2013-11-18 21:51:38 +01:00
|
|
|
README
|
|
|
|
======
|
|
|
|
|
|
|
|
This README file discusses the port of NuttX to the Olimex LPC-H3131 board.
|
|
|
|
|
2013-11-19 22:52:10 +01:00
|
|
|
NOTE: This is a minimal port to the Olimex LPC-H3131. According to Olimex
|
|
|
|
documentation, the LPC-H3131 is similar in design to the Embedded Artists
|
|
|
|
EA3131. As a consequence, it should be possible to leverage additional
|
|
|
|
functionality from configs/ea3131 without too much difficulty.
|
|
|
|
|
2013-11-18 21:51:38 +01:00
|
|
|
Contents
|
|
|
|
========
|
|
|
|
|
|
|
|
o Development Environment
|
|
|
|
o GNU Toolchain Options
|
|
|
|
o IDEs
|
|
|
|
o NuttX buildroot Toolchain
|
|
|
|
o Boot Sequence
|
|
|
|
o Buttons and LEDs
|
|
|
|
o Image Format
|
|
|
|
o Image Download to ISRAM
|
|
|
|
o Using OpenOCD and GDB
|
|
|
|
o ARM/LPC-H3131-specific Configuration Options
|
|
|
|
o Configurations
|
|
|
|
|
|
|
|
Development Environment
|
|
|
|
=======================
|
|
|
|
|
|
|
|
Either Linux or Cygwin on Windows can be used for the development environment.
|
|
|
|
The source has been built only using the GNU toolchain (see below). Other
|
|
|
|
toolchains will likely cause problems.
|
|
|
|
|
|
|
|
GNU Toolchain Options
|
|
|
|
=====================
|
|
|
|
|
|
|
|
The NuttX make system has been modified to support the following different
|
|
|
|
toolchain options.
|
|
|
|
|
|
|
|
1. The CodeSourcery GNU toolchain,
|
|
|
|
2. The devkitARM GNU toolchain,
|
|
|
|
3. Raisonance GNU toolchain,
|
|
|
|
4. The NuttX buildroot Toolchain (see below), or
|
|
|
|
5. Any generic arm-none-eabi GNU toolchain.
|
|
|
|
|
|
|
|
All testing has been conducted using the NuttX buildroot toolchain. However,
|
|
|
|
the make system is setup to default to use the devkitARM toolchain. To use
|
|
|
|
the CodeSourcery, devkitARM or Raisonance GNU toolchain, you simply need to
|
|
|
|
add one of the following configuration options to your .config (or defconfig)
|
|
|
|
file:
|
|
|
|
|
|
|
|
CONFIG_ARM_TOOLCHAIN_CODESOURCERYW=y : CodeSourcery under Windows
|
|
|
|
CONFIG_ARM_TOOLCHAIN_CODESOURCERYL=y : CodeSourcery under Linux
|
|
|
|
CONFIG_ARM_TOOLCHAIN_DEVKITARM=y : devkitARM under Windows
|
|
|
|
CONFIG_ARM_TOOLCHAIN_BUILDROOT=y : NuttX buildroot under Linux or Cygwin (default)
|
|
|
|
CONFIG_ARM_TOOLCHAIN_GNU_EABIL : Generic arm-none-eabi toolchain for Linux
|
|
|
|
CONFIG_ARM_TOOLCHAIN_GNU_EABIW : Generic arm-none-eabi toolchain for Windows
|
|
|
|
|
|
|
|
If you are not using CONFIG_ARM_TOOLCHAIN_BUILDROOT, then you may also have to modify
|
|
|
|
the PATH in the setenv.h file if your make cannot find the tools.
|
|
|
|
|
|
|
|
The toolchain may also be set using the kconfig-mconf utility (make menuconfig) or by
|
|
|
|
passing CONFIG_ARM_TOOLCHAIN=<toolchain> to make, where <toolchain> is one
|
|
|
|
of CODESOURCERYW, CODESOURCERYL, DEVKITARM, BUILDROOT or GNU_EABI as described
|
|
|
|
above.
|
|
|
|
|
|
|
|
NOTE: the CodeSourcery (for Windows), devkitARM, and Raisonance toolchains are
|
|
|
|
Windows native toolchains. The CodeSourcey (for Linux) and NuttX buildroot
|
|
|
|
toolchains are Cygwin and/or Linux native toolchains. There are several limitations
|
|
|
|
to using a Windows based toolchain in a Cygwin environment. The three biggest are:
|
|
|
|
|
|
|
|
1. The Windows toolchain cannot follow Cygwin paths. Path conversions are
|
|
|
|
performed automatically in the Cygwin makefiles using the 'cygpath' utility
|
|
|
|
but you might easily find some new path problems. If so, check out 'cygpath -w'
|
|
|
|
|
|
|
|
2. Windows toolchains cannot follow Cygwin symbolic links. Many symbolic links
|
|
|
|
are used in Nuttx (e.g., include/arch). The make system works around these
|
|
|
|
problems for the Windows tools by copying directories instead of linking them.
|
|
|
|
But this can also cause some confusion for you: For example, you may edit
|
|
|
|
a file in a "linked" directory and find that your changes had no effect.
|
|
|
|
That is because you are building the copy of the file in the "fake" symbolic
|
|
|
|
directory. If you use a Windows toolchain, you should get in the habit of
|
|
|
|
making like this:
|
|
|
|
|
|
|
|
make clean_context all
|
|
|
|
|
|
|
|
An alias in your .bashrc file might make that less painful.
|
|
|
|
|
|
|
|
3. Dependencies are not made when using Windows versions of the GCC. This is
|
|
|
|
because the dependencies are generated using Windows pathes which do not
|
|
|
|
work with the Cygwin make.
|
|
|
|
|
|
|
|
MKDEP = $(TOPDIR)/tools/mknulldeps.sh
|
|
|
|
|
|
|
|
NOTE 1: The CodeSourcery toolchain (2009q1) does not work with default optimization
|
|
|
|
level of -Os (See Make.defs). It will work with -O0, -O1, or -O2, but not with
|
|
|
|
-Os.
|
|
|
|
|
|
|
|
NOTE 2: The devkitARM toolchain includes a version of MSYS make. Make sure that
|
|
|
|
the paths to Cygwin's /bin and /usr/bin directories appear BEFORE the devkitARM
|
|
|
|
path or will get the wrong version of make.
