nuttx/drivers/mtd/Kconfig

#
# For a description of the syntax of this configuration file,
# see the file kconfig-language.txt in the NuttX tools repository.
#

menuconfig MTD
	bool "Memory Technology Device (MTD) Support"
	default n
	---help---
		Memory Technology Device (MTD) drivers.  Some simple drivers for
		memory technologies like FLASH, EEPROM, NVRAM, etc.  See
		include/nuttx/mtd/mtd.h

		(Note: This is a simple memory interface and should not be
		confused with the "real" MTD developed at infradead.org.  This
		logic is unrelated; I just used the name MTD because I am not
		aware of any other common way to refer to this class of devices).

if MTD

config MTD_PARTITION
	bool "Support MTD partitions"
	default n
	---help---
		MTD partitions are build as MTD drivers that manage a sub-region
		of the FLASH memory.  The contain the original FLASH MTD driver and
		simply manage all accesses to assure that (1) FLASH accesses are
		always offset to the beginning of the partition, and (2) that FLASH
		accesses do not extend outside of the partition.

		A FLASH device may be broken up into several partitions managed,
		each managed by a separate MTD driver.  The MTD partition interface
		is described in:

			include/nuttx/mtd/mtd.h
			FAR struct mtd_dev_s *mtd_partition(FAR struct mtd_dev_s *mtd, off_t offset, off_t nblocks);

		Each call to mtd_partition() will create a new MTD driver instance
		managing the sub-region of flash beginning at 'offset' (in blocks)
		and of size 'nblocks' on the device specified by 'mtd'.

config FTL_WRITEBUFFER
	bool "Enable write buffering in the FTL layer"
	default n
	depends on DRVR_WRITEBUFFER

config FTL_READAHEAD
	bool "Enable read-ahead buffering in the FTL layer"
	default n
	depends on DRVR_READAHEAD

config MTD_SECT512
	bool "512B sector conversion"
	default n
	---help---
		If enabled, a MTD driver will be created that will convert the
		sector size of any other MTD driver to a 512 byte "apparent" sector
		size.  The managed MTD driver in this case must have an erase block
		size that is greater than 512B and an even multiple of 512B.

if MTD_SECT512

config MTD_SECT512_ERASED_STATE
	hex "Erased state of the FLASH"
	default 0xff

config MTD_SECT512_READONLY
	bool "512B read-only"
	default n

endif # MTD_SECT512

config MTD_PARTITION_NAMES
	bool "Support MTD partition naming"
	depends on FS_PROCFS
	depends on MTD_PARTITION
	default n
	---help---
		MTD partitions can be assigned a name for reporting via the procfs
		file system interface.  This adds an API which must be called to
		specify the partition name.

config MTD_BYTE_WRITE
	bool "Byte write"
	default n
	---help---
		Some devices (such as the EON EN25F80) support writing an arbitrary
		number of bytes to FLASH. This setting enables MTD interfaces to
		support such writes.  The SMART file system can take advantage of
		this option if it is enabled.

config MTD_WRBUFFER
	bool "Enable MTD write buffering"
	default n
	depends on DRVR_WRITEBUFFER
	select DRVR_INVALIDATE
	select DRVR_READBYTES
	---help---
		Build the mtd_rwbuffer layer and enable support for write buffering.

if MTD_WRBUFFER

config MTD_NWRBLOCKS
	int "MTD write buffer size"
	default 4
	---help---
		The size of the MTD write buffer (in blocks)

endif # MTD_WRBUFFER

config MTD_READAHEAD
	bool "Enable MTD read-ahead buffering"
	default n
	depends on DRVR_READAHEAD
	select DRVR_INVALIDATE
	select DRVR_READBYTES
	---help---
		Build the mtd_rwbuffer layer and enable support for read-ahead buffering.

if MTD_READAHEAD

config MTD_NRDBLOCKS
	int "MTD read-head buffer size"
	default 4
	---help---
		The size of the MTD read-ahead buffer (in blocks)

endif # MTD_READAHEAD

config MTD_PROGMEM
	bool "Enable on-chip program FLASH MTD device"
	default n
	depends on ARCH_HAVE_PROGMEM
	---help---
		Enable to support an MTD device that supports the on-chip FLASH
		using the interfaces defined in include/nuttx/progmem.  Those
		interfaces must be exported by chip-specific logic.

