477 lines
17 KiB
C
477 lines
17 KiB
C
/************************************************************************************
|
|
* configs/open1788/include/board.h
|
|
* include/arch/board/board.h
|
|
*
|
|
* Copyright (C) 2013 Gregory Nutt. All rights reserved.
|
|
* Author: Gregory Nutt <gnutt@nuttx.org>
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
*
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in
|
|
* the documentation and/or other materials provided with the
|
|
* distribution.
|
|
* 3. Neither the name NuttX nor the names of its contributors may be
|
|
* used to endorse or promote products derived from this software
|
|
* without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
|
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
|
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
|
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
|
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
|
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
|
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
|
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
|
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
|
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
|
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
|
* POSSIBILITY OF SUCH DAMAGE.
|
|
*
|
|
************************************************************************************/
|
|
|
|
#ifndef __CONFIG_OPEN1788_INCLUDE_BOARD_H
|
|
#define __CONFIG_OPEN1788_INCLUDE_BOARD_H
|
|
|
|
/************************************************************************************
|
|
* Included Files
|
|
************************************************************************************/
|
|
|
|
#include <nuttx/config.h>
|
|
|
|
#include <stdbool.h>
|
|
|
|
#if defined(CONFIG_ARCH_IRQBUTTONS) && defined(CONFIG_LPC17_GPIOIRQ)
|
|
# include <nuttx/irq.h>
|
|
#endif
|
|
|
|
/************************************************************************************
|
|
* Pre-processor Definitions
|
|
************************************************************************************/
|
|
/* Clocking *************************************************************************/
|
|
/* NOTE: The following definitions require lpc17_syscon.h. It is not included here
|
|
* because the including C file may not have that file in its include path.
|
|
*/
|
|
|
|
#define BOARD_XTAL_FREQUENCY (12000000) /* XTAL oscillator frequency */
|
|
#define BOARD_OSCCLK_FREQUENCY BOARD_XTAL_FREQUENCY /* Main oscillator frequency */
|
|
#define BOARD_RTCCLK_FREQUENCY (32768) /* RTC oscillator frequency */
|
|
#define BOARD_INTRCOSC_FREQUENCY (4000000) /* Internal RC oscillator frequency */
|
|
#define BOARD_WDTOSC_FREQUENCY (500000) /* WDT oscillator frequency */
|
|
|
|
/* This is the clock setup we configure for:
|
|
*
|
|
* SYSCLK = BOARD_OSCCLK_FREQUENCY = 12MHz -> Select Main oscillator for source
|
|
* PLL0CLK = (10 * SYSCLK) / 1 = 120MHz -> PLL0 multipler=10, pre-divider=1
|
|
* CCLCK = 120MHz -> CCLK divider = 1
|
|
*/
|
|
|
|
#define LPC17_CCLK 120000000 /* 120Mhz */
|
|
#define BOARD_PCLKDIV 2 /* Peripheral clock = LPC17_CCLK/2 */
|
|
#define BOARD_PCLK_FREQUENCY (LPC17_CCLK / BOARD_PCLKDIV)
|
|
|
|
/* Select the main oscillator as the frequency source. SYSCLK is then the frequency
|
|
* of the main oscillator.
|
|
*
|
|
* If BOARD_XTAL_FREQUENCY > 15000000, then the SCS OSCRS bit (bit 4) should also
|
|
* be set in the BOARD_SCS_VALUE.
|
|
*/
|
|
|
|
#undef CONFIG_LPC17_MAINOSC
|
|
#define CONFIG_LPC17_MAINOSC 1
|
|
#define BOARD_SCS_VALUE SYSCON_SCS_OSCEN
|
|
|
|
/* Select the main oscillator and CCLK divider. The output of the divider is CCLK.
|
|
* The input to the divider (PLLCLK) will be determined by the PLL output.
|
|
*/
|
|
|
|
#define BOARD_CCLKSEL_DIVIDER 1
|
|
#define BOARD_CCLKSEL_VALUE (BOARD_CCLKSEL_DIVIDER | SYSCON_CCLKSEL_CCLKSEL)
|
|
|
|
/* PLL0. PLL0 is used to generate the CPU clock (PLLCLK).