|
|
|
|
|
|
|
|
Generic arm-none-eabi GNU Toolchain
|
|
|
|
-----------------------------------
|
|
|
|
There are a number of toolchain projects providing support for ARMv4/v5
|
|
|
|
class processors, including:
|
|
|
|
|
|
|
|
GCC ARM Embedded
|
|
|
|
https://launchpad.net/gcc-arm-embedded
|
|
|
|
|
|
|
|
Summon ARM Toolchain
|
|
|
|
https://github.com/esden/summon-arm-toolchain
|
|
|
|
|
|
|
|
Yagarto
|
|
|
|
http://www.yagarto.de
|
|
|
|
|
|
|
|
Others exist for various Linux distributions, MacPorts, etc. Any version
|
|
|
|
based on GCC 4.6.3 or later should work.
|
|
|
|
|
|
|
|
IDEs
|
|
|
|
====
|
|
|
|
|
|
|
|
NuttX is built using command-line make. It can be used with an IDE, but some
|
|
|
|
effort will be required to create the project (There is a simple RIDE project
|
|
|
|
in the RIDE subdirectory).
|
|
|
|
|
|
|
|
Makefile Build
|
|
|
|
--------------
|
|
|
|
Under Eclipse, it is pretty easy to set up an "empty makefile project" and
|
|
|
|
simply use the NuttX makefile to build the system. That is almost for free
|
|
|
|
under Linux. Under Windows, you will need to set up the "Cygwin GCC" empty
|
|
|
|
makefile project in order to work with Windows (Google for "Eclipse Cygwin" -
|
|
|
|
there is a lot of help on the internet).
|
|
|
|
|
|
|
|
Native Build
|
|
|
|
------------
|
|
|
|
Here are a few tips before you start that effort:
|
|
|
|
|
|
|
|
1) Select the toolchain that you will be using in your .config file
|
|
|
|
2) Start the NuttX build at least one time from the Cygwin command line
|
|
|
|
before trying to create your project. This is necessary to create
|
|
|
|
certain auto-generated files and directories that will be needed.
|
|
|
|
3) Set up include pathes: You will need include/, arch/arm/src/lpc31xx,
|
|
|
|
arch/arm/src/common, arch/arm/src/arm, and sched/.
|
|
|
|
4) All assembly files need to have the definition option -D __ASSEMBLY__
|
|
|
|
on the command line.
|
|
|
|
|
|
|
|
Startup files will probably cause you some headaches. The NuttX startup file
|
|
|
|
is arch/arm/src/lpc31xx/lpc31_vectors.S. With RIDE, I have to build NuttX
|
|
|
|
one time from the Cygwin command line in order to obtain the pre-built
|
|
|
|
startup object needed by RIDE.
|
|
|
|
|
|
|
|
NuttX buildroot Toolchain
|
|
|
|
=========================
|
|
|
|
|
|
|
|
A GNU GCC-based toolchain is assumed. The files */setenv.sh should
|
|
|
|
be modified to point to the correct path to the Cortex-M3 GCC toolchain (if
|
|
|
|
different from the default in your PATH variable).
|
|
|
|
|
|
|
|
If you have no Cortex-M3 toolchain, one can be downloaded from the NuttX
|
|
|
|
SourceForge download site (https://sourceforge.net/projects/nuttx/files/buildroot/).
|
|
|
|
This GNU toolchain builds and executes in the Linux or Cygwin environment.
|
|
|
|
|
|
|
|
1. You must have already configured Nuttx in <some-dir>/nuttx.
|
|
|
|
|
|
|
|
cd tools
|
|
|
|
./configure.sh olimex-lpc-h3131/<sub-dir>
|
|
|
|
|
|
|
|
2. Download the latest buildroot package into <some-dir>
|
|
|
|
|
|
|
|
3. unpack the buildroot tarball. The resulting directory may
|
|
|
|
have versioning information on it like buildroot-x.y.z. If so,
|
|
|
|
rename <some-dir>/buildroot-x.y.z to <some-dir>/buildroot.
|
|
|
|
|
|
|
|
4. cd <some-dir>/buildroot
|
|
|
|
|
|
|
|
5. cp configs/arm926t-defconfig-4.2.4 .config
|
|
|
|
|
|
|
|
6. make oldconfig
|
|
|
|
|
|
|
|
7. make
|
|
|
|
|
|
|
|
8. Edit setenv.h, if necessary, so that the PATH variable includes
|
|
|
|
the path to the newly built binaries.
|
|
|
|
|
|
|
|
See the file configs/README.txt in the buildroot source tree. That has more
|
|
|
|
detailed PLUS some special instructions that you will need to follow if you are
|
|
|
|
building a Cortex-M3 toolchain for Cygwin under Windows.
|
|
|
|
|
|
|
|
Boot Sequence
|
|
|
|
=============
|
|
|
|
|
|
|
|
LPC313x has on chip bootrom which loads properly formatted images from multiple
|
|
|
|
sources into SRAM. These sources include including SPI Flash, NOR Flash, UART,
|
|
|
|
USB, SD Card, and NAND Flash.
|
|
|
|
|
|
|
|
In all configurations, NuttX is loaded directly into ISRAM. NuttX is linked
|
|
|
|
to execute from ISRAM, regardless of the boot source.
|
|
|
|
|
|
|
|
Buttons and LEDs
|
|
|
|
================
|
|
|
|
|
|
|
|
Buttons
|
|
|
|
-------
|
|
|
|
|
2013-11-19 02:07:49 +01:00
|
|
|
There are no user buttons on the H3131
|
2013-11-18 21:51:38 +01:00
|
|
|
|
|
|
|
LEDs
|
|
|
|
----
|
|
|
|
|
|
|
|
There are two LEDs on the LPC-H3131 that can be controlled by software:
|
|
|
|
|
|
|
|
LED GPIO
|
|
|
|
---------------- -----
|
|
|
|
LED1 Yellow GPIO17 High output illuminates
|
|
|
|
LED2 Green GPIO18 High output illuminates
|
|
|
|
|
|
|
|
Both can be illuminated by driving the GPIO output to high.