if MTD_PROGMEM

config MTD_PROGMEM_ERASESTATE
	bool "Enable FLASH MTD device erasestate"
	depends on ARCH_HAVE_PROGMEM_ERASESTATE
	---help---
		Enable the ioctl MTDIOCTL_PROGMEM_ERASESTATE command in the on-chip
		FLASH interface.
		
endif #MTD_PROGMEM

config MTD_CONFIG
	bool "Enable Dev Config (MTD based) device"
	default n
	---help---
		Provides a /dev/config device for saving / restoring application
		configuration data to a standard MTD device or partition.

if MTD_CONFIG

config MTD_CONFIG_RAM_CONSOLIDATE
	bool "Always use RAM consolidation method (work in progress)"
	default n
	---help---
		When the MTD device used for /dev/config contains more than one
		erase block, the "unused entry" consolidation reserves one erase
		block by default for cleanup purposes.  This consumes the minimum
		amount of RAM, however it "wastes" one erase block on the device.
		(For configurations that have only a single erase block assigned
		to the config device, RAM consolidation is the ONLY option.)

		Another approach is to allow the driver to use the entire MTD
		device (or partition) to save config data, and then allocate a
		RAM buffer (the size of one erase block) to perform the
		consolidation.  Enabling this feature basically trades off RAM
		usage for FLASH usage.  If the MTD device used for config data
		has small erase sizes (4K, etc.) and there is plenty of free RAM
		available, then this is probably a good option.

		Another benefit of this option is it reduces code space a bit
		since the "reserved block" consolidate routine is not needed.

config MTD_CONFIG_ERASEDVALUE
	hex "Erased value of bytes on the MTD device"
	default 0xff
	---help---
		Specifies the value of the erased state of the MTD FLASH.  For
		most FLASH parts, this is 0xff, but could also be zero depending
		on the device.

config MTD_CONFIG_NAMED
	bool "Use item NAMES instead of ID/enumeration in Dev Config device"
	default n
	---help---
		Changes config item identification from ID/INST to NAMED values.

config MTD_CONFIG_NAME_LEN
	int "Dev Config item max name length"
	default 24
	depends on MTD_CONFIG_NAMED
	---help---
		Sets the maximum length of config item names.

endif # MTD_CONFIG

comment "MTD Device Drivers"

menuconfig MTD_NAND
	bool "MTD NAND support"
	depends on ALLOW_BSD_COMPONENTS
	default n
	---help---
		Enable support for NAND FLASH devices.

if MTD_NAND

config MTD_NAND_MAXNUMBLOCKS
	int "Max blocks"
	default 1024
	---help---
		Maximum number of blocks in a device

config MTD_NAND_MAXNUMPAGESPERBLOCK
	int "Max pages per block"
	default 256
	---help---
		Maximum number of pages in one block

config MTD_NAND_MAXPAGEDATASIZE
	int "Max page size"
	default 4096
	---help---
		Maximum size of the data area of one page, in bytes.

config MTD_NAND_MAXPAGESPARESIZE
	int "Max size of spare area"
	default 256
	---help---
		Maximum size of the spare area of one page, in bytes.

config MTD_NAND_MAXSPAREECCBYTES
	int "Max number of ECC bytes"
	default 48
	---help---
		Maximum number of ECC bytes stored in the spare for one single page.

config MTD_NAND_BLOCKCHECK
	bool "Block check"
	default y
	---help---
		Enable support for ECC and bad block checking.

config MTD_NAND_SWECC
	bool "Software ECC support"
	default n if ARCH_NAND_HWECC
	default y if !ARCH_NAND_HWECC
	---help---
		Build in logic to support software calculation of ECC.

config MTD_NAND_HWECC
	bool "Hardware ECC support"
	default n
	depends on ARCH_NAND_HWECC
	---help---
		Build in logic to support hardware calculation of ECC.

