176 lines
8.8 KiB
C
176 lines
8.8 KiB
C
/****************************************************************************
|
|
* drivers/mmcsd/mmcsd_spi.h
|
|
*
|
|
* Licensed to the Apache Software Foundation (ASF) under one or more
|
|
* contributor license agreements. See the NOTICE file distributed with
|
|
* this work for additional information regarding copyright ownership. The
|
|
* ASF licenses this file to you under the Apache License, Version 2.0 (the
|
|
* "License"); you may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at
|
|
*
|
|
* http://www.apache.org/licenses/LICENSE-2.0
|
|
*
|
|
* Unless required by applicable law or agreed to in writing, software
|
|
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
|
|
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
|
|
* License for the specific language governing permissions and limitations
|
|
* under the License.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#ifndef __DRIVERS_MMCSD_MMCSD_SPI_H
|
|
#define __DRIVERS_MMCSD_MMCSD_SPI_H
|
|
|
|
/****************************************************************************
|
|
* Included Files
|
|
****************************************************************************/
|
|
|
|
#include <nuttx/config.h>
|
|
|
|
/****************************************************************************
|
|
* Pre-processor Definitions
|
|
****************************************************************************/
|
|
|
|
/* SPI **********************************************************************/
|
|
|
|
/* SPI Command Set */
|
|
|
|
#define CMD0 0x40 /* GO_IDLE_STATE: Resets all cards to idle state */
|
|
#define CMD1 0x41 /* SEND_OP_COND: Sends capacity support information */
|
|
#define CMD6 0x46 /* SWITCH_FUNC: Checks switchable function */
|
|
#define CMD8 0x48 /* SEND_IF_COND: Sends SD Memory Card interface condition */
|
|
#define CMD9 0x49 /* SEND_CSD: Asks card to send its card specific data (CSD) */
|
|
#define CMD10 0x4a /* SEND_CID: Asks card to send its card identification (CID) */
|
|
#define CMD12 0x4c /* STOP_TRANSMISSION: Forces the card to stop transmission */
|
|
#define CMD13 0x4d /* SEND_STATUS: Asks card to send its status register */
|
|
#define CMD16 0x50 /* SET_BLOCKLEN: Sets a block length (in bytes) */
|
|
#define CMD17 0x51 /* READ_SINGLE_BLOCK: Reads a block of the selected size */
|
|
#define CMD18 0x52 /* READ_MULTIPLE_BLOCK: Continuously transfers blocks from card to host */
|
|
#define CMD20 0x54 /* CMD_WRITEBLOCK: Write block to memory (MMC) */
|
|
#define CMD24 0x58 /* WRITE_BLOCK: Writes a block of the selected size */
|
|
#define CMD25 0x59 /* WRITE_MULTIPLE_BLOCK: Continuously writes blocks of data */
|
|
#define CMD27 0x5b /* PROGRAM_CSD: Set programmable bits of the CSD */
|
|
#define CMD28 0x5c /* SET_WRITE_PROT: Sets the write protection bit of group */
|
|
#define CMD29 0x5d /* CLR_WRITE_PROT: Clears the write protection bit of group */
|
|
#define CMD30 0x5e /* SEND_WRITE_PROT: Asks card to send state of write protection bits */
|
|