|
|
|
|
|
|
|
|
These LEDs are not used by the board port unless CONFIG_ARCH_LEDS is
|
|
|
|
defined. In that case, the usage by the board port is defined in
|
|
|
|
include/board.h and src/lpc31_leds.c. The LEDs are used to encode
|
|
|
|
OS-related events as follows:
|
|
|
|
|
|
|
|
SYMBOL Meaning LED state
|
|
|
|
LED2 LED1
|
|
|
|
------------------- ----------------------- -------- --------
|
|
|
|
LED_STARTED NuttX has been started OFF OFF
|
|
|
|
LED_HEAPALLOCATE Heap has been allocated OFF OFF
|
|
|
|
LED_IRQSENABLED Interrupts enabled OFF OFF
|
|
|
|
LED_STACKCREATED Idle stack created ON OFF
|
|
|
|
LED_INIRQ In an interrupt N/C N/C
|
|
|
|
LED_SIGNAL In a signal handler N/C N/C
|
|
|
|
LED_ASSERTION An assertion failed N/C N/C
|
|
|
|
LED_PANIC The system has crashed N/C Blinking
|
|
|
|
LED_IDLE MCU is is sleep mode Not used
|
|
|
|
|
|
|
|
Thus if LED2 is statically on, NuttX has successfully booted and is,
|
|
|
|
apparently, running normmally. If LED1 is flashing at approximately
|
|
|
|
2Hz, then a fatal error has been detected and the system has halted.
|
|
|
|
|
|
|
|
NOTE: That LED2 is not used after completion of booting and may
|
|
|
|
be used by other board-specific logic.
|
|
|
|
|
|
|
|
Image Format
|
|
|
|
============
|
|
|
|
|
2013-11-18 22:38:04 +01:00
|
|
|
In order to use the bootrom bootloader, a special header must be added to
|
|
|
|
the beginning of the binary image that includes information about the
|
|
|
|
binary (things like the entry point, the size, and CRC's to verify the image.
|
2013-11-18 21:51:38 +01:00
|
|
|
|
2013-11-18 22:38:04 +01:00
|
|
|
NXP provides a Windows program to append such a header to the binary
|
|
|
|
image. However, (1) that program won't run under Linux, and (2) when I
|
|
|
|
try it under WinXP, Symantec immediately claims that the program is
|
|
|
|
misbehaving and deletes it!
|
2013-11-18 21:51:38 +01:00
|
|
|
|
|
|
|
To work around both of these issues, I have created a small program under
|
2013-11-18 22:38:04 +01:00
|
|
|
configs/olimex-lpc-h3131/tools to add the header. This program can be
|
|
|
|
built under either Linux or Cygwin (and probably other tool environments
|
|
|
|
as well). That tool can be built as follows:
|
2013-11-18 21:51:38 +01:00
|
|
|
|
|
|
|
- cd configs/olimex-lpc-h3131/tools
|
|
|
|
- make
|
|
|
|
|
|
|
|
Then, to build the NuttX binary ready to load with the bootloader, just
|
|
|
|
following these steps:
|
|
|
|
|
|
|
|
- cd tools/ # Configure Nuttx
|
|
|
|
- ./configure.sh olimex-lpc-h3131/ostest # (using the ostest configuration for this example)
|
|
|
|
- cd .. # Set up environment
|
|
|
|
- . ./setenv.sh # (see notes below)
|
|
|
|
- make # Make NuttX. This will produce nuttx.bin
|
|
|
|
- mklpc.sh # Make the bootloader binary (nuttx.lpc)
|
|
|
|
|
|
|
|
NOTES:
|
2013-11-18 22:38:04 +01:00
|
|
|
|
2013-11-18 21:51:38 +01:00
|
|
|
1. setenv.sh just sets up pathes to the toolchain and also to
|
2013-11-18 22:38:04 +01:00
|
|
|
configs/olimex-lpc-h3131/tools where mklpc.sh resides. Use of
|
|
|
|
setenv.sh is optional. If you don't use setenv.sh, then just set
|
|
|
|
your PATH variable appropriately or use the full path to mklpc.sh
|
|
|
|
in the final step.
|
|
|
|
2. You can instruct Symantec to ignore the errors and it will stop
|
|
|
|
quarantining the NXP program.
|
|
|
|
3. The CRC32 logic in configs/olimex-lpc-h3131/tools doesn't seem to
|
|
|
|
work. As a result, the CRC is currently disabled in the header:
|
2013-11-18 21:51:38 +01:00
|
|
|
|
|
|
|
RCS file: /cvsroot/nuttx/nuttx/configs/olimex-lpc-h3131/tools/lpchdr.c,v
|
|
|
|
retrieving revision 1.2
|
|
|
|
diff -r1.2 lpchdr.c
|
|
|
|
264c264
|
|
|
|
< g_hdr.imageType = 0x0000000b;
|
|
|
|
---
|
|
|
|
> g_hdr.imageType = 0x0000000a;
|
|
|
|
|
|
|
|
Image Download to ISRAM
|
|
|
|
=======================
|
|
|
|
|
2013-11-19 02:07:49 +01:00
|
|
|
Assuming that you already have the FTDI driver installed*, then here is the
|
|
|
|
are the steps that I use for loading new code into the LPC-H3131:
|
2013-11-18 21:51:38 +01:00
|
|
|
|
2013-11-19 02:07:49 +01:00
|
|
|
1. Create the bootloader binary, nuttx.lpc, as described above.
|
2013-11-18 22:38:04 +01:00
|
|
|
|
2013-11-19 02:07:49 +01:00
|
|
|
2. With the power off, set the boot jumpers to enable booting from UART.
|
|
|
|
The boot jumpers are the block of three jumper just in-board from the
|
|
|
|
JTAG connector; Jumper pair 1-2 is the pair furthest from the JTAG
|
|
|
|
connector:
|
2013-11-18 22:38:04 +01:00
|
|
|
|
2013-11-19 02:07:49 +01:00
|
|
|
1-2: Closed
|
|
|
|
3-4: Closed
|
|
|
|
5-6: Open
|
2013-11-18 21:51:38 +01:00
|
|
|
|
2013-11-19 02:07:49 +01:00
|
|
|
3. Connected the LPC-H3131 using the FTDI USB port (not the lpc3131 USB port)
|
|
|
|
This will power up the LPC-H3131 and start the bootloader.
|
2013-11-18 21:51:38 +01:00
|
|
|
|
2013-11-19 02:07:49 +01:00
|
|
|
4. Start a terminal emulator (such as TeraTerm) at 115200 8NI.
|
|
|
|
|
|
|
|
5. Reset the LPC-H3131 and you should see:
|
|
|
|
|
|
|
|
LPC31xx READY FOR PLAIN IMAGE>
|
|
|
|
|
|
|
|
6. Send the nuttx.lpc file and you should see:
|
|
|
|
|
|
|
|
Download finished
|
|
|
|
|
|
|
|
That will load the NuttX binary into ISRAM and attempt to execute it.