config MTD_NAND_MAXSPAREEXTRABYTES
	int "Max extra free bytes"
	default 206
	---help---
		Maximum number of extra free bytes inside the spare area of a page.

config MTD_NAND_EMBEDDEDECC
	bool "Support devices with Embedded ECC"
	default n
	---help---
		Some NAND devices have internal, embedded ECC function.  One (the
		only one supported) is Micron, 4-bit ECC, device size = 1Gb or 2Gb
		or 4Gb.

endif # MTD_NAND

config RAMMTD
	bool "RAM-based MTD driver"
	default n
	---help---
		Build support for a RAM-based MTD driver.

if RAMMTD

config RAMMTD_BLOCKSIZE
	int "RAM MTD block size"
	default 512

config RAMMTD_ERASESIZE
	int "RAM MTD erase block size"
	default 4096

config RAMMTD_ERASESTATE
	hex "Simulated erase state"
	default 0xff

config RAMMTD_FLASHSIM
	bool "RAM MTD FLASH Simulation"
	default n
	---help---
		RAMMTD_FLASHSIM will add some extra logic to improve the level of
		FLASH simulation.

endif # RAMMTD

config FILEMTD
	bool "File-based MTD driver"
	default n
	---help---
		Build support for a File-based MTD driver.

if FILEMTD

config FILEMTD_BLOCKSIZE
	int "File MTD block size"
	default 512

config FILEMTD_ERASESIZE
	int "File MTD erase block size"
	default 4096

config FILEMTD_ERASESTATE
	hex "Simulated erase state"
	default 0xff

endif # FILEMTD

config MTD_AT24XX
	bool "I2C-based AT24xx eeprom"
	default n
	select I2C
	---help---
		Build support for I2C-based AT24CXX EEPROM(at24c32, at24c64,
		at24c128, at24c256)

if MTD_AT24XX

config AT24XX_MULTI
	bool "Multiple AT24XX devices"
	default n
	---help---
		Build in additional support for multiple AT24XX devices, each with
		dynamically allocated device structures with a separate I2C
		addresses (but otherwise identical -- support for multiple, different
		AT24xx, devices not yet supported).

config AT24XX_SIZE
	int "AT24xx size (Kbit)"
	default 64
	---help---
		This is the XX in the AT24Cxx part number.  For example, if you have a
		AT 24C512, then the correct value is 512.  This value is also the capacity
		of the part in kilobits.  For example, the 24C512 supports 512 Kbits or
		512 /8 = 64 KiB.

config AT24XX_ADDR
	hex "AT24XX I2C address"
	default 0x50
	range 0x50 0x57
	depends on !AT24XX_MULTI
	---help---
		The I2C address of the FLASH part.  This is should be 0b01010aaa
		(where aaa is determined by board/pin configuration).

		For accesses to "extended memory" accesses, the driver will set
		bit 3 of this address using 0xb01011aaa as the I2C address.

config AT24XX_EXTENDED
	bool "Extended memory"
	default n
	---help---
		If the device supports extended memory, then this operation may be set
		to enabled the MTDIOC_EXTENDED ioctl() operation.  When the
		extended operation is selected, calls to the driver read method will
		return data from the extended memory region.

config AT24XX_EXTSIZE
	int "Extended memory size (bytes)"
	default 0
	depends on AT24XX_EXTENDED
	---help---
		If the device supports extended memory, then this option provides
		the size of the memory in bytes.

		Other, block-oriented access are not effected by this setting

config AT24XX_FREQUENCY
	int "AT24xx I2C bus frequency"
	default 100000
	---help---
		Set the I2C frequency to use when accessing the AT24CXX EEPROM. This value
		must represent a valid I2C speed (normally less than 400.000) or the driver
		might fail.