|
|
*
|
|
* Source clock: Main oscillator
|
|
* PLL0 Multiplier value (M): 10
|
|
* PLL0 Pre-divider value (P): 1
|
|
*
|
|
* PLL0CLK = (M * SYSCLK) = 120MHz
|
|
*/
|
|
|
|
#undef CONFIG_LPC17_PLL0
|
|
#define CONFIG_LPC17_PLL0 1
|
|
#define BOARD_CLKSRCSEL_VALUE SYSCON_CLKSRCSEL_MAIN
|
|
|
|
#define BOARD_PLL0CFG_MSEL 10
|
|
#define BOARD_PLL0CFG_PSEL 1
|
|
#define BOARD_PLL0CFG_VALUE \
|
|
(((BOARD_PLL0CFG_MSEL-1) << SYSCON_PLLCFG_MSEL_SHIFT) | \
|
|
((BOARD_PLL0CFG_PSEL-1) << SYSCON_PLLCFG_PSEL_SHIFT))
|
|
|
|
/* PLL1 : PLL1 is used to generate clock for the USB */
|
|
|
|
#undef CONFIG_LPC17_PLL1
|
|
#define BOARD_PLL1CFG_MSEL 4
|
|
#define BOARD_PLL1CFG_PSEL 2
|
|
#define BOARD_PLL1CFG_VALUE \
|
|
(((BOARD_PLL1CFG_MSEL-1) << SYSCON_PLLCFG_MSEL_SHIFT) | \
|
|
((BOARD_PLL1CFG_PSEL-1) << SYSCON_PLLCFG_PSEL_SHIFT))
|
|
|
|
#ifdef CONFIG_LPC17_EMC
|
|
/* EMC clock selection.
|
|
*
|
|
* The EMC clock should not be driven above 80MHz. As a result the EMC
|
|
* uses the CPU clock divided by two.
|
|
*/
|
|
|
|
# define BOARD_EMCCLKSEL_DIVIDER 2
|
|
# define BOARD_EMCCLKSEL_VALUE SYSCON_EMCCLKSEL_CCLK_DIV2
|
|
# define LPC17_EMCCLK (LPC17_CCLK / BOARD_EMCCLKSEL_DIVIDER)
|
|
#endif
|
|
|
|
#if defined(CONFIG_LPC17_USBHOST) || (CONFIG_LPC17_USBDEV)
|
|
/* USB divider. The output of the PLL is used as the USB clock
|
|
*
|
|
* USBCLK = PLL1CLK = (SYSCLK * 4) = 48MHz
|
|
*/
|
|
|
|
# define BOARD_USBCLKSEL_DIVIDER 1
|
|
# define BOARD_USBCLKSEL_VALUE (SYSCON_USBCLKSEL_USBDIV_DIV1 | \
|
|
SYSCON_USBCLKSEL_USBSEL_PLL1)
|
|
#endif
|
|
|
|
/* FLASH Configuration */
|
|
|
|
#undef CONFIG_LPC17_FLASH
|
|
#define CONFIG_LPC17_FLASH 1
|
|
|
|
/* Flash access use 6 CPU clocks - Safe for any allowed conditions */
|
|
|
|
#define BOARD_FLASHCFG_VALUE (SYSCON_FLASHCFG_TIM_5 | 0x03a)
|
|
|
|
/* Ethernet configuration */
|
|
|
|
#define ETH_MCFG_CLKSEL_DIV ETH_MCFG_CLKSEL_DIV20
|
|
|
|
#ifdef CONFIG_LPC17_SDCARD
|
|
/* SDIO dividers. Note that slower clocking is required when DMA is disabled
|
|
* in order to avoid RX overrun/TX underrun errors due to delayed responses
|
|
* to service FIFOs in interrupt driven mode.