|
|
|
|
|
|
|
|
*See the LPC313x documentation if you do not have the FTDI driver installed.
|
|
|
|
|
|
|
|
TeraTerm Note: This is how to send a file from TeraTerm. It is essentially
|
|
|
|
step 6 exploded in more detail for the case of TeraTerm:
|
|
|
|
|
|
|
|
1. Start the ROM bootloader as described above.
|
|
|
|
|
|
|
|
2. At the "LPC31xx READY FOR PLAIN IMAGE>" prompt, open the File menu and
|
|
|
|
select the "Send File..." option.
|
|
|
|
|
|
|
|
3. Select the file to send,
|
|
|
|
|
|
|
|
4. Before "Open" -ing the file MAKE SURE TO CHECK THE "Binary" BOX! This
|
|
|
|
has cost me a few hours a few times because I forget to do this. The
|
|
|
|
program will NOT RUN is sent non-binary.
|
|
|
|
|
|
|
|
[NO, I am not SHOUTING. I am just making sure that I never forget to
|
|
|
|
do this again].
|
|
|
|
|
|
|
|
5. "Open"-ing the file will send it to the ROM bootloader.
|
|
|
|
|
|
|
|
6. You should see "Download finished" from the bootloader followed
|
|
|
|
immediately by any serial console output from your program.
|
2013-11-18 21:51:38 +01:00
|
|
|
|
|
|
|
Using OpenOCD and GDB
|
|
|
|
=====================
|
|
|
|
[NOTE: As of this writing, my OpenOCD script does NOT work. It fails
|
|
|
|
because it is unable to halt the LPC3131. So, unfortunately, OpenOCD
|
|
|
|
is not a option right now.]
|
|
|
|
|
|
|
|
I have been using the Olimex ARM-USB-OCD JTAG debugger with the LPC-H3131
|
|
|
|
(http://www.olimex.com). The OpenOCD configuration file is here:
|
|
|
|
tools/armusbocb.cfg. There is also a script on the tools directory that
|
|
|
|
I used to start the OpenOCD daemon on my system called oocd.sh. That
|
|
|
|
script would probably require some modifications to work in another
|
|
|
|
environment:
|
2013-11-18 22:38:04 +01:00
|
|
|
|
2013-11-18 21:51:38 +01:00
|
|
|
- possibly the value of OPENOCD_PATH
|
|
|
|
- If you are working under Linux you will need to change any
|
|
|
|
occurances of `cygpath -w blablabla` to just blablabla
|
|
|
|
|
|
|
|
Then you should be able to start the OpenOCD daemon like:
|
|
|
|
|
|
|
|
configs/olimex-lpc-h3131/tools/oocd.sh $PWD
|
|
|
|
|
|
|
|
Where it is assumed that you are executing oocd.sh from the top level
|
|
|
|
directory where NuttX is installed.
|
|
|
|
|
|
|
|
Once the OpenOCD daemon has been started, you can connect to it via
|
|
|
|
GDB using the following GDB command:
|
|
|
|
|
|
|
|
arm-nuttx-elf-gdb
|
|
|
|
(gdb) target remote localhost:3333
|
|
|
|
|
|
|
|
And you can load the NuttX ELF file:
|
|
|
|
|
|
|
|
(gdb) symbol-file nuttx
|
|
|
|
(gdb) load nuttx
|
|
|
|
|
|
|
|
ARM/LPC-H3131-specific Configuration Options
|
|
|
|
============================================
|
|
|
|
|
|
|
|
CONFIG_ARCH - Identifies the arch/ subdirectory. This should
|
|
|
|
be set to:
|
|
|
|
|
|
|
|
CONFIG_ARCH=arm
|
|
|
|
|
|
|
|
CONFIG_ARCH_family - For use in C code:
|
|
|
|
|
|
|
|
CONFIG_ARCH_ARM=y
|
|
|
|
|
|
|
|
CONFIG_ARCH_architecture - For use in C code:
|
|
|
|
|
|
|
|
CONFIG_ARCH_ARM926EJS=y
|
|
|
|
|
|
|
|
CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
|
|
|
|
|
|
|
|
CONFIG_ARCH_CHIP=lpc313x
|
|
|
|
|
|
|
|
CONFIG_ARCH_CHIP_name - For use in C code
|
|
|
|
|
|
|
|
CONFIG_ARCH_CHIP_LPC3131
|
|
|
|
|
|
|
|
CONFIG_ARCH_BOARD - Identifies the configs subdirectory and
|
|
|
|
hence, the board that supports the particular chip or SoC.
|
|
|
|
|
|
|
|
CONFIG_ARCH_BOARD="olimex-lpc-h3131"
|
|
|
|
|
|
|
|
CONFIG_ARCH_BOARD_name - For use in C code
|
|
|
|
|
|
|
|
CONFIG_ARCH_BOARD_OLIMEX_LPC_H3131
|
|
|
|
|
|
|
|
CONFIG_ARCH_LOOPSPERMSEC - Must be calibrated for correct operation
|
|
|
|
of delay loops
|
|
|
|
|
|
|
|
CONFIG_ENDIAN_BIG - define if big endian (default is little
|
|
|
|
endian)
|
|
|
|
|
|
|
|
CONFIG_RAM_SIZE - For most ARM9 architectures, this describes the
|
|
|
|
size of installed DRAM. For the LPC313X, it is used only to
|
|
|
|
deterimine how to map the executable regions. It is SDRAM size
|
|
|
|
only if you are executing out of the external SDRAM; or it could
|
|
|
|
be NOR FLASH size, external SRAM size, or internal SRAM size.
|
|
|
|
|
|
|
|
CONFIG_RAM_START - The start address of installed DRAM (physical)
|
|
|
|
|
|
|
|
CONFIG_RAM_VSTART - The startaddress of DRAM (virtual)
|
|
|
|
|
|
|
|
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to boards that
|
|
|
|
have LEDs
|
|
|
|
|
|
|
|
CONFIG_ARCH_IRQPRIO - The LPC313x supports interrupt prioritization
|
|
|
|
|
|
|
|
CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
|
|
|
|
stack. If defined, this symbol is the size of the interrupt
|
|
|
|
stack in bytes. If not defined, the user task stacks will be
|
|
|
|
used during interrupt handling.
