nuttx/arch/arm/src/samv7/sam_gpio.c

572 lines
16 KiB
C
Raw Normal View History

2015-03-09 02:12:30 +01:00
/****************************************************************************
* arch/arm/src/samv7/sam_gpio.c
* General Purpose Input/Output (GPIO) logic for the SAMV71
*
* Copyright (C) 2015 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
****************************************************************************/
/****************************************************************************
* Included Files
****************************************************************************/
#include <nuttx/config.h>
#include <stdint.h>
#include <time.h>
#include <errno.h>
#include <debug.h>
#include <nuttx/arch.h>
#include <arch/board/board.h>
#include "up_internal.h"
#include "up_arch.h"
#include "sam_gpio.h"
#include "chip/sam_pio.h"
/****************************************************************************
* Pre-processor Definitions
****************************************************************************/
/****************************************************************************
* Private Types
****************************************************************************/
/****************************************************************************
* Private Data
****************************************************************************/
#ifdef CONFIG_DEBUG_GPIO
static const char g_portchar[SAMV7_NPIO] =
{
'A'
#if SAMV7_NPIO > 1
, 'B'
#endif
#if SAMV7_NPIO > 2
, 'C'
#endif
#if SAMV7_NPIO > 3
, 'D'
#endif
#if SAMV7_NPIO > 4
, 'E'
#endif
};
#endif
/****************************************************************************
* Public Data
****************************************************************************/
const uintptr_t g_portbase[SAMV7_NPIO] =
2015-03-09 02:12:30 +01:00
{
SAM_PIOA_BASE
#if SAMV7_NPIO > 1
, SAM_PIOB_BASE
#endif
#if SAMV7_NPIO > 2
, SAM_PIOC_BASE
#endif
#if SAMV7_NPIO > 3
, SAM_PIOD_BASE
#endif
#if SAMV7_NPIO > 4
, SAM_PIOE_BASE
#endif
};
/****************************************************************************
* Private Function Prototypes
****************************************************************************/
/****************************************************************************
* Name: sam_configinput
*
* Description:
* Configure a GPIO input pin based on bit-encoded description of the pin.
*
****************************************************************************/
static inline int sam_configinput(uintptr_t base, uint32_t pin,
gpio_pinset_t cfgset)
{
#ifdef GPIO_HAVE_SCHMITT
uint32_t regval;
#endif
/* Disable interrupts on the pin */
putreg32(pin, base + SAM_PIO_IDR_OFFSET);
/* Enable/disable the pull-up as requested */
if ((cfgset & GPIO_CFG_PULLUP) != 0)
{
putreg32(pin, base + SAM_PIO_PUER_OFFSET);
}
else
{
putreg32(pin, base + SAM_PIO_PUDR_OFFSET);
}
#ifdef GPIO_HAVE_PULLDOWN
/* Enable/disable the pull-down as requested */
if ((cfgset & GPIO_CFG_PULLDOWN) != 0)
{
putreg32(pin, base + SAM_PIO_PPDER_OFFSET);
}
else
{
putreg32(pin, base + SAM_PIO_PPDDR_OFFSET);
}
#endif
/* Check if filtering should be enabled */
if ((cfgset & GPIO_CFG_DEGLITCH) != 0)
{
putreg32(pin, base + SAM_PIO_IFER_OFFSET);
}
else
{
putreg32(pin, base + SAM_PIO_IFDR_OFFSET);
}
#ifdef GPIO_HAVE_SCHMITT
/* Enable/disable the Schmitt trigger */
regval = getreg32(base + SAM_PIO_SCHMITT_OFFSET);
if ((cfgset & GPIO_CFG_PULLDOWN) != 0)
{
regval |= pin;
}
else
{
regval &= ~pin;
}
putreg32(regval, base + SAM_PIO_SCHMITT_OFFSET);
#endif
#ifdef GPIO_HAVE_DRIVER
/* Reset output drive strength (PIO outputs only) */
regval = getreg32(base + SAM_PIO_DRIVER_OFFSET);
regval &= ~pin;
putreg32(regval, base + SAM_PIO_DRIVER_OFFSET);
#endif
/* Configure the pin as an input and enable the GPIO function */
putreg32(pin, base + SAM_PIO_ODR_OFFSET);
putreg32(pin, base + SAM_PIO_PER_OFFSET);
/* To-Do: If DEGLITCH is selected, need to configure DIFSR, SCIFSR, and
* IFDGSR registers. This would probably best be done with
* another, new API... perhaps sam_configfilter()
*/
return OK;
}
/****************************************************************************
* Name: sam_configoutput
*
* Description:
* Configure a GPIO output pin based on bit-encoded description of the pin.