endif # MTD_AT24XX

config MTD_AT25
	bool "SPI-based AT25 FLASH"
	default n
	select SPI

if MTD_AT25

config AT25_SPIMODE
	int "AT25 SPI Mode"
	default 0

config AT25_SPIFREQUENCY
	int "AT25 SPI Frequency"
	default 20000000

endif # MTD_AT25

config MTD_AT45DB
	bool "SPI-based AT45DB flash"
	default n
	select SPI

if MTD_AT45DB

config AT45DB_FREQUENCY
	int "AT45DB frequency"
	default 1000000

config AT45DB_PREWAIT
	bool "Enable higher performance write logic"
	default y

config AT45DB_PWRSAVE
	bool "Enable power save"
	default n

endif # MTD_AT45DB

config MTD_IS25XP
	bool "SPI-based IS25XP FLASH"
	default n
	select SPI

if MTD_IS25XP

config IS25XP_SPIMODE
	int "IS25 SPI Mode"
	default 0

config IS25XP_SPIFREQUENCY
	int "IS25 SPI Frequency"
	default 20000000

endif # MTD_IS25XP

config MTD_M25P
	bool "SPI-based M25P/MT25Q FLASH"
	default n
	select SPI

if MTD_M25P

config M25P_SPIMODE
	int "M25P SPI mode"
	default 0

config M25P_SPIFREQUENCY
	int "M25P SPI Frequency"
	default 20000000

config M25P_MANUFACTURER
	hex "M25P manufacturers ID"
	default 0x20
	---help---
		Various manufacturers may have produced the parts.  0x20 is the manufacturer ID
		for the STMicro MP25x serial FLASH.  If, for example, you are using the a Macronix
		International MX25 serial FLASH, the correct manufacturer ID would be 0xc2.

config M25P_MEMORY_TYPE
	hex "M25P memory type ID"
	default 0x20
	---help---
		The memory type for M25 "P" series is 0x20, but the driver also supports "F" series
		devices, such as the EON EN25F80 part which adds a 4K sector erase capability.  The
		memory type for "F" series parts from EON is 0x31.  The 4K sector erase size will
		automatically be enabled when filesystems that can use it are enabled, such as SMART.

config MT25Q_MEMORY_TYPE
	hex "MT25Q memory type ID"
	default 0xBA
	---help---
		The memory type for MT25 "Q" series is 0xBA.

config M25P_SUBSECTOR_ERASE
	bool "Sub-Sector Erase"
	default n
	---help---
		Some devices (such as the EON EN25F80) support a smaller erase block
		size (4K vs 64K).  This option enables support for sub-sector erase.
		The SMART file system can take advantage of this option if it is enabled.

endif # MTD_M25P

config MTD_MX25L
	bool "SPI-based MX25L3233F / MX25L6433F"
	default n
	select SPI
	---help---
		SPI-based driver for Macronix MX25L3233F or MX25L6433F.

if MTD_MX25L

config MX25L_SPIMODE
	int "MX25L SPI mode"
	default 0

config MX25L_SPIFREQUENCY
	int "MX25L SPI Frequency"
	default 20000000

config MX25L_SECTOR512
	bool "Simulate 512 byte Erase Blocks"
	default n

config MX25L_SUBSECTOR_ERASE
	bool "Sub-Sector Erase"
	default n
	---help---
		Some devices (such as the EON EN25F80) support a smaller erase block
		size (4K vs 64K).  This option enables support for sub-sector erase.
		The SMART file system can take advantage of this option if it is enabled.

config MX25L_DEBUG
	bool "Enable driver debug features"
	default n

endif # MTD_MX25L

config MTD_MX35
	bool "SPI-based MX35LF1GE4AB / MX35LF2GE4AB"
	default n
	select SPI
	---help---
		SPI-based driver for Macronix MX35LF1GE4AB or MX35LF2GE4AB.

if MTD_MX35

config MX35_SPIMODE
	int "MX35 SPI mode"
	default 0

config MX35_SPIFREQUENCY
	int "MX35 SPI Frequency"
	default 104000000
	---help---
		SPI frequency for MX35 is 104 MHz.

