2014-03-10 18:25:06 +01:00
|
|
|
#
|
|
|
|
|
# For a description of the syntax of this configuration file,
|
2015-06-28 16:08:57 +02:00
|
|
|
# see the file kconfig-language.txt in the NuttX tools repository.
|
2014-03-10 18:25:06 +01:00
|
|
|
#
|
|
|
|
|
|
|
|
|
|
if ARCH_BOARD_TM4C123G_LAUNCHPAD
|
2014-12-10 22:56:49 +01:00
|
|
|
|
|
|
|
|
config TM4C123G_LAUNCHPAD_AT24_BLOCKMOUNT
|
|
|
|
|
bool "AT24 Serial EEPROM auto-mount"
|
|
|
|
|
default n
|
|
|
|
|
depends on NSH_ARCHINIT && TIVA_I2C0 && MTD_AT24XX
|
|
|
|
|
---help---
|
|
|
|
|
Automatically initialize the AT24 SPI EEPROM driver when NSH starts.
|
|
|
|
|
|
|
|
|
|
The Serial EEPROM was mounted on an external adaptor board and
|
|
|
|
|
connected to the LaunchPad thusly:
|
|
|
|
|
|
|
|
|
|
- VCC -- VCC
|
|
|
|
|
- GND -- GND
|
|
|
|
|
- PB2 -- SCL
|
|
|
|
|
- PB3 -- SDA
|
|
|
|
|
|
|
|
|
|
choice
|
|
|
|
|
prompt "AT24 serial EPPROM configuration"
|
|
|
|
|
default TM4C123G_LAUNCHPAD_AT24_FTL
|
|
|
|
|
depends on TM4C123G_LAUNCHPAD_AT24_BLOCKMOUNT
|
|
|
|
|
|
|
|
|
|
config TM4C123G_LAUNCHPAD_AT24_FTL
|
|
|
|
|
bool "Create AT24 block driver"
|
|
|
|
|
---help---
|
|
|
|
|
Create the MTD driver for the AT24 and "wrap" the AT24 as a standard
|
|
|
|
|
block driver that could then, for example, be mounted using FAT or
|
|
|
|
|
any other file system. Any file system may be used, but there will
|
|
|
|
|
be no wear-leveling.
|
|
|
|
|
|
|
|
|
|
config TM4C123G_LAUNCHPAD_AT24_NXFFS
|
|
|
|
|
bool "Create AT24 NXFFS file system"
|
|
|
|
|
depends on FS_NXFFS
|
|
|
|
|
---help---
|
|
|
|
|
Create the MTD driver for the AT24 and mount the AT24 device as
|
|
|
|
|
a wear-leveling, NuttX FLASH file system (NXFFS). The downside of
|
|
|
|
|
NXFFS is that it can be very slow.
|
|
|
|
|
|
|
|
|
|
endchoice # AT24 serial EPPROM configuration
|
|
|
|
|
|
2022-03-01 02:46:58 +01:00
|
|
|
choice
|
|
|
|
|
prompt "CAN0 RX pin selection"
|
|
|
|
|
default TM4C123G_LAUNCHPAD_CAN0RX_PE4
|
|
|
|
|
depends on TIVA_CAN0
|
|
|
|
|
|
|
|
|
|
config TM4C123G_LAUNCHPAD_CAN0RX_PF0
|
|
|
|
|
bool "Use pin 0 on GPIO port F"
|
|
|
|
|
|
|
|
|
|
config TM4C123G_LAUNCHPAD_CAN0RX_PB4
|
|
|
|
|
bool "Use pin 4 on GPIO port B"
|
|
|
|
|
|
|
|
|
|
config TM4C123G_LAUNCHPAD_CAN0RX_PE4
|
|
|
|
|
bool "Use pin 4 on GPIO port E"
|
|
|
|
|
|
|
|
|
|
endchoice # CAN0 RX pin selection
|
|
|
|
|
|
|
|
|
|
choice
|
|
|
|
|
prompt "CAN0 TX pin selection"
|
|
|
|
|
default TM4C123G_LAUNCHPAD_CAN0TX_PE5
|
|
|
|
|
depends on TIVA_CAN0
|
|
|
|
|
|
|
|
|
|
config TM4C123G_LAUNCHPAD_CAN0TX_PF3
|
|
|
|
|
bool "Use pin 3 on GPIO port F"
|
|
|
|
|
|
|
|
|
|
config TM4C123G_LAUNCHPAD_CAN0TX_PB5
|
|
|
|
|
bool "Use pin 5 on GPIO port B"
|
|
|
|
|
|
|
|
|
|
config TM4C123G_LAUNCHPAD_CAN0TX_PE5
|
|
|
|
|
bool "Use pin 5 on GPIO port E"
|
|
|
|
|
|
|
|
|
|
endchoice # CAN0 TX pin selection
|
|
|
|
|
|
2014-03-10 18:25:06 +01:00
|
|
|
endif
|