|
|
* SDCARD_CLOCK=PCLK/(2*(SDCARD_CLKDIV+1))
|
|
*/
|
|
|
|
# define SDCARD_CLKDIV_INIT 74 /* 400Khz */
|
|
# define SDCARD_INIT_CLKDIV (SDCARD_CLKDIV_INIT)
|
|
|
|
# define SDCARD_NORMAL_CLKDIV 1 /* DMA ON: SDCARD_CLOCK=15MHz */
|
|
#define SDCARD_SLOW_CLKDIV 14 /* DMA OFF: SDCARD_CLOCK=2MHz */
|
|
|
|
# ifdef CONFIG_SDIO_DMA
|
|
# define SDCARD_MMCXFR_CLKDIV (SDCARD_NORMAL_CLKDIV)
|
|
# else
|
|
# define SDCARD_MMCXFR_CLKDIV (SDCARD_SLOW_CLKDIV)
|
|
# endif
|
|
|
|
# ifdef CONFIG_SDIO_DMA
|
|
# define SDCARD_SDXFR_CLKDIV (SDCARD_NORMAL_CLKDIV)
|
|
# else
|
|
# define SDCARD_SDXFR_CLKDIV (SDCARD_SLOW_CLKDIV)
|
|
# endif
|
|
#endif
|
|
|
|
/* Set EMC delay values:
|
|
*
|
|
* CMDDLY: Programmable delay value for EMC outputs in command delayed
|
|
* mode. The delay amount is roughly CMDDLY * 250 picoseconds.
|
|
* FBCLKDLY: Programmable delay value for the feedback clock that controls
|
|
* input data sampling. The delay amount is roughly (FBCLKDLY+1) * 250
|
|
* picoseconds.
|
|
* CLKOUT0DLY: Programmable delay value for the CLKOUT0 output. This would
|
|
* typically be used in clock delayed mode. The delay amount is roughly
|
|
* (CLKOUT0DLY+1) * 250 picoseconds.
|
|
* CLKOUT1DLY: Programmable delay value for the CLKOUT1 output. This would
|
|
* typically be used in clock delayed mode. The delay amount is roughly
|
|
* (CLKOUT1DLY+1) * 250 picoseconds.
|
|
*
|
|
* Optimal for NOR: {1,1,1,1}
|
|
* Needed for NAND and SDRAM: {17,1,2,1}
|
|
*/
|
|
|
|
#ifdef CONFIG_LPC17_EMC
|
|
#if defined(CONFIG_LPC17_EXTNAND) || defined(CONFIG_LPC17_EXTDRAM)
|
|
# define BOARD_CMDDLY 17
|
|
# define BOARD_FBCLKDLY 17
|
|
# define BOARD_CLKOUT0DLY 1
|
|
# define BOARD_CLKOUT1DLY 1
|
|
#else
|
|
# define BOARD_CMDDLY 1
|
|
# define BOARD_FBCLKDLY 1
|
|
# define BOARD_CLKOUT0DLY 1
|
|
# define BOARD_CLKOUT1DLY 1
|
|
#endif
|
|
#endif
|
|
|
|
/* LED definitions ******************************************************************/
|
|
/* If CONFIG_ARCH_LEDS is not defined, then the user can control the LEDs in
|
|
* any way. The following definitions are used to access individual LEDs.
|
|
*
|
|
* LED1 -- Connected to P1[14]
|
|
* LED2 -- Connected to P0[16] (shared with UART1 RXD)
|
|
* LED3 -- Connected to P1[13]
|
|
* LED4 -- Connected to P4[27]
|
|
*
|
|
* These LEDs are connecte to ground so a high output value will illuminate them.