*
****************************************************************************/
static inline int sam_configoutput(uintptr_t base, uint32_t pin,
gpio_pinset_t cfgset)
{
#ifdef GPIO_HAVE_DRIVER
uint32_t regval;
#endif
/* Disable interrupts on the pin */
putreg32(pin, base + SAM_PIO_IDR_OFFSET);
/* Enable/disable the pull-up as requested */
if ((cfgset & GPIO_CFG_PULLUP) != 0)
{
putreg32(pin, base + SAM_PIO_PUER_OFFSET);
}
else
{
putreg32(pin, base + SAM_PIO_PUDR_OFFSET);
}
#ifdef GPIO_HAVE_PULLDOWN
/* Enable/disable the pull-down as requested */
if ((cfgset & GPIO_CFG_PULLDOWN) != 0)
{
putreg32(pin, base + SAM_PIO_PPDER_OFFSET);
}
else
{
putreg32(pin, base + SAM_PIO_PPDDR_OFFSET);
}
#endif
/* Enable the open drain driver if requrested */
if ((cfgset & GPIO_CFG_OPENDRAIN) != 0)
{
putreg32(pin, base + SAM_PIO_MDER_OFFSET);
}
else
{
putreg32(pin, base + SAM_PIO_MDDR_OFFSET);
}
/* Set default value */
if ((cfgset & GPIO_OUTPUT_SET) != 0)
{
putreg32(pin, base + SAM_PIO_SODR_OFFSET);
}
else
{
putreg32(pin, base + SAM_PIO_CODR_OFFSET);
}
#ifdef GPIO_HAVE_DRIVER
/* Select the pin output drive strength */
regval = getreg32(base + SAM_PIO_DRIVER_OFFSET);
if ((cfgset & GPIO_OUTPUT_DRIVE) != GPIO_OUTPUT_LOW_DRIVE)
{
regval |= pin;
}
else
{
regval &= ~pin;
}
putreg32(regval, base + SAM_PIO_DRIVER_OFFSET);
#endif
/* Configure the pin as an output and enable the GPIO function */
putreg32(pin, base + SAM_PIO_OER_OFFSET);
putreg32(pin, base + SAM_PIO_PER_OFFSET);
return OK;
}
/****************************************************************************
* Name: sam_configperiph
*
* Description:
* Configure a GPIO pin driven by a peripheral A or B signal based on
* bit-encoded description of the pin.
*
****************************************************************************/
static inline int sam_configperiph(uintptr_t base, uint32_t pin,
gpio_pinset_t cfgset)
{
uint32_t regval;
/* Disable interrupts on the pin */
putreg32(pin, base + SAM_PIO_IDR_OFFSET);
/* Enable/disable the pull-up as requested */
if ((cfgset & GPIO_CFG_PULLUP) != 0)
{
putreg32(pin, base + SAM_PIO_PUER_OFFSET);
}
else
{
putreg32(pin, base + SAM_PIO_PUDR_OFFSET);
}
#ifdef GPIO_HAVE_PULLDOWN
/* Enable/disable the pull-down as requested */
if ((cfgset & GPIO_CFG_PULLDOWN) != 0)
{
putreg32(pin, base + SAM_PIO_PPDER_OFFSET);
}
else
{
putreg32(pin, base + SAM_PIO_PPDDR_OFFSET);
}
#endif
#ifdef GPIO_HAVE_DRIVER
/* Reset output drive strength (PIO outputs only) */
regval = getreg32(base + SAM_PIO_DRIVER_OFFSET);
regval &= ~pin;
putreg32(regval, base + SAM_PIO_DRIVER_OFFSET);
#endif
#ifdef GPIO_HAVE_PERIPHCD
/* Configure pin, depending upon the peripheral A, B, C or D
*
* PERIPHA: ABCDSR1[n] = 0 ABCDSR2[n] = 0
* PERIPHB: ABCDSR1[n] = 1 ABCDSR2[n] = 0
* PERIPHC: ABCDSR1[n] = 0 ABCDSR2[n] = 1
* PERIPHD: ABCDSR1[n] = 1 ABCDSR2[n] = 1
*/
regval = getreg32(base + SAM_PIO_ABCDSR1_OFFSET);
if ((cfgset & GPIO_MODE_MASK) == GPIO_PERIPHA ||
(cfgset & GPIO_MODE_MASK) == GPIO_PERIPHC)
{
regval &= ~pin;
}
else
{
regval |= pin;
}
putreg32(regval, base + SAM_PIO_ABCDSR1_OFFSET);
regval = getreg32(base + SAM_PIO_ABCDSR2_OFFSET);
if ((cfgset & GPIO_MODE_MASK) == GPIO_PERIPHA ||