endif # MTD_MX35

config MTD_S25FL1
	bool "QuadSPI-based S25FL1 FLASH"
	default n

if MTD_S25FL1

config S25FL1_QSPIMODE
	int "S25FL1 QuadSPI Mode"
	default 0

config S25FL1_QSPI_FREQUENCY
	int "S25FL1 QuadSPI Frequency"
	default 108000000
	---help---
		Per data sheet:
		– Normal Read (Serial):
			– 50 MHz clock rate (-40°C to +85°C/105°C)
			– 45 MHz clock rate (-40°C to +125°C)
		– Fast Read (Serial):
			– 108 MHz clock rate (-40°C to +85°C/105°C)
			– 97 MHz clock rate (-40°C to +125°C)
		– Dual Read:
			– 108 MHz clock rate (-40°C to +85°C/105°C)
			– 97 MHz clock rate (-40°C to +125°C)
		– Quad Read:
			– 108 MHz clock rate (-40°C to +85°C/105°C)
			– 97 MHz clock rate for S25FL164K (-40°C to +125°C)

		- Clock frequency for all SPI commands except for Read Data
		  command (0x03) and Fast Read command (0x0b): 108 MHz
		- Clock frequency for Read Data command (0x03): 50 MHz
		- Clock frequency for all Fast Read commands SIO and MIO: 108 MHz

		In this implementation, only "Quad" reads are performed.

config S25FL1_SECTOR512
	bool "Simulate 512 byte Erase Blocks"
	default n

config S25FL1_SCRAMBLE
	bool "Scramble data"
	default n
	---help---
		Requires driver support for data scrambling/descrambling.

config S25FL1_SCRAMBLE_KEY
	hex "Scramble key"
	default 0x0baddead
	depends on S25FL1_SCRAMBLE

endif # MTD_S25FL1

config MTD_N25QXXX
	bool "QuadSPI-based Micron N25QXXX family FLASH"
	default n
	---help---
		Support the N25Q016A, N25Q032A, N25Q064A, N25Q128A, N25Q256A

if MTD_N25QXXX

config N25QXXX_QSPIMODE
	int "N25QXXX QuadSPI Mode"
	default 0
	---help---
		This device can operate in SPI mode 0 or 3.

config N25QXXX_QSPI_FREQUENCY
	int "N25QXXX QuadSPI Frequency"
	default 108000000
	---help---
		- Clock frequency for all SPI commands except for Read Data
		  command (0x03)
		- Clock frequency for Read Data command (0x03): 54 MHz
		In this implementation, only "Quad" reads are performed.

config N25QXXX_SECTOR512
	bool "Simulate 512 byte Erase Blocks"
	default n

endif # MTD_N25QXXX

config MTD_W25QXXXJV
	bool "QuadSPI-based Winbond W25QXXXJV family FLASH"
	default n
	---help---
		Support the W25Q016JV, W25Q032JV, W25Q064JV, W25Q128JV, W25Q256JV, W25Q512JV, W25Q01JV

if MTD_W25QXXXJV

config W25QXXXJV_QSPIMODE
	int "W25QXXXJV QuadSPI Mode"
	default 0
	---help---
		This device can operate in SPI mode 0 or 3.

config W25QXXXJV_QSPI_FREQUENCY
	int "W25QXXXJV QuadSPI Frequency"
	default 133000000
	---help---
		Per data sheet:
		– 133MHz Single, Dual/Quad SPI clocks
		– 266/532MHz equivalent Dual/Quad SPI
		– 66MB/S continuous data transfer rate

config W25QXXXJV_SECTOR512
	bool "Simulate 512 byte Erase Blocks"
	default n

endif # MTD_W25QXXXJV

config MTD_MX25RXX
	bool "QuadSPI-based Macronix MX25RXX family FLASH"
	default n
	---help---
		Support the MX25R6435F chip

if MTD_MX25RXX

config MX25RXX_QSPIMODE
	int "MX25RXX QuadSPI Mode"
	default 0
	---help---
		This device can operate in SPI mode 0 or 3.

config MX25RXX_QSPI_FREQUENCY
	int "MX25RXX QuadSPI Frequency"
	default 33000000
	---help---
		Clock frequency for all SPI commands except for Read Data
		command. Dual and Quad read methods need different frequency
		in low power mode (Only Quad read is supported in this driver).