|
|
*/
|
|
|
|
/* LED index values for use with board_userled() */
|
|
|
|
#define BOARD_LED1 0
|
|
#define BOARD_LED2 1
|
|
#define BOARD_LED3 2
|
|
#define BOARD_LED4 3
|
|
#define BOARD_NLEDS 4
|
|
|
|
/* LED bits for use with board_userled_all() */
|
|
|
|
#define BOARD_LED1_BIT (1 << BOARD_LED1)
|
|
#define BOARD_LED2_BIT (1 << BOARD_LED2)
|
|
#define BOARD_LED3_BIT (1 << BOARD_LED3)
|
|
#define BOARD_LED4_BIT (1 << BOARD_LED4)
|
|
|
|
/* If CONFIG_ARCH_LEDs is defined, then NuttX will control the four LEDs
|
|
* on the WaveShare Open1788K. The following definitions describe how NuttX
|
|
* controls the LEDs:
|
|
*/
|
|
/* LED1 LED2 LED3 LED4 */
|
|
#define LED_STARTED 0 /* OFF OFF OFF OFF */
|
|
#define LED_HEAPALLOCATE 1 /* ON OFF OFF OFF */
|
|
#define LED_IRQSENABLED 2 /* OFF ON OFF OFF */
|
|
#define LED_STACKCREATED 3 /* ON ON OFF OFF */
|
|
#define LED_INIRQ 4 /* LED3 glows, on while in interrupt */
|
|
#define LED_SIGNAL 4 /* LED3 glows, on while in signal handler */
|
|
#define LED_ASSERTION 4 /* LED3 glows, on while in assertion */
|
|
#define LED_PANIC 4 /* LED3 Flashes at 2Hz */
|
|
#define LED_IDLE 5 /* LED4 glows: ON while active *
|
|
* OFF while sleeping */
|
|
|
|
/* Button definitions ***************************************************************/
|
|
/* The Open1788 supports several buttons. All must be pulled up by the Open1788.
|
|
* When closed, the pins will be pulled to ground. So the buttons will read "1"
|
|
* when open and "0" when closed. All except USER1 are capable of generating
|
|
* interrupts.
|
|
*
|
|
* USER1 -- Connected to P4[26]
|
|
* USER2 -- Connected to P2[22]
|
|
* USER3 -- Connected to P0[10]
|
|
*
|
|
* And a Joystick
|
|
*
|
|
* JOY_A -- Connected to P2[25]
|
|
* JOY_B -- Connected to P2[26]
|
|
* JOY_C -- Connected to P2[23]
|
|
* JOY_D -- Connected to P2[19]
|
|
* JOY_CTR -- Connected to P0[14] (shared with SSP1 SSEL)
|
|
*
|
|
* For the interrupting buttons, interrupts are generated on both edges (press and
|
|
* release).
|
|
*/
|
|
|
|
|
|
#define BOARD_BUTTON_USER1 0
|
|
#define BOARD_BUTTON_USER2 1
|
|
#define BOARD_BUTTON_USER3 2
|
|
|
|
#define BOARD_JOYSTICK_A 3
|
|
#define BOARD_JOYSTICK_B 4
|
|
#define BOARD_JOYSTICK_C 5
|
|
#define BOARD_JOYSTICK_D 6
|
|
#define BOARD_JOYSTICK_CTR 7
|
|
|
|
#define BOARD_NUM_BUTTONS 8
|
|
|
|
#define BOARD_BUTTON_USER1_BIT (1 << BOARD_BUTTON_USER1)
|
|
#define BOARD_BUTTON_USER2_BIT (1 << BOARD_BUTTON_USER2)
|
|
#define BOARD_BUTTON_USER3_BIT (1 << BOARD_BUTTON_USER3)
|
|
|
|
#define BOARD_JOYSTICK_A_BIT (1 << BOARD_JOYSTICK_A)
|
|
#define BOARD_JOYSTICK_B_BIT (1 << BOARD_JOYSTICK_B)
|
|
#define BOARD_JOYSTICK_C_BIT (1 << BOARD_JOYSTICK_C)
|
|
#define BOARD_JOYSTICK_D_BIT (1 << BOARD_JOYSTICK_D)
|
|
#define BOARD_JOYSTICK_CTR_BIT (1 << BOARD_JOYSTICK_CTR)
|
|
|
|