#define CMD32 0x60 /* ERASE_WR_BLK_START_ADDR: Sets address of first block to erase */
|
|
#define CMD33 0x61 /* ERASE_WR_BLK_END_ADDR: Sets address of last block to erase */
|
|
#define CMD34 0x62 /* UNTAG_SECTOR: (MMC) */
|
|
#define CMD35 0x63 /* TAG_ERASE_GROUP_START: (MMC) */
|
|
#define CMD36 0x64 /* TAG_ERASE_GOUPR_END: (MMC) */
|
|
#define CMD37 0x65 /* UNTAG_ERASE_GROUP: (MMC) */
|
|
#define CMD38 0x66 /* ERASE: Erases all previously selected write blocks */
|
|
#define CMD40 0x68 /* CRC_ON_OFF: (MMC) */
|
|
#define CMD42 0x6a /* LOCK_UNLOCK: Used to Set/Reset the Password or lock/unlock card */
|
|
#define CMD55 0x77 /* APP_CMD: Tells card that the next command is an application specific command */
|
|
#define CMD56 0x78 /* GEN_CMD: Used transfer a block to or get block from card */
|
|
#define CMD58 0x7a /* READ_OCR :Reads the OCR register of a card */
|
|
#define CMD59 0x7b /* CRC_ON_OFF: Turns the CRC option on or off */
|
|
#define ACMD13 0x4d /* SD_STATUS: Send the SD Status */
|
|
#define ACMD22 0x56 /* SEND_NUM_WR_BLOCKS: Send number of the errorfree blocks */
|
|
#define ACMD23 0x57 /* SET_WR_BLK_ERASE_COUNT: Set number blocks to erase before writing */
|
|
#define ACMD41 0x69 /* SD_SEND_OP_COND: Sends host capacity support information */
|
|
#define ACMD42 0x6a /* SET_CLR_CARD_DETECT: Connect/disconnect pull-up resistor on CS */
|
|
#define ACMD51 0x73 /* SEND_SCR: Reads the SD Configuration Register (SCR) */
|
|
|
|
/* SPI 8-bit R1 response */
|
|
|
|
#define MMCSD_SPIR1_OK 0x00 /* No error bits set */
|
|
#define MMCSD_SPIR1_IDLESTATE 0x01 /* Idle state */
|
|
#define MMCSD_SPIR1_ERASERESET 0x02 /* Erase reset */
|
|
#define MMCSD_SPIR1_ILLEGALCMD 0x04 /* Illegal command */
|
|
#define MMCSD_SPIR1_CRCERROR 0x08 /* Com CRC error */
|
|
#define MMCSD_SPIR1_ERASEERROR 0x10 /* Erase sequence error */
|
|
#define MMCSD_SPIR1_ADDRERROR 0x20 /* Address error */
|
|
#define MMCSD_SPIR1_PARAMERROR 0x40 /* Parameter error */
|
|
|
|
/* SPI 8-bit R2 response */
|
|
|
|
#define MMCSD_SPIR2_CARDLOCKED 0x0001 /* Card is locked */
|
|
#define MMCSD_SPIR2_WPERASESKIP 0x0002 /* WP erase skip */
|
|
#define MMCSD_SPIR2_LOCKFAIL 0x0002 /* Lock/unlock cmd failed */
|
|
#define MMCSD_SPIR2_ERROR 0x0004 /* Error */
|
|
#define MMCSD_SPIR2_CCERROR 0x0008 /* CC error */
|
|
#define MMCSD_SPIR2_CARDECCFAIL 0x0010 /* Card ECC failed */
|
|
#define MMCSD_SPIR2_WPVIOLATION 0x0020 /* WP violation */
|
|
#define MMCSD_SPIR2_ERASEPARAM 0x0040 /* Erase parameter */
|
|
#define MMCSD_SPIR2_OUTOFRANGE 0x0080 /* Out of range */
|
|
#define MMCSD_SPIR2_CSDOVERWRITE 0x0080 /* CSD overwrite */
|
|
#define MMCSD_SPIR2_IDLESTATE 0x0100 /* In idle state */
|
|
#define MMCSD_SPIR2_ERASERESET 0x0200 /* Erase reset */
|
|
#define MMCSD_SPIR2_ILLEGALCMD 0x0400 /* Illegal command */
|
|
#define MMCSD_SPIR2_CRCERROR 0x0800 /* Com CRC error */
|
|
#define MMCSD_SPIR2_ERASEERROR 0x1000 /* Erase sequence error */
|
|
#define MMCSD_SPIR2_ADDRERROR 0x2000 /* Address error */
|
|
#define MMCSD_SPIR2_PARAMERROR 0x4000 /* Parameter error */