|
|
|
|
|
|
|
|
CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
|
|
|
|
|
|
|
|
CONFIG_ARCH_BOOTLOADER - Set if you are using a bootloader.
|
|
|
|
|
|
|
|
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.
|
|
|
|
|
|
|
|
CONFIG_ARCH_BUTTONS - Enable support for buttons. Unique to board architecture.
|
|
|
|
|
|
|
|
CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
|
|
|
|
cause a 100 second delay during boot-up. This 100 second delay
|
|
|
|
serves no purpose other than it allows you to calibratre
|
|
|
|
CONFIG_ARCH_LOOPSPERMSEC. You simply use a stop watch to measure
|
|
|
|
the 100 second delay then adjust CONFIG_ARCH_LOOPSPERMSEC until
|
|
|
|
the delay actually is 100 seconds.
|
|
|
|
CONFIG_ARCH_DMA - Support DMA initialization
|
|
|
|
CONFIG_ARCH_LOWVECTORS - define if vectors reside at address 0x0000:00000
|
|
|
|
Undefine if vectors reside at address 0xffff:0000
|
|
|
|
CONFIG_ARCH_ROMPGTABLE - A pre-initialized, read-only page table is available.
|
|
|
|
If defined, then board-specific logic must also define PGTABLE_BASE_PADDR,
|
|
|
|
PGTABLE_BASE_VADDR, and all memory section mapping in a file named
|
|
|
|
board_memorymap.h.
|
|
|
|
|
|
|
|
Individual subsystems can be enabled:
|
|
|
|
|
|
|
|
CONFIG_LPC31_MCI, CONFIG_LPC31_SPI, CONFIG_LPC31_UART
|
|
|
|
|
|
|
|
External memory available on the board (see also CONFIG_MM_REGIONS)
|
|
|
|
|
|
|
|
CONFIG_LPC31_EXTSRAM0 - Select if external SRAM0 is present
|
|
|
|
CONFIG_LPC31_EXTSRAM0HEAP - Select if external SRAM0 should be
|
|
|
|
configured as part of the NuttX heap.
|
|
|
|
CONFIG_LPC31_EXTSRAM0SIZE - Size (in bytes) of the installed
|
|
|
|
external SRAM0 memory
|
|
|
|
CONFIG_LPC31_EXTSRAM1 - Select if external SRAM1 is present
|
|
|
|
CONFIG_LPC31_EXTSRAM1HEAP - Select if external SRAM1 should be
|
|
|
|
configured as part of the NuttX heap.
|
|
|
|
CONFIG_LPC31_EXTSRAM1SIZE - Size (in bytes) of the installed
|
|
|
|
external SRAM1 memory
|
|
|
|
CONFIG_LPC31_EXTDRAM - Select if external SDRAM is present
|
|
|
|
CONFIG_LPC31_EXTDRAMHEAP - Select if external SDRAM should be
|
|
|
|
configured as part of the NuttX heap.
|
|
|
|
CONFIG_LPC31_EXTDRAMSIZE - Size (in bytes) of the installed
|
|
|
|
external SDRAM memory
|
|
|
|
CONFIG_LPC31_EXTNAND - Select if external NAND is present
|
|
|
|
CONFIG_LPC31_EXTNANDSIZE - Size (in bytes) of the installed
|
|
|
|
external NAND memory
|
|
|
|
|
|
|
|
LPC313X specific device driver settings
|
|
|
|
|
|
|
|
CONFIG_UART_SERIAL_CONSOLE - selects the UART for the
|
|
|
|
console and ttys0
|
|
|
|
CONFIG_UART_RXBUFSIZE - Characters are buffered as received.
|
|
|
|
This specific the size of the receive buffer
|
|
|
|
CONFIG_UART_TXBUFSIZE - Characters are buffered before
|
|
|
|
being sent. This specific the size of the transmit buffer
|
|
|
|
CONFIG_UART_BAUD - The configure BAUD of the UART. Must be
|
|
|
|
CONFIG_UART_BITS - The number of bits. Must be either 7 or 8.
|
|
|
|
CONFIG_UART_PARTIY - 0=no parity, 1=odd parity, 2=even parity
|
|
|
|
CONFIG_UART_2STOP - Two stop bits
|
|
|
|
|
|
|
|
Configurations
|
|
|
|
==============
|
|
|
|
|
|
|
|
Configurations
|
|
|
|
==============
|
|
|
|
|
|
|
|
Information Common to All Configurations
|
|
|
|
----------------------------------------
|
|
|
|
Each LPC-H3131 configuration is maintained in a sub-directory and can be
|
|
|
|
selected as follow:
|
|
|
|
|
|
|
|
cd tools
|
|
|
|
./configure.sh olimex-lpc-h3131/<subdir>
|
|
|
|
cd -
|
|
|
|
. ./setenv.sh
|
|
|
|
|
|
|
|
Before sourcing the setenv.sh file above, you should examine it and perform
|
|
|
|
edits as necessary so that TOOLCHAIN_BIN is the correct path to the directory
|
|
|
|
than holds your toolchain binaries.
|
|
|
|
|
|
|
|
And then build NuttX by simply typing the following. At the conclusion of
|
|
|
|
the make, the nuttx binary will reside in an ELF file called, simply, nuttx.
|
|
|
|
|
|
|
|
make
|
|
|
|
|
|
|
|
The <subdir> that is provided above as an argument to the tools/configure.sh
|
|
|
|
must be is one of the following.
|
|
|
|
|
|
|
|
NOTES:
|
|
|
|
|
|
|
|
1. These configurations use the mconf-based configuration tool. To
|
|
|
|
change any of these configurations using that tool, you should:
|
|
|
|
|
|
|
|
a. Build and install the kconfig-mconf tool. See nuttx/README.txt
|
|
|
|
and misc/tools/
|
|
|
|
|
|
|
|
b. Execute 'make menuconfig' in nuttx/ in order to start the
|
|
|
|
reconfiguration process.
|
|
|
|
|
|
|
|
2. Unless stated otherwise, all configurations generate console
|
|
|
|
output on the UART0 associated with the FT232RL USB-to UART
|
|
|
|
converter.
|
|
|
|
|
|
|
|
3. Unless otherwise stated, the configurations are setup for
|
|
|
|
Windows undery Cygwin. This can, however, be easilty reconfigured.