/* Alternate pin selections *********************************************************/
|
|
|
|
/* UART0:
|
|
*
|
|
* TX --- Connected to P0[2]
|
|
* RX --- Connected to P0[3]
|
|
*/
|
|
|
|
#define GPIO_UART0_TXD GPIO_UART0_TXD_2
|
|
#define GPIO_UART0_RXD GPIO_UART0_RXD_2
|
|
|
|
/* UART1:
|
|
*
|
|
* All pin options are controlled by older briges on the bottom of the board. There
|
|
* are the default settings on my board as it came out of the box:
|
|
*
|
|
* RTS --- Connected to P0[22]
|
|
* RI --- Connected to P0[21]
|
|
* DSR --- Connected to P0[19]
|
|
* DCD --- Connected to P0[18]
|
|
* CTS --- Connected to P0[17]
|
|
* DTR --- Connected to P0[20]
|
|
* TXD --- Connected to P0[15]
|
|
* RXD --- Connected to P0[16] (Shared with LED2)
|
|
*/
|
|
|
|
#define GPIO_UART1_RTS GPIO_UART1_RTS_2
|
|
#define GPIO_UART1_RI GPIO_UART1_RI_1
|
|
#define GPIO_UART1_DSR GPIO_UART1_DSR_1
|
|
#define GPIO_UART1_DCD GPIO_UART1_DCD_1
|
|
#define GPIO_UART1_CTS GPIO_UART1_CTS_1
|
|
#define GPIO_UART1_DTR GPIO_UART1_DTR_1
|
|
#define GPIO_UART1_TXD GPIO_UART1_TXD_1
|
|
#define GPIO_UART1_RXD GPIO_UART1_RXD_1
|
|
|
|
/* MCI-SDIO:
|
|
*
|
|
* D0 --- Connected to P1[6]
|
|
* D1 --- Connected to P2[11]
|
|
* D2 --- Connected to P2[12]
|
|
* D3 --- Connected to P2[13]
|
|
* CLK --- Connected to P1[2]
|
|
* CMD --- Connected to P1[3]
|
|
*/
|
|
|
|
#define GPIO_SD_DAT0 GPIO_SD_DAT0_2
|
|
#define GPIO_SD_DAT1 GPIO_SD_DAT1_2
|
|
#define GPIO_SD_DAT2 GPIO_SD_DAT2_2
|
|
#define GPIO_SD_DAT3 GPIO_SD_DAT3_2
|
|
#define GPIO_SD_CLK GPIO_SD_CLK_2
|
|
#define GPIO_SD_CMD GPIO_SD_CMD_2
|
|
|
|
/* LCD R:
|
|
*
|
|
* VD0 --- Connected to P0[4]
|
|
* VD1 --- Connected to P0[5]
|
|
* VD2 --- Connected to P4[28]
|
|
* VD3 --- Connected to P4[29]
|
|
* VD4 --- Connected to P2[6]
|
|
* VD5 --- Connected to P2[7]
|
|
* VD6 --- Connected to P2[8]
|
|
* VD7 --- Connected to P2[9]
|
|
*/
|
|
|
|
#define GPIO_LCD_VD0 GPIO_LCD_VD0_1
|
|
#define GPIO_LCD_VD1 GPIO_LCD_VD1_1
|
|
#define GPIO_LCD_VD2 GPIO_LCD_VD2_2
|
|
#define GPIO_LCD_VD3 GPIO_LCD_VD3_3
|
|
#define GPIO_LCD_VD4 GPIO_LCD_VD4_1
|
|
#define GPIO_LCD_VD5 GPIO_LCD_VD5_1
|
|
#define GPIO_LCD_VD6 GPIO_LCD_VD6_2
|
|
#define GPIO_LCD_VD7 GPIO_LCD_VD7_2
|
|
|
|
/* LCD G:
|
|
*
|
|
* VD8 --- Connected to P0[6]
|
|
* VD9 --- Connected to P0[7]
|
|
* VD10 --- Connected to P1[20]
|
|
* VD11 --- Connected to P1[21]
|
|
* VD12 --- Connected to P1[22]
|
|
* VD13 --- Connected to P1[23]
|
|
* VD14 --- Connected to P1[24]
|
|
* VD15 --- Connected to P1[25]
|
|
*/
|
|
|
|
#define GPIO_LCD_VD8 GPIO_LCD_VD8_1
|
|
#define GPIO_LCD_VD9 GPIO_LCD_VD9_1
|
|
#define GPIO_LCD_VD10 GPIO_LCD_VD10_1
|
|
#define GPIO_LCD_VD11 GPIO_LCD_VD11_1
|
|
#define GPIO_LCD_VD12 GPIO_LCD_VD12_1
|
|
#define GPIO_LCD_VD13 GPIO_LCD_VD13_1
|
|
#define GPIO_LCD_VD14 GPIO_LCD_VD14_1
|
|
#define GPIO_LCD_VD15 GPIO_LCD_VD15_1
|
|
|
|
/* LCD B:
|
|
*
|
|
