README
======
This README file provides information about the port of NuttX to the NXP
i.MXRT evaluation kit, MIMXRT1050-EVKB. This board features the
MIMXRT1052DVL6A MCU. Some of the features of this board include:
o Processor
- MIMXRT1052DVL6A processor
o Memory
- 256 Mb SDRAM memory
- 512 Mb Hyper Flash
- Footprint for QSPI Flash
- TF socket for SD card
o Display and Audio
- Parallel LCD connector
- Camera connector
- Audio CODEC
- 4-pole audio headphone jack
- External speaker connection
- Microphone
- SPDIF connector
o Connectivity
- Micro USB host and OTG connectors
- Ethernet (10/100T) connector
- CAN transceivers
- Arduino® interface
Contents
========
o Serial Console
o LEDs and buttons
o Configurations
- Configuration sub-directories
Serial Console
==============
To be provided.
GPIO_AD_B0_12 LPUART1_TX UART Console
GPIO_AD_B0_13 LPUART1_RX UART Console
LEDs and buttons
================
LEDs
----
There are four LED status indicators located on the EVK Board. The
functions of these LEDs include:
- Main Power Supply(D3)
Green: DC 5V main supply is normal.
Red: J2 input voltage is over 5.6V.
Off: The board is not powered.
- Reset RED LED(D15)
- OpenSDA LED(D16)
- USER LED(D18)
Only a single LED, D18, is under software control. It connects to
GPIO_AD_B0_09 which is shared with JTAG_TDI and ENET_RST
This LED is not used by the board port unless CONFIG_ARCH_LEDS is
defined. In that case, the usage by the board port is defined in
include/board.h and src/sam_autoleds.c. The LED is used to encode
OS-related events as follows:
------------------- ----------------------- ------
SYMBOL Meaning LED
------------------- ----------------------- ------
LED_STARTED NuttX has been started OFF
LED_HEAPALLOCATE Heap has been allocated OFF
LED_IRQSENABLED Interrupts enabled OFF
LED_STACKCREATED Idle stack created ON
LED_INIRQ In an interrupt N/C
LED_SIGNAL In a signal handler N/C
LED_ASSERTION An assertion failed N/C
LED_PANIC The system has crashed FLASH
Thus if the LED is statically on, NuttX has successfully booted and is,
apparently, running normally. If the LED is flashing at approximately
2Hz, then a fatal error has been detected and the system has halted.
Buttons
-------
There are four user interface switches on the MIMXRT1050 EVK Board:
- SW1: Power Switch (slide switch)
- SW2: ON/OFF Button
- SW3: Reset button
- SW8: User button
Only the user button is available to the software. It is sensed on the
WAKEUP pin which will be pulled low when the button is pressed.
Configurations
==============
Information Common to All Configurations
----------------------------------------
Each i.MX RT 10050 configuration is maintained in a sub-directory and
can be selected as follow:
tools/configure.sh [OPTIONS] imxrt1050-evk/<subdir>
Where typical options are -l to configure to build on Linux or -c to
configure for Cygwin under Linux. 'tools/configure.sh -h' will show
you all of the options.
Before building, make sure the PATH environment variable include the
correct path to the directory than holds your toolchain binaries.
And then build NuttX by simply typing the following. At the conclusion of
the make, the nuttx binary will reside in an ELF file called, simply, nuttx.
make
The <subdir> that is provided above as an argument to the tools/configure.sh
must be is one of the following.
NOTES:
1. These configurations use the mconf-based configuration tool. To
change any of these configurations using that tool, you should:
a. Build and install the kconfig-mconf tool. See nuttx/README.txt
see additional README.txt files in the NuttX tools repository.
b. Execute 'make menuconfig' in nuttx/ in order to start the
reconfiguration process.
2. Unless stated otherwise, all configurations generate console
output on UART3 (i.e., for the Arduino serial shield).
3. All of these configurations are set up to build under Windows using the
"GNU Tools for ARM Embedded Processors" that is maintained by ARM
(unless stated otherwise in the description of the configuration).
https://developer.arm.com/open-source/gnu-toolchain/gnu-rm
That toolchain selection can easily be reconfigured using
'make menuconfig'. Here are the relevant current settings:
Build Setup:
CONFIG_HOST_WINDOWS=y : Window environment
CONFIG_WINDOWS_CYGWIN=y : Cywin under Windows
System Type -> Toolchain:
CONFIG_ARMV7M_TOOLCHAIN_GNU_EABIW=y : GNU ARM EABI toolchain
Configuration sub-directories
-----------------------------
nsh:
Configures the NuttShell (nsh) located at examples/nsh. This NSH
configuration is focused on low level, command-line driver testing.
It has no network.