|
|
|
|
/* Last 4 bytes of the 5 byte R7 response */
|
|
|
|
#define MMCSD_SPIR7_VERSION_SHIFT (28) /* Bits 28-31: Command version number */
|
|
#define MMCSD_SPIR7_VERSION_MASK ((uint32_t)0x0f << MMCSD_SPIR7_VERSION_SHIFT)
|
|
#define MMCSD_SPIR7_VOLTAGE_SHIFT (8) /* Bits 8-11: Voltage accepted */
|
|
#define MMCSD_SPIR7_VOLTAGE_MASK ((uint32_t)0x0f << MMCSD_SPIR7_VOLTAGE_SHIFT)
|
|
|
|
#define MMCSD_SPIR7_VOLTAGE_27 ((uint32_t)0x01 << MMCSD_SPIR7_VOLTAGE_SHIFT) /* 2.7-3.6V */
|
|
|
|
#define MMCSD_SPIR7_ECHO_SHIFT (0) /* Bits 0-7: Echoed check pattern */
|
|
#define MMCSD_SPIR7_ECHO_MASK ((uint32_t)0xff << MMCSD_SPIR7_ECHO_SHIFT)
|
|
|
|
/* Data Response */
|
|
|
|
#define MMCSD_SPIDR_MASK 0x1f /* Mask for valid data response bits */
|
|
#define MMCSD_SPIDR_ACCEPTED 0x05 /* Data accepted */
|
|
#define MMCSD_SPIDR_CRCERROR 0x0b /* Data rejected due to CRC error */
|
|
#define MMCSD_SPIDR_WRERROR 0x0d /* Data rejected due to write error */
|
|
|
|
/* Data Tokens */
|
|
|
|
#define MMCSD_SPIDT_STARTBLKSNGL 0xfe /* First byte of block, single block */
|
|
#define MMCSD_SPIDT_STARTBLKMULTI 0xfc /* First byte of block, multi-block */
|
|
#define MMCSD_SPIDT_STOPTRANS 0xfd /* Stop transmission */
|
|
|
|
/* Data error token */
|
|
|
|
#define MMCSD_SPIDET_UPPER 0xf0 /* The upper four bits are zero */
|
|
#define MMCSD_SPIDET_ERROR 0x01 /* Error */
|
|
#define MMCSD_SPIDET_CCERROR 0x02 /* CC error */
|
|
#define MMCSD_SPIDET_CARDECCFAIL 0x04 /* Card ECC failed */
|
|
#define MMCSD_SPIDET_OUTOFRANGE 0x08 /* Out of range */
|
|
|
|
/* Operating Conditions register */
|
|
|
|
#define MMCSD_OCR_V27 ((uint32_t)1 << 15) /* Bit 15: 2.7-2.8V */
|
|
#define MMCSD_OCR_V28 ((uint32_t)1 << 16) /* Bit 16: 2.8-2.9V */
|
|
#define MMCSD_OCR_V29 ((uint32_t)1 << 17) /* Bit 17: 2.9-3.0V */
|
|
#define MMCSD_OCR_V30 ((uint32_t)1 << 18) /* Bit 18: 3.0-3.1V */
|
|
#define MMCSD_OCR_V31 ((uint32_t)1 << 19) /* Bit 19: 3.1-3.2V */
|
|
#define MMCSD_OCR_V32 ((uint32_t)1 << 20) /* Bit 20: 3.2-3.3V */
|
|
#define MMCSD_OCR_V33 ((uint32_t)1 << 21) /* Bit 21: 3.3-3.4V */
|
|
#define MMCSD_OCR_V34 ((uint32_t)1 << 22) /* Bit 22: 3.4-3.5V */
|
|
#define MMCSD_OCR_V35 ((uint32_t)1 << 23) /* Bit 23: 3.5-3.6V */
|
|
#define MMCSD_OCR_CCS ((uint32_t)1 << 30) /* Bit 30: Card capacity status */
|
|
#define MMCSD_OCR_BUSY ((uint32_t)1 << 31) /* Bit 31: Card powered up status bit */
|
|
|
|
/****************************************************************************
|
|
* Public Types
|
|
****************************************************************************/
|
|
|
|
/****************************************************************************
|
|
* Public Functions Definitions
|
|
****************************************************************************/
|
|
|
|
#undef EXTERN
|
|
#if defined(__cplusplus)
|
|
#define EXTERN extern "C"
|
|
extern "C"
|
|
{
|
|
#else
|
|
#define EXTERN extern
|
|
#endif
|
|
|
|
#undef EXTERN
|
|
#if defined(__cplusplus)
|
|
}
|
|
#endif
|
|
#endif /* __DRIVERS_MMCSD_MMCSD_SPI_H */
|