README
======
This README discusses issues unique to NuttX configurations for the
STMicro STM32F769I-DISCO development board featuring the STM32F769NIH6
MCU. The STM32F769NIH6 is a 216MHz Cortex-M7 operating with 2048K Flash
memory and 512Kb SRAM. The board features:
- On-board ST-LINK/V2 for programming and debugging,
- Mbed-enabled (mbed.org)
- 4-inch 800x472 color LCD-TFT with capacitive touch screen
- SAI audio codec
- Audio line in and line out jack
- Two ST MEMS microphones
- SPDIF RCA input connector
- Two pushbuttons (user and reset)
- 512-Mbit Quad-SPI Flash memory
- 128-Mbit SDRAM
- Connector for microSD card
- RF-EEPROM daughterboard connector
- USB OTG HS with Micro-AB connectors
- Ethernet connector compliant with IEEE-802.3-2002 and PoE
Refer to the http://www.st.com website for further information about this
board (search keyword: stm32f769i-disco)
Contents
========
- STATUS
- Development Environment
- LEDs and Buttons
- Serial Console
- Configurations
STATUS
======
2017-07: The basic NSH configuration is functional using a serial
console on USART1, which is connected to the "virtual com port"
of the ST/LINK USB adapter.
2017-07: STM32 F7 Ethernet appears to be functional, but has had
only light testing.
Work in progress: Use LCD over DSI interface, rest of board.
Development Environment
=======================
The Development environments for the STM32F769I-DISCO board are identical
to the environments for other STM32F boards. For full details on the
environment options and setup, see the README.txt file in the
config/stm32f769i-disco directory.
LEDs and Buttons
================
LEDs
----
The STM32F769I-DISCO board has numerous LEDs but only one, LD3 located
near the reset button, that can be controlled by software.
LD3 is controlled by PI1 which is also the SPI2_SCK at the Arduino
interface. One end of LD3 is grounded so a high output on PI1 will
illuminate the LED.
This LED is not used by the board port unless CONFIG_ARCH_LEDS is defined.
In that case, the usage by the board port is defined in include/board.h
and src/stm32_leds.c. The LEDs are used to encode OS-related events as
follows:
SYMBOL Meaning LD3
------------------- ----------------------- ------
LED_STARTED NuttX has been started OFF
LED_HEAPALLOCATE Heap has been allocated OFF
LED_IRQSENABLED Interrupts enabled OFF
LED_STACKCREATED Idle stack created ON
LED_INIRQ In an interrupt N/C
LED_SIGNAL In a signal handler N/C
LED_ASSERTION An assertion failed N/C
LED_PANIC The system has crashed FLASH
Thus is LD3 is statically on, NuttX has successfully booted and is,
apparently, running normally. If LD3 is flashing at approximately
2Hz, then a fatal error has been detected and the system has halted.
Buttons
-------
Pushbutton B1, labelled "User", is connected to GPIO PI11. A high
value will be sensed when the button is depressed.
Serial Console
==============
Use the serial interface the ST/LINK provides to the USB host.
Configurations
==============
Common Configuration Information
--------------------------------
Each STM32F769I-DISCO configuration is maintained in a sub-directory and
can be selected as follow:
tools/configure.sh stm32f769i-disco/<subdir>
Where <subdir> is one of the sub-directories listed below.
Configuration Directories
-------------------------
nsh:
---
Configures the NuttShell (NSH) located at apps/examples/nsh. The
Configuration enables the serial interfaces on UART1.
Otherwise nothing is enabled, so that config is a starting point
for initial testing.
Support for builtin applications is enabled, but in the base
configuration no builtin applications are selected.
nsh-ehternet:
---
Same as above but a lot more hardware peripherals enabled,
in particular ethernet, as well as networking stuff.
22cd0d47fa