|
|
|
|
|
|
|
|
4. All of these configurations use the Code Sourcery for Windows toolchain
|
|
|
|
(unless stated otherwise in the description of the configuration). That
|
|
|
|
toolchain selection can easily be reconfigured using 'make menuconfig'.
|
|
|
|
Here are the relevant current settings:
|
|
|
|
|
|
|
|
Build Setup:
|
|
|
|
CONFIG_HOST_WINDOS=y : Microsoft Windows
|
|
|
|
CONFIG_WINDOWS_CYGWIN=y : Using Cygwin or other POSIX environment
|
|
|
|
|
|
|
|
System Type -> Toolchain:
|
|
|
|
CONFIG_ARM_TOOLCHAIN_GNU_EABIW=y : GNU EABI toolchain for windows
|
|
|
|
|
|
|
|
The setenv.sh file is available for you to use to set the PATH
|
|
|
|
variable. The path in the that file may not, however, be correct
|
|
|
|
for your installation.
|
|
|
|
|
|
|
|
Configuration sub-directories
|
|
|
|
-----------------------------
|
|
|
|
|
|
|
|
nsh:
|
|
|
|
Configures the NuttShell (nsh) located at examples/nsh. The
|
|
|
|
Configuration enables only the serial NSH interface.
|
2013-11-20 23:24:10 +01:00
|
|
|
|
|
|
|
General Configuration. These are easily change by modifying the NuttX
|
|
|
|
configuration:
|
|
|
|
|
|
|
|
- Console on UART -> UART-to-USB converter
|
|
|
|
- Platform: Windows with Cygwin
|
|
|
|
- Toolchain: CodeSourcery for Windows
|
|
|
|
|
|
|
|
NOTES:
|
2013-11-21 19:45:42 +01:00
|
|
|
1. Built-in applications are not supported by default. To enable NSH
|
|
|
|
built-in applications:
|
|
|
|
|
|
|
|
Binary
|
|
|
|
CONFIG_BUILTIN=y : Support built-in applications
|
|
|
|
|
|
|
|
Application Configuration -> NSH Library
|
|
|
|
CONFIG_NSH_BUILTIN_APPS=y : Enable built-in applications
|
|
|
|
|
|
|
|
2. SDRAM support is not enabled by default. SDRAM support can be enabled
|
|
|
|
by adding the following to your NuttX configuration file:
|
|
|
|
|
2013-11-21 21:46:49 +01:00
|
|
|
[NOTE: There is still something wrong with the SDRAM setup. At present
|
|
|
|
it hangs on the first access from SDRAM during configuration.]
|
|
|
|
|
2013-11-21 19:45:42 +01:00
|
|
|
System Type->LPC31xx Peripheral Support
|
|
|
|
CONFIG_LPC31_EXTDRAM=y : Enable external DRAM support
|
|
|
|
CONFIG_LPC31_EXTDRAMSIZE=33554432 : 256Mbit -> 32Mbyte
|
|
|
|
CONFIG_LPC31_SDRAM_16BIT=y : Organized 16Mbit x 16 bits wide
|
|
|
|
|
|
|
|
Now that you have SDRAM enabled, what are you going to do with it? One
|
|
|
|
thing you can is add it to the heap
|
|
|
|
|
|
|
|
System Type->Heap Configuration
|
|
|
|
CONFIG_LPC31_EXTDRAMHEAP=y : Add the SDRAM to the heap
|
|
|
|
|
|
|
|
Memory Management
|
|
|
|
CONFIG_MM_REGIONS=2 : Two memory regions: ISRAM and SDRAM
|
|
|
|
|
|
|
|
Another thing you could do is to enable the RAM test built-in
|
|
|
|
application:
|
|
|
|
|
|
|
|
3. You can enable the NuttX RAM test that may be used to verify the
|
|
|
|
external SDAM. To do this, keep the SDRAM out of the heap so that
|
|
|
|
it can be tested without crashing programs using the memory.
|
|
|
|
|
|
|
|
First enable built-in applications as described above, then make
|
|
|
|
the following additional modifications to the NuttX configuration:
|
|
|
|
|
|
|
|
System Type->Heap Configuration
|
|
|
|
CONFIG_LPC31_EXTDRAMHEAP=n : Don't add the SDRAM to the heap
|
|
|
|
|
|
|
|
Memory Management
|
|
|
|
CONFIG_MM_REGIONS=1 : One memory regions: ISRAM
|
|
|
|
|
|
|
|
Then enable the RAM test built-in application:
|
|
|
|
|
|
|
|
Application Configuration->System NSH Add-Ons->Ram Test
|
|
|
|
CONFIG_SYSTEM_RAMTEST=y
|
|
|
|
|
|
|
|
In this configuration, the SDRAM is not added to heap and so is not
|
|
|
|
excessible to the applications. So the RAM test can be freely
|
|
|
|
executed against the SRAM memory beginning at address 0x2000:0000
|
|
|
|
(DDR CS):
|
|
|
|
|
|
|
|
nsh> ramtest -h
|
|
|
|
Usage: ramtest [-w|h|b] <hex-address> <decimal-size>
|
|
|
|
|
|
|
|
Where:
|
|
|
|
<hex-address> starting address of the test.
|
|
|
|
<decimal-size> number of memory locations (in bytes).
|
|
|
|
-w Sets the width of a memory location to 32-bits.
|
|
|
|
-h Sets the width of a memory location to 16-bits (default).
|
|
|
|
-b Sets the width of a memory location to 8-bits.
