that the user prefers to use the definitions
provided by their toolchain header files
irqstate_t
Must be defined to the be the size required to hold the interrupt
enable/disable state.
This file will be included by include/sys/types.h and be made
available to all files.
include/irq.h
This file needs to define some architecture specific functions (usually
inline if the compiler supports inlining) and structure. These include:
- struct xcptcontext. This structures represents the saved context
of a thread.
- irqstate_t irqsave(void) -- Used to disable all interrupts.
- void irqrestore(irqstate_t flags) -- Used to restore interrupt
enables to the same state as before irqsave was called.
This file must also define NR_IRQS, the total number of IRQs supported
by the board.
src/<chip-name>/
This sub-directory contains chip-specific source files.
src/Makefile
This makefile will be executed to build the targets src/libup.a and
src/up_head.o. The up_head.o file holds the entry point into the system
(power-on reset entry point, for example). It will be used in
the final link with libup.a and other system archives to generate the
final executable.
Supported Architectures
^^^^^^^^^^^^^^^^^^^^^^^
arch/sim - Linux/Cygwin simulation
A user-mode port of NuttX to the x86 Linux platform is available.
The purpose of this port is primarily to support OS feature development.
This port does not support interrupts or a real timer (and hence no
round robin scheduler) Otherwise, it is complete.
arch/arm - ARM-based micro-controllers
This directory holds common ARM architectures. At present, this includes
the following subdirectories:
arch/arm/include and arch/arm/src/common
Common ARM/Cortex-M3 logic.
arch/arm/src/arm and arch/arm/include/arm
Common ARM-specific logic
arch/arm/src/cortexm3 and arch/arm/include/cortexm3
Common Cortex-M3 logic
arch/arm/include/c5471 and arch/arm/src/c5471
TI TMS320C5471 (also called TMS320DM180 or just C5471).
NuttX operates on the ARM7 of this dual core processor. This port
complete, verified, and included in the NuttX release 0.1.1.
arch/arm/include/dm320 and arch/arm/src/dm320
TI TMS320DM320 (also called just DM320).
NuttX operates on the ARM9EJS of this dual core processor. This port
complete, verified, and included in the NuttX release 0.2.1.
arch/arm/include/imx and arch/arm/src/imx
Freescale MC9328MX1 or i.MX1. This port uses the Freescale MX1ADS
development board with a GNU arm-elf toolchain* under either Linux or Cygwin.
STATUS: This port has stalled because of development tool issues. Coding
is complete on the basic port (timer, serial console, SPI).
arch/arm/include/lm3s and arch/arm/src/lm3s
These directories contain support for the Luminary LMS family, particularly
for the LM3S6918. The initial, release of this port was included in NuttX version
0.4.6. The current port includes timer, serial console, Ethernet, SSI, and microSD
support. There are working configurations the NuttX OS test, to run the NuttShell
(NSH), the NuttX networking test, and the uIP web server.
arch/arm/include/lpc214x and arch/arm/src/lpc214x
These directories provide support for NXP LPC214x family of
ARM7TDMI processors. This port boots and passes the OS test (examples/ostest).
The port is complete and verifed. As of NuttX 0.3.17, the port includes:
timer interrupts, serial console, USB driver, and SPI-based MMC/SD card
support. A verifed NuttShell (NSH) configuration is also available.
arch/arm/include/lpc2378 and arch/arm/src/lpc2378.
NXP LPC2378. Support is provided for the NXP LPC2378 MCU. This port was
contributed by Rommel Marcelo is was first released in NuttX-5.3.
STATUS: This port boots and passes the OS test (examples/ostest) and
includes a working implementation of the NuttShell (NSH). The port is
complete and verified. As of NuttX 5.3, the port includes only basic
timer interrupts and serial console support.
arch/arm/include/lpc313x and arch/arm/src/lpc313x
These directories provide support for NXP LPC313x family of
ARM926EJ-S processors. The port for the NXP LPC3131 was first
released in NuttX-5.1 (but was not functional until NuttX-5.2).
STATUS: The basic EA3131 port is complete and verified in NuttX-5.2
This basic port includes basic boot-up, serial console, and timer
interrupts. This port was extended in NuttX 5.3 with a USB high
speed driver contributed by David Hewson. This port has been
verified using the NuttX OS test, USB serial and mass storage tests
and includes a working implementation of the NuttShell ((NSH)).
arch/arm/include/sam3u and arch/arm/src/sam3u
Atmel AT91SAM3U. This port is for Atmel AT91SAM3U4E MCU.
STATUS: The basic AT91SAM3U port was released in NuttX version 5.1.
The basic port includes boot-up logic, interrupt driven serial
console, and system timer interrupts. That release passes the
NuttX OS test and is proven to have a valid OS implementation. A
onfiguration to support the NuttShell is also included.
arch/arm/include/stm32 and arch/arm/src/stm32
These directories contain support for the STMicro STM32 family, particularly
for the STM32F103ZET6.