config MX25RXX_QSPI_READ_FREQUENCY
	int "MX25RXX QuadSPI Read command frequency"
	default 8000000
	---help---
		Clock frequency for read data command.
		Only Quad read is supported in this driver.

config MX25RXX_SECTOR512
	bool "Simulate 512 byte Erase Blocks"
	default n

endif # MTD_MX25RXX

config MTD_SMART
	bool "Sector Mapped Allocation for Really Tiny (SMART) Flash support"
	default n
	---help---
		The MP25x series of Flash devices are typically very small and have a very large
		erase block size.  This causes issues with the standard Flash Translation Layer
		block driver since it tries to allocate a RAM block the size of a flash erase
		block, which is typically 64K.  This block driver uses a different approach
		to sacrifice performance for RAM memory footprint by saving data in sectors
		(typically 2K - 4K based on memory size) and relocating sectors as needed when
		an erase block needs to be erased.

if MTD_SMART

config SMART_DEV_LOOP
	bool "Enable SMART loop device"
	select FILEMTD
	default n
	---help---
		Supports a smart loop device that can be used to export a
		file (or character device) as a SMART block device.

config MTD_SMART_SECTOR_SIZE
	int "SMART Device sector size"
	default 1024
	---help---
		Sets the size of a single allocation on the SMART device.  Larger sector sizes
		reduce overhead per sector, but cause more wasted space with a lot of smaller
		files.

config MTD_SMART_WRITEBUFFER
	bool "Enable SMART write buffering"
	default n
	depends on DRVR_WRITEBUFFER

config MTD_SMART_READAHEAD
	bool "Enable SMART read-ahead buffering"
	default n
	depends on DRVR_READAHEAD

config MTD_SMART_WEAR_LEVEL
	bool "Support FLASH wear leveling"
	depends on MTD_SMART
	default y
	---help---
		Adds extra logic and RAM to guarantee equal wear leveling of the FLASH
		device by recording and monitoring erase block operations and selecting
		sector allocations to ensure all erase blocks are worn evenly.  This will
		evenly wear both dynamic and static data on the device.

if MTD_SMART_WEAR_LEVEL && !SMART_CRC_16

config MTD_SMART_CONVERT_WEAR_FORMAT
	bool "Convert existing non wear leveling FLASH to wear leveling"
	default n
	---help---
		Adds a little extra code which detects an existing SMART format on a device
		that was created prior to the wear leveling implementation.  This conversion
		only works if either no CRC is being used or if CRC-8 is being used as other
		CRC versions use a different header format and require a mksmartfs on the
		device even if an existing format is there.

endif # MTD_SMART_WEAR_LEVEL && !SMART_CRC_16

config MTD_SMART_ENABLE_CRC
	bool "Enable Sector CRC error detection"
	depends on MTD_SMART
	default n
	---help---
		Enables logic to compute and validate a CRC for logical sectors.  The
		CRC is calculated for all bytes in the logical sector.  The CRC size is
		selectable (8-bit, 16-bit, 32-bit).  For added protection, larger CRCs should
		be used with larger (2K - 4K) sector sizes.  Enabling CRC protection will
		cause increased sector relocation and increased erase block erasures since
		directory and wear-level status updates can no longer be performed in-place
		and mandate re-writing the information to a new sector.

		An 8-bit CRC protection scheme can be added to an existing non-CRC formatted
		SMART volume without needing to reformat the drive.  As sectors are re-written
		or relocated, they will be converted to CRC protected sectors.

choice
	prompt "CRC level selection"
	depends on MTD_SMART_ENABLE_CRC
	default SMART_CRC_8
	---help---
		Select the level of CRC protection implemented in the SMART MTD layer.
		Smaller CRC selection uses less overhead per logical sectors, but also has
		a higher probability of not detecting multiple bit errors.  Devices with
		larger logical sector sizes should use a larger CRC.

config SMART_CRC_8
	bool "CRC-8"

config SMART_CRC_16
	bool "CRC-16"

endchoice # CRC level selection

config MTD_SMART_FSCK
	bool "Enable SMART file system check"
	default n
	---help---
		Enables fsck to check and repair the SMART file system.