(cfgset & GPIO_MODE_MASK) == GPIO_PERIPHB)
{
regval &= ~pin;
}
else
{
regval |= pin;
}
putreg32(regval, base + SAM_PIO_ABCDSR2_OFFSET);
#else
/* Configure pin, depending upon the peripheral A or B:
*
* PERIPHA: ABSR[n] = 0
* PERIPHB: ABSR[n] = 1
*/
regval = getreg32(base + SAM_PIO_ABSR_OFFSET);
if ((cfgset & GPIO_MODE_MASK) == GPIO_PERIPHA)
{
regval &= ~pin;
}
else
{
regval |= pin;
}
putreg32(regval, base + SAM_PIO_ABSR_OFFSET);
#endif
/* Disable PIO functionality */
putreg32(pin, base + SAM_PIO_PDR_OFFSET);
return OK;
}
/****************************************************************************
* Global Functions
****************************************************************************/
/****************************************************************************
* Name: sam_configgpio
*
* Description:
* Configure a GPIO pin based on bit-encoded description of the pin.
*
****************************************************************************/
int sam_configgpio(gpio_pinset_t cfgset)
{
uintptr_t base = sam_gpio_base(cfgset);
uint32_t pin = sam_gpio_pinmask(cfgset);
irqstate_t flags;
int ret;
/* Disable interrupts to prohibit re-entrance. */
flags = irqsave();
/* Enable writing to GPIO registers */
putreg32(PIO_WPMR_WPKEY, base + SAM_PIO_WPMR_OFFSET);
/* Handle the pin configuration according to pin type */
switch (cfgset & GPIO_MODE_MASK)
{
case GPIO_ALTERNATE:
case GPIO_INPUT:
ret = sam_configinput(base, pin, cfgset);
break;
case GPIO_OUTPUT:
ret = sam_configoutput(base, pin, cfgset);
break;
case GPIO_PERIPHA:
case GPIO_PERIPHB:
#ifdef GPIO_HAVE_PERIPHCD
case GPIO_PERIPHC:
case GPIO_PERIPHD:
#endif
ret = sam_configperiph(base, pin, cfgset);
break;
default:
ret = -EINVAL;
break;
}
/* Disable writing to GPIO registers */
putreg32(PIO_WPMR_WPEN | PIO_WPMR_WPKEY, base + SAM_PIO_WPMR_OFFSET);
irqrestore(flags);
return ret;
}
/****************************************************************************
* Name: sam_gpiowrite
*
* Description:
* Write one or zero to the selected GPIO pin
*
****************************************************************************/
void sam_gpiowrite(gpio_pinset_t pinset, bool value)
{
uintptr_t base = sam_gpio_base(pinset);
uint32_t pin = sam_gpio_pinmask(pinset);
if (value)
{
putreg32(pin, base + SAM_PIO_SODR_OFFSET);
}
else
{
putreg32(pin, base + SAM_PIO_CODR_OFFSET);
}
}
/****************************************************************************
* Name: sam_gpioread
*
* Description:
* Read one or zero from the selected GPIO pin
*
****************************************************************************/
bool sam_gpioread(gpio_pinset_t pinset)
{
uintptr_t base = sam_gpio_base(pinset);
uint32_t pin = sam_gpio_pinmask(pinset);
uint32_t regval;
if ((pinset & GPIO_MODE_MASK) == GPIO_OUTPUT)
{
regval = getreg32(base + SAM_PIO_ODSR_OFFSET);
}
else
{
regval = getreg32(base + SAM_PIO_PDSR_OFFSET);
}
return (regval & pin) != 0;
}
/************************************************************************************
* Function: sam_dumpgpio
*
* Description:
* Dump all GPIO registers associated with the base address of the provided pinset.