STATUS: The basic STM32 port was released in NuttX version 0.4.12.
The basic port includes boot-up logic, interrupt driven serial console,
and system timer interrupts. The 0.4.13 release added support for SPI,
serial FLASH, and USB device.; The 4.14 release added support for
buttons and SDIO-based MMC/SD and verifed DMA support. Verified
configurations are available for NuttX OS test, the NuttShell (NSH)
example, the USB serial device class, and the USB mass storage device
lass example.
arch/arm/include/str71x and arch/arm/src/str71x
These directories provide support for the STMicro STR71x processors.
Coding is complete on the basic port (boot logic, system time, serial console),
but no testing has been performed due to some problems I am having with my
JTAG wiggler and OpenOCD on Linux.
arch/avr
This directory is dedicated to ports to the Atmel AVR (8-bit) and AVR32 (32-bit)
MCU families. STATUS: Under development.
arch/avr/include/avr and arch/avr/src/avr
Common support for all 8-bit VR MCUs
arch/avr/include/atmega and arch/avr/src/atmega
Support specifically for the AVR ATMega family (specifically only for
the ATMega128 at the moment).
arch/avr/include/at90usb and arch/avr/src/at90usb
Support specifically for the AVR AT90USB646, 647, 1286, and 1287 family.
arch/avr/include/avr32 and arch/avr/src/avr32
Common support for all AVR32 MCUs
arch/avr/include/at32uc3 and arch/avr/src/at32uc3
Support specifically for the AT32UC3Bxxx family (specifically only for
the AT32UC3B0256 at the moment).
arch/hc
This directory is dedicated to ports to the Freescale HC family.
arch/arm/include/m9s12 and arch/arm/src/m9s12
These directories provide support for the Freescale mc9s12x family.
STATUS: Fragments of this port were first released in nuttx-5.0 and
the port was "code-complete" as nuttx-5.18. However, the final
verification effort has been stalled because of higher priority tasks.
arch/m68322
A work in progress.
STATUS: Stalled for the time being.
arch/mips
This directory is dedicated to ports to the MIPS family.
arch/mips/include/mips32 and arch/mips/src/mips32
Common support for all MIPS32 architectures
arch/mips/include/pic32mx and arch/mips/src/pic32mx
Support for all MicroChip PIC32MX architectures
arch/rgmp
RGMP stands for RTOS and GPOS on Multi-Processor. RGMP is a project
for running GPOS and RTOS simultaneously on multi-processor platforms.
You can port your favorite RTOS to RGMP together with an unmodified
Linux to form a hybrid operating system. This makes your application
able to use both RTOS and GPOS features.
See http://rgmp.sourceforge.net/wiki/index.php/Main_Page for further
information about RGMP.
arch/sh - SuperH and related Hitachi/Renesas microcontrollers
arch/sh/include and arch/sh/src/common
Common SuperH logic.
arch/sh/include/shs and arch/sh/src/sh1
Support for the SH-1 processor.
arch/8051 - 8051/52 microcontrollers
8051 Microcontroller. This port is not quite ready for prime time.
arch/x86 - Intel x86 architectures
This directory holds related, 32- and 64-bit architectures from Intel.
At present, this includes the following subdirectories:
arch/x86/include and arch/x86/src/common
Common x86 logic.
arch/x86/include/i486 and arch/x86/src/i486
These directories hold definitions and logic appropriate for any
instantiation of the 32-bit i486 architecture.
arch/x86/include/qemu and arch/x86/src/qemu
This is the implementation of NuttX on the QEMU x86 simulation.
arch/z16 - ZiLOG 16-bit processors
This directory holds related, 16-bit architectures from ZiLOG. At
present, this includes the following subdirectories:
arch/z16/include and arch/z16/src/common
Common microcontroller logic.
arch/z16/include/z16f and arch/z16/src/z16f
ZiLOG z16f Microcontroller.
STATUS: Released in nuttx-0.3.7. Fully functional other than issues
addressed in ${TOPDIR}/TODO.
arch/z80 - ZiLOG 8-bit microcontrollers
This directory holds related, 8-bit architectures from ZiLOG. At
present, this includes the following subdirectories:
arch/z80/include and arch/z80/src/common
Common microcontroller logic.
arch/z80/include/z80 and arch/z80/src/z80
Classic ZiLOG z80 Microcontroller.
STATUS: Functional with no known defects. There are still several
OS features that have not yet been tested (e.g., networking).
arch/z80/include/z8 and arch/z80/src/z8
ZiLOG Z8Encore! Microcontroller
arch/z80/include/ez80 and arch/z80/src/ez80
ZiLOG ez80 Acclaim! Microcontroller