|
|
|
|
|
|
|
|
To test the entire external 256MB SRAM:
|
|
|
|
|
|
|
|
nsh> ramtest -w 30000000 33554432
|
|
|
|
RAMTest: Marching ones: 30000000 33554432
|
|
|
|
RAMTest: Marching zeroes: 30000000 33554432
|
|
|
|
RAMTest: Pattern test: 30000000 33554432 55555555 aaaaaaaa
|
|
|
|
RAMTest: Pattern test: 30000000 33554432 66666666 99999999
|
|
|
|
RAMTest: Pattern test: 30000000 33554432 33333333 cccccccc
|
|
|
|
RAMTest: Address-in-address test: 30000000 33554432
|
|
|
|
|
|
|
|
4. This configuration has been used to test USB host functionaly. USB
|
2013-11-20 23:24:10 +01:00
|
|
|
host is *not* enabled by default. If you will to enable USB host
|
|
|
|
support in the NSH configuration, please modify the NuttX
|
|
|
|
configuration as follows:
|
|
|
|
|
2013-11-29 21:30:09 +01:00
|
|
|
a) Basic USB Host support
|
|
|
|
|
|
|
|
Drivers -> USB Host Driver Support
|
|
|
|
CONFIG_USBHOST=y : General USB host support
|
|
|
|
CONFIG_USBHOST_INT_DISABLE=y : Not needed (unless you use the keyboard)
|
|
|
|
CONFIG_USBHOST_ISOC_DISABLE=y : Not needed (or supported)
|
|
|
|
|
|
|
|
System Type -> Peripherals
|
|
|
|
CONFIG_LPC31_USBOTG=y : Enable the USB OTG peripheral
|
|
|
|
|
|
|
|
System Type -> USB host configuration
|
|
|
|
CONFIG_LPC31_EHCI_BUFSIZE=128
|
|
|
|
CONFIG_LPC31_EHCI_PREALLOCATE=y
|
|
|
|
|
|
|
|
Library Routines
|
|
|
|
CONFIG_SCHED_WORKQUEUE=y : Work queue support is needed
|
|
|
|
CONFIG_SCHED_WORKSTACKSIZE=1536
|
|
|
|
|
|
|
|
b. USB Mass Storage Class. With this class enabled, you can support
|
|
|
|
connection of USB FLASH storage drives. Support for the USB
|
|
|
|
mass storage class is enabled like this:
|
|
|
|
|
|
|
|
Drivers -> USB Host Driver Support
|
|
|
|
CONFIG_USBHOST_MSC=y : Mass storage class support
|
|
|
|
|
|
|
|
The MSC class will work like this. When you first start NSH, you
|
|
|
|
can look at the available devices like this:
|
|
|
|
|
|
|
|
NuttShell (NSH) NuttX-6.31
|
|
|
|
nsh> ls -l /dev
|
|
|
|
/dev:
|
|
|
|
crw-rw-rw- 0 console
|
|
|
|
crw-rw-rw- 0 null
|
|
|
|
crw-rw-rw- 0 ttyS0
|
|
|
|
|
|
|
|
The crw-rw-rw- indicates a readable, write-able character device.
|
|
|
|
|
|
|
|
nsh> ls -l /dev
|
|
|
|
/dev:
|
|
|
|
crw-rw-rw- 0 console
|
|
|
|
crw-rw-rw- 0 null
|
|
|
|
brw-rw-rw- 0 sda
|
|
|
|
crw-rw-rw- 0 ttyS0
|
|
|
|
|
|
|
|
The brw-rw-rw- indicates a readable, write-able block device.
|
|
|
|
This block device can then be mounted like this:
|
|
|
|
|
|
|
|
nsh> mount -t vfat /dev/sda /mnt/flash
|
|
|
|
|
|
|
|
The USB FLASH drive contents are then visible under /mnt/flash and
|
|
|
|
can be operated on with normal file system commands like:
|
|
|
|
|
|
|
|
nsh> mount -t vfat /dev/sda /mnt/flash
|
|
|
|
nsh> cat /mnt/flash/filec.c
|
|
|
|
etc.
|
|
|
|
|
|
|
|
It is recommended that the drive by unmounted BEFORE it is
|
|
|
|
removed. That is not always possible so if the USB FLASH is
|
|
|
|
removed BEFORE the drive is unmounted, the device at /dev/sda will
|
|
|
|
persist in an unusable stack until it is unmounted with the
|
|
|
|
following command (NOTE: If the FLASH drive is re-inserted in
|
|
|
|
this state, it will appear as /dev/sdb):
|
|
|
|
|
|
|
|
nsh> umount /mnt/flash
|
|
|
|
|
|
|
|
c. HID Keyboard support. The following support will enable support
|
|
|
|
for certain keyboard devices (only the so-called "boot" keyboard
|
|
|
|
class is supported):
|
|
|
|
|
|
|
|
Drivers -> USB Host Driver Support
|
|
|
|
CONFIG_USBHOST_HIDKBD=y : HID keyboard class support
|
2013-11-20 23:24:10 +01:00
|
|
|
|
2013-11-29 21:30:09 +01:00
|
|
|
Drivers -> USB Host Driver Support
|
|
|
|
CONFIG_USBHOST_INT_DISABLE=n : Interrupt endpoint support needed
|
2013-11-20 23:24:10 +01:00
|
|
|
|
2013-11-29 21:30:09 +01:00
|
|
|
In this case, when the HID keyboard is installed, you see a new
|
|
|
|
character device called /dev/kbda.
|
2013-11-20 23:24:10 +01:00
|
|
|
|
2013-11-29 21:30:09 +01:00
|
|
|
There is a HID keyboard test example that can be enabled with the
|
|
|
|
following settings. NOTE: In this case, NSH is disabled because
|
|
|
|
the HID keyboard test is a standalone test.
|
2013-11-20 23:24:10 +01:00
|
|
|
|
2013-11-29 21:30:09 +01:00
|
|
|
This selects the HIDKBD example:
|
|
|
|
|
|
|
|
Application Configuration -> Examples
|
|
|
|
CONFIG_EXAMPLES_HIDKBD=y
|
|
|
|
CONFIG_EXAMPLES_HIDKBD_DEVNAME="/dev/kbda"
|
|
|
|
|
|
|
|
RTOS Features
|
|
|
|
CONFIG_USER_ENTRYPOINT="hidkbd_main"
|
|
|
|
|
|
|
|
These settings disable NSH:
|
|
|
|
|
|
|
|
Application Configuration -> Examples
|
|
|
|
CONFIG_EXAMPLES_NSH=n
|
|
|
|
|
|
|
|
Application Configuration -> NSH Library
|
|
|
|
CONFIG_NSH_LIBRARY=y
|
|
|
|
|
|
|
|
Using the HID Keyboard example: Anything typed on the keyboard
|
|
|
|
should be echoed on the serial console. Here is some sample of
|
|
|
|
a session:
|
|
|
|
|
|
|
|
Initialization
|
|
|
|
|
|
|
|
hidkbd_main: Register class drivers
|
|
|
|
hidkbd_main: Initialize USB host keyboard driver
|
|
|
|
hidkbd_main: Start hidkbd_waiter
|
|
|
|
hidkbd_waiter: Running
|
|
|
|
|
|
|
|
The test example will periodically attempt to open /dev/kbda
|
|
|
|
|
|
|
|
Opening device /dev/kbda
|
|
|
|
Failed: 2
|
|
|
|
Opening device /dev/kbda
|
|
|
|
Failed: 2
|
|
|
|
etc.