*
************************************************************************************/
#ifdef CONFIG_DEBUG_GPIO
int sam_dumpgpio(uint32_t pinset, const char *msg)
{
irqstate_t flags;
uintptr_t base;
unsigned int port;
/* Get the base address associated with the PIO port */
port = (pinset & GPIO_PORT_MASK) >> GPIO_PORT_SHIFT;
base = SAM_PION_BASE(port);
/* The following requires exclusive access to the GPIO registers */
flags = irqsave();
lldbg("PIO%c pinset: %08x base: %08x -- %s\n",
g_portchar[port], pinset, base, msg);
lldbg(" PSR: %08x OSR: %08x IFSR: %08x ODSR: %08x\n",
getreg32(base + SAM_PIO_PSR_OFFSET), getreg32(base + SAM_PIO_OSR_OFFSET),
getreg32(base + SAM_PIO_IFSR_OFFSET), getreg32(base + SAM_PIO_ODSR_OFFSET));
lldbg(" PDSR: %08x IMR: %08x ISR: %08x MDSR: %08x\n",
getreg32(base + SAM_PIO_PDSR_OFFSET), getreg32(base + SAM_PIO_IMR_OFFSET),
getreg32(base + SAM_PIO_ISR_OFFSET), getreg32(base + SAM_PIO_MDSR_OFFSET));
lldbg(" ABCDSR: %08x %08x IFSCSR: %08x PPDSR: %08x\n",
getreg32(base + SAM_PIO_ABCDSR1_OFFSET), getreg32(base + SAM_PIO_ABCDSR2_OFFSET),
getreg32(base + SAM_PIO_IFSCSR_OFFSET), getreg32(base + SAM_PIO_PPDSR_OFFSET));
lldbg(" PUSR: %08x SCDR: %08x OWSR: %08x AIMMR: %08x\n",
getreg32(base + SAM_PIO_PUSR_OFFSET), getreg32(base + SAM_PIO_SCDR_OFFSET),
getreg32(base + SAM_PIO_OWSR_OFFSET), getreg32(base + SAM_PIO_AIMMR_OFFSET));
lldbg(" ESR: %08x LSR: %08x ELSR: %08x FELLSR: %08x\n",
getreg32(base + SAM_PIO_ESR_OFFSET), getreg32(base + SAM_PIO_LSR_OFFSET),
getreg32(base + SAM_PIO_ELSR_OFFSET), getreg32(base + SAM_PIO_FELLSR_OFFSET));
lldbg(" FRLHSR: %08x LOCKSR: %08x WPMR: %08x WPSR: %08x\n",
getreg32(base + SAM_PIO_FRLHSR_OFFSET), getreg32(base + SAM_PIO_LOCKSR_OFFSET),
getreg32(base + SAM_PIO_WPMR_OFFSET), getreg32(base + SAM_PIO_WPSR_OFFSET));
lldbg(" PCMR: %08x PCIMR: %08x PCISR: %08x PCRHR: %08x\n",
getreg32(base + SAM_PIO_PCMR_OFFSET), getreg32(base + SAM_PIO_PCIMR_OFFSET),
getreg32(base + SAM_PIO_PCISR_OFFSET), getreg32(base + SAM_PIO_PCRHR_OFFSET));
2015-03-09 02:32:05 +01:00
lldbg("SCHMITT: %08x DRIVER:%08x\n",
getreg32(base + SAM_PIO_SCHMITT_OFFSET), getreg32(base + SAM_PIO_DRIVER_OFFSET));
lldbg(" KER: %08x KRCR: %08x KDR: %08x KIMR: %08x\n",
getreg32(base + SAM_PIO_KER_OFFSET), getreg32(base + SAM_PIO_KRCR_OFFSET),
getreg32(base + SAM_PIO_KDR_OFFSET), getreg32(base + SAM_PIO_KIMR_OFFSET));
lldbg(" KSR: %08x KKPR: %08x KKRR: %08x\n",
getreg32(base + SAM_PIO_KSR_OFFSET), getreg32(base + SAM_PIO_KKPR_OFFSET),
getreg32(base + SAM_PIO_KKRR_OFFSET));
lldbg(" PCMR: %08x PCIMR: %08x PCISR: %08x PCRHR: %08x\n",
getreg32(base + SAM_PIO_PCMR_OFFSET), getreg32(base + SAM_PIO_PCIMR_OFFSET),
getreg32(base + SAM_PIO_PCISR_OFFSET), getreg32(base + SAM_PIO_PCRHR_OFFSET));
2015-03-09 02:12:30 +01:00
irqrestore(flags);
return OK;
}
#endif