config MTD_SMART_FSCK_ENABLE_CRC
	bool "Enable SMART file system CRC check during fsck"
	default n
	depends on MTD_SMART_FSCK && MTD_SMART_ENABLE_CRC
	---help---
		Enables CRC check during fsck. It's possible to check the file
		system strictly, but it takes long time to do fsck.

config MTD_SMART_MINIMIZE_RAM
	bool "Minimize SMART RAM usage using logical sector cache"
	depends on MTD_SMART
	default 0
	---help---
		Reduces RAM usage in the SMART MTD layer by replacing the 1-for-1 logical to
		physical sector map with a smaller cache-based structure.  This can save a
		considerable amount of RAM on devices with a large sector count, but at the
		expense of increased read/write times when a cache miss occurs.  If the
		requested logical sector has not been cached, then the device will need to be
		scanned to located it on the physical medium.

config MTD_SMART_SECTOR_CACHE_SIZE
	int "Number of entries in the SMART logical sector cache"
	depends on MTD_SMART_MINIMIZE_RAM
	default 512
	---help---
		Sets the size of the cache used for logical to physical sector mapping.  A
		larger number allows larger files to be "seek"ed randomly without encountering
		cache misses.  Any files larger than CACH_SIZE * SECTOR_SIZE that are sought
		start to end will cause the cache to flush forcing manual scanning of the
		MTD device to find the logical to physical mappings.

config MTD_SMART_SECTOR_PACK_COUNTS
	bool "Pack free and release counts when possible"
	depends on MTD_SMART_MINIMIZE_RAM
	default y
	---help---
		For volumes with 16 sectors per erase block or less, this option causes the
		free sector and released sector counts used for allocation and garbage
		collection to be packed such that two values are stored per byte.  For
		volumes with 16 sectors per erase block, the 4 LSBs are packed and all of
		the high-order bits are packed separately (8 per byte).  This squeezes even
		more RAM out.

config MTD_SMART_SECTOR_ERASE_DEBUG
	bool "Track Erase Block erasure counts"
	depends on MTD_SMART
	default n
	---help---
		Allocates an Erase Block erase count array and keeps track of the number
		of erases per erase block.  This data is then presented on the procfs
		interface.

config MTD_SMART_ALLOC_DEBUG
	bool "RAM Allocation Debug"
	depends on MTD_SMART
	default n
	---help---
		Records all SMART MTD layer allocations for debug purposes and makes them
		accessible from the ProcFS interface if it is enabled.

endif # MTD_SMART

config MTD_RAMTRON
	bool "SPI-based RAMTRON NVRAM Devices FM25V10"
	default n
	select SPI
	---help---
		SPI-based RAMTRON NVRAM Devices FM25V10

if MTD_RAMTRON

config RAMTRON_SETSPEED
	bool "Adjustable bus speed"
	default n
	---help---
		Select an option to provide an ioctl, MTDIOC_SETSPEED call that
		supports dynamic selection of the RAMTRON bus speed.

config RAMTRON_CHUNKING
	bool "Support chunked writes"
	default n
	---help---
		Some Re-RAMs like MB85AS4MT have write buffer size limitation and
		require smaller, "chunked" writes.

endif # MTD_RAMTRON

config MTD_SST25
	bool "SPI-based SST25 FLASH"
	default n
	select SPI

if MTD_SST25

config SST25_SPIMODE
	int "SST25 SPI Mode"
	default 0

config SST25_SPIFREQUENCY
	int "SST25 SPI Frequency"
	default 20000000

config SST25_READONLY
	bool "SST25 Read-Only FLASH"
	default n

config SST25_SECTOR512
	bool "Simulate 512 byte Erase Blocks"
	default n

config SST25_SLOWWRITE
	bool
	default n
	---help---
		There used to be a bug in the current code when using the higher speed AAI
		write sequence. The nature of the bug is that the WRDI instruction is not
		working. At the end of the AAI sequence, the status register continues to
		report that the SST25 is write enabled (WEL bit) and in AAI mode (AAI
		bit).  This has been fixed by David Sidrane!