|
|
|
|
|
|
|
|
The open will fail each time because there is no keyboard
|
|
|
|
attached. When a USB keyboard is attached, the open of /dev/kbda
|
|
|
|
will succeed and the test will begin echoing data to the serial
|
|
|
|
console:
|
|
|
|
|
|
|
|
hidkbd_waiter: connected
|
|
|
|
Opening device /dev/kbda
|
|
|
|
Device /dev/kbda opened
|
|
|
|
|
|
|
|
For example, this text was entered from the keyboard:
|
|
|
|
|
|
|
|
Now is the time for all good men to come to the aid of their party.
|
|
|
|
|
|
|
|
Then when the device is removed, the test will resume attempting
|
|
|
|
to open the driver until the next time it is connected
|
|
|
|
|
|
|
|
Closing device /dev/kbda: -1
|
|
|
|
Opening device /dev/kbda
|
|
|
|
Failed: 19
|
|
|
|
hidkbd_waiter: disconnected
|
|
|
|
|
|
|
|
Opening device /dev/kbda
|
|
|
|
Failed: 2
|
|
|
|
etc.
|
|
|
|
|
|
|
|
d. The USB monitor can also be enabled:
|
2013-11-20 23:24:10 +01:00
|
|
|
|
|
|
|
Drivers -> USB Host Driver Support
|
|
|
|
CONFIG_USBHOST_TRACE=y
|
|
|
|
CONFIG_USBHOST_TRACE_NRECORDS=128
|
|
|
|
CONFIG_USBHOST_TRACE_VERBOSE=y
|
|
|
|
|
|
|
|
Application Configuration -> System Add-Ons
|
|
|
|
CONFIG_SYSTEM_USBMONITOR=y
|
|
|
|
CONFIG_SYSTEM_USBMONITOR_INTERVAL=1
|
2013-11-27 20:14:23 +01:00
|
|
|
|
|
|
|
NOTE: I have found that if you enable USB DEBUG and/or USB tracing,
|
|
|
|
the resulting image requires to much memory to execute out of
|
|
|
|
internal SRAM. I was able to get the configurations to run out of
|
|
|
|
SRAM with debug/tracing enabled by carefully going through the
|
|
|
|
configuration and reducing stack sizes, disabling unused OS features,
|
|
|
|
disabling un-necessary NSH commands, etc.
|
2013-11-29 21:30:09 +01:00
|
|
|
|
|
|
|
5. Making the Configuration Smaller. This configuration runs out of
|
|
|
|
internal SRAM. If you enable many features, then your code image
|
|
|
|
may outgrow the available SRAM; even if the code can be loaded into
|
|
|
|
SRAM, it may still fail at runtime due to insufficient memory.
|
|
|
|
|
|
|
|
Since SDRAM is not currently working (see above) and NAND support
|
|
|
|
has not be integrated, the only really option is to put NSH "on a
|
|
|
|
diet" to reduct the size so that it will fit into memory.
|
|
|
|
|
|
|
|
Here are a few things you can do:
|
|
|
|
|
|
|
|
1. Try using smaller stack sizes,
|
|
|
|
|
|
|
|
2. Disable operating system features. Here some that can go:
|
|
|
|
|
|
|
|
CONFIG_DISABLE_ENVIRON=y
|
|
|
|
CONFIG_DISABLE_MQUEUE=y
|
|
|
|
CONFIG_DISABLE_POSIX_TIMERS=y
|
|
|
|
CONFIG_DISABLE_PTHREAD=y
|
|
|
|
CONFIG_MQ_MAXMSGSIZE=0
|
|
|
|
CONFIG_NPTHREAD_KEYS=0
|
|
|
|
CONFIG_NUNGET_CHARS=0
|
|
|
|
CONFIG_PREALLOC_MQ_MSGS=0
|
|
|
|
|
|
|
|
3. Disable NSH commands. I can life fine without these:
|
|
|
|
|
|
|
|
CONFIG_NSH_DISABLE_ADDROUTE=y
|
|
|
|
CONFIG_NSH_DISABLE_CD=y
|
|
|
|
CONFIG_NSH_DISABLE_CMP=y
|
|
|
|
CONFIG_NSH_DISABLE_CP=y
|
|
|
|
CONFIG_NSH_DISABLE_DD=y
|
|
|
|
CONFIG_NSH_DISABLE_DELROUTE=y
|
|
|
|
CONFIG_NSH_DISABLE_EXEC=y
|
|
|
|
CONFIG_NSH_DISABLE_EXIT=y
|
|
|
|
CONFIG_NSH_DISABLE_GET=y
|
|
|
|
CONFIG_NSH_DISABLE_HEXDUMP=y
|
|
|
|
CONFIG_NSH_DISABLE_IFCONFIG=y
|
|
|
|
CONFIG_NSH_DISABLE_LOSETUP=y
|
|
|
|
CONFIG_NSH_DISABLE_MB=y
|
|
|
|
CONFIG_NSH_DISABLE_MH=y
|
|
|
|
CONFIG_NSH_DISABLE_MKFIFO=y
|
|
|
|
CONFIG_NSH_DISABLE_MKRD=y
|
|
|
|
CONFIG_NSH_DISABLE_NSFMOUNT=y
|
|
|
|
CONFIG_NSH_DISABLE_PING=y
|
|
|
|
CONFIG_NSH_DISABLE_PUT=y
|
|
|
|
CONFIG_NSH_DISABLE_PWD=y
|
|
|
|
CONFIG_NSH_DISABLE_RM=y
|
|
|
|
CONFIG_NSH_DISABLE_RMDIR=y
|
|
|
|
CONFIG_NSH_DISABLE_SET=y
|
|
|
|
CONFIG_NSH_DISABLE_SH=y
|
|
|
|
CONFIG_NSH_DISABLE_SLEEP=y
|
|
|
|
CONFIG_NSH_DISABLE_TEST=y
|
|
|
|
CONFIG_NSH_DISABLE_UNSET=y
|
|
|
|
CONFIG_NSH_DISABLE_USLEEP=y
|
|
|
|
CONFIG_NSH_DISABLE_WGET=y
|
|
|
|
CONFIG_NSH_DISABLE_XD=y
|