* VD16 --- Connected to P0[8]
|
|
* VD17 --- Connected to P0[9]
|
|
* VD18 --- Connected to P2[12]
|
|
* VD19 --- Connected to P2[13]
|
|
* VD20 --- Connected to P1[26]
|
|
* VD21 --- Connected to P1[27]
|
|
* VD22 --- Connected to P1[28]
|
|
* VD23 --- Connected to P1[29]
|
|
*
|
|
* DCLK --- Connected to P2[2]
|
|
* LP --- Connected to P2[5]
|
|
* FP --- Connected to P2[3]
|
|
* ENAB_M --- Connected to P2[4]
|
|
* PWR --- Connected to P2[0]
|
|
*/
|
|
|
|
/* XPT2046 Touchscreen:
|
|
*
|
|
/* -------------- -------------------- ------------ --------------------------------
|
|
* XTPT2046 Module Module Open1788 LED
|
|
* Signal Connector Connector
|
|
* -------------- -------------------- ------------ ---------------------------------
|
|
* Pin 11 PENIRQ\ PENIRQ (pulled high) PORT3 Pin 1 P2.15 PENIRQ
|
|
* Pin 12 DOUT MISO PORT3 Pin 4 P1.18 MISO1 (Also USB HOST UP LED)
|
|
* Pin 13 BUSY BUSY (pulled high) PORT3 Pin 9 P2.14 BUSY
|
|
* Pin 14 DIN MOSI PORT3 Pin 3 P0.13 MOSI1 (Also USB Device up LED and SD CD pin)
|
|
* Pin 15 CS\ SSEL (pulled high) PORT3 Pin 6 P1.8 GPIO (Also RMII_CRS_DV)
|
|
* Pin 16 DCLK SCK PORT3 Pin 5 P1.19 SCK1
|
|
* -------------- -------------------- ------------ ---------------------------------
|
|
*/
|
|
|
|
|
|
#define GPIO_SSP1_MISO GPIO_SSP1_MISO_3
|
|
#define GPIO_SSP1_MOSI GPIO_SSP1_MOSI_2
|
|
#define GPIO_SSP1_SCK GPIO_SSP1_SCK_2
|
|
|
|
/************************************************************************************
|
|
* Public Types
|
|
************************************************************************************/
|
|
|
|
#ifndef __ASSEMBLY__
|
|
|
|
/************************************************************************************
|
|
* Public Data
|
|
************************************************************************************/
|
|
|
|
#undef EXTERN
|
|
#if defined(__cplusplus)
|
|
#define EXTERN extern "C"
|
|
extern "C" {
|
|
#else
|
|
#define EXTERN extern
|
|
#endif
|
|
|
|
/************************************************************************************
|
|
* Public Function Prototypes
|
|
************************************************************************************/
|
|
/************************************************************************************
|
|
* Name: lpc17_boardinitialize
|
|
*
|
|
* Description:
|
|
* All LPC17xx architectures must provide the following entry point. This entry
|
|
* point is called early in the intitialization -- after all memory has been
|
|
* configured and mapped but before any devices have been initialized.
|
|
*
|
|
************************************************************************************/
|
|
|
|
void lpc17_boardinitialize(void);
|
|
|
|
#undef EXTERN
|
|
#if defined(__cplusplus)
|
|
}
|
|
#endif
|
|
|
|
#endif /* __ASSEMBLY__ */
|
|
#endif /* __CONFIG_OPEN1788_INCLUDE_BOARD_H */
|