config SST25_SLOWREAD
	bool
	default n

endif # MTD_SST25

config MTD_SST25XX
	bool "SPI-based SST25XX FLASH (64-MBit and larger)"
	default n
	select SPI
	---help---
		With the 64 MBit and larger parts, SST changed the write mechanism to
		support page write instead of byte/word write like the smaller parts.
		As a result, the SST25 driver is not compatible with the larger density
		parts, and the SST25XX driver must be used instead.

if MTD_SST25XX

config SST25XX_SPIMODE
	int "SST25 SPI Mode"
	default 0

config SST25XX_SPIFREQUENCY
	int "SST25 SPI Frequency"
	default 20000000

config SST25XX_MANUFACTURER
	hex "Manufacturers ID"
	default 0xBF
	---help---
		Various manufacturers may have produced the parts.  0xBF is the manufacturer ID
		for the parts manufactured by SST.

config SST25XX_MEMORY_TYPE
	hex "Memory type ID"
	default 0x25
	---help---
		The memory type for SST25VF065 series is 0x25, but this can be modified if needed
		to support compatible devices from different manufacturers.

endif # MTD_SST25XX

config MTD_SST26
	bool "SPI/QSPI-based SST26XX FLASHes (16,32,64-MBit)"
	default n
	select SPI
	---help---
		These part are also different from SST25 and SST25XX, they support both SPI and QSPI.

if MTD_SST26

config SST26_SPIMODE
	int "SST26 (Q)SPI Mode"
	default 0

config SST26_SPIFREQUENCY
	int "SST26 (Q)SPI Frequency"
	default 64000000

config SST26_MANUFACTURER
	hex "Manufacturers ID"
	default 0xBF
	---help---
		Various manufacturers may have produced the parts.  0xBF is the manufacturer ID
		for the parts manufactured by SST.

config SST26_MEMORY_TYPE
	hex "Memory type ID"
	default 0x26
	---help---
		The memory type for SST26VF0xx series is 0x26, but this can be modified if needed
		to support compatible devices from different manufacturers.

config SST26_DEBUG
	bool "Debug output from the SST26 driver"
	depends on DEBUG_FS
	default n

endif # MTD_SST26

config MTD_SST39FV
	bool "SST39FV NOR FLASH"
	default n
	---help---
		Selects 16-bit SST NOR FLASH.  This includes support for:

		SST39FV1601/SST39FV1602:  2Mb
		SST39FV3201/SST39FV3202:  4Mb

if MTD_SST39FV

config SST39VF_BASE_ADDRESS
	hex "SST39FV bass address"
	default 0x00000000
	---help---
		This is the address where the SST29VF FLASH can be found in memory.

endif # MTD_SST39FV

config MTD_W25
	bool "SPI-based W25 FLASH"
	default n
	select SPI

if MTD_W25

config W25_SPIMODE
	int "W25 SPI Mode"
	default 0

config W25_SPIFREQUENCY
	int "W25 SPI Frequency"
	default 20000000

config W25_READONLY
	bool "W25 Read-Only FLASH"
	default n

config W25_SECTOR512
	bool "Simulate 512 byte Erase Blocks"
	default n

config W25_SLOWREAD
	bool
	default n

endif # MTD_W25

config MTD_GD25
	bool "SPI-based GD25 FLASH"
	default n
	select SPI

if MTD_GD25

config GD25_SPIMODE
	int "GD25 SPI Mode"
	default 0

config GD25_SPIFREQUENCY
	int "GD25 SPI Frequency"
	default 20000000

config GD25_READONLY
	bool "GD25 Read-Only FLASH"
	default n

config GD25_SLOWREAD
	bool
	default n

endif # MTD_GD25

config MTD_GD5F
	bool "SPI-based GD5F nand FLASH"
	default n
	select SPI

if MTD_GD5F

config GD5F_SPIMODE
	int "GD5F SPI Mode"
	default 0

config GD5F_SPIFREQUENCY
	int "GD5F SPI Frequency"
	default 20000000

endif # MTD_GD5F

endif # MTD